Scribd
Upload
193 views2 pages

Siprotec 7ss85 Profile

Low Impedance

Uploaded by

M Kashif Junaid
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
193 views2 pages

Siprotec 7ss85 Profile

Low Impedance

Uploaded by

M Kashif Junaid
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SIPROTEC 7SS85

Low Impedance Centralized Busbar Protection

www.siemens.com/siprotec

Description
The SIPROTEC 7SS85 busbar protection is a selective, safe
and fast protection against busbar short circuits in medi-
um, high and extra-high voltage systems with a large
variety of busbar configurations.
Selection of the device base functionalities (significant
properties) and the modular hardware structure permit
optimum adaptation of the SIPROTEC 7SS85 to a large
variety of system configurations and functional require-
ments up to a comprehensive station protection.
Configurations
The SIPROTEC 7SS85 is suited for the following system
configurations:
• Single busbars with/without transfer busbar
• Double busbars with/without transfer busbar Busbar Protection SIPROTEC 7SS85

• Triple busbars
• Breaker-and-a-half layout method
• Dual circuit-breaker systems and one or two current Functions
transformer(s) per feeder • The table "Functions and Templates" shows all
• Truck-Type Switchgear functions that are available in the SIPROTEC 7SS85. All
functions can be configured as required with DIGSI 5
• Systems with combined busbars (alternatively
main/transfer busbar) • Using some functions requires the appropriate num-
ber of free function points to be available in the
• T circuit arrangements
device. The function point calculator in the online
• H connection arrangement with busbar coupler or configurator provides support in determining the
disconnection required number of function points for your device
• Ring busbars • The necessary function points are also shown during
project engineering with DIGSI 5
Characteristic Key Values of SIPROTEC 7SS85
• Phase-selective measurement and display
• Selective tripping of faulty bus zones
Selective and safe

• Disconnector-independent check zone as additional • Various control possibilities, such as bay out of order,
tripping criterion acquisition blocking from disconnectors and circuit
breakers, blocking of protection zones or circuit-
• Shortest tripping times (<7 ms) to ensure network
breaker failure protection, make the adaptation to op-
stability and minimize damage to the system
erationally caused special states of your system easier
• Highest stability in case of external faults, even in • Optional 1/3-pole or 3-pole circuit-breaker failure
case of transformer saturation, through stabilization protection using the integrated disconnector image to
with flowing currents trip all circuit breakers of the busbar section affected
• Operate curve with freely adjustable characteristic • Optional end-fault protection for the protection of the
curve sections section between circuit breaker and current trans-
• Additional operate curve with increased sensitivity for former for feeders and bus couplers
low current faults, for example in resistance-grounded • Direct tripping of protection zones through external
power systems signals
• Fast recognition of internal and external faults re- • Release of the tripping of a protection zone through
quires only 2 ms of saturation-free time of the current additional external signals
transformer
• Release of tripping through additional, external phase-
• Using closed iron core or linearized current transform- selective signals
ers in a plant is possible
• Optional phase/ground overcurrent protection for
• Adaptation of different current transformer ratios per each bay
parameterization
• Optional cross stabilization as additional tripping
• Three interacting methods of measurement allow release in 3-pole encapsulated gas-insulated switch-
minimum tripping times after busbar faults and en- gear
sure maximum stability in case of large short-circuit
• Optional bus coupler differential protection for fault
currents
clearing in couplers with two current transformers
• The integrated circuit-breaker failure protection rec-
ognizes circuit-breaker faults in the event of a busbar Benefits
short circuit and provides a trip signal for the circuit • Safety by measuring methods proven and reliable for
breaker at the line end. The adjacent busbar trips if a 25 years
coupling circuit breaker fails
• Simple creation and adaptation of the configuration
• There is extensive monitoring of current transformer
by the user over the entire service life
circuits, measured value acquisition and processing,
and trip circuits. This prevents the protection from • Clearly structured by fully graphical engineering and
functioning too tightly or too loosely, which reduces online plant visualization with DIGSI 5
the effort for routine checks
• Protection of up to 20 feeders with a single device

For all products using


security features of
OpenSSL, the
Siemens AG following shall apply:
Energy Management Division This product includes
Freyeslebenstraße 1 software developed
91058 Erlangen, Germany by the OpenSSL
Project for use in the
SIPROTEC 7SS85 profile E7.5.docx OpenSSL Toolkit
(www.openssl.org),
Printed in Germany | © 09.17 Siemens AG cryptographic soft-
ware written by Eric
E-Mail: [email protected] Young
Tel: +49 180 524 70 00 ([email protected])
and software devel-
oped by Bodo
Moeller.

You might also like