UV DIVIDER VALVES
SERIES "B"
A PENTAIR COMPANY
SPECIFICATIONS:
Max. Operating Seal Lube Lube Indicator Mounting Screw Tie Rod
Pressure Material Inlet Outlets Ports Torque Nut Torque
3500 PSI Nitrile 1/4-18 NPSF 1/8-27 NPSF 1/8-27 NPSF 80-100 in.-lbs. 80-100 in.-lbs.
These divider valves are a component must be plugged. Use 68645 pipe plug.
part of a single line, progressive An 882000 By-Pass Block can be
lubrication system and can be used for used on any position on the base plate,
dispensing oil or grease. UV valves as long as there are at least three other
and baseplate segments are supplied working divider valves on the
with nitrile seals, however fluorocarbon baseplate. The bypass block allows
elastomer (Viton) seals are available. the addition or deletion of lubrication
Refer to the Modular Lube Planning points without disturbing existing piping.
Manual for system design information Both baseplate outlets under the
and an in-depth explaination of bypass block must be plugged.
operation. An in-line filter should be The valve blocks and bypass blocks
installed between the pump and divider are fastened to a baseplate mounted on
valves. Check valves should be the machine to be lubricated. The
installed at the inlets of all bearing baseplate contains the divider valve's
points. Refer to Service Manual Section inlet and outlet connections, interrelated
M50 Page 1 for check valve information. passageways, and built-in check
Valve blocks containing metering valves. All piping of lubricant to and
pistons discharge a predetermined from the divider valves is connected to
amount of lubricant with each cycle. the baseplate.
Description: Valve blocks will have either single or The baseplate consists of one inlet
UV Divider Valves are comprised of twin outlets and may be crossported block, three to eight intermediate blocks,
three to eight valve blocks fastened to a using Model 87944, 87945 or 87946 one end block, and a set of three tie
segmented base plate with O-ring seals Crossport Plate. Whenever a single rods and nuts. O-ring seals are
between the valve blocks and the outlet divider valve or crossport plate is installed into the intermediate and end
baseplate and the baseplate segments. used, the unused baseplate outlet(s) blocks. The valve block capacity of
UV VALVE BLOCKS
Divider Cycle indicator pin (right)
Single (1 outlet) Twin (2 outlet)
Valve Single Twin
Discharge/Outlet Discharge/Outlet
Stamping Single Twin
UV-5 882051 882052 - - .010 CU. IN. .005 CU. IN.
UV-10 882101 882102 - - .020 CU. IN. .010 CU. IN.
UV-15 882151 882152 - - .030 CU. IN. .015 CU. IN.
UV-20 882201 882202 882203 882204 .040 CU. IN. .020 CU. IN.
UV-25 882251 882252 882253 882254 .050 CU. IN. .025 CU. IN.
UV-30 882301 882302 882303 882304 .060 CU. IN. .030 CU. IN.
UV-35 882351 882352 882353 882354 .070 CU. IN. .035 CU. IN.
UV-40 882401 882402 882403 882404 .080 CU. IN. .040 CU. IN.
UV BASEPLATES **ALTERNATE THREAD CONFIGURATION
Inlet Intermediate End T ie
Outlets
B lock** B lo c k s * * B locks Rod Kit* Model No. Blocks Thread Size
2 to 6 87918 [3] 87919 87920 250290
2 to 8 87918 [4] 87919 87920 250291 87950 Intermediate 7/16 - 20 SAE
2 to 10 87918 [5] 87919 87920 250292 89951 Intermediate 1/8 - 28 BSPP
2 to 12 87918 [6] 87919 87920 250293 87952 Inlet 7/16 - 20 SAE
2 to 14 87918 [7] 87919 87920 250294 87953 Inlet 1/4 - 19 BSPP
2 to 16 87918 [8] 87919 87920 250295
* Kit consists of 3 rods and 3 nuts
One Lincoln Way
St. Louis, Missouri 63120-1578
Copyright 1999
Printed in U.S.A.
Section -M50
A PENTAIR COMPANY
(314) 679-4200
Page -14A
APRIL-99 FORM 422365
Page - 1
each baseplate is dependent upon the by disassembling the valve, reversing Operation:
number of intermediate blocks in the the piston in the valve bore, and The inlet passageway is connected to
baseplate assembly. There must be a reassembling by installing the indicator all piston chambers at all times with only
minimum of three working divider valves assembly on the left side of the valve. one piston free to move at any one time.
on each valve and baseplate assembly. With all pistons at the far right, lubricant
from the inlet flows against the right end
Cycle Indicator Pin Option: Assembly Instructions: of piston 1 (see illustration 1).
Optional cycle indicator pins provide 1. Screw three tie rods into inlet block Lubricant flow shifts piston 1 from
positive indication of system operation. until they bottom out in hole. right to left dispensing piston 1 output
The indicator pin is an extension of the 2. Check each intermediate block to through connecting passages to outlet 1.
piston in the valve block and will cycle in insure there are 9 O-rings securely Piston 1 shift directs flow against the
and out as the piston moves. installed in one face of each right side of piston 2 (see illustration 2).
Divider valves with cycle indicator intermediate block. Lubricant flow shifts piston 2 from
pins are supplied by the factory with the 3. Slide intermediate blocks onto the tie right to left dispensing piston 2 output
indicator assemblies on the right hand rods until the last intermediate block through valve ports of piston 1 and
side of the valve. If a left hand valve is is in place. Face of intermediate through outlet 2. Piston 2 shift directs
required, the valves may be converted block containing O-rings must be lubricant flow against the right side of
installed facing the inlet block end of piston 3 (See illustration 3).
the assembly. Lubricant flow shifts piston 3 from
4. Check end block to insure that there right to left dispensing piston 3 output
are 9 O-rings securely installed in through valve ports of piston 2 and
one face of the end block. through outlet 3. Piston 3 shift directs
5. Slide the end block, with O-ring face lubricant flow through connecting
adjacent to the last intermediate passage to the left side of piston 1 (See
block, over the tie rods. illustration 4).
6. Lay the baseplate assembly on a flat Lubricant flow against the left side of
surface. Install the three 1/4-28 lock piston begins the second half-cycle
nuts at the end block end of the which shifts pistons from left to right
250286 dispensing lubricant through outlets 4, 5
assembly. Torque the nuts to 80-100
Optional Mounting Bracket in. lbs. and 6 of the divider valve.
installation.
INLET INLET
OUTLET OUTLET OUTLET OUTLET
4 1 4 1
OUTLET OUTLET OUTLET OUTLET
2 5 2 5
OUTLET OUTLET OUTLET OUTLET
3 6 3 6
ILLUSTRATION 1 ILLUSTRATION 3
INLET INLET
OUTLET OUTLET OUTLET OUTLET
4 1 4 1
OUTLET OUTLET OUTLET OUTLET
2 5 2 5
OUTLET OUTLET OUTLET OUTLET
3 6 3 6
ILLUSTRATION 2 ILLUSTRATION 4
Page - 2
7 2
3
4
4
1 5
SECTION A-A
6
CYCLE INDICATOR ASS'Y.
DIVIDER VALVE ASSEMBLY (Only divider valves which have cycle
indicator pins installed)
1
SECTION B-B
B B
BY-PASS BLOCK ASS'Y
882000
SERVICE PARTS
ITEM PK G. PA R T
D ESC R IPTION
N O. QUA N . N O.
1 O-R i ng (N i tri l e) 20 250309
1A O-R i ng (Vi ton) 20 250310
2 Al ternate Outl et Pl ug Assembl y (N i tri l e) 1 250377
2A Al ternate Outl et Pl ug Assembl y (Vi ton) 1 250371
3 Socket H d. C ap Screw (1/4-28 X 1 1/4") 1 250333
4 O-R i ng (N i tri l e) 10 250318
4A O-R i ng (Vi ton) 10 250319
5 End Por t Pl ug Ass’y. (N i tri l e) 1 250378
BASE PLATE ASSEMBLY 5A
6
End Por t Pl ug Ass’y. (Vi ton)
C ycl e Indi cator Ass’y. (N i tri l e)
1
1
250208
250379
6A C ycl e Indi cator Ass’y. (Vi ton) 1 250207
7 O-R i ng (N i tri l e) 10 250372
7A O-R i ng (Vi ton) 10 250373
Page - 3
DIMENSIONS ACCESSORIES
4x ø9/32" Mounting Holes
CROSS PORTING PLATES
2 1/4"
3" 1 1/8"
13/16" 1/4-18
1 3/4" NPTF
9/64"
5/8" 1/2"
Max.
D es c r i p t i o n Mo d el Nu m b er
1/2"
1 13/64" Cross Por t Right 87944
Cross Por t Left 87945
Cross Por t Both 87946
59/64"
TYP 9/16"
1 1/8"
A B
DISC 1/8-27 NPTF
1/8-27 NPTF
Lube Outlet
ATMOSPHERIC INDICATORS
1/2" Max.
Model No Pressure Repl. Disk* Color
87934 1450 PSI P/N 69813-10 Yellow
87935 1750 PSI P/N 69813-12 Red
Ou t let s A B 87936 3250 PSI P/N 250312 Purple
87937 3700 PSI P/N 250313 Yellow/Natural
2 to 6 3.58 4.56 *Packaged in quantities of 10
9/16"
2 to 8 4.50 5.48 1 5/8" 1/8-27 NPTF
2 to 10 5.42 6.40 DISK
2 to 12 6.34 7.33
2 to 14 7.27 8.25
2 to 16 8.19 9.17
PIN INDICATORS
TYPICAL ACCESSORY INSTALLATION Model No Pressure Repl. Disk* Color
87930 1450 PSI P/N 69813-10 Yellow
87931 1750 PSI P/N 69813-12 Red
INDICATOR
87932 2650 PSI P/N 250311 Pink
87933 3250 PSI P/N 250312 Purple
*Packaged in quantities of 10
1/2" 2 1/4"
BY-PASS 1/8-27 NPTF
BLOCK
RESET INDICATORS
Model No Pressure Inlet
Crossport Plate
87938 500 PSI 1/8-27 NPTF
87939 1000 PSI 1/8-27 NPTF
87940 1500 PSI 1/8-27 NPTF
87941 2000 PSI 1/8-27 NPTF
87942 3000 PSI 1/8-27 NPTF
RETAIN THIS INFORMATION FOR FUTURE REFERENCE
When ordering replacement parts, list: Part Number, Description, Model Number, and Series Letter.
LINCOLN provides a Distributor Network that stocks equipment and replacement parts.
Page - 4
