Application Note AN-1107
IRS218(4,44) and IR218(4,44) Comparison
By Jason Nguyen, Min Fang, David New
Table of Contents
Page
Introduction ..........................................................................................1
Block Diagrams ....................................................................................2
Electrical Characteristic Differences.....................................................3
Figures .................................................................................................4
Summary..............................................................................................6
Introduction
The IRS218(4,44) are new HVIC products that replace the IR218(4,44) HVICs and are
pin-to-pin compatible with their corresponding predecessor. In many cases, little or no
change is necessary to use the new product. This application note describes the various
differences between the IRS218(4,44) and the IR218(4,44) HVICs.
The IRS218(4,44) are high voltage, high speed power MOSFET and IGBT drivers with
independent high and low side referenced output channels. Proprietary HVIC and latch
immune CMOS technologies enable ruggedized monolithic construction. The logic input is
compatible with standard CMOS or LSTTL outputs, down to 3.3 V logic. The output
drivers feature a high pulse current buffer stage designed for minimum driver cross-
conduction. The floating channel can be used to drive an N-channel power MOSFET or
IGBT in the high side configuration which operates up to 600 V.
There are no functional changes between the IRS218(4,44) and the IR218(4,44), however
the IRS218(4,44) design has eliminated the input zener clamp diode.
www.irf.com AN-1107 1
Block Diagrams
The IRS2184 and the IR2184 share the same block diagram. The IRS21844 and the
IR21844 share the same block diagram. There are no functional changes between
corresponding part numbers.
www.irf.com AN-1107 2
Electrical Characteristic Differences
All measurement conditions remain unchanged unless noted. Parameters not
mentioned in this document have not changed.
Absolute Maximum Ratings
Parameter IR218(4, 44) IRS218(4,44)
Symbol Definition min max min max Units
VB High side floating absolute voltage -0.3 625 -0.3 620 (Note1)
VS High side floating supply offset voltage VB - 25 VB + 0.3 VB - 20 VB + 0.3
VCC Low side fixed supply voltage -0.3 25 -0.3 20 (Note1) V
VIN Logic input voltage VSS - 0.3 VSS + 10 VSS - 0.3 VCC + 0.3
VSS Logic ground (21844 only) VCC - 25 VCC + 0.3 VCC - 20 VCC + 0.3
Note1: In IRS218(4,44), all supplies are fully tested at 25 V and an internal 20 V clamp
exists for each supply. The 20 V, internal clamp improves the IC survivability against
supply transient spikes but at the same time reduces the absolute maximum rating to
20 V.
In the IRS218(4,44), the input pins are no longer internally clamped with 5.2 V zener
diodes, therefore the maximum absolute rating for VIN is increased to VCC+0.3 V. In
IR218(4,44) applications where the 5.2 V clamp is used to protect the microcontroller
output, an external clamp is needed when the IR218(4,44) is replaced by the
IRS218(4,44).
Recommended Operating Conditions
Parameter IR218(4,44) IRS218(4,44)
Symbol Definition min max min max Units
VIN Logic input voltage VSS - 0.3 VSS + 5 VSS - 0.3 VCC V
In the IRS218(4,44), the input pins are no longer internally clamped with 5.2 V zener
diodes, therefore the recommended operating condition for VIN is increased to VCC.
Dynamic Electrical Characteristics
There are no changes in the Dynamic Electrical Characteristics.
www.irf.com AN-1107 3
Static Electrical Characteristics
Parameter IR218(4,44) IRS218(4,44)
Symbol Definition min typ max min typ max Units
VIH Logic "1" input voltage (VCC = 10 V to 20 V) 2.7 - - 2.5 - -
VIL Logic "0" input voltage (VCC = 10 V to 20 V) - - 0.8 - - 0.8
VSD,TH+ SD input positive going threshold 2.9 - - 2.5 - -
VSD,TH- SD input negative going threshold - - 0.8 - - 0.8 V
- - 1.2 - - 1.2
VOH High level output voltage, VBIAS - VO
Io = 0 mA Io = 0 mA
- - 0.1 - - 0.2
VOL Low level output voltage, VO
Io = 0 mA Io = 20 mA
With the IRS218(4,44),
1. The VIH and VSD, TH+ are reduced to 2.5 V for better 3.3 V logic compatibility.
2. The VOL is tested using a new standardized test condition of Io= 20 mA.
Figures
This figures shown in this section compare figures shown in the IR218(4,44) (left
column) and IRS218(4,44) (right column) datasheets. Illustrations that have not
changed between the two datasheets have not been included in this section.
IR218(4,44) IR218(4,44)
www.irf.com AN-1107 4
www.irf.com AN-1107 5
Summary
As shown by this document, the IRS218(4,44) and the IR218(4,44) are very similar
except that the IRS218(4,44) does not have the input Zener clamp.
www.irf.com AN-1107 6
