C21 Herd Management
DairyPlan C21 5.2 Introduction Manual
4448-3419-009
Edition May 2009
1 Farm Technologies / WestfaliaSurge
C21 Herd Management
2 Farm Technologies / WestfaliaSurge
C21 Herd Management
Page Topic
No.
4. Cow Entry
5. Culling Cows
7. Responder Number Entry
8. Group Numbering
10. Service Sire Details
11. Feed Amount Entry
12. Calving Entry
14. Service Entry
15. Dry-Off Entry
16. Milk Withdrawal
17. Reproduction Overview
18. ResCounter II
20. Status Code Overview
21. Cow Selection (Automated Gates only)
22. DPSingle
23. Reports
26. Milk Meter Performance Analysis
27. Re-Start Feeding
28. Data Backup
29. Software Security
3 Farm Technologies / WestfaliaSurge
C21 Herd Management
Cow Entry
This is where you enter your cows onto DairyPlan when you first start This is also where you
enter newly purchased animals in future . Alternatively if you use NMR you can get use a
DataStream disk to enter all the animal information automatically
3
4
Enter the animals line number
(freeze brand no.) For Metatron 12
systems the maximum number of
digits you can enter is 4. Enter as
much of the basic details such as
lactation no., calving dates as you
can. The Responder Number is for
Parlour Auto Identification systems
only. When you have finished
entering details press OK. You can
then enter the next cows details
4 Farm Technologies / WestfaliaSurge
C21 Herd Management
Culling Animals
There are two main options when Culling an animal in DairyPlan. You can completely remove
an animal so that there is no record left or you can Cull an animal but still keep her record for
future use i.e. in future you can look at the Dam’s records
Note : DairyPlan has a limit as to how many cows it can store .The standard is 500 cows.
When you Cull an animal but Save her records this Cull animal still counts as one animal. If in
future you find the number of animals in DairyPlan is approaching the Herd limit then you can
either Delete these Cull animals completely or you can purchase a DairyPlan Module to take
you up to the next Herd size . The Herd Size options are 500,1000,3000
Choose
1
an option
2 3
Enter the Left Herd Date - if you have
DPCert then enter 0 for a Sold animal
& 2 for a Dead animal (in DPCert you
can then enter extra details as to why
the animal was culled) . Otherwise
make up your own reasons e.g. 3 for
Mastitis ,4 for Bad feet etc.
5 Farm Technologies / WestfaliaSurge
C21 Herd Management
Culling Animals
Enter cow numbers to Cull.
6 Tip: If you wish to select a number of
animals in one step (assuming they
are culled on the same date & for the
same reason) then type the number of
the cow followed by a space and then
the next cow number e.g. 8 12 23
Now press this box to Cull 7
6 Farm Technologies / WestfaliaSurge
C21 Herd Management
Entering Responder
numbers
This section if for installations using Automatic Cow Identification whether it’s for Parlour ID,
Out of Parlour Feeders or Auto Selection Systems.
Enter the Responder number
of this cow in the box . For new
systems enter the last 8 digits
of the responder
7 Farm Technologies / WestfaliaSurge
C21 Herd Management
Changing Group numbers
If you group your cows in different buildings/lots you may want to keep a record in DairyPlan.
Alternatively if you intend using the Automatic Feed to Yield program then even though the
cows may be in one physical group , on the computer you may group them according to for
example stage of lactation, milk yield etc. for feeding purposes
8 Farm Technologies / WestfaliaSurge
C21 Herd Management
Changing Group numbers
Enter the group number here. You
5 can enter any group number from 1 to
99. After pressing the Enter key you
can then enter the group number for
the next cow
To return to the Main Menu press the
M button (6) & select DPMenue (7)
9 Farm Technologies / WestfaliaSurge
C21 Herd Management
Entering Sires
Enter the details of the Sires you currently use for breeding. If you wish to extra information
such as straws in stock then select option 5 shown below
2 3
6
5
Enter straws in stock & their location
10 Farm Technologies / WestfaliaSurge
C21 Herd Management
Entering Feed
Amounts
Enter here the feed amounts you wish each cow to receive per day whether this amount is to
be fed in Parlour or in the Out of Parlour Feed Stations
1
2
Enter the 24hour feed . If this is for In Parlour
Feeding then the feed amount will be divided by the
number of times you milk per day .
11 Farm Technologies / WestfaliaSurge
C21 Herd Management
Entering Calving
Details
1
2
3 Enter the 4
cow no. then
press the
RETURN key
on your
keyboard
12 Farm Technologies / WestfaliaSurge
C21 Herd Management
Entering Calving
Details
Enter Calving date &
other details if you
wish. In the comment
section you can for
example enter
whether it was an
assisted calving
6 In the case of twins
toggle between them
using these buttons
Enter the number of heifer/bull calves
followed by their registration no.
Tick the box if the calf is to be kept on the
farm as part of milk herd replacement stock .
Also give the calf a number, one that isn’t
currently used by any milking cows. The
number of the heifer can be altered when she
enters the Milk herd
Press OK to complete
13 Farm Technologies / WestfaliaSurge
C21 Herd Management
Entering Service
Details
3 Enter the cow no. 4
then press the
RETURN key on
your keyboard
5.Enter Service Date
6. Press “Sires” box to
get a list of Sires that
you are currently using
7. Press “OK Save” to
complete
14 Farm Technologies / WestfaliaSurge
C21 Herd Management
Entering Drying-Off Details
3 Enter the cow no. 4
then press the
RETURN key on
your keyboard
5.Enter Dry-Off Date
6. Any comment such
as drug used (DPCert
users enter in DPCert
instead
7. Press “OK Save” to
complete
15 Farm Technologies / WestfaliaSurge
C21 Herd Management
Milk Withdrawal
•Enter Isolation Code 1
Time of day withdrawal to Finish
Date withdrawal to Finish
Time of day withdrawal to START
Date withdrawal to START
16 Farm Technologies / WestfaliaSurge
C21 Herd Management
Reproduction Overview
The Reproduction Overview is an electronic version of the Calendar board . It shows at a
glance the reproduction situation in the herd
Tips:
ResCounter Tips:
1. The no. of dots in each
box is the no. of times this 1. Fast flashing Yellow box
animal has been Served indicates a full activity
2. Move mouse onto cow alarm in the animal’s
number to get extra details expected heat cycle
3. Double click on an animal 2. Slow flashing Yellow box
to bring up the next logical indicates a full activity
DPVet event entry box alarm
4. A yellow message beneath 3. Slow flashing white box
means that not all the cows indicates a “suspicious”
in this herd could be fitted activity reading
onto this screen
17 Farm Technologies / WestfaliaSurge
C21 Herd Management
ResCounter II
Cows with High Activity can be checked by either viewing a Report List or by viewing a
Graph
Report Viewing: You can use either a Report showing cows active in the last 12 or 24
hours. The example below shows a Report List with cows active in the last 24 hours
Optional 12 Hour
Activity List
1
•The number of pluses indicates the level of activity.
•The more readings shown the longer the period of
high activity
Days since last but one high activity
Days since last high activity
Cows with high activity in last 24 hours
18 Farm Technologies / WestfaliaSurge
C21 Herd Management
ResCounter II
Cows with High Activity can alternatively be checked by viewing a Graph
Press these buttons to view
next or previous cow with
High Activity
Days from
today
1. This cow shows a recent High Activity Time of peak activity can
2. Previous activity approximately 21 be checked to determine
days and 42 days helps confirm that optimum insemination time
the cow is in HEAT
19 Farm Technologies / WestfaliaSurge
C21 Herd Management
Status Code Overview
Each animal is assigned a status code indicating its stage of lactation.The status codes also
form the basis for many analyses in DairyPlan.The status of the cow determines whether it is
being fed, milked or checked for being in heat.
20 Farm Technologies / WestfaliaSurge
C21 Herd Management
Cow Selection
(Automatic selection gates only)
If you have an Automatic Selection system then you can enter the date that you wish to select
a cow . For example if you have a vet visit in 10 days time you can program Dairyplan to select
any cows on that particular day. Off course you can also select an animal during milking using
the Metatron terminal . See Metatron Parlour Information sheet for details . The example
shown shows only a limited part of the Selection system possibilities. Please contact your
Dealer/technician for further information
1
2
4 3
Enter the Selection date
here . As in all Dairyplan
programs if you enter for
example +7 then it will
add 7 days onto today’s
date
Ensure that a Y for yes is
entered here for each
animal to be selected
21 Farm Technologies / WestfaliaSurge
C21 Herd Management
DPSingle
DPSingle allows you to view information of individual animals in more detail e.g. Lactation
records ,Vet history, Lactation Graphs etc.
Enter animal no.
and press OK
1
Lactation records,Milk Veterinary
Measurements,Ancestry etc history
Lactation Graphs
22 Farm Technologies / WestfaliaSurge
C21 Herd Management
DairyPlan Reports
DairyPlan has a large number of reports to choose from . Below are some of the most useful
as far as Herd Management is concerned. All reports can be changed to suit an individual
farms requirements or new reports created
This is the Milk Production
report. It is in cow number
order
Tip: If you double click on a
cow number DPSingle will
appear for that animal
23 Farm Technologies / WestfaliaSurge
C21 Herd Management
DairyPlan Reports
This report shows cows
that are down in Milk or that
have high Conductivity
The + sign show she has increased milk yield or
conductivity & - sign the opposite. The more + or
– signs the more significant the alarm .The report
shows the last 3 milkings for each alarm animal
so that you can see the trend
24 Farm Technologies / WestfaliaSurge
C21 Herd Management
DairyPlan Reports
1
2
This is the ‘Cows Due to
Calve’ report. It is in order
of Due date.
This is the ‘Dry Cow List’. It
is in order of Due date.
25 Farm Technologies / WestfaliaSurge
C21 Herd Management
Milk Meter Performance
Analysis
This report enables you to check the performance of each milk meter & also cross check milk
meter milk totals with Bulk Tank milk collection amounts. Note: Divide the Milk Meter Total(kg)
by 1.03 to compare with Milk Collection Tanker which is measured in Litres
No. of milkings at
each milk meter
Auto ID percentage
success
Total milk through
each milk meter. If
one meter is
consistently showing
more or less milk it
may indicate a fault
with that meter
This part of the report
shows the Total Milk
produced for each of the
last 8 milkings as well as
the number of cows milked
26 Farm Technologies / WestfaliaSurge
C21 Herd Management
Re-Start Feeding
If for any reason you find that the In Parlour Feeding does not operate or the feed that you
have entered today hasn’t yet taken effect try the following steps
Double click on the
DPProcess icon
1
Select the 5
CLOSE button
4
Restarting the Feed
system only takes a
few seconds after
which this screen
disappears
27 Farm Technologies / WestfaliaSurge
C21 Herd Management
Data Back-up – using Floppy disk
Backing up DairyPlan data should be carried out as often as possible,ideally once a week .You
can backup onto floppy disks (which these days aren’t as reliable) or USB memory stick
1
2
5
3
If you are backing up onto
floppy disk click on Diskette
28 Farm Technologies / WestfaliaSurge
C21 Herd Management
Data Back-up – using Memory Stick
1
2
8
3
If you are backing up onto
Memory Stick or other device
click on the Browse key to
locate the device
5
Highlight backup device
Enter file name e.g. 7
DPBackup.dpb 6
& then press the OPEN key twice
NOTE : For future backups carry out steps 1,2,3,8 only .This
is because it remembers where you’ve backed previously
29 Farm Technologies / WestfaliaSurge
C21 Herd Management
Software Security
A screen similar to that shown below appears each time you access information in DairyPlan.
The information shown should be forwarded by the installer to WestfaliaSurge head office.
Once this information is processed you will be contacted & given a Software Security key 2 no.
You should enter this number in the box shown & then press the OK button. If the number is
correct then this Security screen won’t appear again.
Enter Key 2 no. here
30 Farm Technologies / WestfaliaSurge
