386

Vorsprung durch Technik www.audi.co.uk Service Training

6-speed twin-clutch gearbox 02E (S tronic)

Self-Study Programme 386

All rights reserved. Technical

specifications subject to
change without notice.

Copyright
AUDI AG
I/VK-35
[email protected]
Fax +49-841/89-36367

AUDI AG
D-85045 Ingolstadt
Technical status: 10/06

Printed in Germany
A06.5S00.31.20
Table of contents

Introduction

A new generation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Gearbox concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Gearbox periphery

Gearshift mechanisms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Shift lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Ignition key withdrawal lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Gearbox subassemblies

Overview – 02E gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Twin clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Design features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Oil supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dynamic pressure equalisation in the clutches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Clutch control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Hydraulic clutch control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Clutch cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Clutch functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Overload protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Creep control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Microslip control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Clutch control adaptation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Safety shut-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Manual gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Selector mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Synchromesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Hydraulic control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
gearshift sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Parking lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
All-wheel drive - power distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Bevel box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Oil supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Hydraulic diagram of 02E gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Gearbox control unit

Gearbox control unit – mechatronic module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Electro-hydraulic control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Description of the valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Electronic module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Mechatronic control unit J743 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Function diagram of the Audi A3 (8P) and Audi TT (8J) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Function diagram of the Audi TT (8N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
CAN information exchange in the Audi A3 (8P) Audi TT (8J) . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
CAN information exchange in the Audi TT (8N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Gearbox oil (ATF) temperature sender G93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Temperature sensor in control unit G510. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Multi-plate clutch oil temperature sender G509 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Gearbox input speed sender G182 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Drive shaft 1 speed sender G501 (G502) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Gearbox output speed sender -1- (2) G195 (G196) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Automatic gearbox hydraulic pressure sender -1- (2) G193 (G194) . . . . . . . . . . . . . . . . . . . . . . 71
Gear selector travel sensor 1 (2, 3, 4) G487 (G488, G489, G490) . . . . . . . . . . . . . . . . . . . . . . . . 72
Selector lever sensor system E313 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
tiptronic switch F189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Gearbox functions

tiptronic steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

"Freeing vehicle by rocking back and forth" and drive-away in 2nd gear. . . . . 80
Launch Control Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
S - sport program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Downshifting with short intermediate throttle application
between gearshifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Software Shift Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Starter inhibitor/starter control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Activation of the reversing lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Selector lever position, gear and fault indication . . . . . . . . . . . . . . . . . . . . . . . . . 84
Kick-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSP291, p. 62 . . XX
Emergency (limp-home) program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Index

Dear reader, to help you to find information, we have compiled for you an
index on the last page.
 Introduction

The S tronic 02E twin-clutch gearbox is also known as the Direct Shift Gearbox (DSG) 02E.

Given that Audi uses the name "-tronic" for its automatic gearboxes (tiptronic, multitronic),
the twin-clutch gearbox 02E has been named "S tronic" in keeping with
the Audi nomenclature system.

Is the S tronic a manual gearbox or an automatic gearbox?

It is both. The S tronic is an automatic sport gearbox with the emphasis on "Sport".
The technical basis of the S tronic is a 6-speed-manual gearbox which, as a special feature, has two clutches
(twin clutch).

Clutch control and gearshifts are performed by an electro-hydraulic control.

A twin multi-plate clutch and an intelligent electro-hydraulic control are used allowing two gears to be
selected simultaneously.
While driving, one gear is engaged and the matching gear is preselected.
During gearshifts, the clutch engaging the active gear opens while the other clutch of the preselected gear
closes. This is done under load and so quickly that power flow is virtually continuous.

4
 386_003

What are the customer benefits of the S tronic gearbox?

The S tronic 6-speed twin-clutch gearbox is more dynamic than a conventional manual gearbox, because
it allows fast gear-shifting without any interruption in tractive power while affording the comfort of an
automatic gearbox.

In addition to the overtly sporty driving dynamics, the S tronic gearbox is highly efficient. This gives it an
advantage over the conventional manual gearbox with regard to fuel economy.

The self-study programme teaches the design and function of new vehicle models,
new automotive components or new technologies. Reference Note

The Self-Study Programme is not a Repair Manual!

The values given are intended as a guideline only and refer
to the software version valid at the time of publication of the SSP.

For maintenance and repair work, always refer to the current technical literature.

5
 Introduction

A new generation

Back in 1940 …

All efforts at automating clutch and gear shift Franke‘s objective was to eliminate the interruption
operations were initially geared towards simplifying in tractive power flow when shifting gear, which
the gear-shifting in step-up gearboxes for the was a handicap in commercial vehicles (e.g. off-
benefit of inexperienced drivers. road vehicles, tractors) in particular.

However, Rudolf Franke did not have this in mind The concept of "tractive power flow interrruption
when, in 1940, he applied for a patent on his four during gear shifts" was, apparently, mentioned for
speed twin-clutch gearbox. the first time in Franke's patent application.
Though his design included nearly all the features
of modern designs, it did not get off the drawing
board.

386_004

Drawing from the patent specification of Rudolf Franke dating from 1940

… 30 years later …

About 30 years after Franke's patent was registered, All attempts to use this twin-clutch gearbox type
Porsche readopted the idea and developed the first in production vehicles failed, because the control
twin-clutch gearbox for its 962C race car, which was system was too difficult to implement and
also used by Audi in the short version of its Rallye electronics, at the time, were not advanced
quattro. enough to meet the attendant demands.
In both cases, the design proved a success.
So-called "dry clutches" were used.

6
… The year 2003.

However, the twin-clutch gearbox concept was The 02E twin-clutch gearbox was developed by
by no meansdead and forgotten. The dream of Volkswagen in conjunction with well-known
continous tractive power flow during gear-shifting systems suppliers Borg Warner (clutch, hydraulics)
still lived on. and Temic (electronics).

Today's cutting-edge technology has made it

possible to develop and put into production a twin- The twin-clutch gearbox combines the key
clutch gearbox which not only meets the original advantages of the manual gearbox with those
objective and today's requirements, but also sets of a modern automatic gearbox.
new standards.

386_005

Characteristics of the manual gearbox:

+ sportiness/driving dynamics Characteristics of the twin-clutch gearbox:

+ efficiency
– comfort Superb driving dynamics thanks to lightning-fast
– interruption in tractive power and jolt-free gearshifts
without any interruption in tractive power

An excellent balance of comfort, sportiness and

efficiency
Characteristics of the automatic gearbox:

+ high level of comfort

+ no interruption in tractive power
– sportiness/driving dynamics
– efficiency

7
 Introduction

Gearbox concept

A twin-clutch gearbox basically consists of two full While driving, only one part-gearbox is engaged by
synchromesh speed change gearboxes connected clutch K1 or K2 .
in parallel (part-gearbox 1 and part-gearbox 2).
The twin-clutch gearbox has two input shafts and
Each part-gearbox has is own clutch: two output shafts.

– Part-gearbox 1 K1
– Part-gearbox 2 K2

Part-gearbox 1 shifts odd gears 1, 3 and 5,

as well as reverse.
Part-gearbox 2 shifts even gears 2, 4 and 6.

Final drive and

differential Engine torque

386_006

Part-gearbox 1

Part-gearbox 2

Fig. 386_006 shows a schematic diagram of a twin-

clutch gearbox. It illustrates the functional principle
in simple terms.

To make the twin-clutch gearbox 02E as compact

and lightweight as possible, the design deviates to
a certain extent from this schematic diagram; refer
to Fig. 386_007 on page 16.

8
 Specifications

6-speed twin-clutch gearbox 02E (S tronic)

Designations Manufacturer: DQ250 6F / DQ250 6Q

Service: 02E direct shift gearbox "DSG"
02E S tronic twin-clutch gearbox

Development/manufacturer Volkswagen AG

Gearbox type Electro-hydraulically controlled twin-clutch gearbox,

full synchromesh 6-speed speed change gearbox

Control Mechatronics - integrate, as a unit, the hydraulic control

unit, the electronic control unit and, to a great extent,
the sensors and actuators.
Sport program and "tiptronic" shift program for manual
gear-shifting (optionally available with tiptronic steering
wheel)

Twin clutch Two electro-hydraulically controlled, oil-cooled multi-plate

clutches

Torque capacity max. 350 Nm (depending on type)

Oil fill quantity, specification and refer to current service literature

ratios

Weight Front-wheel drive variant, approx. 94 kg

quattro variant, approx. 109 kg

Oil cleaner
Oil cooler
Selector lever cable

Manual gearbox

Parking lock

Oil pump

Bevel box (quattro)

386_003

Twin clutch

Mechatronics
Reverse shaft

9
 Gearbox periphery

Gearshift mechanisms

At first glance, vehicles with S tronic gearbox have a Gearshift mechanism,

similar gearshift mechanism to previous automatic Audi A3 (8P) and Audi TT (8J)
gearboxes.

The fundamental differences are:

– There is no manual selector valve in the hydraulic

control unit.
– There is no multi-function switch in or on the
gearbox.
– The selector lever cable on the gearbox actuates
the parking lock only (mechanical system).

S tronic gearshift mechanism

The S tronic gearshift mechanism incorporates

386_081
an electronic module – the selector lever sensor
Selector lever sensor system E313
system E313.
The E313 comprises sensors and a control unit
mounted on a board; refer to page 74.

The selector lever sensor system E313

… determines all selector lever positions for the

gearbox control unit,
… controls the LEDs on the selector gate cover
or display unit,
… controls the shift lock solenoid N110, Gearshift mechanism,
… communicates all information to the Audi TT (8N)
mechatronic control unit J743 by powertrain
CAN bus.

There is no mechanical connection between the

Shield plate
gearshift mechanism and the mechatronics. This
is also known as a "shift by wire" system. As
mentioned previously, the selector lever cable on
the gearbox serves only to actuate the parking lock.

There are two different shift lock and ignition key Locking bolt of the N110
withdrawal lock systems:

1. Shift lock and ignition key withdrawal lock

conventional by means of locking cable –
as used in the Audi TT (8N)

2. Shift lock and ignition key withdrawal lock

without locking cable and with electrically
actuated ignition key withdrawal lock –
as used in the Audi A3 (8P), Audi TT (8J)

386_113
View from the left

10
The selector gate covers in the Audi A3 and in the Audi A3 - old specification
Audi TT come in two versions, depending on model:
Selector lever display
Old: Selector gate cover with integrated illumination L101
for selector lever position indicator light

New: Selector sleeve and separate selector lever

position indicator unit

The selector lever position indicator LEDs are

activated directly by the selector lever sensor
system E313; refer to function diagram below.

386_104

Audi A3 - new specification

Selector lever
position indicator unit Y26
(also known as L101)

386_122

386_119

386_103

The illustrations show the variants of the selector

gate covers for the Audi A3.
The selector gate covers for the Audi TT differ in
Shift lock solenoid N110 respect of their design, but otherwise they are
absolutely identical.

Reference
For information on the selector lever
position and gear indicator in the dash
panel insert, refer to page 84.

386_114

View from the right

11
 Gearbox periphery

Shift lock
Audi A3 (8P), Audi TT (8J)
Basically, a distinction is made between the P/N lock Emergency release
mechanism
while driving or at ignition 'on', and locking of the
selector lever in the "P" position after removal of the
ignition key (P-lock).
Park ("P") pawl
The kinematics of the selector lever and the
shift lock solenoid allow locking when N110
is energised (position "P") and deenergised
(position "N").

This functional principle is such that the selector

lever stays locked in position "P" in the event of a
malfunction or power failure (e.g. flat battery); Shift lock
refer to Fig. 386_094. solenoid N110

There is an emergency releasemechanism for

moving (e.g. towing) the vehicle in these situations.

Locking bolt
of the N110
386_093

Pawl for "N"

Selector lever position "P" locked

Solenoid N110 is deenergised and the locking

bolt engages the park (P) pawl due to the spring
Locking bolt pressure.
The selector lever is locked.

Actuating mechanism
Emergency release
Emergency release
The emergency release mechanism is accessible
after removing the gearshift console cover (refer
to the operating instructions).
When the emergency release is actuated, the
Emergency release
mechanism
Spring lokking bolt of N110 is pushed out of the park
386_094
pawl against the pressure of the spring.
The selector lever can now be moved out of
position "P".
Selector lever position "P" unlocked

Solenoid N110 is energised by the selector lever

sensor system E313 and the locking bolt is drawn
out of the park pawl against the pressure of the
spring.
The shift lock is disengaged.

386_095

12
Selector lever position "N" locked

If the selector lever is in position "N" for longer than

2 seconds at "ignition ON", then N110 is energised
by the selector lever sensor system E313.
The lokking bolt is moved into the neutral "N" pawl
against the pressure of the spring.
The N lock is not activated when the vehicle is
travelling faster than approx. 5 kph.

386_088

Selector lever position "N" unlocked

N110 is deenergised when the brake is operated or

at "ignition OFF". The locking bolt is drawn out of
the neutral "N" pawl by the pressure of the spring.

386_089

Shift lock
Audi TT (8N)

In the Audi TT (8N) the park "P" lock is actuated

by the steering lock by means of a cable pull
(locking cable) – refer to Workshop Manual.

The P/N lock is designed in such a way that the

shift lock solenoid N110 only engages the selector
lever in positions "P" and "N" when it is energised.

Ignition key withdrawal lock

Audi TT (8N)

In the Audi TT (8N) the ignition key withdrawal lock

is actuated by the gearshift mechanism by means
of a cable pull (locking cable) connected to the
steering lock – refer to Workshop Manual.

386_096

13
 Gearbox periphery

Ignition key withdrawal lock

Audi A3 (8P), Audi TT (8J)
The ignition key withdrawal lock is operated Firstly, by means of microswitch F319.
electro-mechanically by means of the ignition key F319 is integrated in the gearshift mechanism.
withdrawal lock solenoid N376. It does not allow the It supplies the information "selector lever locked in P"
ignition key to be turned anticlockwise to the end to the selector lever sensor system E313 and from E313
position (withdrawal position) if the selector lever to J527 via a discrete line (refer to function diagram).
is not in the "P" position.
N376 is activated by the steering column electronics Secondly, the selector lever positions are
control unit J527. Before J527 can do this, it must communicated to J527 by CAN information exchange.
receive the information "selector lever in position P". Information path: E313 (powertrain CAN bus) > J743
For safety reasons and for the purpose of (powertrain CAN bus) > J533 (convenience CAN bus) >
diagnostics, this information is transmitted J527.
to J527 in two ways.
The CAN information is used for verifying the
plausibility of the signal from F319 and as a substitute
signal in case of malfunctioning of F319.

Ignition key withdrawal lock

solenoid N376

Steering column electronics 386_097

control unit J527 386_098

Selector lever locked

in position "P" switch F319

Shift lock solenoid N110

Selector lever sensor system

with tiptronic switch F189

386_099

Switch F319 is configured as an NC contact. Switch F319 is closed in selector lever positions "R",
It is actuated when the gearshift knob lock button is "N", "D", "S" and tiptronic (and in "P" with the lock
released in selector lever position "P" ("open" circuit button pressed).
state).

14
Ignition key withdrawal lock function

P signal

386_100

A)
When the selector lever is not in the "P" (Park) Note
position, the ignition key withdrawal lock
solenoid N376 is energised by J527. The function of the selector lock in
The locking bolt of N376 is pressed into the position "P" switch F319 can be checked
steering lock against the pressure of the spring. in steering column electronics control
The ignition lock cannot be turned to the unit J527 (address word 16), in data
withdrawal position as long as the N376 is block 005, 1st display value.
energised (lokking bolt retracted). The ignition
key cannot be removed.

B)
The solenoid is not energised when the ignition Note
is OFF and the selector lever is in the "P" position J527 applies an electrical current to
(lock button on selector lever not pressed). solenoid N376 as long as the selector
The locking bolt is retracted by the spring in the lever is out of the "Park" position after
N376. The key can be turned to the withdrawal ignition OFF.
position and removed. The battery can become discharged if the
vehicle is parked for a lengthy period of
time with the selector lever out of the "P"
position.

15
 Gearbox subassemblies

Overview - 02E gearbox

To illustrate the individual shafts more clearly, output shafts 1 + 2 and the reverse shaft are not shown in their
actual positions but arranged in such a way that all the shafts lie in the same plane.

Dual-mass flywheel Final drive

Spur gear Input shaft 2
1.
2.
K1 3. Output shaft 1
4.
K2

Pump shaft

Oil pump

6. Output shaft 2
5.
Input shaft 1

Twin clutch

386_007
R. Reverse shaft

Engine torque is transmitted through a dual-mass The two output shafts transmit engine torque in
flywheel to the twin clutch input hub by means of a different ratios to the final drive spur gear, and from
stub shaft spline. here to the differential and (in models with quattro
Depending on which gear is engaged, the twin drive) the bevel box (also refer to Fig. 386_009).
clutch transmits the torque either to input shaft 1 or
2 and from this shaft to output shaft 1 or 2.
The coaxial arrangement of the input shafts and the
mixed distribution of odd and even gears to the two
output shafts allow a very compact design and keep
weight to a minimum.

16
Position of the shafts in the gearbox - side-on view

Output shaft 1

Mechatronics Parking lock

386_008

Input shafts 1+2

Spur gear
Reverse shaft

Output shaft 2

View with final drive and bevel box

(bevel box for quattro four-wheel drive only)

Mechatronics Shift fork

Twin clutch Angle drive

Flange shaft for

prop shaft

Differential

Spur gear
Oil pump 386_009

17
 Gearbox subassemblies

Twin clutch
Outer plate carrier K1

Driving disc
Clutch K1

Clutch K2
Inner plate carrier K1

Outer plate carrier K2

Main hub
Input shaft 2
Inner plate carrier K2

Oil pump
drive shaft

Input hub
with driving disc Input shaft 1

Rectangular rings/
rotating ports

386_010

Power flow
Note
Engine torque is transmitted via a stub shaft spline The twin clutch must not be dismantled.
from the dual-mass flywheel to the twin clutch input If the driving disc or the retaining clip is
hub. removed, the plates of clutches K1 and K2 can
The input hub is welded to the driving disc. drop out of the clutch plate carriers. The steel
The driving disc is positively connected to plates and the lined plates of the clutches are
outer plate carrier K1, and transmits engine torque aligned and installed in pairs at the factory.
thus to the twin clutch. Outer plate carrier K1 and This ensures optimum torque uniformity during
outer plate carrier K2 are both welded to the main clutch engagement and counteracts drive-away
hub, so they are in positive engagement at all times. shudder.
The installation position of the clutch plates in
Engine torque is transmitted to the two clutches relation to one another is not marked. The clutch
at the respective outer plate carriers and, when plates cannot be reassembled in their original
clutch is positively engaged, to the appropriate state after the clutch has been dismantled or
inner plate carriers. fallen apart. Incorrect installation will provoke
Inner plate carrier K1 is connected to input shaft 1, drive-away shudder.
and inner plate carrier K2 is connected to input After replacement of the twin clutch or the
shaft 2. mechatronics and after updating the gearbox
control unit program, the clutch adaptation
values must be reset using the diagnostic tester.
For this purpose, the "Basic Setting" procedure
must be started under "Guided Functions"
and the described adaptation procedure
subsequently carried out.

18
 Piston K1

Pressure chamber K1

Pressure equalisation
chamber K1

Pressure chamber K2

386_013

Pressure equalisation Piston K2

chamber K2

Design features

Since clutch K1 serves as a starting clutch in Specifications of the twin clutch:

1st gear and in reverse (R), it is subjected to
greater loads than clutch K2. – Max. torque 350 Nm
The twin clutch has, therefore, been designed – Max. surface pressure 10 bar
in such a way that clutch K1 is disposed on the – Max. friction 70 kW
outside. As a result, it has the greater diameter – Max. cooling oil flow rate 20 l/min
and, therefore, is capable of transmitting a greater
amount of torque and a higher power output.
All the requirements are therefore met.

To keep to a minimum the sychronising masses

during gearshifts, the lined plates of both clutches
are assigned to the respective inner plate carriers.
The heavier steel clutch plates are assigned to the
outer plate carriers.

Dynamic pressure build-up in both clutches is

equalised, refer to page 21.

19
 Gearbox subassemblies

Oil supply
The illustration shows two
K1 different states:
In the upper half, clutch K1 is
Piston K1 shown positively engaged.
In the lower half, clutch K2 is
Clutch K1 positively engaged

shown positively engaged.

Pressure equalisation
chamber K1

Pressure chamber K1

Pressure oil supply,

clutch K1

Cooling oil supply

Main hub with

rotating port

Pressure chamber K2
Clutch K2 positively engaged

Piston K2

Pressure equalisation
chamber K2

K2
high 0

Oil pressure

386_014

Pressure oil is supplied to the clutches through the If K1 is positively engaged, the cooling oil flows
main hub by means of rotating ports. through the open K2 (without heating up) and
Rectangular rings provide a tight seal between the then to K1, where it does its work (lubricating
housing and the main hub. The oil flows along ducts and cooling) and is recirculated into the gearbox
in the main hub to the respective points. housing.

The clutches are continuously cooled and lubricated The clutch plate carriers are perforated, allowing
by a separate cooling oil system in accordance with the cooling oil to flow from the inside out to the
demand (refer to "Clutch cooling"). respective clutches. The shape of the lined plates
and the centrifugal force are conducive to through-
The cooling and lubricating oil is ducted through flow in the clutches. This allows the pressure of the
coaxial bores in the main hub to K2. cooling oil flow to be kept relatively low. The
The oil for the pressure equalisation chamber is quantity of cooling oil is decisive.
likewise extracted from this flow.

20
Dynamic pressure equalisation in the clutches

At high engine speeds, due to rotation, the oil is To ensure that clutches K1 and K2 open and closed
subjected to high centrifugal forces inside the in a defined fashion, dynamic pressure equalisation
clutch pressure chambers. takes place in the respective pressure equalisation
This causes the pressure inside the clutch pressure chambers (when engine speed is increased).
chamber to increase towards the largest radius.
This is known as "dynamic pressure build-up". This allows gearshifts to be regulated exactly, which
in turn considerably enhances shift comfort.
Dynamic pressure build-up is undesirable, because
it increases the surface pressure unduly and makes Leaks in the pressure equalisation chamber will
defined pressure increase and reduction inside the cause damage to the clutch and the synchronizer
pressure chamber more difficult to implement. due to uncontrolled positive engagement of the
clutch at high engine speeds.

Pressure equalisation chamber K1

Outer plate carrier K2 also Pressure chamber K1

serves as the baffle plate of K1

Baffle plate K2 Pressure chamber K2

Pressure equalisation chamber K2

Force exerted by the oil

due to centrifugal force

386_123

This is how it works:

The pistons are sprayed by oil on both sides. This is The pressure equalisation chambers are filled with
achieved by using additional oil chambers (pressure cooling oil under low pressure. The oil encased in
equalisation chambers) on the sides the pistons the pressure equalisation chamber is subjected
opposite the pressure chambers. to the same forces (dynamic pressure build-up) as
For this purpose, clutch K2 has a baffle plate which in the pressure chambers. The surface pressures in
represents the pressure equalisation chamber K2 the pressure chambers are thus equalised.
between clutch K2 and piston K2. In the case of
clutch K1, the outer plate carrier of clutch K2 serves,
additionally, as the baffle plate.

21
 Gearbox subassemblies

Clutch control

Encoder disc, input shaft 1

Encoder disc, input shaft 2

386_016

G509 G182 to mechatronics Encoder disc, output shaft 2

To control clutches K1 and K2, The following functions are relevant

the following information is processed: to the twin clutch:

– Engine speed – Drive-away

– Gearbox input speed from G182 – Power flow transition
(= clutch input speed) – Clutch cooling
– Speed of input shaft 1 from G501 – Clutch control at standstill (creep control)
(= clutch output speed K1 – Overload protection
= gearbox input speed of part-gearbox 1) – Safety shutdown
– Speed of input shaft 2 from G502 – Microslip control
(= clutch output speed K2 – Clutch adaptation
= gearbox input speed of part-gearbox 2)
– Engine torque
– Cooling oil outlet temperature from G509
(multi-plate clutch oil temperature sender)
– Brake pressure

22
Drive-away

When starting from a stop, the clutch is controlled When starting from a stop at a low throttle position
according to engine speed. Depending on the drive- (e.g. 60 %), engine speed is increased at a low level
away characteristic, the gearbox control unit up to the next clutch engagement point.
computes an engine nominal speed which is set When starting from a stop at a high throttle position
via the clutch torque. (e.g. 100 %), the engine speed is increased at a
The driver input as well as the torque curve of higher level up to the clutch engagement point.
the various engine variants define the drive-away
characteristic.

Throttle position
100 %
Engine nominal speed Throttle position

Throttle position
60 %
Engine speed

Gearbox input speed

Gearbox output speed

Engine speed

Engine speed

Time Time

Power flow transition (overlap)

The gearshift involves two functions:

Engine torque intervention
1. Engagement of gears in part-gearbox 1
and/or part-gearbox 2 by means of hydraulically
actuated shift forks.
K2
2. Power flow transition between part-gearbox 1
Torque

and part-gearbox 2 by means of clutches K1

Engaging Disengaging
and K2 clutch clutch
K1
The power flow transition (first to sixth gear) is
implemented by means of so-called overlapping
Time
shifting between clutches K1 and K2. This means
that, during the power flow transition, the power- Overlap/torque reception
transmitting clutch (K1 in this example) remains
capable of transmitting torque at a reduced
pressure until the engine torque is transmitted
to the engaging clutch (K2 in this example).

The gearshift is assisted by a temporary

reduction in engine torque during upshifts
(refer to illustration), or by a temporary increase
in engine torque during downshifts.

23
 Gearbox subassemblies

Hydraulic clutch control

Main pressure

N217

SPV

CCV

N218

Safety valve 2

N233 N371

to K1 G194
Safety valve 1
to K2

G193

N216
N88 N89 N90 N91
N215

Clutch valve 2
N92
Clutch valve 1

Multiplexer
Shift fork

high 0 386_058

Oil pressure

Control pressure

Note
A special feature of the 02E gearbox is the
The hydraulic diagram shows the valve
direct activation of clutches K1 and K2
positions when the engine is running
by electromagnetic pressure control valves.
and when the gearbox control unit is
deenergised.

24
Hydraulic control

Mechatronic control unit J743 calculates from the Senders G193 and G194 (hydraulic pressure
parameters on page 18 the nominal clutch pressure senders) monitor the clutch pressure (actual
and determines a corresponding control current for pressure) in the hydraulic control unit.
pressure control valve N215 or N216.
The actual clutch pressure is continuously
The clutch pressure, and hence the engine compared with the nominal clutch pressure
torque transmitted by the clutch, changes calculated by J743.
nearly proportionally to the control current. The actual and nominal pressures are checked
continuously for plausibility and a safety shutdown
is effected in case of critical deviations; refer to
page 28.

Clutch cooling

To avoid overheating of the clutches, the clutches are cooled by a separate oil flow.
The clutch cooling system is activated at the same time as the clutch is controlled.
The near-permanent microslip ensures that the clutches are continuously cooled and lubricated.
The cooling oil flow is shown overleaf on Fig. 386_021.

The mechatronic control unit J743 activates N218 depending on clutch state/cooling oil demand by applying
a defined electrical current, which in turn produces a proportionate control pressure. This control pressure
acts upon the piston of the clutch cooling valve (CCV). Depending on the control pressure, a corresponding
oil flow is branched off the system oil pressure and fed to the clutches. The maximum cooling output is
approx. 20 l/min at 2.0 bar.

The N218 has a falling current/pressure characteristic. This means that in case of failure of the N218, the
maximum cooling oil flow is set at all times and, therefore, the maximum possible cooling output is available.
Fig. 386_058 (adjacent) shows this state.

To keep power losses due to clutch cooling to a minimum, the cooling

oil flow is controlled according to the following driving conditions:

Driving condition State - clutch cooling Activation of N218

Drive-away Max. cooling output 0 mA

Creep control Max. cooling output 0 mA

Gearshift Max. cooling output 0 mA

Driving with microslip Reduced cooling output 575 mA*

Driving without microslip Reduced cooling output 575 mA*

Emergency (limp-home) mode Max. cooling output 0 mA

* average current value,

Ramp-shaped activation curve with 150 - 1000 mA in a second

Legend of Fig. 386_058

G193 Automatic gearbox hydraulic pressure N91 Solenoid valve 4

sender -1- N92 Solenoid valve 5
G194 Automatic gearbox hydraulic pressure N215 Electrical pressure control valve 1
sender -2- N216 Electrical pressure control valve 2
K1 Clutch 1 N217 Electrical pressure control valve 3
K2 Clutch 2 N218 Electrical pressure control valve 4
CCV Clutch cooling valve N233 Electrical pressure control valve 5
N88 Solenoid valve 1 N371 Electrical pressure control valve 6
N89 Solenoid valve 2 SPV System pressure valve (main pressure)
N90 Solenoid valve 3

25
 Gearbox subassemblies

Clutch functions

Overload protection

If the cooling oil outlet temperature exceeds a value The normal reaction of the driver to the warning
of approx. 160 °C (determined by G509), this means shudder is to ease back off the accelerator. If the
that the temperatures in the clutch have reached a driver ignores the warning shudder and continues
critical level. to press down on the accelerator, then, when the
These temperatures can occur, for example, when cooling oil outlet temperature exceeds approx.
driving away on very steep gradients (e.g. when 170 °C, clutch and engine torque will be reduced to
towing a trailer) or when the vehicle is held on an the extent that the engine runs powerlessly at a
incline using the clutch (i.e. without using the high idling speed.
brake). In this way, the driver is forced to ease back off the
accelerator.
In such a case, as a protective function, the clutch is
activated intermittently, this being perceived by the The clutch cooling system operates at maximum
vehicle occupants as heavy shudder (warning cooling output, and after a short time the clutch
shudder). cools down again.
The selector lever position indicator in the dash At the next attempt to drive away the vehicle, the
panel insert begins to flash at the same time; full engine torque will again be available and the
refer to page 84. journey can be continued.
The purpose of this "warning shudder" is to cause
the driver to abort drive-away and thus avert further
increases in clutch temperature.

Clutch cooling/cooling oil flow

Clutch cooling oil

386_021

Discharge of the clutch cooling

oil from the clutch

Multi-plate clutch oil

temperature sender G509
high 0

Oil pressure

26
Creep control Microslip control

"Creep" refers to the creep behaviour which The clutches are continuously engaged,
a conventional automatic gearboxes with a torque with a minimum slip rate of approx. 10 rpm.
converter exhibits when the engine is idling and a This is referred to as "microslip" on account of the
gear is selected. low slip value.
Microslip improves clutch control response and
The creep control function works like this: gearshift quality. Certain clutch adjustments are
when the engine is idling and a gear is selected, made under microslip.
a defined slip torque is set at the clutch (clutch The microslip also has the effect of reducing
torque) causing the vehicle to "creep". vibration between the engine and gearbox, thereby
This allows the vehicle to be manoeuvred (e.g. when improving the vehicle's vibrational behaviour.
parking) without using the accelerator pedal, thus
enhancing driving comfort. Clutch K2 is closed completely when the engine
reaches a speed at which it is no longer possible
The vehicle behaves as one would expect an to shift down into fifth gear. The special additives
automatic gearbox to. in the gearbox oil are protected in this way.
The clutch torque is adjusted to between 1 and
40 Nm, depending on the driving condition and
vehicle road speed. Clutch control adaptation

A special feature of the creep control is that of Comfortable clutch operation must be maintained
reduced clutch torque at vehicle standstill with the in all operating states and throughout the useful life
brake applied, whereby less torqueis required of the of the clutch.
engine (the clutch is further open). For this purpose, the relationship between clutch
Clutch torque is reduced to approx. 1 Nm, valve control current and clutch torque is subject to
depending on the brake pressure. continuous updating.
The tendency of the vehicle to creep is reduced
accordingly. This process of updating is necessary since the
friction coefficients of the clutches are continuously
This has a positive effect on fuel efficiency variable.
and comfort, because the vehicle has better The coefficient of friction is dependent on the
acoustics when at a standstill and considerably following continuously variable factors:
less brake pressure is required to hold the vehicle.
– ATF (quality, ageing, wear)
If the stationary vehicle begins to roll back on an – Oil temperature
incline with the brake only lightly applied, clutch – Clutch temperature
torque will be increased slightly. – Clutch slip
The vehicle must be held by increasing the brake
pressure or by applying the handbrake. To compensate for these influences, the
The vehicle behaves as one would expect a normal relationship between control current and
manual gearbox to. clutch torque is determined in various
driving conditions, e.g. under microslip,
and stored.

Note
After replacement of the mechatronics or the twin clutch or after updating of the gearbox control
unit programming, the clutch adaptation values must be reset using the diagnostic tester.
For this purpose, the "Basic Setting" procedure must be started under "Guided Functions" and the
described adaptation procedure carried out.

27
 Gearbox subassemblies

Safety shutdown

To counteract uncontrolled closing of a clutch, Oil feed to the clutch control for clutches K1 and K2
safety circuits are integrated in the hydraulic circuit. and for shift control is via a separate fail-safe oil
If the actual clutch pressure is clearly in excess of supply. This means that clutch K1 or part-gearbox 1
the nominal clutch pressure, this means that a or clutch K2 or part-gearbox 2 can be shut down
safety-critical malfunction is present. In this case, hydraulically.
the part-gearbox in question is depressurised by
means of a safety shutdown (refer to "Emergency The element responsible for safety shutdown of
program", page 85). part-gearbox 1 (2) is the electrical pressure control
Further events which trigger a safety shutdown are valve N233 (N371) and the accompanying safety
all faults to which the gearbox control unit reacts by valve 1 (2).
starting the emergency program.
Part-gearbox 1 enters emergency (limp-home)
mode; part-gearbox 2 is shut down (N371 not
activated (0 %),
Part-gearbox 2 enters emergency (limp-home)
mode; part-gearbox 1 is shut down (N233 not Note
activated (0 %). The hydraulic diagram shows the
pressure in the hydraulic system
when electronic pressure control
valves N233 and N371 are
deenergised.

Part-gearbox 1 Part-gearbox 2

Inlet - main pressure

N218

Safety valve 2

N233 N371

to K1
G194
Safety valve 1
to K2
G193

N216
N88 N89 N90 N91
N215

Clutch valve 2

N92
Clutch valve 1

386_101

28
N233/N371 deenergised

Main pressure
Pressure control valves N233 and N371 have a rising
current/pressure characteristic.
This means that if they are not activated, there will
be no control pressure acting on the safety valve
gates.
The gate is moved to the left by the spring force.
N233/N371 In this position, it disconnects the main pressure
to the respective clutch and shift control.
Safety valve 1/2

386_107

to clutch control

to shift control

N233/N371 energised

When the electromagnetic pressure control valve

Main pressure
N233 (N371) is energised, the control pressure acts
on the respective safety valve. The gate is moved to
the right against the spring force.
In this position it opens the pressure supply to the
clutch and shift control systems.
N233/N371

Safety valve 1/2

386_106

to clutch control

to shift control

high 0

Oil pressure Reference

For further information on electronic
Control pressure
pressure control valves N233 and N371,
refer to page 55.

29
 Gearbox subassemblies

Manual gearbox

Selector mechanism

The four gear change sleeves are actuated by The shift pressure flows through bores in the
hydraulically controlled shift fork. gearbox housing into the cylinder chambers
Each shift fork is located in two steel sleeves by (hydraulic cylinder) which are open at the rear.
means of roller bearings. The steel sleeves are press A travel sensor is assigned to each shift fork and
fitted into the gearbox housing; at the same time, determines the exact position and travel of the
they act as cylinder chambers for the hydraulic shift fork, refer to page 72.
pistons through which the shift forks can be
moved back and forth.

Shift fork 2/4 Shift fork 3/1

Shift fork R/6

386_029

Detent

Shift fork N/5

Detent gate

Hydraulic cylinder

Hydraulic piston

travel sensor solenoid

Roller bearing
Shift fork

386_030

30
The shift forks are pressurised in such a way that, Once the gear is selected, the corresponding
depending on requirements, they move to the left/ hydraulic cylinder is depressurised. The gear is held
right stop (corresponding gear selected) or to the in place by the selector teeth and by the shift fork
middle position (neutral position). detent. In the neutral position, the shift fork is held
in the centre position by the detent.
The gear change sleeve has a separate detent for
the neutral position.

386_031 386_032

Shift fork depressurised in neutral position Shift fork during the gearshift

depressurised
Note
Shift pressure To ensure proper functioning of the
gearbox, the exact positions of the
shift forks in relation to the gearbox
control unit must be known. Travel
sensors determine the position of the
shift forks; also refer to page 72.
Due to manufacturing tolerances,
the respective end positions and the
synchronisation points of each shift fork
(each gear) in the gearbox control unit
To maintain a constant shift time, the gearshift
must be programmed by teach-in (basic
pressure is adapted according to gearbox
setting).
temperature and gearshift duration, and can
After replacement of the mechatronics or
be up to 20 bar.
entries relating to the selector mechanism
are made in the fault memory, the basic
setting procedure (basic alignment) must
In the event of malfunction or if incorrect shift
be carried out using the diagnostic tester.
positions are executed, the part-gearbox concerned
For this purpose, the "Basic setting"
is shut down hydraulically by means of the safety
proceduremust be started under "Guided
shutdown function; refer to "Safety shutdown",
Functions" and the described adaptation
page 28.
procedure then carried out.

31
 Gearbox subassemblies

Power flow
1.
2.
Reverse (R) 3.
gear 4.

Clutch K1
Input shaft 1
Output shaft 2
Final drive/differential

6.
386_028
5.

R.

1.
2.
1st gear 3.
4.

Clutch K1
Input shaft 1
Output shaft 1
Final drive/differential

6.
5.
386_022

32
 1.
2.
2nd gear 3.
4.

Clutch K2
Input shaft 2
Output shaft 1
Final drive/differential

6.
386_023
5.

1.
3rd gear 2.
3.
4.

Clutch K1
Input shaft 1
Output shaft 1
Final drive/differential

6.
5. 386_024

33
 Gearbox subassemblies

Power flow
1.
4th gear 2.
3.
4.

Clutch K2
Input shaft 2
Output shaft 1
Final drive/differential

6.
5. 386_025

1.
2.
5th gear 3.
4.

Clutch K1
Input shaft 1
Output shaft 2
Final drive/differential

6.
5. 386_026

34
 1.
2.
6th gear 3.
4.

Clutch K2
Input shaft 2
Output shaft 2
Final drive/differential

6.
386_027
5.

Synchromesh Change gear Synchroniser ring

Single cone synchromesh

The gearbox has single cone

synchromesh on 4th, 5th and 6th gear.

386_034

Change gear
Inner ring
Double cone synchromesh Intermediate ring
Synchroniser ring
The gearbox has double cone
synchromesh on reverse.

386_035

Change gear
Inner ring

Triple cone synchromesh Intermediate ring

Synchroniser ring
The gearbox has triple cone
synchromesh on 1st, 2nd and 3rd gear.

386_033

The above-specified assignments of the synchromesh units to the individual gears and the illustrations
conform to the gearbox specifications valid to week 45/05. The synchromesh mechanisms of gears 1 to 4
have since been optimised in the course of further development work.

35
 Gearbox subassemblies

Hydraulic control

The shift forks are controlled by four solenoid valves (N88 - N91) and a so-called "multiplexer".
The multiplexer is controlled by the solenoid valve N92.
The multiplexer makes it possible to control the eight hydraulic cylinders (each shift fork has two
hydraulic cylinders) using only four solenoid valves.

When solenoid valve N92 is deenergised, the When the solenoid valve N92 is energised, the
multiplexer is in its basic setting. It is pressed multiplexer is pressed against the left-hand stop
against the right-hand stop by the spring pressure. by the control pressure.
The following shift forks/gears can be activated: The following shift fork/gears can be activated:

N88 + N89 control shift forks 3-1 N88 + N89 control shift forks -5
N90 + N91 control shift forks R-6 N90 + N91 control shift forks 4-2

The shift pressure generally corresponds to the

main pressure. To minimise shift noise, the shift
pressure is reduced in certain situations by means
of electronic pressure control valves N233 and
N371. You can find more information on page 57.

Main pressure

Safety valve 2
N233 N371

G194
to K1
Safety valve 1 to K2

G193

N216
N88 N89 N90 N91
N215

N92

Gear selector valves 1- 4

Multiplexer

Shift fork

high 0 386_036

Oil pressure

control pressure

36
Multiplexer function

386_037

Solenoid valve N92 deenergised

386_038

If the solenoid valve N92 is deenergised, the Connections "a" are connected to the pressure
multiplexer is in its basic setting. It is pressed ports. Connections "b" are ventilated.
against the right-hand stop by the spring pressure.

Solenoid valve N92 energised

386_039

When the solenoid valve N92 is energised, the Connections "b" are connected to the
multiplexer is pressed against the left-hand pressure ports. Connections "a" are ventilated.
stop by the control pressure.

high 0

Oil pressure

Control pressure

37
 Gearbox subassemblies

Shift control

The following shift forks/gears can be activated when N92 is deenergised: 386_040

N88 + N89 control shift forks 3-1

N90 + N91 control shift forks R-6

386_041
No control pressure - solenoid valve N92 deenergised

38
 386_042
The following shift forks/gears can be activated when N92 is energised:

N88 + N89 control shift forks N-5

N90 + N91 control shift forks 4-2

386_043
Maximum control pressure - solenoid valve N92 energised

39
 Gearbox subassemblies

Gearshift sequence

Initial state Situation 2

Engine idling, selector lever in position "P" or "N". At the same time, part-gearbox 1 (now "available")
The driver wants to drive away forwards and shifts from reverse to 1st gear and clutch K1 is filled.
accelerate, and, therefore, selects selector lever Clutch K1 receives the full torque, and K2 is
position "D" or "S" and pushes down the accelerator completely reopened.
pedal.
Normally the reaction time of the gearbox is
Situation 1 sufficient to complete the shift from reverse to
1st gear by the time the driver depresses the
In selector lever position "P" or "N", the driver input accelerator, and the vehicle moves away in 1st gear.
– forwards or reverse – is initially unknown to the In a driving condition where the driver moves the
gearbox. Is "R" or "D" selected? selector lever from "N" to "D" and simultaneously
depresses the accelerator, the reaction time of the
Since reverse and 1st gear areassigned to part- gearbox will not be sufficient and, therefore, the
gearbox 1, both gears cannot be preselected vehicle will initially move away in 2nd gear until the
simultaneously. aforementioned shift is completed in part-gearbox 1.
To reduce the reaction time at drive-away with
the selector lever in position "P" or "N", reverse is
preselected in part-gearbox 1 and second gear is
preselected in part-gearbox 2.

When the selector lever is moved into position

"D" or "S", clutch K2 is initially filled and a torque
transmitted via 2nd gear.
Note
A normal gearshift is completed
within approx. 200 ms.
However, very low temperatures
prolong gearshifts due to the higher
viscosity of the gearbox oil and the
associated increase in the reaction
time of the hydraulic control system.

Situation 1 Situation 2
1.
2.
3. 2.
4. 3.
4.
K1
K2

K2

6. 6.
5.

R
386_044

40
 Initial state

Acceleration in 1stgear.
Additional acceleration after drive-away.

Situation 3

When the characteristic for the upshift from 1st to

2nd gear is reached, 2nd gear is selected by
overlapping operation of clutches K1 and K2.
This means that clutch K1 opens while clutch K2
closes and transmits the engine torque. Engine torque intervention
To enhance shift comfort and conserve the clutches,
engine torque is reduced during the clutch overlap
phase.
K2
After the upshift from 1st to 2nd is complete,

Torque
part-gearbox 1 shifts into 3rd gear (the gear is
Engaging Disengaging
preselected). The aforementioned process is clutch clutch
repeated alternately during the subsequent
K1
gearshifts from 2-3, 3-4, 4-5 and 5-6, and also
during downshifts.
Time
In selector lever position "S" and in tiptronic mode,
engine torque is increased during the downshift in Overlap/torque reception
order to reduce the shift time (synchronisation
speed is reached more quickly) and enhance
gearshift comfort.

Situation 3

1. 1.
2.
3.
4.

K2

6.
5. 5.

386_045 386_047

41
 Gearbox subassemblies

Gearshift sequence/multi-step downshifts

Power flow is not interrupted, not even during A multi-step downshift, e.g. from 6th gear to
multiple shifts (gears are skipped). Skipping of 2nd gear, is made via 5th gear (6 –> 5 –> 2).
gears is possible (e.g. 5 –> 3). However, one gear The driver does not notice this transition, however,
is positively engaged at all times. Gearshifts from because 5th gear is engaged only momentarily (for
one part-gearbox to the other (e.g. 6 –> 3) are made the duration of the downshift from 6th to 2nd gear),
directly. and the increase in engine speed is adapted by
During gearshifts within a part-gearbox, power regulating clutch K1 accordingly; refer to
flow is maintained by intermittent shifting to the Fig. 386_048.
"available" part-gearbox.

Downshift from 6th to 2nd in less than 0.9 s

Clutch torque Nm

K1 K2
Engine speed rpm

n Input shaft 2
n Engine
n Input shaft 1

Time s

386_048

Start of gearshift • Controlled engine start-up via

• 6th gear active 5th gear (part-gearbox 1, clutch K1)
• Engine start-up • 2nd gear is engaged in part-gearbox 2.
via clutch K2

Transmission of engine torque Transmission of

to clutch K1 (5th gear) engine torque
to clutch K2

42
 Parking lock
Generally, no traction is available when the engine
is at a standstill (both clutches, K1 and K2, are Locking pawl
open). The 02E gearbox, therefore, as is customary
with automatic gearboxes, requires a parking lock.

The parking lock gear is coupled to the final

drive (spur gear). The locking pawl is actuated
mechanically with the selector lever cable.
The selector lever cable actuates the parking
lock only.

Parking lock gear

Function: 386_049

Cable to selector lever

Lever Selector lever in position R, N, D or S

Rollers

Locking pawl
Spring 1

Gate valve

Parking lock gear

Selector lever position "P"

(locking pawl not engaged)

In selector lever position "P" the locking pawl is

moved by means of the cable pull and lever in such
a way that it engages the gearing of the parking
lock gear and, consequently, blocks the final drive.

When the selector lever is shifted into position "P",

Spring 1 preloaded
the locking pawl of the parking lock is moved via
Gate the cable pull and the lever in such a way that it
engages the gearing of the parking lock gear and,
consequently, blocks the final drive.

Selector lever position "P "

(locking pawl engaged)

When the vehicle moves (the parking lock gear

continues to rotate), the locking pawl is moved
automatically into the next tooth space in the
parking lock gear by preloaded spring 1 and by
the shape of the gate.
Spring 1 relieved 386_050

For safety reasons, the shape and flank angle of the locking pawl as well as the teeth of the parking lock gear
and the pressure force of the locking pawl are such that the locking pawl does not engage when the vehicle is
travelling at speeds of higher than approx. 7 kph.
If the parking lock is inadvertently actuated at higher speeds, the locking pawl will ride loudly over the teeth
of the parking lock gear.

43
 Gearbox subassemblies

All-wheel drive - power distribution

The 02E gearbox is available for the following The 02E gearbox for all-wheel drive has a bevel box
powertrain types: which transfers the gearbox output torque to the
front-wheel drive and quattro all-wheel drive. Haldex coupling.
The gearbox for quattro all-wheel drive is the
all-wheel drive concept with Haldex coupling.

Bevel box 02M (i = 1 : 1.6)

Haldex coupling 02D/0AV

Front axle drive

Haldex coupling

386_051

Rear axle differential Rear axle drive (i = 1.6 : 1) Rear axle differential

44
Bevel box

Front axle drive

Power flow to Haldex coupling

to front To front
left wheel right wheel

386_053

Front axle differential

to rear axle drive

The speed of the front axle drive is increased by a factor of 1.6 in the bevel box and
transmitted to the Haldex coupling by prop shaft.
The increase in speed improves the response of the Haldex coupling.
Torque is reduced, thereby allowing a smaller prop shaft design to be used.
Speed is then reduced by a factor of 1.6 in the rear axle drive.

Reference
For information on the Haldex coupling,
refer to SSPs 206 and 333.

45
 Gearbox subassemblies

Oil supply

Power transmission in the 02E gearbox is dependent The oil supply system also includes the following
on the hydraulics and on the electrical system. components or subassemblies:

Without oil pressure and electrical current, The main pressure control adapts the main
there is no power transmission! pressure according to engine torque and gearbox
oil temperature. The main pressure is between 3 bar
The oil supply ensures the availability of oil pressure and 20 bar.
and oil flow for The main pressure control system includes the
… the multi-plate clutches, system pressure valve (SPV) and electrical pressure
… the clutch cooling system, control valve N217 (refer to page 47 Fig. 386_055
… the shift hydraulics and page 56).
as well as the lubrication and cooling of all
components. A pressure limiting valve (PLV) opens at
approx. 32 bar and protects the components in
The gearbox oil has to meet a variety of stringent the oil circulation system against excessively high
and, in some cases, conflicting requirements. pressures.
In response to these special requirements, a In addition to the suction filter, a separate
special gearbox oil was developed for twin-clutch compressed air filter provides effective cleaning of
gearbox 02E. the gearbox oil and allows increased operational
For this reason, the approved oil type prescribed in reliability.
the parts catalogue must be used. The filter cartridge must be replaced when
changing the oil and after repair work.
The front-wheel drive gearbox has only one oil For magnetic abrasion, there are permanent
supply. The all-wheel drive bevel box has its own magnets on the suction filter and in the oil drain
supply of axle oil. screw.

The oil pump – a high performance vane cell pump – The oil cooler is directly flanged to the gearbox and
ensures a reliable supply of oil. The oil pump is integrated in the engine cooling system (coolant-oil
driven via the pump shaft running at engine speed. heat exchanger).
The pump shaft is coaxially mounted inside hollow
input shaft 1 and is driven by the driving disc by The gears and bearings are lubricated by means of
means of a stub shaft spline. oil spray pipes which form the return linesof the
Max. power consumption of the oil pump is 2 kW. heat exchanger and the pressure oil filter circuit.
The oil level can be kept to a minimum through
systematic lubrication. This reduces churning
losses and improves efficiency.

Oil pump input shaft

Input shaft 1 (pump shaft)
Oil pump
Driving disc

386_056

46
 Oil pump

N217

PLV
SPV

Oil cooler

CCV
POF
to twin clutch
(cooling)
Oil spray pipes

N218

DC
386_055

to clutch control
and shift control

high 0

Oil pressure

Legend

PLV Pressure limiting valve

POF Pressure oil filter
CCV Clutch cooling valve
N217 Electrical pressure control valve 3
N218 Electrical pressure control valve 4
SF Suction filter
SPV System pressure valve (main pressure)

47
 Gearbox subassemblies

Hydraulic diagram of 02E gearbox

Oil pump Main pressure

Twin clutch
N217

K1
PLV
SPV

Oil cooler

CCV

POF
Oil spray pipes

N218

DC

K2

N233 N371
SV 1 SV 2

to K1 to K2

G194

G193

N216

N88 N89 N90 N91

N215

Clutch valve 2
Clutch valve 1

N92

Multiplexer
Shift fork

high 0 386_058

Oil pressure

Gear change sleeve Gear wheel

Control pressure

48
Oil supply/overview
Oil cooler
Pressure oil filter
Twin clutch

Filter cartridge
Hydraulic cylinder
for shift fork

Mechatronic
module
Oil spray pipes

Suction filter

386_057

Oil pump

Hydraulic cylinder for

shift fork

Legend

PLV Pressure limiting valve N215 Electrical pressure control valve 1

POF Pressure oil filter N216 Electrical pressure control valve 2
G193 Automatic gearbox hydraulic pressure N217 Electrical pressure control valve 3
sender -1- N218 Electrical pressure control valve 4
G194 Automatic gearbox hydraulic pressure N233 Electrical pressure control valve 5
sender -2- N371 Electrical pressure control valve 6
K1 Clutch 1 SF Suction filter
K2 Clutch 2 SV Safety valve
CCV Clutch cooling valve SPV System pressure valve (main pressure)
N88 Solenoid valve 1
N89 Solenoid valve 2
N90 Solenoid valve 3
N91 Solenoid valve 4
N92 Solenoid valve 5

49
 Gearbox control unit

Gearbox control unit –

mechatronic module
The mechatronic module is the nerve centre of The mechatronic module controls, regulates and
the gearbox. It makes up a well balanced unit by executes the following functions:
combining the electro-hydraulic control unit
(actuators), the electronic control unit and most of – Adaptation of the oil pressure in the hydraulic
the sensors (electronic module). The mechatronic system to the respective requirements and needs
module should, therefore, only be replaced as a – Twin clutch control
complete part. – Clutch cooling control
– Shift point selection
– Gear-shifting
– Communication with other control units
– Emergency program
– Self-diagnosis
Note
After replacement of the mechatronic
module, the gearbox mechanism must
be adapted using the diagnostic tester.
For this purpose, the "Basic Setting"
20-pin connector
procedure must be started under to vehicle
Channel plate with electronic module
"Guided Functions" and the described (on the back),
adaptation procedure then carried out. also refer to Fig. 386_117
If basic setting is not carried out, the vehicle
will only run in 1st, 2nd and reverse (R) gear.
In this case, a fault message indicating that
basic setting has not been carried out is
stored in the fault memory; also refer to
page 73.

Channel plate

Electro-hydraulic
control unit

386_112

Note
Important: the mechatronic module must
be handled in accordance with the code of
practice relating to electrostatic discharge
(ESD electro-static discharge)!

For further information regarding the

mechatronic module, please refer to
Printed circuit
SSP 284, from page 4.
board (PCB)

50
Function diagram of the mechatronic module

20-pin connector to vehicle wiring loom 386_062

Connector
on electronic module
of the mechatronic
module
Pin assignments of 20-pin connector Combined sender G509/G182 is
a separate component and is integrated
to mechatronic module in the gearbox (refer to page 67/68)

Pin 1 K-wire (diagnostics)

Pin 2 not used
Pin 3* tiptronic steering wheel Tip–
Pin 4,5 not used Legend
Pin 6* V-signal (speedo/dash panel insert),
TT 8N MY 03 only G93 Gearbox oil (ATF) temperature sender
Pin 10 Powertrain CAN bus high G182 Gearbox input speed sender
Pin 11 Term. 30 G193 Automatic gearbox hydraulic pressure
Pin 12* R-signal (reversing light control) sender -1-
Pin 13 Term. 15 G194 Automatic gearbox hydraulic pressure
Pin 14* tiptronic steering wheel Tip+ sender -2-
Pin 15 Powertrain CAN bus low G195 Gearbox output speed sender -1-
Pin 16 Term. 31 G196 Gearbox output speed sender -2-
Pin 17 P/N signal (starter control) G487 Gear selector travel sensor 1
Pin 18 Term. 30 G488 Gear selector travel sensor 2
Pin 19 Term. 31 G489 Gear selector travel sensor 3
Pin 20 not used G490 Gear selector travel sensor 4
G501 Drive shaft 1 speed sender
* only in the Audi TT (8N) G502 Drive shaft 2 speed sender
G509 Multi-plate clutch oil temperature sender
G510 Temperature sensor in control unit

J743 J743 Mechatronic control unit

N88 Solenoid valve 1

Electronic module N89 Solenoid valve 2
N90 Solenoid valve 3
N91 Solenoid valve 4
N92 Solenoid valve 5
N215 Electrical pressure control valve 1
N216 Electrical pressure control valve 2
N217 Electrical pressure control valve 3
N218 Electrical pressure control valve 4
N233 Electrical pressure control valve 5
N371 Electrical pressure control valve 6

Channel plate 386_117

51
 Gearbox control unit

Electro-hydraulic control unit

The electro-hydraulic control unit comprises the

following components:

– Valve body
– 5 hydraulically actuated switch valves
(gate valves)
– Pressure limiting valve
– 5 electrical solenoid valves
– 6 electronic pressure control valves (EDL)
– Channel plate with 2 pressure sensors
– Printed circuit board (PCB)

Reference
Refer to hydraulic diagram on page 48.
Refer to description of valves, from page 54.

Electro-hydraulic control unit

System pressure valve

(main pressure)
N216

N217
N215

Pressure limiting valve

N218

N90
Multiplexer

N91

N92

N371

386_060

Safety valve 2

Safety valve 1 N88 N89 N233

52
 from oil cooler

to oil cooler

2nd gear
4th gear
3rdgear
1st gear

from the oil pump

Clutch cooling

Clutch pressure K2
to oil pump

Clutch pressure K1

6thgear

5th gear
Reverse (R) gear

N-gear

Electro-hydraulic control unit with

channel plate and PCB

Legend

N88 Solenoid valve 1

N89 Solenoid valve 2
N90 Solenoid valve 3
N91 Solenoid valve 4
N92 Solenoid valve 5
N215 Electr. pressure control
valve 1
N216 Electr. pressure control
valve 2
N217 Electr. pressure control
valve 3
N218 Electr. pressure control
valve 4
N233 Electr. pressure control
valve 5
N371 Electr. pressure control
valve 6

386_063

53
 Gearbox control unit

Description of the valves

The hydraulic switch valves (gate valves) Note
and their tasks:
Manufacturing tolerances of the electro-
The system pressure valve (SPV) controls the oil hydraulic control unit (e.g. EDL, gate
pressure which is required to control the gearbox. valves, valves etc.) and the power
It is activated by N217 in dependence on engine modules of the electronic control
torque and gearbox oil temperature. unit are determined on a test bench
and compensated by basic programming
The clutch cooling valve (CCV) controls the twin of the electronic control unit.
clutch cooling oil. The CCV is activated by N218; This basic programming is not covered
refer to pages 25 and 57. by service, which is why the mechatronic
module can only be replaced as a
The two safety valves SV 1 and SV 2 allow hydraulic complete unit.
shutdown of the two part-gearboxes. Valves SV 1
and SV 2 are activated by N233 and N371; refer to
pages 28 and 57.

The multiplexer allows the 8 hydraulic cylinders

for the shift forks to be controlled with only
4 electromagnetic valves.
The multiplexer is activated by N92;
refer to page 37.

The pressure limiting valve (PLV) ensures that the

pressure in the system does not exceed approx.
32 bar, and thus protects all components affected,
Electro-hydraulic control unit
directly and indirectly (refer to page 48).

Solenoid valves N88, N89, N90, N91 and N92

are electromagnetic switch valves.
They are also known as 3/2 valves, which means
3 connections and 2 switch positions (open/closed
or ON/OFF). When no electrical current is present, N90
the pressure connections are closed and the control
ports to the oil sump are open.
Solenoid valves N88 to N91 control the gear N91
selectors and N92 controls the multiplexer;
refer to page 36.

The channel plate makes the line connection

between the mechatronic module and the gearbox
housing.
Printed circuit broad
The two hydraulic pressure senders G193 and G194 (PCB)
are integrated in the channel plate.

The printed circuit board (PCB) connects the

electronic control unit to the solenoids and the
electronic pressure control valves.

SV2

SV 1

N88

386_112

54
 Electronic pressure control valves (EDL) N215, Electronic pressure control valves with rising
N216, N217, N218, N233 and N371 characteristic

The electronic pressure control valves convert an EDLs N215, N216, N233 and N371 have a rising
electrical control current into a near-proportional current-pressure characteristic. This means that
hydraulic control pressure. the control pressure rises with increasing control
There are EDLs with a so-called rising or falling current.
characteristic.
Valve deenergised = no control pressure
(0 mA = 0 bar)

In case of failure of one of these valves, the

corresponding gate valve is not activated and
the associated functions fail.

Channel plate G193 Rising characteristic

Electronic module
G194

386_066

P = pressure
I = current

Electronic pressure control valves with falling

characteristic

Electronic pressure control valves N217 and N218

System pressure valve have a falling current-pressure characteristic.
(main pressure)
This means that the control pressure decreases with
decreasing control current.

Pressure limiting valve

Valve deenergised = maximum control pressure

In case of failure of N217, it is ensured that the

Multiplexer maximum main pressure is present.

In case of failure of N218, it is ensured that the

maximum cooling oil flow is present.
N92

Falling characteristic

N89

386_067

P = pressure
I = current

55
 Gearbox control unit

Electronic pressure control valves 1/2 N215 and N216 Electrical pressure control valve 3 N217

Electrical pressure control valvesN215 and N216 are N217 supplies the control pressure for the system
a special feature. They control the clutch pressure pressure valve (SPV) and controls the main pressure
(from 0 to 10 bar) directly, i.e. without the use of a in the hydraulic system. The pressure in the system
downstream hydraulic gate valve; refer to "Clutch is adapted to the operating conditions, i.e.
control" on page 24. unnecessarily high pressures are avoided by
adjusting the main pressure to the existing engine
N215 controls the clutch pressure of clutch K1. torque.
This results in a significant increase in gearbox
N216 controls the clutch pressure of clutch K2. efficiency. Without this adaptation, the high
pressure necessary for full-throttle operation
Valves N215 and N216 are activated according to would have to be maintained.
engine speed, gearbox input speed and the speeds
of the input shafts. N217 is activated according to engine torque and
gearbox oil temperature.
Effects of malfunctions
Effects of malfunction
As mentioned previously, both valves have a
rising characteristic. If they are not activated, If N217 fails, the maximum main pressure is set
the associated function is not available. according to the falling characteristic. This
The gearbox control unit shuts down part-gearbox increases fuel consumption and can lead to
in question and the relevant emergency program is noisy gearshifts.
activated.
Fault indication: yes
The valves are monitored by means of hydraulic
pressure senders G193 and G194; refer to page 71.
If the actual pressure deviates too much from the
nominal pressure, in this case, too, the part-gearbox
in question is shut down and the relevant emergency
N216
program is activated.

Fault indication: yes

N215

N218

Note
Incorrect engine torque values from the
N371
engine control unit will impair clutch and
gearbox control, which, in turn, can result in
loss of shift comfort or gearbox and clutch
damage.

56
Electrical pressure control valve 4 N218 Electronic pressure control valves 5/6 N233/N371

N218 supplies the control pressure for the clutch Electrical pressure control valve N233 (N371)
cooling valve (CCV), and hence controls the cooling activates safety valve 1 (2) and thereby allows the
oil flow to the twin clutch; refer to page 25. part-gearbox in question to be shut down (hydraulic
safety shutdown).
Effects of malfunction
Part-gearbox 1 (N233) and part-gearbox 2 (N371);
If N218 fails, the maximum cooling oil flow will be refer to page 28.
set according to the valve characteristic. This will
increase fuel consumption and can cause gear- Electronic pressure control valves N233 and N371
shifting problems at low ambient temperatures. are activated at a duty cycle of approx. 62 %.
At this value the control pressure is already so high,
If the cooling system fails (e.g. due to sticking of the safety valves are fully open. The advantage of the
the gate valve or valve), the clutch will overheat. low duty cycle is that the valves and oil are heated
less and hence conserved.
Fault indication: yes
To minimise gear-shifting noise, the shift pressure
is reduced by means of electronic pressure control
valves N233 and N371. The valves are activated at a
reduced duty cycle (< 62 %).

Effects of malfunction

As mentioned previously, both valves have a

rising characteristic. If they are not activated,
the associated function will not be available. This
means that the part-gearbox in question will not be
functional (no clutch activation and shift control).
The gearbox control unit activates the relevant
emergency program; refer to page 80.

Fault indication: yes

N217

N233

386_060

57
 Gearbox control unit

Electronic module
The electronic module is an inseparable unit Note
comprising the electronic control unit and most of
the sensors. The electronic module is bolted to the The control unit and the channel
channel plate. The aluminium channel plate serves plate must not be separated!
as the electronic module mounting plate and holds
hydraulic pressure senders G193 and G194. Neither the control unit nor the
sensors of the electronic module
The electronics of the mechatronic control unit J743 can be replaced individually.
are connected directly to the channel plate by means
of a heat conductive gel. This gel dissipates to the
gearbox oil the heat which is generated by the
electronics.

20-pin connector

G193

Mechatronic G194
control unit J743
Electronic
module
Electronic
module

Channel plate

Channel plate
386_117 386_059

Mechatronic control unit J743

(gearbox control unit)
Note
Control unit J743 is the nerve centre of the The use of microelectronics
mechatronic module. J743 acquires, evaluates and demands special care with regard
transfers all the information required for operation to protection against electrostatic
of the gearbox and peripheral systems. discharge.
J743 generates the output signals for the actuators Persons handling the mechatronic
inside and outside of the gearbox. module must discharge static by
Communication with the periphery is implemented touching a grounded surface
mainly by powertrain CAN bus. (e.g. heating pipe, car lift) or the
vehicle's grounding point before
On account of the fact that the gearbox control unit working on the vehicle.
is integrated in the gearbox (it is immersed in the Do not touch the plug contacts of
gear oil), it is vital to monitor the temperature of the the electronic module.
electronic components. High temperatures
sigificantly affect the service life and the functional Persons handling the mechatronic
capability of electronic components. module must observe the code of
The gearbox oil temperature is monitored by practice relating to electrostatic
two temperature sensors (G93/G510) which are discharge (ESD electro-static
integrated in the gearbox control unit. They the discharge)!
temperature directly at critical components.

58
Overview of the sensors in the electronic module
and in the gearbox

G93 Gearbox oil (ATF) temperature sender G501 Drive shaft 1 speed sender
G182 Gearbox input speed sender 2) G502 Drive shaft 2 speed sender
G193 Auto. gearbox hydraulic G509 Multi-plate clutch oil temperature sender2)
pressure sender -1- (K1) 1) G510 Temperature sensor in control unit
G194 Auto. gearbox hydraulic J743 Mechatronic control unit
pressure sender -2- (K2) 1)
G195 Gearbox output speed sender -1-
G196 Gearbox output speed sender -2-
G487 Gear selector travel sensor 1 (shift fork 3/1)
G487 Gear selector travel sensor 2 (shift fork 2/4)
G487 Gear selector travel sensor 3 (shift fork -/5)
G490 Gear selector travel sensor 4 (shift fork 6/R)

Connector
Vehicle wiring loom

G487 G488

G501 G502

G93

G196
J743

G195

G510

G490

386_069

G489

Connector
1)
Hydraulic pressure senders G193 and G194 G182 and G509 2)
are component parts of the channel plate.

2)
Sensors G182 and G509 are combined in a
single component; refer to page 67 and 68.

59
 Gearbox control unit

Function diagram of the Audi A3 (8P) and Audi TT (8J)

N110

F319

P-signal
to J527*

386_070

Legend

E313 Selector lever sensor system Input

(selector lever)
F189 tiptronic switch Output
F319 Selector lever locked in position P switch
J527 Steering column electronics control unit
J743 Mechatronic control unit * The P-signal serves to enable the ignition key
K K-wire (diagnostics) withdrawal lock
L101 Selector lever display illumination
N110 Selector lever lock solenoid
Y26 Selector lever position indicator unit

60
Function diagram of the Audi TT (8N)

Reverse (R) gear signal for controlling

the reversing lights
P/N signal for controlling to the reversing lights
term. 50

Tip– tiptronic steering wheel

Tip+ tiptronic steering wheel

386_071

Legend

E313 Selector lever sensor system Input

(selector lever)
F189/a tiptronic switch (tip gate signal) Output
F189/b tiptronic switch (Tip–/Tip+ signal)
J207 Starter inhibitor relay
J219 Reversing light relay
J743 Mechatronic control unit
K K-wire (diagnostics)
L101 Selector lever display illumination
N110 Selector lever lock solenoid
V Road speed signal (MY 03 only)
Y26 Selector lever position indicator unit

61
 Gearbox control unit

CAN information exchange in the Audi A3 (8P) Audi TT (8J)

(gearbox-specific)

Mechatronic control unit J743

Selector mechanism active

Engine power reduction
Air conditioner compressor OFF
Clutch status
Idle speed increase
Gearbox control unit coding
Engine control unit coding
Target gear or selected gear
Nominal engine torque
Motion resistance (drag)
Gearbox emergency (limp home) mode
Nominal cooling output
OBD status
Fault memory entry
Gearbox torque loss
Desired synchronisation speed
Shift lock lamp
Gear signal

Selector lever sensor system E313

Selector lever position

tiptronic status
Shift lock shift command
Fault conditions

Data bus diagnostic interface J533

Mileage (km), time, date

CAN Sleep Acknowledge

Reference
You will find detailed information on the
CAN bus in SSPs 186 and 213.

62
Engine control unit JXXX ESP control unit J104

Throttle position TCS/EBC activation

Throttle valve position EBC activation
Kick-down ABS braking
Engine torque (nominal/actual) EDL intervention
Engine torque loss ESP intervention
Engine speed ESP status OFF/ON
Driver torque input TCS shift control
Coolant temperature Lateral acceleration
Brake light switch and brake test switch Longitudinal acceleration
A/C activation Wheels speeds
Cruise control system status Vehicle speed
Altitude info Brake pressure
Idling information Handbrake status
Engine speed regulation
Engine control unit coding
Gearbox control unit coding
Particulate filter regeneration cycle start

Steering angle sender G85

Steering wheel angle

Steering wheel angular speed

Steering column electronics

Control unit with display in
control unit J527
dash panel insert J285
(serves as the LIN master for
control unit J453)
Ambient temperature

Onboard power supply control unit J519;

refer to pages 84 and 85

Trailer detector control unit J345

Multi-function steering wheel
Trailer detected
control unit J453

tiptronic status
tiptronic shift command +/–

386_072

= information which is sent by the mechatronic control unit

= information which is received by the mechatronic control unit

63
 Gearbox control unit

CAN information exchange in the Audi TT (8N)

(gearbox-specific)

Mechatronic control unit J743

Selector mechanism active

Engine power reduction
Air conditioner compressor OFF
Clutch status
Idle speed increase
Gearbox control unit coding
Engine control unit coding
nominal gear or selected gear
Target/nominal engine torque
Motion resistance (drag)
Gearbox emergency (limp home) mode
Nominal cooling output
OBD status
fault memory entry
Gearbox torque loss
Desired synchronisation speed
Shift lock lamp
Gear signal

Selector lever sensor system E313 Control unit with display in

dash panel insert J285
Selector lever position
tiptronic status Mileage (km), time, date
Shift lock shift request Ambient temperature
Fault conditions Handbrake status

64
Engine control unit J220 ESP control unit J104

Throttle position TCS/EBC activation

Throttle valve position EBC activation
Kick-down ABS braking
Nominal/actual engine torque EDL intervention
Engine torque loss ESP intervention
Engine speed ESP status OFF/ON
Driver torque input TCS shift control
Coolant temperature Lateral acceleration
Brake light switch and brake test switch Longitudinal acceleration
A/C activation Wheel speeds
Cruise control system status Vehicle speed
Altitude info Brake pressure
Idling information
Engine speed regulation
Engine control unit coding
Gearbox control unit coding

Steering angle sender G85

Powertrain CAN bus
Steering wheel angle
Steering wheel angular speed

= information which is sent by the mechatronic control unit 386_073

= information which is received by the mechatronic control unit

65
 Gearbox control unit

Sensors
Gearbox oil (ATF) temperature sender G93
Temperature sensor in control unit G510

On account of the fact that the gearbox control unit Signal utilisation
is integrated in the gearbox (it is immersed in the
gear oil), it is vital to monitor the temperature of the Temperature monitoring/protective function
electronic components and, therefore, the gearbox Adaptation criterion
oil temperature. Shift pressure adaptation
High temperatures significantly affect the useful Warm-up program
life and the functional capability of electronic
components. Effects of signal failure
Due to the stringent safety requirements which
apply to temperature monitoring, two sensors Both senders check each other and, in case of
(G93/G510) are integrated in the control unit failure of one of the senders, the other sender
electronics and measure directly the temperature generates a substitute signal.
of critical components. In case of failure of both senders, an emergency
Thus, temperature reducing measures can be signal is generated from the engine temperature.
initiated at an early stage (refer to "Temperature
monitoring/protective function"). Fault indication: no, fault memory entry only

The aluminium channel plate serves as a heat Temperature monitoring/protective function

exchanger for the electronics.
Since there is a continuous flow of gearbox oil When the temperature (G93) exceeds 138 °C, the
flows through the channel plate, its temperature mechatronic control unit J743 reduces the engine
is approximately the same as that of the gear oil. torque.

G93 supplies exact data and is, as it were, the main At temperatures up to 145 °C, the engine torque is
electronics and gearbox oil temperature sensor. reduced incrementally until the engine is running at
G510 is principally used for verifying the plausibility idle speed. The multi-plate clutches are open and
of sensor G93. the vehicle has no drive.

In addition to safety aspects, thegearbox oil

temperature affects the clutch control and hydraulic
control systems. Therefore, it is a key factor in the
regulation and adaptation functions.

J743

G93

G510

386_069

66
Multi-plate clutch oil temperature sender G509

The G509 and the gearbox input speed sender G182 Effects of signal failure
are integrated in a unit.
G509 measures the temperature of the cooling oil Sporadic losses of signal will result in overly harsh
discharged from the twin clutch. gearshifts or gear drop-out.
The highest gearbox oil temperatures occur here.
In the event of complete loss of signal, the
G509 has a very short reaction time to changes in gearbox control unit utilises the signals from
temperature. It delivers very exact measurement data senders G93 and G510.
within a range of temperatures from –55 °C to +180 °C.
In all fault situations, no corrective
Signal utilisation action is taken, rather an entry is made
in the fault memory only (without fault indication).
Monitoring of the temperature of the cooling oil
discharged from the twin clutch in order that
counter-measures can be taken at approx. 160 °C.

Refer to "Clutch functions/overload protecti

on" on page 26.

386_124

Connection to mechatronic module

G509 G182

67
 Gearbox control unit

Gearbox input speed sender G182

G182 is a Hall sender. It monitors the input speed of the twin clutch.
The encoder function is performed by the outer plate carrier of clutch K1, which in turn is positively
connected to the main hub and the outer plate carrier of K2.

Signal utilisation Effects of signal failure

The clutch input speed signal … In case of failure of G182, the engine speed
is utilised as a substitute signal.
… is used for more precise clutch control. Microslip control and certain
adaptive adjustments will not be possible.
… is used for clutch adaptation, There will be loss of shift quality.
refer to page 27.
In the event of sporadic losses of signal,
… is used for microslip control; refer to page 27. fluctuations in engine speed can occur.

In all fault situations, no corrective action is taken,

rather an entry is made in the fault memory only
(without fault indication).

Dual-mass flywheel Outer plate carrier K1

Outer plate carrier K2 Main hub

Encoder disc
Output shaft 2

386_076
G509

G182 Encoder disc Encoder disc

Input shaft 2 Input shaft 1

68
Gearbox output speed sender 1 (2) G501 (G502)

Both senders are Hall senders and are integrated in the electronic module. The encoder disc is a sheet metal
part with a magnetised rubber ferrous metal coating.

Signal utilisation Effects of signal failure

– Measurement of the clutch output speed If either of the senders fails, the part-gearbox
for calculating the slip in question is shut down.
(microslip) of each clutch The gearbox starts the emergency program;
(G501 = K1, G502 = K2). refer to page 85.

– Utilisation for microslip regulation and Fault indication: yes

clutch adaptation: refer to page 27.

– Determination of the synchronisation

speed for gearshifts.

G501 G502

386_117

Note
The encoder discs must be kept clear of
magnetic fields.
Metal chips and swarf can impair the
function of the encoder discs.

69
 Gearbox control unit

Gearbox output speed sender 1 (2)

G195 (G196)

Both senders are Hall senders and are integrated Signal utilisation
in the electronic module. The encoder disc is a sheet
metal part with a magnetised rubber ferrous metal – Determining the vehicle speed for
coating. Senders G195 and G196 monitor the speed shift point selection and determination
of output shaft 2 and hence the gearbox output
speed. – Recognition of travel direction to verify
the plausibility of gear selections
The signal from G196 is utilised for detecting the (e.g. when reversing at > 10 kph,
direction of rotation of the gearbox, and hence for 1st gear cannot be selected)
differentiating between forward and reverse travel.
For further information, refer to SSP 228 Creep control function
(from page 68).
Effects of signal failure
One of the principal signals utilised for electronic
gearbox control is gearbox output speed.There The vehicle speed and travel direction signals
exists a defined relationship between gearbox from the powertrain CAN bus (ESP) are utilised
output speed and vehicle speed. as substitute signals.

Fault indication: yes

Electronic module

386_117

Sender arm of the electronic module

Encoder disc

G196 G195

386_079
G196 G195

70
Automatic gearbox hydraulic pressure
sender -1- (2) G193 (G194)

Both senders are located in the channel plate Signal utilisation

of the electronic module.
– Monitoring of the clutch pressure
G193 monitors the clutch pressure of clutch K1 of K1 and K2
(actual clutch pressure).
Adaptation of the main pressure
G194 monitors the clutch pressure of clutch K2
(actual clutch pressure). Effects of signal failure

The actual clutch pressure is continuously In case of signal failure or implausible signals,
compared to the nominal clutch pressure computed the part-gearbox in question is shut down and
by the gearbox control unit and checked for the relevant emergency program is activated.
plausibility. In case of deviations (malfunctions),
a safety shutdown of the part-gearbox is question Fault indication: yes
is initiated and the relevant emergency program
is activated; refer to "Safety shutdown" and
"Emergency program".

G193 G194

Channel plate

386_059

71
 Gearbox control unit

Gear selector travel sensor 1 (2, 3, 4) G487

(G488, G489, G490)

The gear selector travel sensors are Hall senders The travel sensors are assigned to the following
and are integrated in the electronic module. shift forks:
Gear selectors are hydraulically actuated shift forks;
refer to page 30.
In combination with permanent magnets mounted G487 – gear selector/shift fork 1 (1st/3rd gear)
on the shift forks, they generate a signal which G488 – gear selector/shift fork 2 (2nd/4thgear)
provides the control unit with information on the G489 – gear selector/shift fork 3 (6th/reverse)
position of each shift fork. G490 – gear selector/shift fork 4 (5th gear)

Signal utilisation

The exact position of the shift fork is important

for correct gear selection and selected gear status
recognition.
Care must also be taken to ensure that the various
shift forks do not adopt incorrect positions and
hence that no incorrect gearshifts executed.

Effects of signal failure

In case of failure of a travel sensor, the

part-gearbox concerned is shut down and
the relevant emergency program is activated.

Fault indication: yes G488

G487

G490

G489

72
 Note
To ensure the required positional determination
accuracy, the travel sensors and the shift forks must
be adapted by performing the basic setting procedure
(e.g. after replacement of the mechatronic module).

If basic setting is not performed, the vehicle will only

drive in 1st, 2nd and reverse gear. In this case, a fault
message indicating that basic setting has not been
carried out is stored in the fault memory.

Shift fork 2/4 Shift fork 3/1

386_111

Shift fork R/6 Shift fork N/5

73
 Gearbox control unit

Selector lever sensor system E313

The mechatronic control unit J743 receives

information on the selector lever position from the
selector lever sensor system E313.
The mechatronic control unit is integrated in the
gearshift mechanism.

E313 is an electronic component comprising

the sensors and a control unit which communicates
by means of the powertrain CAN data bus.
The selector lever sensor system E313 performs the
tasks of the previous multi-function switch F125. Gear selector of the Audi A3

The individual selector lever positions are

recognised by means of Hall sensors, which, for
safety reasons, are installed double to provide
redundancy.
Selector lever sensor
Information is transmitted between E313 system E313
and J743 by powertrain CAN bus.

Hall sensors for determining selector 386_082

lever positions P, R, N, D and S

Signal utilisation Effects of signal failure

Information on selector lever position is required Faults in the E313 manifest themselves in very
to implement the following functions: different ways. If it is not possible to clearly identify
the selector lever position, the start enabling signal
– Information on the driver input/driving condition is generated, but no power transmission is possible.
(forwards, reverse, neutral) for activation of the
gear selectors and clutches Fault indication: inverted flashing
– Control of the tiptronic function (not Audi TT 8N)
– Information on shift program "D" or S" The selector lever sensor system E313 has its own
– Starter inhibitor control diagnostic address word. Faults are transferred to
– P/N lock (Shift Lock) control the mechatronic control unit J743 and can be read
– Control of the reversing lights out here.
– Control of the selector lever position indicator in
the dash panel insert

Control of the LEDs according to the selector lever

position in the selector gate cover or in the display
unit.

74
tiptronic switch F189
Gearshift mechanism
Audi A3 (8P) and TT (8J)
F189 consists of three Hall sensors. They are
integrated in the selector lever sensor system.
F189 supplies the shift information required to
implement the tiptronic function.

The signals from F189 are evaluated by the

selector lever sensor system and transmitted Gate valve

to the mechatronic control unit by CAN message.

Gate valve

Gate valve

open

Permanent
magnet

Hall sensors 386_115

Legend

E313 Selector lever sensor system (selector lever)

F189 tiptronic switch (integrated in E313)
F319 Selector lever locked in position P switch
L101 Selector lever scale
N110 Selector lever lock solenoid
Y26 Selector lever position indicator unit

* refer to pages 14 and 60

P-signal*
Powertrain
CAN bus 386_083

75
 Gearbox control unit

Selector lever sensor system E313

for Audi TT (8N) Magnet carrier Permanent magnets on
the magnet carrier

The information on signal utilisation

and function on page 74 basically
applies to the selector lever sensor
system E313 in the Audi TT (8N).
The design and function of the
tiptronic switch F189 are different.

Hall sensors for the determination of

selector lever positions P, R, N, D and S

386_118

tiptronic switch F189

for Audi TT (8N)

In the Audi TT (8N), the tiptronic switch F189

consists of two components, the F189/a and
the F189/b.

tiptronic switch F189/a

F189/a is a mechanical micro-two-way switch

which is used for tiptronic gate detection. F189/b

386_125

F189/a

76
tiptronic switch F189/a

F189/b consists of Hall sensors and electronics for

the detection of selector lever positions Tip+ and Tip–.

F189/b

F189/a

Back of tiptronic switch F189/b

386_116

Magnet

Gate valve

Hall sensors

Function diagram of the gearshift mechanism

Audi TT (8N)

The information from F189/a and F189/b is

evaluated by the selector lever sensor system
and transmitted to the mechatronic control unit
by CAN message.

Legend

E313 Selector lever sensor system (selector lever)

F189/a tiptronic switch (tip gate signal)
F189/b tiptronic switch (Tip–/Tip+ signal)
L101 Selector lever display illumination
N110 Selector lever lock solenoid
Y26 Selector lever position indicator unit

Powertrain 386_084
CAN bus

77
 Gearbox functions

tiptronic steering wheel

In combination with the tiptronic steering wheel,
Note
the "tiptronic" function is also available in selector
lever position "D" or "S". The tiptronic shift paddles may, in
certain circumstances, be operated
The transition to tiptronic mode is made by unintentionally.
pressing either of the tiptronic shift paddles on the The driver often registers this as undefined
steering wheel (in selector lever position "D" or "S"). gearshifts or notices that for a certain
The system switches to tiptronic mode for approx. period time no gearshifts are made. In
8 seconds. Gears can be selected within the such cases, the gearbox control unit can
allowable engine speed ranges. be encoded in such a way that the tiptronic
It is possible to skip gears by pressing the steering wheel is only active when the
tiptronic button several times, e.g. to shift down selector lever is in the tiptronic gate.
from 6th to 3rd gear. Please consult the customer in regard
to this matter.
The system returns to normal automatic operation
approximately 8 seconds after the last tip shift
request.

Special feature: The countdown of 8 seconds until

return to normal automatic operation is halted as
long as it is determined that the vehicle is cornering
(transverse acceleration limit exceeded) or is in
overrun or is being driven at full throttle.
In vehicles from MY ‘06 or earlier, however, the
system returns from tiptronic mode to automatic
mode within 40 seconds at the latest.
In Audi vehicles from model year ‘07 or later,
the countdown is halted until one of the
aforementioned driving situations is present.

Function in the Audi A3 (8P):

The shift pulse from the tiptronic shift paddles

(earth signal) is evaluated by the multi-function
steering wheel control unit J453 and sent by LIN
data bus to the steering column electronics control
unit J527.

J527 sends the information by convenience CAN

bus to J533 (gateway). The data is transferred from
J533 to the powertrain CAN bus and thus made
available to mechatronic control unit J743.

386_085

78
Further variants of the tiptronic steering wheel in the Audi A3 (8P)

Audi A3 (8P) tiptronic steering wheel with multifunction

steering wheel

386_086

Audi TT (8N) tiptronic steering wheel without multifunction

steering wheel

386_087

Legend

E221 Operating unit in steering wheel LIN LIN single-wire bus system
E389 tiptronic switch in steering wheel 58PWM Pulse-width modulated dimming of the
E438 tiptronic switch (shift up) in steering wheel switch light
E439 tiptronic switch (shift down) in steering
wheel
F138 Coil spring Output signal
J453 Multi-function steering wheel control unit Input signal
J527 Steering column electronics control unit
J533 Data bus diagnostic interface (Gateway)
J743 Mechatronic control unit

79
 Gearbox functions

"Freeing vehicle by rocking

back and forth" and drive-
away in 2nd gear
As described previously under "gearshift sequence" In addition, the vehicle can be deliberately driven
on page 40, the vehicle is driven away in 2nd gear way in 2nd gear in order to reduce the driving
under certain conditions. power at the wheels on road surfaces with a low
The driver is not normally conscious of this frictional coefficient, e.g. in wintry road conditions.
function, because 1st gear is subsequently This makes drive-away easier, because the wheel
selected for acceleration. traction is not exceeded as quickly.

If vehicle is stuck fast, it can be dislodged by This function can be activated by moving the
rocking it back and forth by selecting "D" then "R" selector lever back and forth several times between
in rapid succession. In this situation, drive-away selector lever positions "R" and "D".
in selector lever position "D" is in 2nd gear. The vehicle subsequently drives away in 2nd gear.
The background to this is the gearshift sequence
described on page 40 at drive-away in "D" or "S".

Note
If the function is activated inadvertently
(e.g. while manoeuvring), the next drive-away
will, as described, be executed in 2nd gear.
This can prompt the following complaint:
"insufficient vehicle acceleration".

Launch Control Program

The Launch Control Program allows maximum * There is almost no load on the engine.
acceleration from a standing start. Clutch torque is approx. 1 Nm, i.e. the clutch
For this purpose, engine speed is set to pressure is low.
approx. 3200 rpm* before the starting clutch "Launch Control speed" is dependent on engine
is positively engaged. variant:
Engine torque and power transmission by the
clutch are balanced fully automatically. 3200 rpm for naturally aspirated petrol engines
2600 rpm for TFSI engines
The requirements for use of the "Launch Control 2000 rpm for TDI engines
Programme" are as follows:
** A brake pressure of at least 20 bar
• Vehicle speed 0 kph must be generated.

• Gearbox oil temperature > 30 °C

• Normal clutch temperature
• ESP or TCS switched OFF (at the ESP button,
ESP warning lamp "on") Note
• Selector lever position "S" or tiptronic Observe the safety instructions in
• Apply brake** (with left foot) the relevant operating instructions.
Remember to switch on the ESP again.
• Apply full throttle (engine runs at approx.
3200 rpm*)
The "Launch Control Program" is unavailable
with US spec vehicles.
As soon as the brake is released, the gearbox
In the Audi TT MY ‘07 (8J), the "Launch
control unit sets maximum acceleration.
Control Program" is also available in the US
spec model since TCS can be deactivated
separately from ESP in this vehicle.

80
S - sport program Downshifting with short
intermediate throttle
A performance oriented shift program is available
application between
to the driver in selector lever position "S".
When the gearbox control unit receives the gearshifts
information "selector lever position S", the shift (petrol engines only)
characteristics are biased towards higher engine
speeds. The result is improved driving dynamics. To underscore the sporty character of the 02E
gearbox, overrun downshifts are executed in the
S program or in the tiptronic program with short
intermediate throttle application between
gearshifts.

The engine speed is actively increased to

synchronisation speed through the engine
management system. The clutches are opened
temporarily.

The result is faster downshifts and a sporty driving

feel. Load reversal when downshifting is positively
influenced.

Shift characteristic D/S

D Selector lever position = Drive

Throttle-valve angle in %

S Selector lever position = sport program

Gearbox output speed in rpm

Software Shift Lock

The Software Shift Lock function is a safety feature. The Software Shift Lock can be activated as follows:
If the shift lock solenoid N110 cannot lock the
selector lever in position "P" or "N", this safety The engine runs at idle. Apply the brake and move
function prevents unintentional drive-away by the selector lever far enough out of "P" so that the
selecting a gear while the engine is running. "P" position is still indicated, but the locking bolt
can no longer engage after the brake is released.
The Software Shift Lock may be activated Release the brake and move the selector lever to
inadvertently by the driver. In this case, the "R", "D" or "S".
complaint will usually be: "Vehicle sporadically has The vehicle has no drive. To restore drive, the brake
no drive". When the driver applies the brake again, must be applied and released.
the function is deactivated and vehicle drive is
restored. The fault indicator in the dash panel insert flashes
while the "Software Shift Lock" function is active;
refer to page 84.

81
 Gearbox functions

Starter inhibitor/starter control

Audi A3 (8P) and Audi TT (8J)

Reference
For further information on the terminal
control system, refer to SSP 312 from
page 16.

P/N signal
386_091

Legend

E313 Selector lever sensor system K K-wire (diagnostics)

(selector lever) L101 Selector lever display illumination
F189 tiptronic switch M17 Reversing light bulb, right
J519 Onboard power supply control unit Y26 Selector lever position indicator unit
J533 Data bus diagnostic interface (Gateway)
J682 Terminal 50 voltage supply relay
J743 Mechatronic control unit

The "starter inhibitor" function allows activation Control unit J743 sends, via a discrete line, a P/N
of the starter (terminal 50) only in selector lever signal (start enabling signal from gearbox, earth)
position "P" or "N". to control unit J519.
Once all signals required for starting have been
Terminal 50 is activated by relay J682 which received by J519, the control unit activates relay
in turn is activated by onboard power supply J682.
control unit J519. For the purpose of diagnosis of the discrete line
For this purpose, control unit J519 requires, in for the P/N signal, the selector lever position
addition to the signals from the ignition lock and information is sent concurrently to J519 by CAN
the engine control unit, the information that the data bus.
selector lever is in position "P" or "N". Information route: E313 (powertrain CAN bus) >
J743 (powertrain CAN bus) > J533 (convenience
The selector lever sensor system E313 determines CAN bus) > J519.
the selector lever position (also refer to page 74)
and sends the information by powertrain CAN bus In the event of disruption in the power supply
to the mechatronic control unit J743. to J743/E313, the starting enable signal is not
generated at the P/N signal or at the CAN
connection.

82
Special features of the Activation of the
starter inhibitor reversing lights
At gearbox oil temperatures below -10 °C the start The reversing lights are controlled by control unit
enabling signal is only generated in selector lever J519 (refer to function diagram 386_091 on page 82).
position "P". For this purpose, J519 receives the information
"selector lever position R" by CAN information
Extremely low temperatures produces a high drag exchange.
torque in the clutches. Information route: E313 (powertrain CAN bus) > J743
This in turn produces unwanted driving torque at (powertrain CAN bus) > J533 (convenience CAN bus)
the wheels, causing the vehicle to creep as of a > J519.
certain torque.
To prevent this the engine can only be started in
such situations in selector lever position "P". The
parking lock holds the vehicle securely in place.

Starter inhibitor/starter control,

activation of the reversing
lights in the Audi TT (8N)
Legend
In the Audi TT Type 8N the starter is activated via
E313 Selector lever sensor system (selector lever)
relay J207 and the reversing lights are activated
F189/a tiptronic switch (tip gate signal)
directly by the mechatronic control unit J743 by
F189/b tiptronic switch (Tip–/Tip+ signal)
means of relay J219.
J207 Starter inhibitor relay
The selector lever sensor system E313 supplies the
J219 Reversing light relay
information on selector lever position, as described
J743 Mechatronic control unit
previously.
L101 Selector lever display illumination
N110 Selector lever lock solenoid
Likewise, at temperatures below -10 °C, the start
K K-wire (diagnostics)
enabling signal is only generated in selector lever
V Road speed signal
position "P".
Y26 Selector lever position indicator unit
Refer to "Special features of the starter inhibitor".

386_092

83
 Gearbox functions

Selector lever position,

gear and fault display in the
dash panel insert
In addition to the selector lever position and gear
indicator for automatic and tiptronic mode, the
display is used for the visualisation of faults and
protective functions (e.g. clutch overload
protection, page 26).

Depending on the effect on the gearbox and driving

safety, faults and protective functions are indicated
to the driver by inversion of the selector lever
position indicator colours.

386_127

Automatic mode tiptronic mode

Displays in normal operation

Active gear indication

(8P MY 05 or later and 8J)

A distinction is made between the following additional displays:

The self-diagnostics have diagnosed a fault in the

Fault indication system which activates the emergency program or
(inverted colours,
static) a substitute program, or is only indicated.
The driver must bring the vehicle immediately to a
service partner workshop in order to have the fault
corrected.
Warning displays

Software Shift Lock

Depending on which of the three selector lever

positions is engaged when the Software Shift Lock
is activated, the corresponding selector lever
position is indicated by a flashing light.

Clutch overload protection

When clutch overload protection is active,

the selector lever position indicator alternates
between the display modes shown (frequency 1 Hz).

The warning displays signal to the driver to abort and retry the current operation (refer to description of
overload protection or Software Shift Lock).

84
Emergency program
Faults in the system or safety functions are detected
Note
by the self-diagnostics. Depending on what effect
the system fault in question has on motoring safety, In emergency mode, reversing is not
the appropriate emergency programs are made possible for technical reasons.
available.
Emergency operation with part-gearbox 1:
Faults are indicated by the selector lever position Reverse (R) gear belongs mechanically
indicator. to part-gearbox 1, but is engaged by the
hydraulic safety circuit of part-gearbox 2.
In the case of defined system faults, the part- Reversing is not possible because the
gearbox in question is deactivated by the safety latter is deactivated.
shutdown function (refer to page 28), and the
gearbox control unit activates the relevant Emergency operation with part-gearbox 2:
emergency program. Reverse (R) gear can be selected, but it
is gaged positively via clutch K1
1. Part-gearbox 1 OK, part-gearbox 2 shut down: (part-gearbox 1).
Reversing is not possible because the
Only gears 1 and 3 are selected hydraulic safety circuit of the part-gearbox
(with interruption in tractive power). is deactivated.
Refer to the hydraulic diagram on page 28.
Reversing is not possible.

2. Part-gearbox 2 OK, part-gearbox 1 deactivated:

Only 2nd gear is selected; in this case,

it is used for drive-away.

Reversing is not possible. The following generally applies to the 02E gearbox:

Without electrical power and oil pressure,

no traction (or emergency operation) is possible.

Towing Reasons for towing speed limit:

Example:
In the event that a vehicle with S tronic has to be
A vehicle breaks down in 1st gear.
towed, the following restrictions apply:
The clutches are open because the system is
• The selector lever must be in the "N" position. pressureless. The wheels drive the input shafts
• A max. towing speed of 50 kph must not be and clutches via the output shafts.
exceeded. If the vehicle is towed too quickly, the shafts and
gears will reach engine speeds for which they are
• A max. towing distance of 50 km must not be not designed. As mentioned previously, there is no
exceeded. lubrication, which is why there is also a limit on
towing distance.
When towing (engine at standstill) the vehicle, the
oil pump is not driven and there is no lubrication of A further example illustrates the problem:
rotating parts. In selector lever position "P" or "N" reverse (R) gear
Failure to observe the above restrictions will result and 2nd gear are always selected. When a vehicle is
in serious gearbox damage. towed in this gear configuration, this will result in a
high speed differential between the input shafts
and the clutches, which can result in terminal
gearbox damage if the max. allowable towing
speed is exceeded.

85
 Index

A G
Activation of the reversing lights . . . . . . . . . . . . . 83 G85 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 65
All-wheel drive - bevel box . . . . . . . . . . . . . 17, 44, 45 G93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
All-wheel drive - power distribution . . . . . . . . . . . 44 G182 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
G193 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
G194 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
B G195 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
G196 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Bevel box . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 44, 45 G487 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
G488 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
G489 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
C G490 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
G501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
CAN information exchange G502 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Audi A3 (8P) /Audi TT (8J) . . . . . . . . . . . . . . . . . 62 G509 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
CAN information exchange Audi TT (8N) . . . . . . . 64 G510 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Clutch control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Gearbox concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Clutch control adaptation . . . . . . . . . . . . . . . . . . . 27 Gearbox control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Clutch cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Gearbox functions . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Clutch functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Gearbox input speed sender . . . . . . . . . . . . . . . . . . 68
Clutch K1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 18 Gearbox oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Clutch K2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 18 Gearbox oil (ATF) temperature sender . . . . . . . . . . 66
Clutch pressure . . . . . . . . . . . . . . . . . . . . . . 25, 56, 71 Gearbox output speed sender . . . . . . . . . . . . . . . . . 70
Control pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Gearbox periphery . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cooling oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 25 Gearbox subassemblies . . . . . . . . . . . . . . . . . . . . . . 16
Creep control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Gear indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Gear selector travel sensor . . . . . . . . . . . . . . . . . . . 72
Gearshift mechanisms . . . . . . . . . . . . . . . . . . . . 10, 11
D Gearshift sequence . . . . . . . . . . . . . . . . . . . . . . 40, 41

Differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Direct shift gearbox . . . . . . . . . . . . . . . . . . . . . . 4, 5, 9
Dislodging vehicle by rocking back and forth . . . 80
H
Downshifting with short intermediate Haldex coupling . . . . . . . . . . . . . . . . . . . . . . . . . 44, 45
throttle application between gearshifts . . . . . 81 Hydraulic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Drive-away . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Hydraulic pressure sender . . . . . . . . . . . . . . . . . . . 71
Drive-away in 2nd gear . . . . . . . . . . . . . . . . . . . . . . 80
Drive shaft speed sender . . . . . . . . . . . . . . . . . . . . 69
Dual-mass flywheel . . . . . . . . . . . . . . . . . . . . . . . . . 16
Dynamic pressure equalisation . . . . . . . . . . . . . . . 21
I
Ignition key withdrawal lock . . . . . . . . . . . . 10, 13-15
Input shaft 1, 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17
E Interruption in tractive power . . . . . . . . . . . . . . . . 5-7

E221 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
E313 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74, 76
E389 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
J
E438 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 J104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 65
E439 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 J207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61, 83
Electro-hydraulic control unit . . . . . . . . . . . . . . . . 52 J219 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61, 83
Electronic module . . . . . . . . . . . . . . . . . . . . . . . . . . 58 J220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Emergency (limp-home) program . . . . . . . . . . . . . 85 J285 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 64
Emergency release . . . . . . . . . . . . . . . . . . . . . . . . . 12 J345 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
J453 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 78, 79
J519 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 82, 83
F J527
J533
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15
. . . . . . . . . . . . . . . . . . . . . . . . . . 14, 62, 78, 82, 83
F125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 J682 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
F138 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 J743 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
F189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-77
F319 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 75
Fault indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Final drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17
K
Function diagram Audi A3 (8P)/Audi TT (8J) . . . . . 60 Kick-down . . . . . . . . . . . . . . . . . . . . . . . SSP291 S. 62
Function diagram Audi TT (8N) . . . . . . . . . . . . . . . 61

86
L R
L101 . . . . . . . . . . . . . . . . . . . . . . . . . 11, 75, 77, 82, 83 Reverse shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17
Launch Control Program . . . . . . . . . . . . . . . . . . . . . 80
Lube oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
S
M Safety shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 8
M17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Sectional view of gearbox . . . . . . . . . . . . . . . . . . . . 16
Main pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 46, 56 Selector lever position indicator . . . . . . . . . . . . 74, 84
Manual gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Selector lever sensor system . . . . . . . . . . . . . . 74, 76
Manual gearbox control (hydraulic) . . . . . . . . . . . 36 Selector mechanism . . . . . . . . . . . . . . . . . . . . . . 30, 31
Mechatronic control unit . . . . . . . . . . . . . . . . . . . . 58 Sensors (senders) . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Mechatronic module . . . . . . . . . . . . . . . . . . . . . 17, 50 shift by wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Microslip control . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Shift Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 12
Multi-plate clutch oil temperature sender . . . . . . 67 Shift pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 36
Multiple shifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Software Shift Lock . . . . . . . . . . . . . . . . . . . . . . . . . 81
Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36, 37 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
S – sport program . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Starter inhibitor/starter control . . . . . . . . . . . . . . . 82
N S tronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 9
Suppliers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
N88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36, 48, 54 Synchromesh - manual gearbox . . . . . . . . . . . . . . . 35
N89 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36, 48, 54, 55
N90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36, 48, 54
N91 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36, 48, 54
N92 . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-39, 48, 54, 55
T
N110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14 Temperature sensor in control unit . . . . . . . . . . . . 66
N215 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48, 55, 56 tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74-79
N216 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48, 55, 56 tiptronic steering wheel . . . . . . . . . . . . . . . . . . 78, 79
N217 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48, 55, 56 tiptronic switch . . . . . . . . . . . . . . . . . . . . . . . 75, 76, 77
N218 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48, 55, 57 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
N233 . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29, 48, 55, 57 Twin clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 19
N371 . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29, 48, 55, 57 Twin clutch control (hydraulic) . . . . . . . . . . . . . . . . 24
N376 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15

O V
Valves of the electro-hydraulic control unit . . . . . 54
Oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 46
Oil supply - gearbox . . . . . . . . . . . . . . . . . . . . . . . . 46
Oil supply - twin clutch . . . . . . . . . . . . . . . . . . . . . . 20
Output shaft 1, 2 . . . . . . . . . . . . . . . . . . . . . . . . 16, 17
W
Overlapping operation . . . . . . . . . . . . . . . . . . . 23, 41 Warning shudder . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Overload protection . . . . . . . . . . . . . . . . . . . . . . . . 26

P Y
Y26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Parking lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Part-gearbox 1, 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Patent .................................. 6
P/N lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13
Position of the shafts in the gearbox . . . . . . . . . . 17
Power flow in gearbox . . . . . . . . . . . . . . . . . . . . . . 32
Power flow in twin clutch . . . . . . . . . . . . . . . . . . . . 18
Power flow transition . . . . . . . . . . . . . . . . . . . . 22, 23
Pressure control valves . . . . . . . . . . . . . . . . . . . . 55-57
Pressure oil supply . . . . . . . . . . . . . . . . . . . . . . . . . 20
Pump shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

87
 386
Vorsprung durch Technik www.audi.co.uk Service Training

6-speed twin-clutch gearbox 02E (S tronic)

Self-Study Programme 386

All rights reserved. Technical

specifications subject to
change without notice.

Copyright
AUDI AG
I/VK-35
[email protected]
Fax +49-841/89-36367

AUDI AG
D-85045 Ingolstadt
Technical status: 10/06

Printed in Germany
A06.5S00.31.20