Scribd
Upload
224 views

Written Test and Performance Test

1. Prepare the necessary tools for installing network cables such as crimping tools, cable testers, and cable clamps. 2. Configure the network settings of devices like routers, wireless access points, and repeaters. 3. Install and terminate the network cables to interconnect all the devices based on the network design. 4. Inspect and test the fully installed computer network to ensure it meets performance standards and is functioning properly.

Uploaded by

noe
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
224 views

Written Test and Performance Test

1. Prepare the necessary tools for installing network cables such as crimping tools, cable testers, and cable clamps. 2. Configure the network settings of devices like routers, wireless access points, and repeaters. 3. Install and terminate the network cables to interconnect all the devices based on the network design. 4. Inspect and test the fully installed computer network to ensure it meets performance standards and is functioning properly.

Uploaded by

noe
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

WRITTEN TEST

I. TRUE OR FALSE: Tell whether the statement about Network Design is true
or false. Write (T) if the statement is True and (F) if the statement is False.
Write your answer on a separate sheet.

___________1. Tree topology has a root node and all other nodes are connected
to it forming a hierarchy.
___________2. Hybrid topology is two different types of topologies which is a
mixture of two or more topologies.
___________3. Mesh topology is a point-to-point connection to other nodes or
devices.
___________ 4. In flooding, the nodes have a routing logic, as per the network
requirements.
___________5. In routing, the same data is transmitted to all the network nodes,
hence no routing logic is required.
___________6. A systematic cleaning effort for the entire work area will ensure
the safety of everyone involved.
___________7. Fiber optic cables have many tiny glass particles that are
dislodged when the cables are moved for any reason.
___________8. A simple drink of water can carry glass shards into the throat
and down the esophagus where they can cause
lacerations and internal hemorrhages.
___________9. There are reasons to look through a fiber cable, but care must
be exercised to ensure that there is visible light coming
through the cable.
___________10. Glass shards cannot lodge in the surface of the eye and
cause lacerations.

II. MULTIPLE CHOICE: Read and understand each question. Write your
answer on a separate sheet.

11. It is an electronic device used to verify the electrical connections in a signal


cable or other wired assembly.
a. crimping tool
b. terminal box
c. digital multi-meter
d. LAN tester
12. It is a type of connector commonly used for Ethernet networking.
a. cables
b. pliers
c. rj45
d. screwdriver
13. These are mechanical devices or clips that define a route for one or more
cables along a building wall or within instrumentation, control or other
type of electrical enclosure.
a. clamps
b. cables
c. wire stripper
d. terminal box
14. It is a screwdriver with a wedge-shaped flat tip, used to tighten or loosen
screws that have a straight, linear notch in their heads.
a. flat-head screwdrivers
b. star screwdrivers
c. both a and b
d. none of the above
15. It is a device used to conjoin two pieces of metal by deforming one or both
of them in a way that causes them to hold each other. The result of the
tool's work is called a crimp.
a. wire stripper
b. crimping tool
c. pliers
d. terminal box

II. IDENTIFICATION: Read and understand each question. Write your answer
on a separate sheet.

_______________________ 16. It has an opposite Pin assignments on each end of


the cable.

_______________________ 17. These are used to connect and transfer data and
information between computers, routers, switches, and storage area networks.

_______________________18. These are very much like Straight-Through cables,


the lines are crossed and they are at the opposite positions on either end of the
cable.

_______________________19. It refers to cables that have the same pin


assignments on each end of the cable.

_______________________20. It is identifiable by its hinged or sliding cover that


fully encloses the cables within the channel.
ANSWER KEY

I. TRUE OR FALSE

1. T
2. T
3. T
4. F
5. F
6. T
7. T
8. T
9. T
10. F

II. MULTIPLE CHOICE

11. d
12. c
13. a
14. a
15. b

III. IDENTIFICATION

16. rollover wire cables


17. network cables
18. crossover wired cables
19. straight-through cable
20. latching raceway
Performance Test

Specific Instruction for the Candidate

Qualification Computer System Servicing NCII

Unit of Competency Set-up Computer Networks

General Instruction:

Given the necessary tools, materials, and equipment, you are required to
set-up computer networks with accepted institutional/ industry standard.

(Allotted time: 40 hrs.)

Specific Instruction:

1. Prepare all the tools for network cables installation

2.

2. Set network configuration

3. Set router/Wi-Fi/ wireless access point/repeater configuration

4. Inspect and test the configured computer networks

You might also like