Water Softeners Overview and Sizing Information

About Water Softeners

Hard Water contains dissolved minerals in the form of Calcium (Ca),
Magnesium (Mg), and Iron (Fe). Removal of these minerals is
accomplished by softening the water through an ion exchange process.
As the water flows through the mineral tank, the dissolved minerals
become attached to the resin, creating soft water. Over a period of time
the resin will become exhausted, and the softener will regenerate using a
brine solution produced from the salt in the brine tank.

Advantages to Using Water Softeners

 Prevents Hard Water Scale
 Provides Excellent Scale Prevention Pretreatment for Reverse Osmosis
Systems
 Prevents Staining on Bathroom & Kitchen Fixtures as well as Dishes,
Dishwasher, Washing Machine & Clothes
 Significantly Reduces Soap and Cleaning Product Consumption
 Reduces Water Heating Costs
 Prolongs Life of RO Membranes, Water Heaters, Icemakers, Dishwashers,
Coffeemakers & Plumbing Fixtures

Sizing and Selection Information

Step 1: Calculate Total Hardness as GPG
Usually chemical analyses report calcium (Ca) and magnesium (Mg) in terms of parts per million (ppm) as
calcium carbonate (CaCO3). However, in some cases, the analysis is reported in terms of the elements
themselves. If this is the case, proceed as follows:

Calcium (as Ca)_________ × 2.50 = _________ppm Ca as CaCO3. (A)

Magnesium (as Mg) _________× 4.10 = _________ppm Mg as CaCO3. (B)

A _________ + B_________ = _____________Total Hardness PPM as CaCO3

Total Hardness PPM as CaCO3 _________ ÷ 17.1 = _________ GPG as CaCO3.

Step 2: Calculate Cubic Feet of Resin Required

_________ Gallons per Day × _________Total Hardness (GPG) = _________ Grains per Day

_________ Grains per Day ÷ 30,000 = _________ Cubic Feet of Resin Required

Select the appropriate softener based on the volume of resin.

When between sizes, it is recommended to select the next size up.

Note: The above calculations are based on daily regeneration and maximum resin capacity. Regeneration based on 15
lbs. of salt per cubic foot of resin.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-1
Single Water Softeners – Time-Based Regeneration
Single Water Softeners with a timed valve are programmed to regenerate at a specific time of day. They are
usually scheduled to regenerate at 2am, when the demands for soft water are expected to be very low. These
can be set to regenerate after a specific number of days, or on certain days of the week.

Features and Specifications of AMI Water Softeners

 High quality, high capacity softening resin which complies with
FDA regulations for potable water applications and is NSF/ANSI-61
Certified for material safety
 Fully automated with state of the art electronic control valve
featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day, and days until next regeneration
(21+” dia. Units also display current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile
memory
 12-volt output AC Adapter provides safe and easy installation (20-volt with optional SS jacket
output for 42” & 48”dia. units)
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum
operating temperature (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Regeneration: Time Clock Delayed (Pressure differential or PLC-controlled options are available upon request.)

Model No.* Flow Rate** (gpm) Backwash Volume of Resin (cu.ft.) Resin Tank Brine Valve & Approx.
5gpm/ft2 15gpm/ft2 Flow** (gpm) Softening Resin Total (Incl. (Dia”×H”) Tank In/Out Shipping
(only) Underbed) (Dia”×H”) Conn. Wt. (lbs)
W-S744ETS 1 4 1.3 0.50 0.60 7×44 18×33 1” 100
W-S844ETS 2 5 1.7 0.60 0.70 8×44 18×33 1” 105
W-S940ETS 2 6 2.2 0.75 0.85 9×40 18×40 1” 115
W-S1054ETS 2 7 2.7 1.25 1.45 10×54 18×40 1” 150
W-S1252ETS 4 12 4.2 1.75 2.05 12×52 18×40 1” 190
W-S1354ETS 4 14 5.3 2.00 2.30 13×54 18×40 1” 225
W-S1465ETS 5 16 5.3 3.00 3.50 14×65 24×41 1” 335
W-S1665ETS 7 21 6.5 3.50 4.00 16×65 24×41 1” 385
W-S2162ETS 13 36 13 6.00 7.00 21×62 30×48 1.5” 645
W-S2472ETS 15 47 15 8.00 10.0 24×72 39×48 1.5” 950
W-S3072ETS 24 74 25 12.5 16.5 30×72 39×48 2” 1,535
W-S3672ETS 35 95 35 17.0 22.0 36×72 39×60 2” 1,950
W-S4272ETS 48 144 50 23.0 30.0 42×72 42×60 3” 2,950
W-S4872ETS 60 188 60 30.0 43.6 48×72 60×60 3” 4,360

Notes
* Softeners are available with USA or European style plugs and voltages. Please add
the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-S744ETS-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. For relatively
clean water, you may go up to design criteria of 15 gpm per sq. ft. Backwash flow
rate based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right)
are available upon request. AMI Water Softeners are offered standard with new state
of the art electronic programmable valves, but may be ordered with
electromechanical Fleck valve heads upon request.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-2
Single Water Softeners – Meter-Based Regeneration
Metered Water Softeners regenerate based on your water usage. Like the timered softeners, these can be programmed to
regenerate at a certain time during the day, but instead of regenerating on a specific day as a timered softener does, the
metered softener does not schedule regeneration until the specified volume of water has passed through the softener.
These units can save water by preventing unnecessary regenerations since it does not regenerate until the resin is near its
capacity.
Features & Specifications
 High quality, high capacity softening resin which complies with FDA
regulations for potable water applications and is NSF/ANSI-61 Certified for
material safety
 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next regeneration
(21+” dia. Units also display current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile
memory
 12-volt output AC Adapter provides safe and easy installation (20-volt
output for 42” & 48”dia. units)
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum
with optional SS jacket
operating pressure and 120°F maximum operating temperature. (Optional
stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Regeneration: Meter Delayed
Volume of Resin Valve & Approx.
Flow Rate** (gpm) Backwash Resin Tank Brine Tank
Model No.* (cu.ft.) In/Out Shipping
Flow** (gpm) Softening Total (Incl. (dia”×H”) (dia”×H”)
Wt. (lbs)
5gpm/ft2 15gpm/ft2
Resin (only) Underbed) Conn.
W-S744EMS 1 4 1.3 0.50 0.60 7×44 18×33 1” 100
W-S844SEMS 2 5 1.7 0.60 0.70 8×44 18×33 1” 105
W-S940EMS 2 6 2.2 0.75 0.85 9×40 18×40 1” 115
W-S1054EMS 2 7 2.7 1.25 1.45 10×54 18×40 1” 150
W-S1252EMS 4 12 4.2 1.75 2.05 12×52 18×40 1” 190
W-S1354EMS 4 14 5.3 2.00 2.30 13×54 18×40 1” 225
W-S1465EMS 5 16 5.3 3.00 3.50 14×65 24×41 1” 335
W-S1665EMS 7 21 6.5 3.50 4.00 16×65 24×41 1” 385
W-S2162EMS 13 36 13 6.00 7.00 21×62 30×48 1.5” 645
W-S2472EMS 15 47 15 8.00 10.0 24×72 39×48 1.5” 950
W-S3072EMS 24 74 25 12.5 16.5 30×72 39×48 2” 1,535
W-S3672EMS 35 95 35 17.0 22.0 36×72 39×60 2” 1,950
W-S4272EMS 48 144 50 23.0 30.0 42×72 42×60 3” 2,950
W-S4872EMS 60 188 60 30.0 43.6 48×72 60×60 3” 4,360

Notes
* Softeners are available with USA or European style plugs and voltages. Please add
the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-S744EMS-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. For relatively clean
water, you may go up to design criteria of 15 gpm per sq. ft. Backwash flow rate
based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right) are
available upon request. AMI Water Softeners are offered standard with new state of
the art electronic programmable valves, but may be ordered with electromechanical
Fleck valve heads upon request.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-3
Twin Alternating Water Softeners
About Twin Alternating Water Softeners
Twin softeners are ideal for situations where uninterrupted flow of soft
water is a must. One resin tank is always in service, while the other tank
is in standby. When the meter determines that the resin is near its
capacity, it will switch the tank in standby to be in service, and the tank
containing the exhausted resin will begin regeneration and wait in
standby until the other tank is ready for regeneration.
Features & Specifications
 High quality, high capacity softening resin which complies with FDA
regulations for potable water applications and is NSF/ANSI-61
Certified for material safety
 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next regeneration (21+” dia. Units also display current flow rate, and total
volume used)
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile memory
 12-volt output AC Adapter provides safe and easy installation (20-volt output for 42” & 48”dia. units)
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum operating
temperature. (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Regeneration: Meter Immediate (Pressure differential options are available upon request.)

Flow Rate** Volume of Resin

Valve &
(GPM) Backwash (Cu. Ft.) Resin Tank Brine Approx.
In/Out
Model No.* 5gpm 15gpm Flow** Softening Resin Total (2) Tank Shipping Wt.
Conn.
per ft² per ft² (GPM) (Only) (Incl. Underbed) (Dia”×H”) (Dia”×H”) (lbs)
Per Tank Total Per Tank Total
W-S744EMT 1 4 1.3 0.50 1.00 0.60 1.2 7×44 18×33 1” 160
W-S844EMT 2 5 1.7 0.60 1.20 0.70 1.4 8×44 18×33 1” 170
W-S940EMT 2 6 2.2 0.75 1.50 0.85 1.7 9×40 18×40 1” 190
W-S1054EMT 2 7 2.7 1.25 2.50 1.45 2.9 10×54 18×40 1” 265
W-S1252EMT 4 12 4.2 1.75 3.50 2.05 4.1 12×52 18×40 1” 340
W-S1354EMT 4 14 5.3 2.00 4.00 2.30 4.6 13×54 18×40 1” 415
W-S1465EMT 5 16 5.3 3.00 6.00 3.50 7.0 14×65 24×41 1” 610
W-S1665EMT 7 21 6.5 3.50 7.00 4.00 8.0 16×65 24×41 1” 705
W-S2162EMT 13 36 13 6.00 12.0 7.00 14.0 21×62 30×48 1.5” 1,185
W-S2472EMT 15 47 15 8.00 16.0 10.0 20.0 24×72 39×48 1.5” 1,760
W-S3072EMT 24 74 25 12.5 25.0 16.5 33.0 30×72 39×48 2” 2,925
W-S3672EMT 35 95 35 17.0 34.0 22.0 44.0 36×72 39×60 2” 3,760
W-S4272EMT 48 144 50 23.0 46.0 30.0 60.0 42×72 42×60 3” 5,730
W-S4872EMT 60 188 60 30.0 60.0 43.6 87.2 48×72 60×60 3” 8,520

Notes
* Softeners are available with USA or European style plugs and voltages. Please add
the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-S744EMT-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. For relatively
clean water, you may go up to design criteria of 15 gpm per sq. ft. Backwash flow
rate based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right)
are available upon request. AMI Water Softeners are offered standard with new
state of the art electronic programmable valves, but may be ordered with
electromechanical Fleck valve heads upon request.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-4
Carbon Filters with Automatic Backwash
About Carbon Filters
These filters are used to reduce chlorine, organics, color, tannin, and objectionable tastes and
odors from water. Automatic backwashing system removes the trapped contaminants within
the filter bed and washes them down the drain. Carbon filtration significantly reduces the
following contaminants:
 Chlorine & Chlorine By-Products such as Trihalomethanes (THMs)
 Bad Tastes and Odors
 Turbidity
 Herbicides, Pesticides & Insecticides
 Volatile Organic Chemicals (VOCs)

Features and Specifications of AMI Carbon Filters

 High quality liquid phase bituminous coal base carbon meets ANSI/NSF Standard 61 and Food
Chemicals Codex Standards for drinking water applications.
(Carbon filters using California Prop. 65 tested coconut shell carbon for CA drinking water applications
are available upon request.)
 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next backwash (21+” dia. units also display
current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile memory
 12-volt output AC Adapter provides safe and easy installation (20-volt output for 42” & 48”dia. units)
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum operating
temperature. (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Backwash: Time Clock Delayed (Metered, pressure-differential and PLC-controlled options are available upon request.)
Model No.* Flow Rate** (GPM) Backwash Volume of Media (ft3) Approx.
Resin Tank Valve In/Out
Flow** Carbon Total (Incl. Shipping Wt.
5gpm/ft2 15gpm/ft2 (Dia”×H”) Size Conn. (lbs)
(GPM) (Only) Underbed)
W-G744ET 1 4 2.2 0.50 0.60 7×44 1” 1” 55
W-G844ET 2 5 2.7 0.60 0.70 8×44 1” 1” 60
W-G940ET 2 6 3.2 0.75 0.85 9×40 1” 1” 65
W-G1054ET 2 7 4.2 1.25 1.45 10×54 1” 1” 90
W-G1252ET 4 12 6.5 1.75 2.05 12×52 1” 1” 115
W-G1354ET 4 14 7.5 2.00 2.30 13×54 1” 1” 145
W-G1465ET 5 16 7.5 3.00 3.50 14×65 1” 1” 205
W-G1665ET 7 21 15 3.50 4.00 16×65 1” 1” 240
W-G2162ET 13 36 25 6.00 7.00 21×62 1.5” 1.5” 415
W-G2472ET 15 47 35 8.00 10.0 24×72 1.5” 1.5” 640
W-G3072ET 24 74 55 12.5 16.5 30×72 2” 2” 1115
W-G3672ET 35 106 75 17.0 22.0 36×72 2” 2” 1420
W-G4272ET 48 144 100 23.0 30.0 42×72 3” 3” 2270
W-G4872ET 60 188 120 30.0 43.6 48×72 3” 3” 3325
Notes
* Carbon filters are available with USA or European style plugs and voltages. Please
add the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-G744ET-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. For relatively clean
water, you may go up to design criteria of 15 gpm per sq. ft. Backwash flow rate
based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right) are
available upon request. AMI carbon filters are offered standard with electronic
programmable valves, but may be ordered with Fleck valve heads upon request.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-5
Multi-Media Filters for Sediment Removal
About Multi-Media Filters
These filters contain several types of media and gravel under-bedding. Multi-media filtration is
a proven design concept; the coarse media layers in the top of the tank trap large particles
and successively smaller particles are trapped in the finer layers of media deeper in the bed.
The result is a highly efficient filtering since removal takes place throughout the entire bed.
Multi-Media depth filters typically remove particles 5-15 microns in size or larger. All media
included in our filters are carefully selected according to particle size, so the media retains its
stratification during backwash and rinse. Automatic backwashing system removes the
trapped contaminants within the filter bed and washes them down the drain.
Features and Specifications of AMI Multi-Media Filters
 Filtration media classified by Underwriters Laboratories Inc.® in Accordance with Standard
ANSI/NSF 61.
 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next backwash (21+” dia. units also
display current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile memory
 12-volt output AC Adapter provides safe and easy installation (20-volt output for 42” &
48”dia. units)

 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum operating
temperature. (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Backwash: Time Clock Delayed (Metered, pressure-differential and PLC-controlled options are available upon request.)

Model No.* Flow Rate** (GPM) Backwash Volume of Media (ft3) Approx.
Resin Tank Valve In/Out
Flow** Filtration Total (Incl. Shipping Wt.
5gpm/ft2 15gpm/ft2 (Dia”×H”) Size Conn. (lbs)
(GPM) (Only) Underbed)
W-MB744ET 1 4 4.2 0.50 0.60 7×44 1” 1” 80
W-MB844ET 2 5 5.3 0.60 0.70 8×44 1” 1” 90
W-MB940ET 2 6 6.5 0.75 0.85 9×40 1” 1” 100
W-MB1054ET 2 7 7.5 1.25 1.45 10×54 1” 1” 150
W-MB1252ET 4 12 11 1.75 2.05 12×52 1” 1” 200
W-MB1354ET 4 14 15 2.00 2.30 13×54 1” 1” 250
W-MB1465ET 5 16 15 3.00 3.50 14×65 1” 1” 365
W-MB1665ET 7 21 20 3.50 4.00 16×65 1” 1” 425
W-MB2162ET 13 36 35 6.00 7.00 21×62 1.5” 1.5” 730
W-MB2472ET 15 47 45 8.00 10.0 24×72 1.5” 1.5” 1,060
W-MB3072ET 24 74 75 12.5 16.5 30×72 2” 2” 1,755
W-MB3672ET 35 106 105 17.0 22.0 36×72 2” 2” 2,280
W-MB4272ET 48 144 140 23.0 30.0 42×72 3” 3” 3,445
W-MB4872ET 60 180 175 30.0 43.6 48×72 3” 3” 5,050

Notes
* Media filters are available with USA or European style plugs and voltages. Please
add the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-MB744ET-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. For relatively
clean water, you may go up to design criteria of 15 gpm per sq. ft. Backwash flow
rate based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right)
are available upon request. AMI media filters are offered standard with electronic
programmable valves, but may be ordered with electromechanical Fleck valve
heads upon request.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-6
Filter-AG Filters for More Efficient Sediment Removal
About Filter-AG
Filter-Ag is a non-hydrous silicon dioxide media which can be used as highly
efficient filter media for the reduction of suspended matter.
Advantages of Filter-AG
 Less pressure loss than most other media filters
 Light weight requires lower back-wash rates & reduces shipping costs
 High service rates for lower equipment costs
 High sediment reduction capacity for longer filter runs, with a substantial savings in
backwash water & time out of service
Features and Specifications of AMI Filter-AG Filters
 High quality, high capacity filter media, Classified by Underwriters Laboratories Inc.® in
Accordance with Standard ANSI/NSF 61.
 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next backwash (21+” dia. units also
display current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile memory
 12-volt output AC Adapter provides safe and easy installation (20-volt output for 42” & 48”dia. units)
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum operating
temperature. (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Filter-Ag Limits: Maximum water temperature: 140°F/60°C
 Backwash: Time Clock Delayed (Metered, pressure-differential and PLC-controlled options are available upon request.)

Model No.* Flow Rate** (GPM) Backwash Volume of Media (ft3) Approx.
Resin Tank Valve In/Out
Flow** Filter-AG Total (Incl. Shipping Wt.
5gpm/ft2 15gpm/ft2 (Dia”×H”) Size Conn. (lbs)
(GPM) (Only) Underbed)
W-MA744ET 1 4 2.7 0.50 0.60 7×44 1” 1” 55
W-MA844ET 2 5 3.2 0.60 0.70 8×44 1” 1” 58
W-MA940ET 2 6 4.2 0.75 0.85 9×40 1” 1” 60
W-MA1054ET 2 7 5.3 1.25 1.45 10×54 1” 1” 85
W-MA1252ET 4 12 7.5 1.75 2.00 12×52 1” 1” 110
W-MA1354ET 4 14 9 2.00 2.30 13×54 1” 1” 140
W-MA1465ET 5 16 10 2.50 3.00 14×65 1” 1” 190
W-MA1665ET 7 21 15 3.50 4.00 16×65 1” 1” 235
W-MA2162ET 13 36 25 6.00 7.00 21×62 1.5” 1.5” 405
W-MA2472ET 15 47 30 8.00 10.0 24×72 2” 2” 635
W-MA3072ET 24 74 50 12.5 16.5 30×72 2” 2” 1,095
W-MA3672ET 35 106 70 17.0 22.0 36×72 2” 2” 1,395
W-MA4272ET 48 144 100 23.0 30.0 42×72 2” 2” 2,225
W-MA4872ET 60 180 125 30.0 43.6 48×72 2” 2” 3,425

Notes
* Filter-AG filters are available with USA or European style plugs and voltages. Please
add the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-MA744ET-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. For relatively
clean water, you may go up to design criteria of 15 gpm per sq. ft. Backwash flow
rate based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right) are
available upon request. AMI Filter-AG filters are offered standard with electronic
programmable valves, but may be ordered with electromechanical Fleck valve heads upon
request.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-7
Pyrolox Filters for Reducing Iron, Sulfur & Manganese
About Pyrolox
A mined Ore, Pyrolox is a mineral form of manganese dioxide which effectively reduces iron,
sulfur, and manganese from problem water. Pyrolox works on a principle whereby the
hydrogen sulfide, iron and manganese are oxidized and trapped on the media while simple
backwashing cleans the bed. No chemical regeneration is required, nothing is imparted into
the drinking water and Pyrolox has a high capacity for low contaminant concentrations.
Pyrolox can be used in conjunction with aeration, chlorination, ozone or other pretreatment
methods for difficult applications. Chlorine or other oxidants accelerate the catalytic reaction.
Advantages of Pyrolox
 Effective reduction of iron, sulfur and manganese
 Durable material with long service life and low annual attrition of bed
 No chemical regeneration required, only periodic backwashing
Features and Specifications of AMI Pyrolox Filters
 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next backwash (21+” dia. units
also display current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile memory
 12-volt output AC Adapter provides safe and easy installation
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum
operating temperature. (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Backwash: Time Clock Delayed (Metered, pressure-differential & PLC-controlled options are available upon request.)
 Pyrolox Operating Conditions: pH: 6.5 - 9.0; Because of its heavy weight, it is very important that Pyrolox
filters are backwashed properly to insure adequate bed expansion and continued service life.
Model No.* Service Backwash Volume of Media (ft3) Control Approx.
Resin Tank In/Out
Flow Rate** Flow** Pyrolox Total (Incl. Valve Shipping Wt.
(Dia”×H”)
Size Conn. (lbs)
(GPM) (GPM) (Only) Underbed)
W-MFI744PET 1.3 6.5 0.5 0.6 7×44 1” 1” 110
W-MFI844PET 1.7 7.5 0.6 0.7 8×44 1” 1” 120
W-MFI940PET 2.2 11 0.7 0.8 9×40 1” 1” 135
W-MFI1054PET 2.7 13 1.2 1.4 10×54 1” 1” 215
W-MFI1252PET 3.9 17 1.7 2.0 12×52 1” 1” 295
W-MFI1354PET 4.6 20 2.0 2.3 13×54 1” 1” 360
W-MFI1465PET 5.3 25 2.5 3.0 14×65 1” 1” 460
W-MFI1665PET 7.0 30 3.5 4.0 16×65 1.5” 1.5” 635
W-MFI2162PET 12.0 45 6.0 7.0 21×62 1.5” 1.5” 1,060
W-MFI2472PET 15.7 75 7.5 9.5 24×72 2” 2” 1,440

Notes
* Pyrolox filters are available with USA or European style plugs and voltages. Please
add the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-MFI744PET-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. Backwash flow
rate based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right)
are available upon request. AMI Pyrolox filters are offered standard with electronic
programmable valves, but may be ordered with electromechanical Fleck valve
heads upon request.
Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-8
Manganese Greensand Filters for Iron Reduction
About Manganese Greensand
Manganese Greensand is formulated from a glauconite greensand which is capable of reducing
iron, manganese and hydrogen sulfide from water through oxidation and filtration. When the
oxidizing capacity power of the Manganese Greensand bed is exhausted, the bed has to be
regenerated with a weak potassium permanganate (KMnO4) solution.
Advantages of Manganese Greensand
 Iron reduction over wide pH range
 Effective reduction of hydrogen sulfide in addition to iron and/or manganese
 No harmful effects from a chlorine feed
 Low attrition for long bed life
Features and Specifications of AMI Manganese Greensand Filters
 Manganese Greensand filtration media is Certified to ANSI/NSF Standard 61
 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next backwash (21+” dia. units also display
current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile memory
 12-volt output AC Adapter provides safe and easy installation (20-volt output for 42” & 48”dia. units)
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum operating
temperature. (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Regeneration/Backwash*: Time Clock Delayed (Metered, pressure-differential & PLC-controlled options are available upon request.)
 Manganese Greensand Limits: Maximum water temperature: 80°F/26.7°C; pH Range: 6.2-8.5

Model No.** Service Flow Backwash Volume of Media (ft3) Resin Regen. Control Approx.
In/Out
Rate*** Flow** Greensand Total (Incl. Tank Tank Valve Shipping
(Only) Size Conn. Wt. (lbs)
(GPM) (GPM) Underbed) (Dia”×H”) (Dia”×H”)
W-MFI744GET 1.3 2.7 0.50 0.60 7×44 18×33 1” 1” 85
W-MFI844GET 1.7 3.2 0.60 0.70 8×44 18×33 1” 1” 95
W-MFI940GET 2.2 4.2 0.75 0.85 9×40 18×40 1” 1” 110
W-MFI1054GET 2.7 5.3 1.25 1.45 10×54 18×40 1” 1” 165
W-MFI1252GET 3.9 7.5 1.75 2.00 12×52 18×40 1” 1” 225
W-MFI1354GET 4.6 9 2.00 2.30 13×54 18×40 1” 1” 270
W-MFI1465GET 5.3 10 2.50 3.00 14×65 27×41 1” 1” 350
W-MFI1665GET 7.0 15 3.50 4.00 16×65 -- 1” 1” 460
W-MFI2162GET 12.0 25 6.00 7.00 21×62 -- 1.5” 1.5” 795
W-MFI2472GET 15.7 30 8.00 10.0 24×72 -- 2” 2” 1,145
W-MFI3072GET 24.5 50 12.5 16.5 30×72 -- 2” 2” 1,900
W-MFI3672GET 35.3 70 17.0 22.0 36×72 -- 2” 2” 2,490
W-MFI4272GET 48.1 100 23.0 30.0 42×72 -- 2” 2” 3,690
W-MFI4872GET 63.0 125 30.0 43.6 48×72 -- 2” 2” 5,340
Notes
* Manganese greensand filters with tank diameters up to 14” can be regenerated
intermittently, and the regeneration feed is included. Filters with tank diameters of 16”
and larger require continuous injection of potassium permanganate which will require a
tank and feeder. The size of the injection system (sold separately) will depend on the
water quality.
** Manganese Greensand filters are available with USA or European style plugs and
voltages. Please add the appropriate voltage code to the end of the model when
ordering. 120V AC/60Hz with USA cord = US Example: W-MFI744ETG-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
*** 5 gpm per sq. ft. of media is the best design condition for filtration. Backwash flow rate based on 25 psi pressure drop
Skid mounting, control panel and custom sizes and configurations (shown on right) are available upon request. AMI greensand filters are offered standard with
electronic programmable valves, but may be ordered with electromechanical Fleck valve heads upon request.
Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-9
Calcite Filters for Neutralizing pH of Water
About Calcite
Calcite is a naturally occurring calcium carbonate media. One of the advantages of Calcite
is its self-limiting property. When properly applied, it corrects pH only enough to reach a non-
corrosive equilibrium. It does not overcorrect under normal conditions. Upon contact with
calcite, acidic waters slowly dissolve the calcium carbonate to raise the pH which reduces
potential leaching of copper, lead and other metals found in typical plumbing systems.
Periodic backwashing will prevent packing, reclassify the bed and maintain high service rates.
Depending on pH, water chemistry and service flow, the Calcite bed will have to be
periodically replenished as the Calcite is depleted. As the Calcite’s calcium carbonate
neutralizes the water, it will increase hardness and a softener may become necessary after the
neutralizing filter.
Advantages of Calcite
 Naturally occurring, inexpensive material
 Low uniformity coefficient for maximum contact
 Slower Reacting for controlled pH correction

Features and Specifications of AMI Calcite Filters

 Fully automated with state of the art electronic control valve featuring:
 Solid state microprocessor with easy access front panel settings
 Front panel display with time of day & gallons until next backwash (21+” dia. units also
display current flow rate, and total volume used)
 Days override feature; 1-28 days available
 Coin Cell Lithium battery back-up with 8 hour carry over
 Stores system configuration and operation data in nonvolatile memory
 12-volt output AC Adapter provides safe and easy installation
 High quality FRP/Composite Resin Tank, rated at 150 psi maximum operating pressure and 120°F maximum operating
temperature. (Optional stainless steel jackets are available for 9”-16” diameter tanks upon request.)
 Backwash: Time Clock Delayed (Metered, pressure-differential & PLC-controlled options are available upon request.)

Model No.* Volume of Media (ft3) Control Approx.

Service Flow Backwash Resin Tank In/Out
Calcite Total (Incl. Valve Shipping Wt.
Rate** (GPM) Flow** (GPM) (Dia”×H”) Conn. (lbs)
(Only) Underbed) Size
W-N744ET 1.3 2.7 0.5 0.6 7×44 1” 1” 90
W-N844ET 1.7 3.2 0.6 0.7 8×44 1” 1” 100
W-N940ET 2.2 4.2 0.7 0.8 9×40 1” 1” 110
W-N1054ET 2.7 5.3 1.2 1.4 10×54 1” 1” 175
W-N1252ET 3.9 7.5 1.7 2.0 12×52 1” 1” 225
W-N1354ET 4.6 9 2.0 2.4 13×54 1” 1” 285
W-N1465ET 5.3 10 2.6 3.1 14×65 1” 1” 375
W-N1665ET 7 15 3.6 4.1 16×65 1” 1” 490
W-N2162ET 12 25 5.9 6.9 21×62 1.5” 1.5” 820
W-N2472ET 15.7 30 8.0 10.0 24×72 2” 2” 1,200
W-N3072ET 24.5 50 12.4 16.4 30×72 2” 2” 1,965
W-N3672ET 35.3 70 17.1 22.1 36×72 2” 2” 2,595
W-N4272ET 48.1 100 23.1 30.1 42×72 2” 2” 3,855
W-N4872ET 63.0 125 30.3 43.8 48×72 2” 2” 5,565
Notes
* Calcite filters are available with USA or European style plugs and voltages. Please
add the appropriate voltage code to the end of the model when ordering.
120V AC/60Hz with USA cord = US Example: W-N744ET-US
European 220V AC = EU (EU plug is removable to convert into universal 220v cord)
** 5 gpm per sq. ft. of media is the best design condition for filtration. Backwash
flow rate based on 25 psi pressure drop.
Skid mounting, control panel and custom sizes and configurations (shown on right) are
available upon request. Offered standard with electronic programmable valves, but may be
ordered with electromechanical Fleck valves upon request.

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-10
Filtration Media and Resin
Carbon, Sediment, Iron Reduction, & Support Media
Carbon Media
Mesh Volume/Wt per Bag
Model No. Type Grade Applications
Size cu.ft. lbs.
YMC0830RCOAL Coal Base 8×30 Regular Industrial/Non-Critical 1 27.5
YMC1240RCOAL Coal Base 12×40 Regular Industrial/Non-Critical 1 27.5
YMC1240HCOAL Coal Base 12×40 High Density Large Industrial 1 33.0
YMC0830HAWCOAL Coal Base 8×30 HD Acid Washed Potable Water 1 33.0
YMC1240HAWCOAL Coal Base 12×40 HD Acid Washed Potable Water 1 33.0
YMC0830RCOCO Coconut Shell 8×30 Regular Beverage, Dialysis 1 27.5
YMC1240RCOCO Coconut Shell 12×40 Regular Beverage, Dialysis 1 27.5
YMC1240RCOCO65* Coconut Shell 12×40 Regular, Prop 65 Tested Beverage, Dialysis 1 27.5
YMC1240AWCOCO Coconut Shell 12×40 Acid Washed Beverage, Dialysis 1 27.5
*YMC1240RCOCO65 Prop 65 Tested Carbon may be subject to minimum orders depending on stock and availability.
All Carbons are also available in 1100 lb. super sacks.
Sediment Filtration Media
Model No. Description Application Volume (Cu. Ft.) Weight (Lbs.)
YMFAG Filter Ag Sediment Removal 1 25
YMS20S Silica Sand, #20 Sediment Removal 1 100
YMS4555 Filter Sand, 0.45-0.55 mm, 40-30 Mesh Sediment Removal 1 100
YMG3040 Garnet, #30-40, 0.35 mm Sediment Removal 0.38 50
YMA89 Anthracite, 0.8-0.9 mm, 10x20 Mesh Sediment Removal 1 50
YMA1720 Anthracite, 1.7-2.0 mm, 4x12 mesh Sediment Removal 1 50

Iron, Manganese, and H2S Reduction Media

Model No. Description Application Volume (Cu. Ft.) Weight (Lbs.)
YMMNGS Manganese Greensand Iron Removal 1.00 85
YMP2040 Pyrolox 8x20 Mesh, 0.51 mm Iron Removal 0.40 50
YMKDF55 KDF-55 Chlorine Reduction 0.33 57
YMKDF85 KDF-85 Fe, H2S Reduction 0.33 57
YFMBIRM Birm Iron Removal 1.00 44
YMMTM MTM Iron Removal 1.00 45

Acid Neutralization Media

Model No. Description Application Volume (Cu. Ft.) Weight (Lbs.)
YMCAL Calcite Raise pH of Water 0.55 50

Support Media
Volume Weight
Model No. Description
(Cu. Ft.) (Lbs.)
YMGRVL11618-50 Gravel, 1/16” x ⅛”, #6 0.5 50
YMGRVL1418-50 Gravel, ¼” x ⅛” 0.5 50
YMG812 Garnet, #8-12, 1.5 mm 0.36 50

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-11
Filtration Media and Resin
Ion Exchange Resins
DOWEX™ Ion Exchange Resin
Qty. Per Container Exchange
Model No. Description Volume Approx. Capacity
(cu.ft.) Wt. (lbs) eq/I (kgr/ft3)
Strong Acid Cation Exchange Resin for Residential Softening
HCRSSBAG 1 25 1.9 (41.5)
Applications, 6% Crosslinked, DOWEX HCR-S/S, Na+ Form
Strong Acid Cation Exchange Resin for Softening and
HCR Demineralization Applications, 8% Crosslinked, 5 255 2.0 (43.7)
DOWEX HCR-S, Na+ Form
Strong Acid Cation Exchange Resin For Softening and
MARATHONCH 5 250 1.8 (39.3)
Demineralizing Applications, DOWEX MARATHON C, H+ Form
Strong Base Anion Exchange Resin For Demineralization
MARATHONAOH 5 200 1.0 (21.9)
Applications, DOWEX MARATHAN A, OH- Form
Mixed Ion Exchange Resin for Demineralization, 1:1 by OH-: 1.0 (21.9)
MARATHONMR3 5 210
Equivalent, DOWEX MARATHON MR-3, OH- & H+ Form H+: 1.9 (41.5)

ResinTech Ion Exchange Resins

Model No. Description Qty. Per Container Exchange
Volume Approx. Capacity,
(cu.ft.) Wt. (lbs) (meq/L)
Softening Resins (Strong Acid Cation)
High Capacity Gel Type Cation Resin For Softening/Deionization
CGS 1 51 1.9
Applications, Na Form
Industrial Grade High Capacity Cation Resin for
CG8 1 52 1.9
Softening/Deionization Applications, 8% Crosslink, Na Form
Industrial Grade High Capacity Cation Resin for Softening/
CG8-H 1 50 1.8
Deionization Applications, 8% Crosslink, H Form
Weak Acid Cation Resins
WACG Weak Acid Gel - Dealkalization/Chemical Processing (H Form) 1 47 > 4.00
Strong Base Anion Resins
SBG1P Type One Porous Gel - Deionization/Mixed Beds (Cl Form) 1 43 > 1.25
SBG1P-OH Strong Base Acrylic Type One - Deionization Systems (OH Form) 1 41 > 1.00
SBG1 Strong Base Type One Gel - Anion Removal/Deionization (Cl Form) 1 44 > 1.45
SBG1-OH Strong Base Type One Gel - Deionization/Mixed Beds (OH Form) 1 41 1.15
SBG2 Strong Base Type Two Gel – Anion Removal/Deionization (Cl Form) 1 44 > 1.45
SBG2-HP SBG2 – Drinking Water Grade (Cl Form) 1 44 > 1.45
SBG2-OH Strong Base Type Two Gel - Dealkalization/Deionization (OH Form) 1 42 > 1.3
Mixed Bed Resins (Regenerated)
Cation: 1.95
MBD-10 Mixed Bed resin, RSO3-H+ (Gel) and R4N+OH- (Type One Gel) 1 43 Anion: 1.40
Cation: 1.95
MBD-15-NG Mixed Bed Resin - General Purpose (Nuclear Grade) 1 43 Anion: 1.25
Cation: 1.95
MBD-15-SC Mixed Bed Resin - Semiconductor Grade 1 43 Anion: 1.25
Specialty Resins
SIR-200 Chelating Resin - Mercury Removal (H Form) 1 41 1.10
SIR-22P-HP High Porosity Gel Type 1 - Organic Trap (Cl Form) 1 41 n/a
SIR-100-HP Anion Exchange Resin - Nitrate Selective (Cl Form) 1 42 0.85
SIR-110-HP Anion Exchange Resin - Nitrate & Perchlorate (Cl Form) 1 43 0.60
SIR-300 Chelating Resin - Heavy Metals Removal (Na Form) 1 43 > 1.10
SIR-900 Absorbent - Arsenic, Fluoride & Lead 1 47 1.40

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-12
Media Filtration Components
Fleck Residential Control Valves
Fleck controls are available with the following options upon customer request:
 7 or 12 Day Timers, Electronic timer, Metered, Pressure Differential, and Other Regeneration Methods
 Hot Water  Manual Operation  Service Valve Operator
 No Hard Water Bypass  Bypass Valve  Up-Flow Regeneration
5600 Series Valves
Typical Applications: Water Softeners 6” – 12” Diameter, Filters 8” – 10” Diameter.
Flow Rates: (50 PSI Inlet)  Valve Material: Noryl  Hard Water Bypass
 Continuous (15 psi drop): 20 gpm  ¾” In/Out Connections  NSF Standard 44 Certified
 Peak (25 psi drop): 26 gpm  2½” – 8 NPSM Mounting Base  UL Registered Components
 Max Backwash (25 psi drop): 7 gpm  1600 Brine System (softener)
Filter or Meter Capacity
AMI Model No. Metered/Timered
Softener Range
YVS56BXAAS03 Softener 7 Day timer n/a
YVS56CAAAS03 Softener Meter Delay, Std. ¾” 125-2,125 Gal.
YVF56BXAAS03 Filter 7 Day Timer n/a
YVS56UAADS03 Softener SXT Electronic Meter ¾” 1-9,999 Gal
YVS56UXADS03 Softener SXT Electronic Timer --
YVF56UXADS03 Filter SXT Electronic Timer --
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 3 gpm backwash flow (indicated by last 2 digits). Other backwash flows are available (max. 7 gpm).

2510 Series Valves

Flow Rates: (50 PSI Inlet)  Valve Material: Fiber-Reinforced Polymer  Hard Water Bypass
 Continuous (15 psi drop): 19 gpm  1” In/Out Connections  Typical Applications:
 Peak (25 psi drop): 24 gpm  2½” – 8 NPSM Mounting Base  Softeners 6” – 16” Dia.
 Max Backwash (25 psi drop): 17 gpm  1600 Brine System (softener)  Filters 8” – 16” Dia.
Filter or Meter Capacity
AMI Model No. Metered/Timered
Softener Range
YVS25AXBAS07 Softener 12 Day Timer n/a
YVS25CABAS07 Softener Meter Delay, Std. ¾” 125-2,125 Gal.
YVS25DABAS07 Softener Meter Delay, Ext Range ¾” 625-1,0625 Gal
YVF25AXBAS07 Filter 12 Day timer n/a
YVS25MABDS07 Softener SXT Electronic Meter ¾” 1-9,999 Gal.
YVS25LXBDS07 Softener SXT Electronic Timer n/a
YVF25LXBDS07 Filter SXT Electronic Timer n/a
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 7 gpm backwash flow (indicated by last 2 digits). Other backwash flows are available (max. 15 gpm).

2750 Series Valves

Flow Rates: (50 PSI Inlet)  Valve Material: Lead-Free Brass  Hard Water Bypass
 Continuous (15 psi drop): 26 gpm  1” In/Out Connections  Typical Applications:
 Peak (25 psi drop): 33 gpm  2½” – 8 NPSM Mounting Base  Softeners 10” – 24” Dia.
 Max Backwash (25 psi drop): 25 gpm  1600 Brine System (softener)  Filters 10” – 21” Dia.
Filter or Meter Capacity
AMI Model No. Metered/Timered
Softener Range
YVS27AXXAS07 Softener 12 Day Timer n/a
YVS27CAXAS07 Softener Meter Delay, Std. ¾” 310-5,270 Gal.
YVS27DBXAS07 Softener Meter Delay, Ext Range 1” 1,550-26,350 Gal
YVF27AXXAS07 Filter 12 Day timer n/a
YVS25MABDS07 Softener SXT Electronic Meter ¾” 1-9,999 Gal.
YVS25LXBDS07 Softener SXT Electronic Timer n/a
YVF25LXBDS07 Filter SXT Electronic Timer n/a
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 7 gpm backwash flow (indicated by last 2 digits). Other backwash flows are available (max. 25 gpm).
Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-13
Media Filtration Components
Fleck Commercial Control Valves
2850 Series Valves
Flow Rates: (50 PSI Inlet)  Valve material: Lead-Free Brass  1700 Brine System (softener)
 Continuous (15 psi drop): 51 gpm  1½” In/Out Connections  Hard Water Bypass
 Peak (25 psi drop): 66 gpm  4” – 8 UN Mounting Base
 Max Backwash (25 psi drop): 49 gpm
Filter or Meter Capacity
AMI Model No. Metered/Timered
Softener Range
YVS28AXXAS25 Softener 12 Day Timer n/a
YVS28CBXAS25 Softener Meter Delay, Std. 1” 310-5,270 Gal.
YVS28DCXAS25 Softener Meter Delay, Ext Range 1.5” 3,125-53,125 Gal
YVF28AXXAS25 Filter 12 Day timer n/a
YVS28MBXDS25 Softener SXT Electronic Meter 1” 1-9,999 Gal.
YVS28LXXDS25 Softener SXT Electronic Timer n/a
YVF28LXXDS25 Filter SXT Electronic Timer n/a
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 25 gpm backwash flow (indicated by last 2 digits). Other backwash flows are available (max. 45 gpm).

3150 Series Valves

Flow Rates: (50 PSI Inlet) – For Top Mount  Valve material: Lead-Free Brass  1800 Brine System (softener)
 Continuous (15 psi drop): 95 gpm  2” NPTF In/Out Connections  Hard Water Bypass
 Peak (25 psi drop): 124 gpm  4” – 8 UN Mounting Base
 Max Backwash (25 psi drop): 105 gpm
Filter or Meter Capacity
AMI Model No. Metered/Timered
Softener Range
YVS31AXXAS55 Softener 12 Day Timer --
YVS31CBXAS55 Softener Meter Delay, Std. 1” 1,250-21,250 Gal.
YVS31DCXAS55 Softener Meter Delay, Ext Range 1.5” 6,250-106,250 Gal.
YVF31AXXAS55 Filter 12 Day Timer --
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 55 gpm backwash flow (indicated by last 2 digits). Other backwash flows are
available (max. 100 gpm).

3900 Series Valves

Flow Rates: (50 PSI Inlet) – For Top Mount  Valve Material: Lead-Free Brass  1800 Brine System (softener)
 Continuous (15 psi drop): 250 gpm  3” NPT In/Out Connections  Hard Water Bypass
 Peak (25 psi drop): 325 gpm  6” – 8 Threaded or Flanged
 Max Backwash (25 psi drop): 100 gpm
Filter or Meter Capacity
AMI Model No. Metered/Timered
Softener Range
YVS39AXXAS99 Softener 12 Day Timer --
YVS39CEXAS99 Softener Meter Delay, Std. 3” 3,750-63,750 Gal.
YVS39DEXAS99 Softener Meter Delay, Ext Range 3” 18,750-318,750 Gal.
YVS39GXXAD99 Softener Twin Alternating- Lead Needs Remote Meter
YVS39GXXAG99 Softener Twin Alternating- Lag Needs Remote Meter
YVF39AXXAS99 Filter 12 Day Timer --
YVF39CEXAS99 Filter Meter Delay, Std. 3” 3,750-63,750 Gal.
YVF39DEXAS99 Filter Meter Delay, Ext Range 3” 18,750-318,750 Gal.
 Valves shown 110v/60Hz; other voltages available.
 Valves shown with 100 gpm backwash flow.
Other backwash flows are available (max. 100 gpm).

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-14
Media Filtration Components
Fleck Twin Alternating & Hot Water Control Valves
9000 Series Brass Twin Alternating Softener Valves
Flow Rates: (50 PSI Inlet) 1” meter ¾” meter  Valve Material: Lead-Free Brass  1600 Brine System ⅜”
 Continuous (15 psi drop): 21 gpm 18 gpm  2½” – 8 NPSM Mounting Base  No Hard Water Bypass
 Peak (25 psi drop): 28 gpm 24 gpm  1” In/Out Connections (¾” or 1 ¼”
 Max Backwash (25 psi drop): 8.5 gpm 8.5 gpm connections are also available)
AMI Model No. Metered/Timered Meter Capacity Range
YVS90EABAT03 Meter Immediate, Std. Range ¾” 125-1,125 Gal.
YVS90FBBAT03 Meter Immediate, Ext. Range 1” 1,550-26,350 Gal.
YVS90MABDT03 SXT Electronic Meter, ¾” 1-9,999 Gal.
YVS90MBBDT03 SXT Electronic Meter, 1” 1-9,999 Gal.
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 3 gpm backwash flow (indicated by last 2 digits). Other backwash flows are available (max. 7 gpm).

9100 Series Noryl Twin Alternating Softener Valves

Flow Rates: (50 PSI Inlet) 1” meter ¾” meter  Valve Material: Fiber-Reinforced Polymer  1600 Brine System ⅜”
 Continuous (15 psi drop): 21 gpm 18 gpm  2½” – 8 NPSM Mounting Base  No Hard Water Bypass
 Peak (25 psi drop): 28 gpm 24 gpm  1” In/Out Connections (¾” or 1 ¼”
 Max Backwash (25 psi drop): 8.5 gpm 8.5 gpm connections are also available)
AMI Model No. Metered/Timered Meter Capacity Range
YVS91EABAT03 Meter Immediate, Std. Range ¾” 125-1,125 Gal.
YVS91FBBAT03 Meter Immediate, Ext. Range 1” 1,550-26,350 Gal.
YVS91MABDT03 SXT Electronic Meter, ¾” 1-9,999 Gal.
YVS91MBBDT03 SXT Electronic Meter, 1” 1-9,999 Gal.
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 3 gpm backwash flow. Other backwash flows are available (max. 7 gpm).

9500 Series Brass Twin Alternating Softener Valves

Flow Rates: (50 PSI Inlet)  Valve Material: Lead-Free Brass  1700 Brine System ½”
 Continuous (15 psi drop): 38 gpm  2½” – 8 NPSM Mounting Base  No Hard Water Bypass
 Peak (25 psi drop): 49 gpm  1½” NPTF  Typical Application: 10”-24” Dia. Softener
 Max Backwash (25 psi drop): 16 gpm
AMI Model No. Metered/Timered Meter Capacity Range
YVS95ECXAT15 Meter Immediate, Std. Range 1.5” 625-10,625 Gal.
YVS95FCXAT15 Meter immediate, Ext. Range 1.5” 3,125-53,125 Gal.
 Valves shown 110v/60Hz (SE Valves are 24v/60Hz with 110v transformer); other voltages available.
 Valves shown with 15 gpm backwash flow. Other backwash flows are available (max. 16 gpm).

4650 Series Hot Water Residential Control Valve

 Operating Temp: 34°-110°F (1°-43°C)  Valve Material: Lead-Free Brass  No Hard Water Bypass
Flow Rates (50 PSI Inlet):  2½” – 8 NPSM Mounting Base  Typical Applications:
 Continuous (15 psi drop): 20 gpm  1” NPT In/Out ( ¾” & 1¼” also available)  Softeners 6” – 12” Dia.
 Peak (25 psi drop): 26 gpm  1600 Brine System ⅜” (Softener)  Filters 6” – 10” Dia.
 Max Backwash (25 psi drop): 7 gpm
AMI Model No. Filter or Softener Timer Meter
YVS46BXBAS05 Softener 12 Day Timer No Meter Option
YVF46BXBAS05 Filter 12 Day Timer No Meter Option
 Valves shown 110v/60Hz; other voltages available.
 Valves shown with 5 gpm backwash flow. Other backwash flows are available (max. 7 gpm).

Series 1000 Remote Reset Meters for Multi-Tank Systems Using Multiple Valves
Model No. Meter Meter Cap. Range Model No. Meter Meter Cap. Range
YV1000-10S-* 1” Standard Range 0-5,000 YV1000-20S-* 2” Standard Range 0-21,000
YV1000-10E-* 1” Extended Range 0-25,000 YV1000-20E-* 2” Extended Range 0-100,000
YV1000-15S-* 1 ½” Standard Range 0-10,000 YV1000-30S-* 3” Standard Range 0-65,750
YV1000-15E-* 1 ½” Extended Range 0-50,000 YV1000-30E-* 3” Extended Range 0-320,000
*Please add voltage code to part number when ordering. 24 = 24v 50/60Hz; 110 = 110v, 60Hz; 220 = 220v 50/60Hz Example: YV100-10S-110

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-15
Media Filtration Components
Poly Glass & Composite Mineral Tanks

 Pressure tanks are made of high performance composite

material with FRP filament winding, with complete seamless
molding technology
 All thread inlet made from 30% glass filled PP provides higher
strength, temperature and pressure limits versus glass filled PE
 All pressure tanks are 100% corrosion resistant
 Color: Natural color is standard, specify other color if required
 Tank base included
 Mounting: Top Mount
 Maximum operating pressure: 150 psi (1 MPa)
 Maximum operating temperature:
 Threaded Tanks: 120°F (50°C)
 Flanged Tanks: 150°F (65°C)

 NSF and PED (CE) Certified

Size Capacity Size Capacity Bottom

Model No. Top Opening Model No. Top Opening
(Dia”×H”) (cu.ft.) (Dia”×H”) (cu.ft.) Opening
YTP0618-25 6×18 0.24 2.5” Threaded YTP1447-4 14×47 3.68 4” Threaded n/a
YTP0735-25 7×35 0.70 2.5” Threaded YTP1447-45 14×47 3.68 4.5” Threaded n/a
YTP0744-25 7×44 0.90 2.5” Threaded YTP1465-25 14×65 5.43 2.5” Threaded n/a
YTP0818-25 8×18 0.52 2.5” Threaded YTP1465-4 14×65 5.43 4” Threaded n/a
YTP0835-25 8×35 0.88 2.5” Threaded YTP1665-4 16×65 6.55 4” Threaded n/a
YTP0844-25 8×44 1.16 2.5” Threaded YTP1865-4 18×65 8.30 4” Threaded n/a
YTP0940-25 9×40 1.27 2.5” Threaded YTP2162-4 21×62 11.0 4” Threaded n/a
YTP0948-25 9×48 1.58 2.5” Threaded YTP2472-4 24×72 15.9 4” Threaded n/a
YTP1035-25 10×35 1.36 2.5” Threaded YTP2472-6F 24×72 15.9 6” Flanged n/a
YTP1040-25 10×40 1.54 2.5” Threaded YTP3072-4 30×72 25.0 4” Threaded n/a
YTP1054-25 10×54 2.19 2.5” Threaded YTP3072-6F 30×72 25.0 6” Flanged n/a
YTP1242-25 12×42 2.55 2.5” Threaded YTP3672-4 36×72 35.3 4” Threaded n/a
YTP1242-45 12×42 2.55 4.5” Threaded YTP3672-6F 36×72 35.3 6” Flanged n/a
YTP1252-25 12×52 2.97 2.5” Threaded YTP3672-6F6F 36×72 35.3 6” Flanged 6” Flanged
YTP1252-4 12×52 2.97 4.0” Threaded YTP4272-6F 42×72 46.1 6” Flanged n/a
YTP1354-25 13×54 3.68 2.5” Threaded YTP4272-6F6F 42×72 46.1 6” Flanged 6” Flanged
YTP1354-4 13×54 3.68 4.0” Threaded YTP4872-6F 48×72 61.9 6” Flanged n/a
YTP1447-25 14×47 3.68 2.5” Threaded YTP4872-6F6F 48×72 61.9 6” Flanged 6” Flanged

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-16
Media Filtration Components
Distributors, Diffusers, Hub and Lateral Assemblies
Top Mount, Riser Tube, Composite
For Tank Top Opening System Flow Rate
Model No. Laterals
(Dia”) (in) Connection (gpm)
YD5665 18-16 4-8 1.5”Slip 29 6
YD5666 18-21 4-8 1.5”Slip 29 6
YD5667 24 4-8 1.5”Slip 29 6
YD10848 30 4 or 6-8 1.5”Slip 104 6
YD10849 36 4 or 6-8 1.5”Slip 104 6
YD12201 24 6 Flanged 3”Slip 104 8
YD5672 30 6 Flanged 3”Slip 104 8
YD5673 36 6 Flanged 3”Slip 104 8
YD5674 42 6 Flanged 3”Slip 104 8
YD5675 48 6 Flanged 3”Slip 104 8
YD13492 63 6 Flanged 3”Slip 104 8
YD11776 30 6 Flanged 3”Slip 173 16
YD11778 36 6 Flanged 3”Slip 173 16
YD5676 42 6 Flanged 3”Slip 173 16
YD5677 48 6 Flanged 3”Slip 173 16
YD13569 63 6 Flanged 3”Slip 174 16

Diffusers
For Tank System Flow Rate
Model No. Mouting Top Opening
(Dia”) Connection (gpm)
YD5671 12-36 Top/Bottom 4”-8” Threaded 2” Slip 88
YD5679 18-48 Top 6” Flanged 3” FNPT 88
YD5700 21-36 Top 6”-8” Threaded 3” FNPT 88

Hub and Lateral

Model For Tank Top/Bottom System Flow Rate
Mounting Material
No. (Dia”) Opening Conn. (gpm)
YD5680 21-63 Top 6” Flanged Composite 3” Slip 200
YD10877 42-63 Top 16” Manway Composite 3” Slip 200
YD5669 18-21 Bottom 4”-8” Threaded Composite 2” Slip 100
YD5670 24 Bottom 4”-8” Threaded Composite 2” Slip 100
YD11039 30 Bottom 4”-8” Threaded Composite 2” Slip 100
YD11040 36 Bottom 4”-8” Threaded Composite 2” Slip 100
YD11790 18 Bottom 6” Flanged Composite 3” Slip 122
YD5696 21 Bottom 6”-8” Threaded FRP 3” Slip 122
YD5678 21-24 Bottom 6” Flanged Composite 3” Slip 122
YD5697 24 Bottom 6”-8” Threaded FRP 3” Slip 122
YD5698 30 Bottom 6”-8” Threaded FRP 3” Slip 122
YD5683 30 Bottom 6” Flanged Composite 3” Slip 122
YD5699 36 Bottom 6”-8” Threaded FRP 3” Slip 122
YD5684 36 Bottom 6” Flanged Composite 3” Slip 122

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-17
Media Filtration Components
Mineral Tank Adapters and Accessories

Threaded Tank Adapters - 150 psi max pressure SNA Flanged Adapters
 Structural Bolt Pattern
Max Temp.  150 PSI/150°F
Model No. Reduced To Material Image
°F °C  Kits come complete with standard o-ring and hardware
2.5-8” NPSM  Replacement Hardware: CPVC-YTA5310; Noryl-YTA4750
YTA27513 0.75 ”NPT PVC 120 48
YTA27515 1 ”NPT PVC 120 48
YTA27518 1.25 ”NPT PVC 120 48 Flange
YTA27514 1.5 ”NPT PVC 120 48 Model No. Material Adapt To Drain
Size
YTA27516 2.25-16” PVC 120 48
4-8” UN YTA10659 6” CPVC 1” NPT NO
YTA48216 1 ”NPT CPVC 150 65 YTA10660 6” CPVC 1.5” NPT NO
YTA482112 1.25 ”NPT CPVC 150 65 YTA10661 6” CPVC 2” NPT NO
YTA48217 1.5 ”NPT CPVC 150 65 YTA10662 6” CPVC 3” NPT NO
YTA48218 2 ”NPT CPVC 150 65 YTA10663 6” CPVC 4” NPT NO
YTA482117 2-11.5 ”NPSM CPVC 150 65 3” NPT to
YTA5292 6” NORYL YES
YTA48212 2.5-8” NPSM CPVC 150 65 3” NPT
YTA48214 3-8” UN CPVC 150 65 3” NPT to
YTA5267 6” NORYL NO
YTA482111 2.375” BORED CPVC 150 65 3” NPT
6-8” UN 3” NPT to
YTA5295 6” NORYL NO
4”-8 UN
YTA4125003 3” FPT NORYL 150 65
YFL10566 6” NORYL 4”-8 UN NO
Threaded Closures
YTA27511 2.5-8” NPSM PVC 120 48
YTA48211 4-8” UN CPVC 150 65
YTA26951 6-8” UN CPVC 150 65
ANSI Flanged Adapters
 Standard Bolt Pattern
 Replacement Hardware: 4”- YTA525; 10”- YTA5754
Brass Side Adapters - 150 psi max pressure
Max Temp. Flange
Model No. Reduced To Model No. Material Adapt To Drain
°F °C Size
0.75” NPT to
YTA1661 150 65
0.75” FNPT YTA5276 4” CPVC 3” NPSM NO
1.5” NPT to YTA10673 4” CPVC 2” NPT NO
YTA2829 150 65
1.5” FNPT YTA10674 4” CPVC 3” NPT NO
YTA11929 10” CPVC 4” NPT NO
YTA11930 10” CPVC 6” NPT NO
Vacuum Breakers
Max Temp. Max
Model No. Connection
°F °C Pressure Replacement O-Rings
YTA10725 1” FNPT 150 65 150
YTA10724 1.5” MNPT 120 48 125 Model No. For Tank with Opening
YTA2694-120 2” Elbow
YTA2694-112 2.5” Thread
Wrenches YTA2694-114 4” Thread
YTA2694-136 4” ANSI Flange
Model No. Size
YTA2694-68 6” Thread
YTA65682 4” YTA2694-69 6” SNA Flange
YTA7229 YTA2694-132 10” ANSI Flange
6”
YTA2694-131 16” MWY Flange

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-18
Media Filtration Components
Accessories and SS Jackets for Tanks
Flanged Closures Manway Closures/Adapters
 For 16” Manway Openings
 SNA = Structural Type Bolt Patten, ANSI = Standard Bolt Pattern
 Max. Temp 150°F
 Kits come complete with standard o-ring and hardware
 Kits come complete with standard o-ring and hardware
Flange Flange  Replacement Hardware: YTA10107
Model No. Material Model No. Reduced To Material
Size Type
YTA10108 2” NPT Vinylester
YTA5296 6” SNA NORYL
YTA14644 2” NPT to 3”NPT Vinylester
YTA10658 6” SNA CPVC YTA10582 2” NPT CPVC
YTA10583 3” NPT CPVC
YTA5259 4” ANSI CPVC
YTA10584 4” NPT CPVC
YTA10472 4” ANSI ACRYLIC YTA11294 3” NPT to 3” NPT CPVC
YTA11295 4” NPT to 4” NPT CPVC
YTA10139 10” ANSI CPVC YTA5294 2” NPT Stainless

Connections and Accessories

 Kits come complete with o-ring and hardware if it is required.

Flexible Assembly (NPT – NPT) Flexible Assembly (Flanged)

Model No. Description Model No. Description

YTA5285 2” NPT X 2” NPT

4” Flanged to 3” NPT (CPVC)
YTA5239
150psi/150°F
YTA5286 3” NPT X 3” NPT

Connector Elbow
Model No. Description Model No. Description

2” NPSM to 2” Slip (CPVC)

YTA5045 3” NPSM x 3” NPT (CPVC) YTA5201
150psi/150°F

Stainless Steel Jackets for Mineral Tanks Caps for Stainless Steel Jackets
Model No. For Tank Size (Dia.” × Height”) Sold separately – not included with jackets.

YTP0940JKT 9×40 Model No. For Tank Diameter

YTP0948JKT 9×48 YTP09JCAP 9”

YTP1035JKT 10×35 YTP10JCAP 10”
YTP1040JKT 10×40 YTP12JCAP 12”
YTP1054JKT 10×54 YTP13JCAP 13”
YTP1242JKT 12×42 YTP14JCAP 14”
YTP1252JKT 12×52 YTP16JCAP 16”
YTP1354JKT 13×54
YTP1447JKT 14×47
YTP1465JKT 14×65
YTP1665JKT 16×65

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-19
Media Filtration Components
Media Regeneration - Brine Tanks, Cabinets, Feeders
Brine Tank Assemblies
 Assembled with well, lid, brine valve, and grid plate.
 Standard color is black. Available in other colors upon request.

Model No. Size (Dia.” × Height”)

YBT1833ASSEMBL 18”×33”
YBT1840ASSEMBL 18”×40”
YBT2441ASSEMBL 24”×41”
YBT2450ASSEMBL 24”×50”
YBT3048ASSEMBL 30”×48”
YBT3948ASSEMBL 39”×48”
YBT3960ASSEMBL 39”×60”
YBT4260ASSEMBL 42”×60”
YBT5060ASSEMBL 50”×60”
YBT6060ASSEMBL 60”×60”

Cabinet Assemblies
 Windsor Hi-Profile Series accommodates most control valves.
 Assembly includes blow molded cabinet, one piece injection molded cover
and salt lid.
 Designed to accommodate mineral tanks without bases or retaining plate.
 Features large salt port opening for easy filling.
 Standard color is almond base with black lid. Other colors available upon
request.
Salt Tank Size (Inches)
For Tank Size
Model No. Capacity
(Dia.” × Height”) L W H
(lbs.)
YCABIN09X18 9×18 100 22.5 13.5 27.25
YCABIN09X24 9×24 125 22.5 13.5 32.50
YCABIN10X35 10×35 225 22.5 13.5 44.00

Potassium Permanganate Feeder

 Individually packaged and tested and assembled with: non-pressurized tank,
injection molded cover (fastened with screws), float valve, polypropylene grid pads,
riser, and overflow.
 Tank composed of blow molded polyethylene with ultraviolet inhibitor.
 Standard color is Blue. Black and Almond available upon request.
 Capacity: 30lb Potassium Permanganate and a liquid capacity of 5 gal
Delivery Capacity Poly Tube Gallons of Riser Pipe
Model No. Float Setting
(oz. of KMNO4 Elbow Size Solution Length
YBT7179-04 2 3/8” ¾ 1 ½” 11”
YBT7179-03 4 3/8” 1 4” 12 ½”
YBT7179-08 6 3/8” 1½ 5 5/8” 12 ½”

Potassium Permanganate
Model No.: X-KMNO4*
Potassium Permanganate Granules, sold in cases of four 5-lb. containers
per case only – 20lbs total.
*Hazardous

Visit us on the web for our complete product line and in-depth technical information. www.appliedmembranes.com
(760) 727-3711• FX: (760) 727-4427
[email protected]

ARE TRADEMARKS OF APPLIED MEMBRANES, INC. © 2014

Page 7-20