CONCRETE STRUCTURES
EN 1992-1-1; 2004: PILE CAP DESIGN
Project : Prepared : FPG
Location : Reviewed : APC
Owner : Approved : TAG
Typical Single Pile Pile Cap ax
Materials
Concrete grade (fcu) : N/mm2
Steel yield strength (fy) : N/mm2
top and side cover (cst) : mm W cy
bottom cover (cb) : mm
cx
L
A. Pile Criteria
Pile
Nominal Pile size (D) : mm
Overhang from pile cap edge to pile face (ax) : mm
Overhang from pile cap edge to pile face (ay) : mm
Compressive Strength of pile (fcu,pile) : N/mm2
Area of pile (Apile) : mm2
Pile Capacity (per pile) (PC, pile) : kN
Pile Cap
Pile Cap Type : 1B
Length (L) : 0.00 mm L =
Width (W) : 0.00 mm W =
Thickness/ Height (H) : mm
Column Dimension
Column Width (cx) : mm
Column Depth (cy) : mm
B. Design Bottom Reinforcement
Load factor (fL) :
Allowable pile eccentricity (ecc.) : mm
Additional moment due to pile eccentricity (Madd) : 0 kN-m Madd =
Factored Total Moment (MU) : 0 kN-m MU =
Effective depth (d) : mm
Resistance Moment Factor (K) :
Lever arm factor (z) :
Categories of Bolted Connections
Design Parameters:
Bolts Class : 5.6
Steel Grade (connected parts) : S 275
Yield Strength of Bolts (fyb) : 300 Mpa Section 3, Part 3.1, Ta
Ultimate Tensile Strength of Bolts (fub) : 500 Mpa Section 3, Part 3.1, Ta
Bearing Strength of connected part (pbs) : 460 Mpa Section 6.3, Clause 6.
Tensile Strength of Bolts (pt) : 0 Mpa Section 6.3, Part 6.3.4
coefficient (standard dimension of holes) (kbs) : 0.7 Section 6.3, Clause 6.
0
Shear Resistance Section 3.6, Part 3.6.1
PS = pS A S
Shear strength of bolts (ps) : 300 Mpa Section 6.3, Part 6.3.1
Shear Area (As) : mm2 Section 6.3, Part 6.3.2
Shear Capacity (Ps) : 0 kN
Bearing Capacity Section 6.3, Part 6.3.3
Pbb = d tp pbb
Nominal diameter of bolt (d) : 1.6 mm
Bearing strength of bolts (pbb) 500 Mpa Section 6.3, Part 6.3.3
Thickness of the connected part (tp) : mm
Bearing Capacity (Pbb) : 0 kN
RETE STRUCTURES
; 2004: PILE CAP DESIGN
Ref.No. : _ _ _ _ _-ST-01
Date : 10-Sep-18
Rev.No. :
ay
(2 x ax) + D
(2 x ay) + D
(PC x ecc.) / 1000
fL x Madd
Section 3, Part 3.1, Table 3.1
Section 3, Part 3.1, Table 3.1
Section 6.3, Clause 6.3.3.3, Table 32
Section 6.3, Part 6.3.4, Table 34
Section 6.3, Clause 6.3.3.3
0
Section 6.3, Part 6.3.1
Section 6.3, Part 6.3.2, Table 30
Section 6.3, Part 6.3.3, Table 31
DESIGN OF REINFORCED CONCRETE (GRAVITY BEAM)
NSCP 2015
Project :
Location :
Girder Label :
Geometry and Material:
Material Data:
f'c = 20.7 MPa compressive strength
fy = 275 MPa yield strength (main bar)
fy (stirruops)
= 275 MPa yield strength (ties)
Section Data:
b = 250 mm beam width
d = 400 mm beam depth
clr. co = 40 mm cover
rebar ø= 20 mm main rebar diameter
rebar ø= 10 mm stirrups/ ties
L = 5 m beam length
Unfactored Loads (Moments):
Support "A" Midspan Support "B"
Dead Load Moments
Negative 41.00 kN-m kN-m 41.00
Postive kN-m 46.00 kN-m
Live Load Moments
Negative 10.00 kN-m kN-m 10.00
Positive kN-m 12.00 kN-m
Factored Loads (Moments):
Support "A" Midspan Support "B"
Negative 41.00 kN-m kN-m 41.00
Postive kN-m 46.00 kN-m
Schedule of Reinforced Concrete Girders (Main Longitudinal)
Section Longitudinal Reinforcements
Girder
Mark Bar Support "A"
Width Depth Loc Midspan
dia continuous
20 TB 2
B-1 250 400
20 BB
Moment Capacity (Mcap):
Support "A" Midspan Support "B"
Top 72.44 kN-m ok 72.44 kN-m ok 72.44 kN-m
Bottom 49.83 kN-m ok 72.44 kN-m ok 72.44 kN-m
Unfactored Loads (Shear):
Support 1m from Support
Dead Load Shear:
63.00 kN 63.00 kN
Live Load Shear:
63.00 kN 63.00 kN
Factored Load Shear (Analysis):
Support 1m from Support
49.83 kN 49.93 kN
Design Shear Vu at Support
Support 1m from Support
Vu = kN kN
Vc = kN kN
Vs = kN kN
S = mm mm
Smax = mm mm
Req'd. = mm mm
Scheddule of Reinforced Concrete Girders (Stirrups)
Section Stirrups/ Ties Spacing
Girder Bar Legs
Mark Width Depth dia No. Spacing No. Spacing
10 100
B-1 250 400 10 2 1 50
ok ok
Recommendation:
USE 1@ 50, 10@ 100, 4@ 200, rest @ 300 to C.L.
TY BEAM)
Support "B"
kN-m
kN-m
kN-m
kN-m
Support "B"
kN-m
kN-m
ments
Support "B"
discontinuous
ok
ok
ps/ Ties Spacing
No. Spacing Rest
4 200 300
ok ok ok
