How to Make a Network Cable

The steps below are general Ethernet Category 5 (commonly known as Cat 5)
cable construction guidelines. For our example, we will be making a Category
5e patch cable, but the same general method will work for making any
category of network cables.

Unroll the required length of network cable and add a little extra wire, just in
case. If a boot is to be fitted, do so before stripping away the sleeve and ensure
the boot faces the correct way. Please note that the cable length should not
be more that 100 meters to prevent attenuation (i.e. degradation of signal
strength due to losses as signal travel down the length of the cable). Keeping
the length within 100 meters from the access point (i.e. face plate) to the patch
panel or network switch will ensure good signal strength/quality.

Carefully remove the outer jacket of the cable. Be careful when stripping the
jacket as to not nick or cut the internal wiring. One good way to do this is to
cut lengthwise with snips or a knife along the side of the cable, away from
yourself, about an inch toward the open end. This reduces the risk of nicking
the wires' insulation. Locate the string inside with the wires, or if no string is
found, use the wires themselves to unzip the sheath of the cable by holding
the sheath in one hand and pulling sideways with the string or wire. Cut away
the unzipped sheath and cut the twisted pairs about 1 1/4" (30 mm). You will
notice 8 wires twisted in 4 pairs. Each pair will have one wire of a certain color
and another wire that is white with a colored stripe matching its partner (this
wire is called a tracer).

Inspect the newly revealed wires for any cuts or scrapes that expose the
copper wire inside. If you have breached the protective sheath of any wire, you
will need to cut the entire segment of wires off and start over at step one.
Exposed copper wire will lead to cross-talk, poor performance or no
connectivity at all. It is important that the jacket for all network cables
remains intact.
Untwist the pairs so they will lay flat between your fingers. The white piece of
thread can be cut off even with the jacket and disposed (see Warnings). For
easier handling, cut the wires so that they are 3/4" (19 mm) long from the
base of the jacket and even in length.

Arrange the wires based on the wiring specifications based on the two
methods set by the TIA, 568A and 568B.
Which one you use will depend on what is being connected. A straight-through
cable is used to connect two different-layer devices (e.g. a hub and a PC). Two
like devices normally require a cross-over cable. The difference between the
two is that a straight-through cable has both ends wired identically with
568B, while a cross-over cable has one end wired 568A and the other end
wired 568B.[1] For our demonstration in the following steps, we will use 568B,
but the instructions can easily be adapted to 568A.
568B-Put the wires in the following  brown
order, from left to right:
 white orange
 orange
 white green
 blue
 white blue
 green
 white brown
 brown
568A - from left to right:
 white/green
 green
 white/orange
 blue
 white/blue
 orange
 white/brown
You can also use the mnemonic 1-2-3-6/3-6-1-2 to remember which wires are
switched.

Press all the wires flat and parallel between your thumb and forefinger. Verify
the colors have remained in the correct order. Cut the top of the wires even with
one another so that they are 1/2" (12.5 mm) long from the base of the jacket, as
the jacket needs to go into the 8P8C connector by about 1/8", meaning that you
only have a 1/2" of room for the individual cables. Leaving more than 1/2"
untwisted can jeopardize connectivity and quality. Ensure that the cut leaves the
wires even and clean; failure to do so may cause the wire not to make contact
inside the jack and could lead to wrongly guided cores inside the plug.

Keep the wires flat and in order as you push them into the RJ-45 plug with the
flat surface of the plug on top. The white/orange wire should be on the left if
you're looking down at the jack. You can tell if all the wires made it into the jack
and maintain their positions by looking head-on at the plug. You should be able
to see a wire located in each hole, as seen at the bottom right. You may have to
use a little effort to push the pairs firmly into the plug. The cabling jacket should
also enter the rear of the jack about 1/4" (6 mm) to help secure the cable once
the plug is crimped. You may need to stretch the sleeve to the proper length.
Verify that the sequence is still correct before crimping.
Place the wired plug into the crimping tool. Give the handle a firm squeeze. You
should hear a ratcheting noise as you continue. Once you have completed the
crimp, the handle will reset to the open position. To ensure all pins are set, some
prefer to double-crimp by repeating this step.

Repeat all of the above steps with the other end of the cable. The way you wire
the other end (568A or 568B) will depend on whether you're making a straight-
through, rollover, or cross-over cable (see Tips).

Test the cable to ensure that it will function in the field. Mis-wired and
incomplete network cables could lead to headaches down the road. In addition,
with power-over-Ethernet (PoE) making its way into the marketplace, crossed
wire pairs could lead to physical damage of computers or phone system
equipment, making it even more crucial that the pairs are in the correct order.
A simple cable tester can quickly verify that information for you. Should you not
have a network cable tester on hand, simply test connectivity pin to pin.

Final assembly of the LAN cable

_______1. Unroll the required length of network cable and add a little extra
wire, just in case.
_______2. Carefully remove the outer jacket of the cable
_______3. Inspect the newly revealed wires for any cuts or scrapes that
expose the copper wire inside
_______4. Untwist the pairs so they will lay flat between your fingers.
_______5. Arrange the wires based on the wiring specifications based on the
two methods set by the TIA, 568A and 568B.

ANSWER KEY
A. IDENTIFICATION

1. 1
2. 2
3. 3
4. 4
5. 5