WALKWAYS and LADDERS

MEYER® Tower Dryer

ME1000S/SG-ME2650S/SG

May 2014 MFH1968-5B

 BROCK® MEYER® Walkways and Ladders

SAFETY First! Recognize SAFETY Information

This symbol is used throughout this Manual to identify particular stages where the bin
Contractor and/or Operator need to take special note and precautions regarding the danger
described in these Instructions. Please read all the SAFETY information and the
instructions completely prior to beginning the construction.
This is the Safety-Alert Symbol. When you see this symbol on your equipment or in this
Manual, be alert to the potential for personal injury.
Signal words DANGER, WARNING, or CAUTION, are used with the Safety-Alert
Symbol. Be sure to follow ALL National and Local Safety Standards governing each
installation site.

Understand Signal Words

DANGER indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, MAY result in minor or
moderate injury.
WARNING! Do not attach yourself to, or carry loose or dangling rope on structures near
or adjacent to the Tower Dryer entry area. Loose rope or material can be
suddenly sucked into the Dryer Fans (which may start automatically). This
can cause equipment damage, severe personal injury or death.

WORK SAFE! While some photographs in this Manual were taken at sites where
certain PPE might not be required, Brock recommends using SAFETY equip-


ment, especially hard hats and SAFETY harnesses—at all installations. ALWAYS
follow appropriate federal, state and local codes for PPR requirements. See Base
Manual MFH1968-1 for recommended PPE.

Use Fall Restraint/Arrest Systems

When working on or inside a Tower Dryer at heights where fall hazards exist, use an
adequate fall restraint or fall arrest system with a lifeline and harness, tied to a secure
point. A proper fall arrest system should withstand 5,400 pounds [2449 kg] of stress
to prevent falling. A fall restraint system typically withstands less than 5400 pounds
and allows a limited fall of about 2' [610]. To ease injury, it is recommended the fall-
distance on restraints be set at 6' [1 829] maximum.
WARNING! Purchase and use secure lifelines and adequate fall restraint/arrest systems. Some
facilities mandate that safety harnesses be used where there is risk of fall and/or
entrapment. Failure to use fall restraint and/or arrest systems consistently when
climbing or entering grain drying towers can cause serious injury or death.

Table of Contents
SAFETY First! Recognize SAFETY Information.........................................................................................2
Understand Signal Words DANGER, WARNING, CAUTION • Use Fall Restraint/Arrest Systems........2
About This Manual...........................................................................................................................................4
Definition of Terms and Symbols • Measurements • Identification of Parts and Hardware ...................4
Ladder SAFETY Procedures ..........................................................................................................................5
Installations While the Tower Is on the Tower Trailer ............................................................................. 6-15
Install Walkways and “Ship Loose” Ladders-and-Cage on the Main Tower ..............................................6
Be Careful Stepping on the Horizontal Tower ............................................................................................6
Order of Walkway Installation ....................................................................................................................7
Bracket Installations .................................................................................................................................7
Walkway/”Catwalk” Arms .................................................................................................................... 8-9
Floor Sections ...................................................................................................................................... 10-11
Upright Posts • Handrails, Upper and Mid .........................................................................................12
2 MFH1968-5B
BROCK® MEYER® Walkways and Ladders

Ladder-and-Cage Installation Basics, Horizontal Tower ....................................................................... 13-14

Outside Ladder Sections • Ladder Splice .................................................................................... 13-14
Cage Hoop Halves .............................................................................................................................. 14
Lift the Tower to “First Stage” to Work Underneath ................................................................................ 15
Types of Walkways ...................................................................................................................................... 16-24
Common Parts in Walkways ...................................................................................................................... 17
Full Walkway (3121-00052).................................................................................................................... 18-19
Partial Walkway (3121-00120), All Models ........................................................................................... 20-21
Eave Platform (3121-00175) Roof Module All Models.......................................................................... 22-23
Eave Platform on the ME1000S - ME1600S ........................................................................................ 24
Outside Ladder-and-Cage Installation ...................................................................................................... 25-35
Ladder-and-Cage Parts Identification......................................................................................................... 25
Top Ladder Extension Through the Eave Platform.................................................................................... 26
Extension Rail Bracing to the MEYER® Roof ......................................................................................... 27
Outside Ladder Brackets to the Tower .................................................................................................... 28-29
Ladder-and-Cage Sections....................................................................................................................... 30-31
Hoop Halves ....................................................................................................................................... 30
Cage Channels ...................................................................................................................................... 31
Bottom Flared Cage Section .................................................................................................................... 32
Outside Bottom Ladder (May Be Pre-Installed)......................................................................................... 33
Locking Ladder Door Assembly 9-41037 ............................................................................................... 34-35
Tie-Back Installation ............................................................................................................................ 35
Diagrams: Outside Walkways and Ladder-and-Cage ............................................................................. 36-55
Outside Ladder-and-Cage Packages ........................................................................................................... 36
Outside Ladder Package Kit Numbers Chart.............................................................................................. 37
ME1000S with 1 Level Catwalk (3121-00084).......................................................................................... 38
ME1200S with 1 Level Catwalk (3121-00085) ...................................................................................... 39
ME1200S with 2 or 3 Level Catwalks (3121-00163)................................................................................ 40
ME1400S with 1 Level Catwalk (3121-00165 ......................................................................................... 41
ME1400S with 2 or 3 Level Catwalks (3121-00166)................................................................................ 42
ME1600S with 1 Level Catwalk (3121-00087) ........................................................................................ 43
ME1600S with 2 or 3 Level Catwalks (3121-00112)................................................................................ 44
ME1800S with 2 Level Catwalks (3121-00088) ....................................................................................... 45
ME1800S with 3 Level Catwalks (3121-00179) ....................................................................................... 46
ME2000S with 2 Level Catwalks (3121-00089) ...................................................................................... 47
ME2000S with 3 Level Catwalks (3121-00113) ....................................................................................... 48
ME2000S with 4 Level Catwalks (3121-00185) ....................................................................................... 49
ME2400S with 3 or 4 Level Catwalks (3121-00091)................................................................................ 50
ME2400S with 5 Level Catwalks (3121-00043) ....................................................................................... 51
ME2650S with 3 Level Catwalks (3121-00176) ....................................................................................... 52
ME2650S with 4 Level Catwalks (3121-00178) ....................................................................................... 53
ME2650S with 4 Level Catwalks (3121-00184) ....................................................................................... 54
Inside Ladder Installations ......................................................................................................................... 55-57
Inside Ladder Sections................................................................................................................................ 55
Internal Service Platform Ladder Access ................................................................................................... 56
Top Inside Ladder Sections ........................................................................................................................ 57
Pre-Installed Inside Ladder Sections .......................................................................................................... 57
Diagrams: Inside Ladders .......................................................................................................................... 58-66
Inside Ladder Package Kit Numbers Chart ................................................................................................ 58
ME1000S ................................................................................................................................................... 59
ME1200S ................................................................................................................................................ 60
ME1400S ................................................................................................................................................... 61
ME1600S ................................................................................................................................................. 62
ME1800S ................................................................................................................................................... 63
ME2000S ................................................................................................................................................... 64
ME2400S ................................................................................................................................................... 65
ME2650S ................................................................................................................................................... 66

MFH1968-5B 3
About This Manual BROCK® MEYER® Walkways and Ladders

About This Manual

The intent of this Manual is to help you follow step-by-step instructions for plumbing
installations in the BROCK® MEYER® Dryer.
IMPORTANT! Pay particular attention to all SAFETY Information in this Manual.
CAUTION! Read and understand this Manual. Failure to follow proper procedures may
cause damage to equipment or personal injury.
Contact your Brock Dealer to replace this Manual should it become lost or damaged.
Store it in a convenient place for easy reference.

Definition of Terms and Symbols

• This Planning Symbol is used in areas where planning needs to take place
before assembly and/or installation can continue.
• “Horizontal,” “vertical,” “bottom,” and “top” refer to the Dryer as it is standing.
The symbols ('') equal inches and (') equals feet in English measurements.

Measurements
The symbols ('') equals inches and (') equals feet in English measurements.
Metric measurements are shown in square brackets following the English
measurement. For example: 15' [4.572 m] 90' [27.432 m]

Identification of Parts and Hardware

• Names for some components which have BROCK® Part Numbers have been capi-
talized throughout this Manual to call attention to them.
• Parts and basic components are identified in Figures and their accompanying Tables
as “Items” with a black number in white circle. See Figure 1 below.
• Hardware is identified by a shaded circle and table item cell.
• Dimensions and lengths are noted with a white circle on an arrow or line, then identi-
fied with numeric values in a Figure Table.
• Pictures may vary slightly from actual components, which may have been modi-
fied for better fit or function.

6 Item Part No. Description

6 U-24016 Ladder Cap
8 U-24142 Extension Rail 54'' [1 372]
43 32 39-20152 Nut, Flange 5/16''-18
38 39-20101 Washer, Flat 5/16 x 1 1/4''
43 39-20322 Bolt, Hex Head 5/16-18 x
1 1/4'' Gr. 5
8 38 32
Figure 1.
Part and Hardware Identification

Hardware Basics:
Organize all hardware so the packages and buckets are easy to locate. When leaving
for the day, remember where you are in the installation, which connections are tight,
and which connections are loose.
IMPORTANT! Always have a second person check the tightening on all Ladder and
Walkway connections!
This Pre-Assemble Symbol (left) suggests that a particular assembly can be finished
ahead of time. Plan to sub-assemble and add hardware any parts that can be prior to
installation. Make sure to use proper hardware.

4 MFH1968-5B
 BROCK® MEYER® Walkways and Ladders Ladder SAFETY Procedures

Ladder SAFETY Procedures

DANGER! Failure to comply with the following instructions may result in death or
serious injury.

IMPORTANT! The Ladder Section with the DANGER Decal (Part No. 13-23790) in Figure 2
at left must be installed as the BOTTOM Section of each Ladder.
1. The WORKING LOAD of the Ladder is 300 lbs [136 kg]. Do not overload.
2. Never climb a damaged or improperly assembled Ladder. Before use, inspect the
Ladder carefully for deterioration from chemicals or weather.
3. Keep the Ladder and Bin away from power lines and live electric wires.
4. Keep rungs free from slippery material such as ice, snow, mud, grease, manure, etc.
5. Wear slip-resistant shoes.
6. DO NOT USE LADDERS if you tire easily, or are subject to fainting spells, or
use medicine or alcohol, or are physically handicapped.
7. FACE THE LADDER when ascending or descending. Maintain a firm grip.
Center your body between Side Rails.
8. Discard and replace the Ladder if it is exposed to fire or damaging chemicals.
9. Never use the Ladder as a horizontal platform, plank or material hoist.
10.Never apply a side load. Never push or pull anything while on the Ladder.
11.Never drop or apply an impact load to the Ladder.
12.Never sit on the ends of Ladder Side Rails.
13.Never use the Ladder as a scaffold.
14. Never use the Ladder when in poor health.
DANGER!
DANGER!
DO NOT enter the Tower Dryer through the Manhole during the filling/
unloading operation or while the Dryer is in use!
When the Dryer and auxiliary equipment are not LOCKED OUT, grain fill may
start at any time without warning.
DO NOT allow the Dryer to run while any adjustments are being made. SHUT
OFF, LOCKOUT and TAGOUT all electrical power BEFORE working on or near
Figure 2. the Dryer. Keep hands, feet, hair, and clothing away from all parts in motion.
Ladder DANGER Decal Failure to shut off, LOCKOUT and TAGOUT power to the Dryer will lead to
13-23790
personal injury or death.

 
Figure 3.
Slippage and Suffocation Hazards in Flowing Grain

at Roof Module

MFH1968-5B 5
Installations While the Tower Is on the Tower Trailer BROCK® MEYER® Walkways and Ladders

Installations While the Tower Is on the Tower Trailer

Install Walkways and “Ship Loose” Ladders-and-Cage
TOWARD TOWER TOP on the Main Tower
Orientation: Remember at all times that the actual TOP of the structure is toward the
cab of the truck. The BOTTOM of the Tower is toward the back end of the truck.
Install all possible Walkways and Side Ladder-and-Cages while the Tower trailer is
horizontal.
Refer to pages 7-15 for installation of 5/16'' hardware on Walkways.
DO NOT TIGHTEN Walkway Handrail or Post connections, as they must be leveled
to vertical after the tower is raised.
IMPORTANT! The lower Partial Walkway (3121-00120, pages 20-21) cannot be installed until the
Tower is raised to vertical.
Cage sections are not pre-installed. Hardware is located in the Ship Loose Bolt Kit.
Refer to pages 25-35 for installation of Outside Ladder-and-Cage hardware/parts.
TIGHTEN all Ladder and Cage connections. They will have to be re-tightened after
the Tower is raised to vertical.

Figure 4. BE CAREFUL Stepping on the Horizontal Tower

Begin on 6' stepladders, and continue the installation stepping only on the screen
Stiffeners (pairs). Remember to step sideways so Screens will not be damaged.

BE CAREFUL!
STEP ONLY on Stringers/Stiffeners! DO NOT
place your weight on the Screens. Step
SIDEWAYS so the Screens will not be
damaged. Use the next Stiffener to pull
yourself up.

Figure 5.
Stand on Stringers Only

6 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Installations While the Tower Is on the Tower Trailer

Order of Walkway Installation

• Walkway Arm Brackets
• Walkway Arms
• Floor Sections
• Vertical Posts
• Handrails
See common parts on page 17.

Figure 6.
Right: Walkway Installation
on Horizontal Tower

Be cautious of personal SAFETY while working on the Tower in this position. Use
an adequate number of ladders.
Bracket Installations
For your convenience, Walkway Arm Brackets (3121-00035), Ladder Brackets, and
some Ladder Sections are pre-installed. Check these Brackets for tightness when the
Dryer is onsite.

4
Figure 8.
L/R Ladder Brackets on Module
as Shipped

2
Item Part No. Description
1 3121-00035 Walkway Arm Bracket
2 Tower, Horizontal
Figure 7. 3 3121-00169 Ladder Bracket-LEFT
Walkway Arm Bracket Pre-Installed on Intermediate 4 3121-00168 Ladder Bracket-RIGHT
Module and Horizontal Tower Module

MFH1968-5B 7
Installations While the Tower Is on the Tower Trailer BROCK® MEYER® Walkways and Ladders

Walkway/”Catwalk” Arms
Consecutive Walkway Arms are bolted into the eleventh and twelfth (11th/12th)
bolt holes from the first set of bolts. There are ten (10) holes between Arms.

Figure 9.
Install Walkway Arms

Attach the Walkway Arms, twelve (12) per Full Walkway, to the pre-installed Arm
Brackets with three (3) 3/8 x 1'' galvanized Hex Head Bolts. Secure with Flange Nuts.
Continue installing Arms around the Tower. Remaining Arms must be installed after
the Tower is raised to vertical.
All Arms must remain loose until all Walkway Floor Sections are attached.

8 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Installations While the Tower Is on the Tower Trailer

When the Walkway is

tightened, tighten this
Bolt first.

1
1

2
3
3

2
2

Item Description
1 Walkway Arm Bracket
2 Walkway Arm
3 Stringer
4 5/16 x 1'' HH Bolt galv
5 5/16'' Flange Nut

Figure 10.
Walkway Arm Installation

MFH1968-5B 9
Installations While the Tower Is on the Tower Trailer BROCK® MEYER® Walkways and Ladders

Floor Sections
IMPORTANT! Do not tighten Walkway Arms until all Floor Sections are connected to form a
complete Walkway around the Tower..

Attach Walkway Floor

sections. Drop in 5/16 x 1''
galvanized Hex Head Bolts,
heads on top of the Walkway.
Secure with Flange Nuts
underneath. Be sure the Floor
Panel (edge) is turned UP,
toward the Tower TOP.

Figure 11.
Floor Sections

5 2
2
TOWARD TOWER TOP

*
3 5
3
3

Item Description
1 Walkway Arm Bracket
2 Walkway Arm
3 Floor Section
4 5/16 x 1’' HH Bolt galv
5 5/16'' Flange Nut

Figure 12.
Walkway Floor Sections

10 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Installations While the Tower Is on the Tower Trailer

TOP VIEW

TO 3 5
WA
RD
4
TO
P

3
3

UNDERSIDE VIEW

Connect adjacent Floor Sections

around the Tower as far as there is
clearance to do so. Detail

Detail
Item Description
1 Walkway Arm Bracket
2 Walkway Arm
3 Floor Section
4 5/16 x 1’' HH Bolt galv
5 5/16'' Flange Nut
TOWARD TOWER TOP

4
5

Figure 13.
Connect Adjacent Floor Sections

MFH1968-5B 11
Installations While the Tower Is on the Tower Trailer BROCK® MEYER® Walkways and Ladders

Upright Posts
Attach the Upright Posts to the outer ends
of the Walkway Arms with four (4) 1''
bolts. Secure with Flange Nuts.

6
Figure 14.
Walkway Posts:
DO NOT TIGHTEN at this time!

Item Description
1 Walkway Arm Bracket
2 Walkway Arm
3 Floor Section
4 5/16 x 1’' HH Bolt galv
5 5/16'' Flange Nut

5 UNDERSIDE DETAIL

Handrails, Upper and Mid

When Vertical Posts are installed, attach Handrails and Handrails between Posts,
Bolt heads inside the Post (same hardware). Repeat Handrail installation all the way
around as far as you can.

Figure 15.
Top and Mid Handrails

12 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Installations While the Tower Is on the Tower Trailer

Ladder-and-Cage Installation Basics, Horizontal Tower

Outside Ladder Sections
Check the tightness of factory-installed Ladder Brackets on the Tower, to be sure they are
still tight after delivery.
Some Ladder sections may already be installed in the Brackets with Locking Clips.

Figure 16.
Locate Pre-Installed Ladder
Brackets and Ladder Sections
on the Tower

Detail

Slide new Ladder Sections through the Ladder Brackets.

Figure 17.
Slide Ladder Sections
Through Brackets

Ladder Splice
1 4
Ladder Sections (3', 4', 5' and 6') are bolted
together using Ladder Rail Splicers 2
(U-23774) with 5/16 x 1’' Gr. 5 Hex Head
Bolts and Flange Nuts.

Item Part No. Description

1 U-23774 Ladder Rail Splicer
2 varies Side Ladder
3 39-20072 Bolt, HHBS 5/16-18 x 3/4'' Gr. 8.2
4 39-20152 Nut, Flange 5/16''-18 3 4

Figure 18.
Ladder Rail Splice
2
MFH1968-5B 13
Installations While the Tower Is on the Tower Trailer BROCK® MEYER® Walkways and Ladders

Secure Ladder Sections with

Locking Clips (in the Bolt
Kit). Be sure the Ladder
DANGER Decal shown in
Figure 2 is right side up.
Figure 19.
Locking Clips and Splices

Cage Hoop Halves

Attach Cage Hoop Halves to the Ladder rail on each side with Locking Clips. Attach
the Hoop Halves in the middle front with hardware from the Bolt Kit. See Details on
pages 30-32.

Figure 20.
Cage Installation
14 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Installations While the Tower Is on the Tower Trailer

Lift the Tower to “First Stage” to Work Underneath

After all possible Walkways and Ladder-and-Cage sections have been installed to the
horizontal Tower Module on the Tower trailer, lift the Tower to the FIRST
STAGE. FIRST STAGE is a partially raised position that allows the remainder of
the full Access Platforms to be installed. After the remaining Access Platform(s)
have been installed, tighten the Platform and Arms.
IMPORTANT! DO NOT TIGHTEN Walkway Arms until all Floor Sections are connected to
make a complete Walkway. DO NOT tighten the Handrails or Upright Posts.
On the ME1000S through
1600S Models, the Tower
Module and Roof Module
are shipped pre-
assembled together and
as one unit on the Tower
trailer. Some Eave
Platform assembly can
be done while the lift
truck is in First Stage lift.

Remaining Ladder-and-
Cage, and Partial Walkway
installations are done after
the Tower and Modules are
raised to vertical.

WARNING!
Use CAUTION when raising the Tower
section to First Stage. Be sure to use all
locking pins specified. Use CAUTION
when raising the Tower section to full
height. Stand clear! Follow all SAFETY
Decals. DO NOT attempt to MOVE the
truck with the hoist/Tower in a raised
position! Protect or LOCK THE
CONTROLS so that no hoist movement
can be made unintentionally. Failure to
follow this instruction could cause death,
serious injury, and/or equipment damage.

Figure 21.
Install Walkways at Tower Trailer FIRST STAGE Lift
MFH1968-5B 15
Types of Walkways BROCK® MEYER® Walkways and Ladders

Types of Walkways

7 2
11
12
12
10

6
11
1
9

3
Figure 22.
Eave Platform 1
(2 Floor Sections) 3121-00175 4
6

10 12
4 3
9
4

2
12

11 3

5
3
Figure 23.
Partial Walkway
2 (3 Floor Sections)
3121-00120
1 1
4 5 1
1
Figure 24.
11 Full OUTSIDE Walkway
12 12 (11 Floor Sections)
3121-00052

3
1

2 3
16 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Types of Walkways

Common Parts in Walkways

10

5
1
9
6
12
4
2 page 24.
Walkway Common Parts
8 11
7
11 8 6 10

10 12 9
6 12
9 2

4
Figure 25.
Eave Platform 3121-00175
3 1
FRONT VIEW

Full Outside Partial Eave

Walkway Walkway Platform
Item Part No. Description Qty. Qty. Qty.
1 3121-00031 Walkway Floor Section 52.75'' 11 3 2
2 3121-00032 Handrail 24 8 6
3 3121-00034 Walkway Arm 12 5 4
4 3121-00035 Walkway Arm Bracket** 12 5 4
5 3121-00055 Walkway Arm Bracket LONG 2
6 3121-00171 Brace, Roof Handrail 21'' 2
7 3121-00172 Brace, Roof Handrail RIGHT 25'' 1
8 3121-00173 Brace, Roof Handrail LEFT 25'' (not shown) 1
9 3121-00174 Platform Roof Mount 2
10 3121-00183 Rail, TPH 33 3/8'' 2
11 3321-00046 Endrail/Handrail External 4 2
12 3321-00035 Vertical Post, 43 1/4'' 12 4
14 *2320-00004 Screw, 5/16-18 x 1’' HWH 198 60
15 *2363-00006 Nut, Flange 5/16''-18 Serr. 198 60
*Hardware in Ship Loose Bolt Kit **This Bracket pre-installed on Tower/Modules

MFH1968-5B 17
Types of Walkways BROCK® MEYER® Walkways and Ladders

FULL Walkway (3121-00052)

FULL Walkways are installed all the way around the Dryer with an opening for the
Ladder-and-Cage. There may be several outside Walkways, depending on the Model.
Refer to Outside Ladder Diagrams on page 36-54 for the number and placement of
Walkways on each different MEYER® model.

12 2

Figure 26.
Full Outside Walkway
3
(11 Floor Sections)
3121-00052
4

1 1
1

Item Part No. Description Qty.

1 3121-00031 Walkway Floor Section 52.75'' 11
2 3121-00032 Handrail 24
3 3121-00034 Walkway Arm 12
4 3121-00035 Walkway Arm Bracket** 12
12 3321-00035 Vertical Post, Walkway 43 1/4'' 12
13 *2320-00004 Screw, 5/16-18 x 1'' HWH 198
14 *2363-00006 Nut, Flange 5/16''-18 Serr. 198
*Hardware in Ship Loose Bolt Kit
**This Bracket pre-installed on Tower/Modules

*
** 3

1
TOP VIEW

Left, Figure 27. 1

ME1600, One (1) Platform

18 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Types of Walkways

First Level Walkway 3121-00052

ONE PLATFORM: Models ME1000S-1600S
Item Part No. Description Qty.
1 3121-00031 Walkway Floor Section 52.75'' 11
2 3121-00032 Handrail 24
3 3121-00034 Walkway Arm 12
4 3121-00035 Walkway Arm Bracket 12
12 3321-00035 Vertical Post 43 1/4'' 12
14 2320-00004 Bolt, 5/16-18 x 1'' HWH Whizlock 198
15 2363-00006 Nut, 5/16''-18 HWH Flange 198
TWO Walkway Assembly 3121-00053
TWO PLATFORMS: Models ME1800S-2000S Standard and
ME1000-1600S Optional
Item Part No. Description Qty.
1 3121-00031 Walkway Floor Section 52.75'' 22
2 3121-00032 Handrail 48
3 3121-00034 Walkway Arm 24
4 3121-00035 Walkway Arm Bracket 24
12 3321-00035 Vertical Post, 43 1/4'' 42
14 2320-00004 *Bolt, 5/16-18 x 1'' HWH Whizlock 396
15 2363-00006 *Nut, 5/16''-18 HWH Flange 396
*Located in the Ship Loose Bolt Kit
THREE Walkway Assembly 3121-00054
THREE PLATFORMS: Models ME2400S Standard
and ME1600S, ME1800-2000S Optional
Item Part No. Description Qty.
1 3121-00031 Walkway Floor Section 52.75'''' 33
2 3121-00032 Handrail 72
3 3121-00034 Walkway Arm 36
4 3121-00035 Walkway Arm Bracket 36
12 3321-00035 Vertical Post, 43 1/4'' 36
14 2320-00004 *Bolt, 5/16-18 x 1'' HWH Whizlock 594
15 2363-00006 *Nut, 5/16''-18 HWH Flange 594
*Located in the Ship Loose Bolt Kit

Figure 28A.
Three Platforms

Figure 28B.
Five Platforms

MFH1968-5B 19
Types of Walkways BROCK® MEYER® Walkways and Ladders

PARTIAL Walkway (3121-00120), All Models

Locate the End Handrail Brace (Item 7) one (1) Screen directly above 3121-00035.
Use Inside Ladder Brace (Item 12, 3121-119) on the inside Screen as a reference. On
the corresponding outside Screen (see Top View), locate the second and third (2nd/
3rd) bolt counter-clockwise from the Screen flange to attach the first Walkway Arm.
Hardware is located in the Ship Loose Bolt Kit. The End Brace of the left Walkway
Floor Panel will mount just outside the Ladder rail below the Hi-Limit Box. There
will be ten (10) bolts between Ladder Brackets.

PARTIAL Walkway
Location Chart 18
Model Height* Module
ME2650S Screen 12 3 3
ME2400S Screen 4 2 11
16 17
ME2200S Screen 3 2
ME2000S Screen 3 2
ME1800S Screen 1 2
ME1600S Screen 3 1B
ME1400S Screen 2 1B
ME1200S Screen 1
ME1000S Screen 2
1B
1A
1 **
*Counting up from bottom of
Module *
TOP VIEW
1

11 3
1 11
5
5 1
3

4
2 11 13
5

12
12
1

3 4

Figure 29.
Partial Walkway (3121-00120)

20 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Types of Walkways

Figure 30.
Partial Walkway Views

The Partial Walkway is built in this

location after the Tower Module has been
raised and connected to the Unload Module.

Item Part No. Description Qty.

1 3121-00031 Walkway Floor Section 52.75'' 3
2 3121-00032 Handrail 8
3 3121-00034 Walkway Arm 5
4 3121-00035 Walkway Arm Bracket** 5
5 3121-00055 Walkway Arm Bracket LONG 2
11 3321-00046 Endrail/Handrail External 4
12 3321-00035 Vertical Post, 43 1/4''
14 *2320-00004 Screw, 5/16-18 x 1'' HWH
15 *2363-00006 Nut, Flange 5/16''-18 Serr.
16 3121-00119 Ladder Chord

MFH1968-5B 21
Types of Walkways BROCK® MEYER® Walkways and Ladders

Eave Platform (3121-00175), Roof Module, All Models

Figure 31.
Eave Platform

16

11
9

6
6 7
11 8

2 10

3
2

Item Part No. Description Qty.

1 1 3121-00031 Walkway Floor Section 52.75'' 2
2 3121-00032 Handrail 6
3 3121-00034 Walkway Arm 4
1 4 3121-00035 Walkway Arm Bracket** 4
6 3121-00171 Brace, Roof Handrail 21'' 2
7 3121-00172 Brace, Roof Handrail RIGHT 25'' 1
12 8 3121-00173 Brace, Roof Handrail LEFT 25'' 1
3
9 3121-00174 Platform Roof Mount 2
Ladder Brackets: Counting from the left/ 10 3121-00183 Rail, TPH 33 3/8'' 2
right, LEFT Ladder Brackets attach at the 11 3321-00046 Endrail/Handrail External 2
6th and 7th Brackets holes from the Wall 12 3321-00035 Vertical Post, 43 1/4'' 4
post. RIGHT Ladder Brackets attach at the 14 *2320-00004 Screw, 5/16-18 x 1'' HWH 60
18th and 19th holes.
15 *2363-00006 Nut, Flange 5/16''-18 Serr. 60
16 9-40969 Ladder Extension: Pages 26-27

22 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Types of Walkways

Install supports for the upright (both

sides). Install the U-shaped Roof Mount
Bracket (Item 9) over the Roof Rib where
the electrical conduit routes and exits
down the Module.

7
6 6

9 9
Figure 32.
Roof Mount Brackets

Connect the Roof Upright Brace (Item 6) to the top of the Bracket.
Connect the top End Handrail (Item 11) to the top of the Brace.
.

11
6
11

6 6

9
8

Figure 33.
Roof Mount End/Back
Connections

MFH1968-5B 23
Types of Walkways BROCK® MEYER® Walkways and Ladders

Eave Platform on the ME1000S Through ME1600S

On the MEYER® ME1000S through ME1600S Models, the Tower Module and
Roof Module are shipped pre-assembled together and as one unit on the lift truck.
Some Eave Platform assembly can be done while the lift truck is in First Stage lift.

11

8
6 7

9 1 1

3 3

Figure 34.
Eave Platform Front View

24 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Outside Ladder and Cage Installation

Outside Ladder and Cage Installation

Ladder-and-Cage Parts Identification

5A
4A 4B 4C
7
1
3
5B

2 6
14
13 9
10

11

Item Part No. Description Figure 35.

1 U-23779 Locking Clip Assembly Ladder and Cage Parts
2 3121-00170 Inside Ladder Bracket (see page 55)
3 U-23774 Ladder Rail Splicer
4A U-00004 4' [1 219] Ladder Section
4B U-00005 5' [1 524] Ladder Section
4C U-00006 6' [1 829] Ladder Section 35
5A 3121-00169 Ladder Bracket-LEFT 33 31
5B 3121-00168 Ladder Bracket-RIGHT
6 U-24016 Ladder Cap 32
7 U-24316 Extension Rail Brace Bracket 36
8 U-24142 Extension Rail 54'' [1 372] O.A.
9 U-24339 Extension Rail Spacer Tube
10 U-23777 Cage Hoop Half
11 432615 Cage Channel 45'' [1 143] (BUNDLE # 292878)
12 field-cut Cage Channel 22'' SHORT (not shown)
13 U-24021 Cage Hoop Expander
14 13-23790 Ladder DANGER Decal (2 per Section)
15 9-42654 BACK Tube, 42 1/8''
16 9-42655 SIDE Tube 38''
31 39-20072 Bolt, 5/16 x 3/4'' BS Gr. 8.2
32 39-20152 5/16'' Flange Nut
33 39-20130 Bolt, 5/16 x 1 1/2'' Hex Head BS Gr. 8.2
35 39-20020 5/16'' Hex Nut
36 39-20070 Bolt, 5/16'' x 1'' Hex Head Gr. 8
37 39-20246 Bolt, Hex Head 5/16-18 x 2 1/2'' Gr. 5
38 39-20101 Washer, Flat 5/16 x 1 1/4''
43 39-20322 Bolt, Hex Head 5/16-18 x 1 1/4'' Gr. 5
44 39-20155 Washer, Weatherseal 5/16''

MFH1968-5B 25
Outside Ladder and Cage Installation BROCK® MEYER® Walkways and Ladders

Top Ladder Extension Through the Eave Platform

Build Ladder Extension Rails (Kit 9-40969, All Models)
Install a pair of 54'' [1 372] Ladder Extension Rails (Item 8) to the 5' Top Ladder Section
(Item 4B) at the Eave. On both the left and right sides of the top Ladder Section, add an
Extension Rail.
Insert the upper 5/16 x 2 1/2'' Hex Head Bolt (Item 37) from inside the Ladder Section through
the Ladder Cap (Item 6) and Spacer Tube (Item 9). Put a Flange Nut (Item 32) on the outside
of the Extension Rail.
Add the same Hardware and Spacer Tube for the lower connection below the Ladder Rung.
See Detail B below.
Top ends of the Side Ladder and Extension Rail are finished with a Ladder Cap. Secure as
shown in Detail A below, adding a 16 ga. Washer (Item 38). Use a 5/16 x 1 1/2'' HHBS Bolt
(Item 33) on top, with a Weatherseal Washer (Item 34) and a Hex Nut (Item 35).

Detail A
6 6 5

FRONT VIEW
32
43 6
35
38 8
43

38 32 6B
8 9
37
Detail B
4B 32
8 31

4B Item Part No. Description

4B U-0-0005 Ladder Section 5'
5A 3121-00169 Ladder Bracket LEFT
5B 3121-00168 Ladder Bracket RIGHT
6 U-24016 Ladder Cap
8 U-24142 Extension Rail 54'' [1 372] O.A.
9 U-24339 Extension Rail Spacer Tube
31 39-20072 Bolt, HHBS 5/16-18 x 3/4'' Gr. 8.2
32 39-20152 Nut, Flange 5/16''-18
35 39-20022 Nut, Hex 5/16''
37 39-20246 Bolt, Hex Head 5/16-18 x 2 1/2'' Gr. 5
38 39-20101 Washer, Flat 5/16 x 1 1/4''
43 39-20322 Bolt, Hex Head 5/16-18 x 1 1/4'' Gr. 5

Figure 36.
(2) Ladder Extensions on Top Ladder Section

26 MFH1968-5B
 BROCK® MEYER® Walkways and Ladders Outside Ladder and Cage Installation

Extension Rail Bracing to the MEYER® Roof

To brace the Extension Rails to the Roof, bolt the Brace Tubes as shown below.
Bolt the flatter ends of two (2) Ladder Back Brace Tubes (Item 15) to the top of the Ladder
Extension Rails (Item 8) as shown in Detail A below.
Bolt the single Ladder Side Brace Tube (Item 16) to the Ladder Extension Rails as shown
in Detail B below.

15 15
29
1 29
7
1
7 Detail B 8
16 16
16
8 7
9 8 15 Side Brace
8 1 Detail B
7 1
9 Back Brace Detail A

15 OR 27
16 30 6

4B 28
7

Detail D
Brace-to-Roof Detail C 2
Secure tops ends of Braces with a Flange Nut (Item 29) on a
Brace Bracket (Item 7) and Locking Clip (Item 1) as shown in
Detail D above.
Bottom ends of Braces connect to the Roof Module. Field drill.
Use a 5/16 x 3/4'' HHBS Bolt (Item 31) on top, with a
Weatherseal Washer (Item 44) between the Brace and Roof,
and a Hex Nut (Item 35) under the Rib. See Detail C above.

Item Part No. Description Qty

1 U-00005 Ladder Assy, 5' 1
2 U-24142 Rail, Ladder Extension Cage 2
3 U-24339 Tube, Cage Ext Rail Spacer 4
6 U-23779 Ladder Locking Clip Assy 4
7 U-24316 Extension Rail Brace Bracket 4
15 9-42654 BACK Tube, 42 1/8'' 2
16 9-42655 SIDE Tube 38'' 2
31 39-20072 Bolt, HHBS 5/16-18 x 3/4'' Gr. 8.2
32 39-20152 Nut, Flange 5/16''-18
35 39-20020 Nut, Hex 5/16''-18
44 39-20155 Washer, Weatherseal 5/16''
Figure 37.
Bracing Ladder Extensions on Top Ladder
Section Through the Eave Platform
MFH1968-5B 27
Outside Ladder and Cage Installation BROCK® MEYER® Walkways and Ladders

Outside Ladder Brackets to the Tower

WARNING! Ladder installations MUST use all specified connecting Brackets to maintain
SAFETY. Failure to follow specific Hardware instructions during assembly
could result in serious operator injury and /or structural damage.
IMPORTANT! Install all Ladder sections with the ROUGH side of the rungs facing
UPWARD and with DANGER Decals right-side-up at the bottom of each
Ladder section.

Item Part No. Description

4 varies Side Ladder
5A 3121-00169 Ladder Bracket LEFT Top 4
5B 3121-00168 Ladder Bracket RIGHT Top
17 varies Grain Sampler Tube 5A
Top Ladder ends: Counting from the left/right,
LEFT Ladder Brackets attach at the 5th and 6th 5B
Brackets holes from the Wall post. RIGHT Ladder
Brackets attach at the 9th and 10th holes.

Detail A

17
4

Detail B

5B
5A

DETAIL C DETAIL A

Mid Ladder areas: Counting from the left/right, LEFT Ladder

Brackets attach at the 10th and 11th Brackets holes from the Wall
post. RIGHT Ladder Brackets attach at the 14th and 15th holes.

Figure 38.
Outside Ladder Brackets

28 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Outside Ladder and Cage Installation

5A 5B

Ladder area at the upper JIC Box: Counting from

the left/right, LEFT Ladder Brackets attach at the 3rd
and 4th Brackets holes from the Wall post. RIGHT
Ladder Brackets attach at the 7th and 8th holes.

Item Part No. Description

4 varies Side Ladder
5A 3121-00169 Ladder Bracket LEFT Top
5B 3121-00168 Ladder Bracket RIGHT Top

5A 5B

Figure 39.
Outside Ladder Brackets

MFH1968-5B 29
Outside Ladder and Cage Installation BROCK® MEYER® Walkways and Ladders

Ladder-and-Cage Sections
Ladder-and-Cage Sections are installed approximately every 44'' [1 118].

Hoop Halves
Connect the Hoop ends to the OUTSIDE VIEW
front side of the Ladder The Cage is begun by joining two (2) Hoop
Extension Rail (refer to Page 31) Halves (Item 10), even with the top of the
6
with Locking Clip assemblies Ladder Extension Rails, above the Eave.
(Item 1), secured on the outside See Detail A.
with Flange Nuts. Overlap the Hoop Halves by aligning the
1 three front holes. See Detail B. Connect
with 5/16 x 3/4'' Hex Head Bin Seal Bolts,
Bolt heads inside, and 5/16'' Hex Nuts,
10 4 32 leaving a Bolt out of the center hole.
Tighten Bolts from the head side.
Detail A

INSIDE VIEW
11 Detail A
31

Detail B
8
35

11 10
Detail B Figure 40.
10 Cage Start at Top of
Build the Extension Rails
top Hoop.

Item Part No. Description 10

1 U-23779 Locking Clip Assembly
4 varies Ladder Section
6 U-24016 Ladder Cap
8 U-24142 Extension Rail 54'' [1 372] O.A. 4
10 U-23777 Cage Hoop Half
11 432615 Cage Channel 45'' [1 143]
31 39-20072 Bolt, 5/16 x 3/4'' BS Gr. 8.2 8
32 39-20152 5/16'' Flange Nut 10
35 39-20020 5/16'' Hex Nut

Build the second Hoop.

Once there are two (2) complete Hoops,
they can be connected with Cage Channels.

10
4
Figure 41.
Second Hoop

30 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Outside Ladder and Cage Installation

Cage Channels
Vertical Cage Channels (Item 11) are shipped
in bundles of eight (8). The Cage has seven (7)
Channels around.
Channels connect outside the Hoop Halves 16
with the same hardware as above, Bolt heads 11
inside. Tighten Bolts from the head side.
Field-cut Channels as needed.

Item Part No. Description

1 U-23779 Locking Clip Assembly
3 U-23774 Ladder Rail Splicer
4 varies Ladder Section 16
6 U-24016 Ladder Cap
10 U-23777 Cage Hoop Half
11 432615 Cage Channel 45'' [1 143] 4
31 39-20072 Bolt, 5/16 x 3/4'' BS Gr. 8.2 31
32 39-20152 5/16'' Flange Nut 35
35 39-20020 5/16'' Hex Nut
Figure 42.
Building the Cage with Hoop Halves and Channels

Continue building the Ladder and

Cage downward. Ladder Sections
are bolted together using Ladder
Rail Splicers U-23774 (Item 3), 5/
16 x 3/4" Gr. 5 Hex Head Bolts and
Flange Nuts (Items 3 and 4).

3 32 5B 10
4
4

5A 1

31 32

Splice Detail
4
4 (Outside View)

10

Figure 43.
Outside Ladder Brackets
MFH1968-5B 31
Outside Ladder and Cage Installation BROCK® MEYER® Walkways and Ladders

Bottom Flared Cage Section

Build the bottom Flare Hoop by connecting the two (2) Hoop Halves (Item 10) with
an Expander section (Item 13) in between, using 5/16 x 3/4'' Hex Head Bin Seal Bolts
(heads inside) and Hex Nuts. The ends of bottom Hoop Halves attach to the back
edge (next to the bin wall) of the Ladder Rail with a Locking Clip Assembly, with
Bolt Heads inside.

Item Part No. Description

1 U-23779 Locking Clip Assembly
4 varies Ladder Section
6 U-24016 Ladder Cap
10 U-23777 Cage Hoop Half
11 432615 Cage Channel 45'' [1 143]
13 U-24021 Cage Hoop Expander
10 31 39-20072 Bolt, 5/16 x 3/4'' BS Gr. 8.2
4 32 39-20152 5/16'' Flange Nut
35 39-20020 5/16'' Hex Nut
10

11

13

10
4
1 10

10

32
31
TOP HOOP CONNECTION DETAIL
35
11
4 10 11
1

10
10
Figure 44.
32 Bottom Flared Section

FLARE HOOP CONNECTION DETAIL

4 FRONT VIEW

13

32 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Outside Ladder and Cage Installation

Outside Bottom Ladder (May Be Pre-Installed)

The Ladder section on the Unload Base Module will be needed for access throughout
the installation.

Figure 45.
Bottom Ladder and Access Door

Figure 46.
44.
Bottom Ladder at Unload Module

MFH1968-5B 33
Outside Ladder and Cage Installation BROCK® MEYER® Walkways and Ladders

Locking Ladder Door Assembly 9-41037

This Door is installed on the

bottom Outside Ladder section at
the Unload. Plan whether your
Ladder Door is to be LEFT- or
Install locking RIGHT-opening before attaching
the Door assembly to the Ladder.
devices to reduce The Door may be secured with a
the risk of padlock (not included).
unauthorized
access at tower
points of entry.

Figure 47.
Locking Ladder Door
9-41037

1. Bolt the Upper and Lower Hinge Assemblies (Item 2) to the

Door (Item 1) with two 5/8'' Carriage Bolts (Item 5) (heads 5 Detail A
outside) and Lock Nuts (Item 8) inside. See Detail A at right.
2. Install the Handle (Item 4) on the Door with two 5/16'' Bin
Seal Bolts (Item 7), heads outside and Lock Nuts 2
(Item 8) inside.
3. Bolt the two Hinge Assemblies to the Ladder Rail with two
5/16'' Hex Head Bolts (Item 6), heads toward inside of the
Ladder, and Lock Nuts (Item 8). See Detail A. Detail B
4. Bolt the Lock Bracket (Item 3) to the opposite Ladder Rail. 1
It is installed either above or below the Door Handle. Use
two 5/16'' Hex Head Bolts (Item 6), heads inside the Ladder,
and Lock Nuts (Item 8). The Lock Bracket flange should be
turned toward the back (bin side) of the Ladder, to line up 4
with one of the round holes in the Door.

Item Part No. Description Qty. 8

1 9-41007 Door, Bin Ladder 1
2 9-41034 Hinge Assembly 2 9
3 9-41006 Bracket 1
4 3-12194 Handle 1
5 Ladder 2
6 8282 5/16 - 18 x 5/8'' Carriage Bolt, Gr. 5 4
7 4412-1 5/16 - 18 x 5/8'' Hex Head Bolt, Gr. 5 6
8 39-20072 5/16 - 18 x 3/4'' Bin Seal Bolt, Gr. 8.2 2
9 39-20024 5/16'' - 18 Lock Nut 12
Figure 48.
Locking Ladder Door

34 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Outside Ladder and Cage Installation

8
Item Part No. Tie-Back Hardware Qty.
7 6 5 7 B Dryer Sidewall 1
9 9 D Door (open) 1
1 3-11214 Chain 2'
2 4270 S-Hook 2
3 3-11212 Spring Extension 1
1 4 39-20120 5/16'' Eyebolt 1
5 39-20155 5/16'' Weatherseal Washer 1
6 39-20020 5/16'' Hex Nut 2
2

5 3 Figure 49.
Lock Bracket Detail
FRONT VIEW

Tie-Back Installation:
The Door in its “open” position uses a Tie-Back Chain/Spring assembly.
1. Attach an S-Hook to each end of the Tie-Back Chain. Put one S-Hook in a
Lock hole in the Door. Adjust length and tension.
2. Locate the bin vertical seam nearest the hinge side of the Ladder, (or field-
drill a hole nearer the Ladder). In feed bins, use any available hole in a Ladder
Standoff Rail, X-Brace, or Leg.
3. Replace regular seam hardware, from the outside, with: the Eyebolt, 5/16'' Hex
Nut, and Weatherseal Washer. Use a second Hex Nut inside.
To lock, close the Door. Insert a padlock or locking device (not provided).

To reduce the risk of SIDE VIEW

unauthorized entry to
the Dryer, the Owner/
Operator should install B 4
PADLOCKS wherever 5
appropriate, especially
on Access Doors in the
Cooling Floor /
Plenum, the Roof
Manhole, and any other
point of entry. Install
Locks on Electrical
Cabinets and the Figure 50.
Disconnect Handle. Chain and Eyebolt Detail 6 OUTSIDE

FRONT VIEW
D B

5
2 1
3 6
2

Figure 51.
Padlock Suggestion (Owner-Supplied) for LOOP
Locking Ladder Door and Disconnect Handle

MFH1968-5B 35
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

Diagrams: Outside Walkways and Ladder-and-Cage

Outside Ladder-and-Cage Packages

Tower Description Part No.
ME1000 with 1 Level Walkway 3121-00084
ME1200 with 1 Level Walkway 3121-00085
ME1200 with 2 or 3 Level Walkways 3121-00163
ME1400 with 1 Level Walkway 3121-00165
ME1400 with 2 or 3 Level Walkways 3121-00166
ME1600 with 1 Level Walkway 3121-00087
ME1600 with 2 or 3 Level Walkways 3121-00112
ME1800 with 2 Level Walkways 3121-00088
ME1800 with 3 Level Walkways 3121-00179
ME2000 with 2 Level Walkways 3121-00089
ME2000 with 3 Level Walkways 3121-00113
ME2000 with 4 Level Walkways 3121-00185
ME2400 with 3 or 4 Level Walkways 3121-00091
ME2400 with 5 Level Walkways 3121-00043
ME2650 with 3 Level Walkways 3121-00176
ME2650 with 4 Level Walkways 3121-00178
ME2650 with 5 Level Walkways 3154-00184

36 MFH1968-5B
MFH1968-5B

BROCK® MEYER® Walkways and Ladders

MEYER® Model: 1000 1200 1400 1600 1800 2000 2400 2650
Outside Ladder Package Kit No. 3121- 3121-
00084 00085
3121-
00163
3121- 3121- 3121- 3121- 3121-
00165 00166 00087 00112 00088
3121-
00179
3121- 3121- 3121- 3121- 3121- 3121-
00089 00113 00185 00091 00176 00178
Number of Tower Walkway Levels 1 1 2 or 3 1 2 or 3 1 2 or 3 2 3 2 3 4 3 or 4 3 4
U-23777 Cage Hoop Half
U-24021 Cage Hoop Expander
292878 Channel Bundle of 8
9-40969 Kit, Ladder Cage Extension
3121-00168 Ladder Standoff Bracket-RIGHT 3 3 4 4 4 5 6 10 8 10 10 11 13 15 15
3121-00169 Ladder Standoff Bracket-LEFT 3 3 4 4 4 5 6 10 8 10 10 11 13 15 15
U-23779 Locking Clip Assembly 6 6 8 8 8 10 12 14 10 14 14 22 14 14 12
U-23774 Ladder Rail Splicer 2 2 4 4 4 6 4 6 4 6 6 8 8 8 8
U-00006 6' Ladder Assembly 1 3 3 3 3 3 1 2 2
U-00005 5' Ladder Assembly 2 2 3 3 3 1 2 2 2 2 6 3 1 1
U-00004 4' Ladder Assembly 2 2 2 3 2
*2363-00006 Nut, 5/16''-18 Flange HWH Serr. 10 10 16 16 16 22 20 26 18 26 16 26 30 28
*2320-00004 Bolt, 5/16-18 x 1'' HWH Whizlock zc 4 4 8 8 8 12 8 12 8 12 12 12 16 16
* Additional quantities in Ship Loose Bolt Kit below
Ship Loose Kits
U-23777 Cage Hoop Half 16 18 18 22 20 24 20 24 24 28 28 28 30 32 32
U-24021 Cage Hoop Expander 3 3 4 3 4 3 4 3 4 4 5 6 5 5 6

Diagrams: Outside Walkways and Ladder-and-Cage

292878 Channel Bundle of 8 5 6 5 8 6 9 6 8 6 10 9 8 10 11 11
9-40969 Kit, Ladder Cage Extension 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3121-00168 Ladder Standoff Bracket-RIGHT 8 9 8 8 8 8 8 6 6 7 7 12 8 6 7
3121-00169 Ladder Standoff Bracket-LEFT 8 9 8 8 8 8 8 6 6 7 7 12 8 6 7
U-23779 Locking Clip Assembly 32 36 34 38 36 40 36 42 42 48 48 52 58 60 64
U-23774 Ladder Rail Splicer 10 14 12 12 12 14 14 12 14 16 16 18 18 20 20
U-00006 6' Ladder Assembly 1 1 2 1 2 2 3 3 2 3 1 1
U-00005 5' Ladder Assembly 5 5 4 6 5 6 4 4 5 2 2 5 7 8 10
U-00004 4' Ladder Assembly 3 3 2 3 1 1 4 4 1 3 3
3165-00046 Bottom Ladder (for Unload Module) 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1
3154-00033G01 Ship Loose Bolt Kit G01 G01 G02/11 G01 G02 G03 G03 G05 G06/13 G07 G08 G17
2363-00006 Nut, 5/16''-18 Flange HWH Serr. 122 142 138 164 154 165 159 168 174 231 210 190 177 275 300
2320-00004 Bolt, 5/16-18 x 1'' HWH Whizlock zc 90 106 104 126 118 125 159 126 132 181 160 163 177 170 200
37
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

ME1000S
24

22
10

4B

21

23 Item Part No. Description

4A U-00004 4' [1 219] Ladder Section
4B U-00005 5' [1 524] Ladder Section
4B 4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
6 8 Cage Channel 22''
6 9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
9
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
4C 24 Walk-Through
4B 25 Leg 1'' Ladder Position
26 varies Inside ladder

20 20

23

4B
Figure 52.
Outside Ladders and Cages on ME1000S
with 1 Level Catwalk
(3121-00084)

38 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

ME1200S 24 NOTE: This group of Ladder and Safety

25 Cage parts is located at the “Leg 1” position
(shown here for clarity)

22

SHIP LOOSE 4A
All Ladders,
Brackets and
Splices from this 26
point down, both SHIP LOOSE
sides Brackets and Ladders this section only

4B
4B
Item Part No. Description
4A U-00004 4' [1 219] Ladder Section
21 4B U-00005 5' [1 524] Ladder Section
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
4B
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
6 6 9 23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside ladder

4B 4A

20
6 6
7

23
6 6 9

Figure 53.
4B*
Outside Ladders and Cages on ME1200S
with 1 Level Catwalk
(3121-00085)

MFH1968-5B 39
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

ME1200S NOTE: This group of Ladder and Safety

Cage parts is located at the “Leg 1” position
24 (shown here for clarity)
25
SHIP LOOSE
All Ladders,
Brackets and
Splices from this 22 8
point down, both
sides
SHIP LOOSE
4B 4A Brackets and Ladders
this section only

4B
26

Item Part No. Description

4A U-00004 4' [1 219] Ladder Section
4B U-00005 5' [1 524] Ladder Section
5' [1 524] Ladder Section
4B* U-00005 (called
4B out, loose assy.)
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
21 10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
4B 22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside ladder

4A
4B

20
6 6

7
23 6 6 9
Figure 54.
Outside Ladders and Cages on ME1200S
4B* with 2 or 3 Level Catwalks
(3121-00163)

40 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

24 NOTE: This group of Ladder and Safety

ME1400S 25 Cage parts is located at the “Leg 1” position
(shown here for clarity)

22

4B
26
SHIP LOOSE
Brackets and Ladders
4B 4C this section only

21
4B

4B Item Part No. Description

4B U-00005 5' [1 524] Ladder Section
4B 5' [1 524] Ladder Section
4B* U-00005 (called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
9 U-24021 Cage Hoop Expander
4B 10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside ladder
4B
4B 4B

20
6 6

23 7

6 6
SHIP LOOSE
All Ladders,
Brackets and 7
Splices from this
point DOWN, 6 6 9
BOTH SIDES
4B*
Figure 55.
Outside Ladders and Cages on ME1400S
with 1 Level Catwalk
(3121-00165)

MFH1968-5B 41
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

24 NOTE: This group of Ladder and Safety

ME1400S 25 Cage parts is located at the “Leg 1” position
(shown here for clarity)

22

4B
26

4B
4C
SHIP LOOSE
Brackets and Ladder this
section only
21
4B

Item Part No. Description

4B U-00005 5' [1 524] Ladder Section
5' [1 524] Ladder Section
4B* U-00005 (called out, loose assy.)
4B
4C U-00006 6' [1 829] Ladder Section
6 U-23777 Cage Hoop (Half)
21 7 432615 Cage Channel 45'' [1143]
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
4B 23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside Ladder
4B

4C
4B
4B
20
6 6

23 7
6 6
7
SHIP LOOSE
All Ladders,
Brackets and 6 6 9
Splices from this
point DOWN,
BOTH SIDES
4B*
Figure 56.
Outside Ladders and Cages on ME1400S
with 2 or 3 Level Catwalks
(3121-00166)

42 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

NOTE: This group of Ladder and Safety

ME1600S 25
24 Cage parts is located at the “Leg 1” position
(shown here for clarity)

22

26 4B
SHIP LOOSE
Brackets and Ladder this
section only
4A
4C

21 Item Part No. Description

4A U-00004 4' [1 219] Ladder Section
4B U-00005 5' [1 524] Ladder Section
4A 4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
4B 22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside Ladder

4B

4B
4B
20
6 6
23 7

SHIP LOOSE 6 6
All Ladders,
Brackets and 7
Splices from this
point DOWN, 6 6 9
BOTH SIDES
4B*
Figure 57.
Outside Ladders and Cages on ME1600S
with 1 Level Catwalk
(3121-00087)
MFH1968-5B 43
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

NOTE: This group of

ME1600S Ladder and Safety Cage 24
parts is located at the 25
“Leg 1” position (shown
here for clarity)
22
SHIP LOOSE
Brackets and Ladder this
section only 4A
26

Item Part No. Description

4A Ladder Section, 4' 4A
4B U-00005 5' [1 524] Ladder Section 4C
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section 21
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway 4B
22 3121-00175 Eave Platform 4C
23 3121-00034 Walkway Arm
24 Walk-Through 21
25 Leg 1'' Ladder Position
26 varies Inside Ladder 10

4C
SHIP LOOSE
All Ladders,
Brackets and
Splices from this
point DOWN,
BOTH SIDES

4B 4B

20
6 6

23 7
10
6 6

7
This Bracket to be installed on
the Tower

4B*
Figure 57.
6
Outside Ladders and Cages on ME1600S
with 2 or 3 Level Catwalks 6
(3121-00112) 9

44 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

ME1800S NOTE: This group of Ladder and

Safety Cage parts is located at the “Leg
1” position (shown here for clarity) 24
25
SHIP LOOSE
Ladders from
22 this point UP

26
4A
4C
10 4B

Item Part No. Description

4A Ladder Section, 4’
4B U-00005 5' [1 524] Ladder Section
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.) 4C
4C U-00006 6' [1 829] Ladder Section
6 U-23777 Cage Hoop (Half) 4B 4C
7 432615 Cage Channel 45'' [1143]
9 U-24021 Cage Hoop Expander 21
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway 4C
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through 4B
25 Leg 1'' Ladder Position
26 varies Inside Ladder

4B
SHIP LOOSE
All Ladders, Brackets
and Splices from this
point DOWN, BOTH 4B
SIDES 4B
20

23
4C
Figure 58.
Outside Ladders and Cages on ME1800S 6 6
with 2 Level Catwalks
7
(3121-00088)
6
6
4B* 9

MFH1968-5B 45
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

ME1800S

24 NOTE: This group of Ladder and

25
Safety Cage parts is located at the “Leg
1” position (shown here for clarity)

22
SHIP 26
LOOSE
Ladders 4B
from this 4C
4A
point UP
21 Item Part No. Description
SHIP LOOSE 4A Ladder Section, 4’
4C 4B U-00005 5' [1 524] Ladder Section
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
4C
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
21 20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
4C 22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
SHIP LOOSE 25 Leg 1'' Ladder Position
All Ladders, 26 varies Inside Ladder
Brackets and 4C
Splices from
this point
DOWN, 21 4B
BOTH SIDES

4B

20
4B Figure 59.
Outside Ladders and Cages on ME1800S
23 with 3 Level Catwalks (option)
(3121-00179)
4B
6 6
7
6 6 9

4B*

46 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

NOTE: This group of Ladder

ME2000S and Safety Cage parts is
located at the “Leg 1” position 24 25
(shown here for clarity)
22
4C

26

SHIP LOOSE
Ladder Bracket here 4A
10
4C
21
SHIP LOOSE
Brackets and Ladders from
this point UP, BOTH SIDES

4C
Item Part No. Description
4A U-00004 4' [1 219] Ladder Section
4B U-00005 5' [1 524] Ladder Section
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
4C 4C
4C U-00006 6' [1 829] Ladder Section 21
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway 4B
21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside Ladder
4A
SHIP LOOSE 4B
All Ladders, Brackets
and Splices from this 20
point DOWN, BOTH 6 6
8
23 6 6
7
4C
6 6

Figure 60. 7
Outside Ladders and Cages on ME2000S
with 2 Level Catwalks
6
6
(3121-00089)
9
4B*

MFH1968-5B 47
 Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

ME2000S NOTE: This group of Ladder and Safety

10 SHIP LOOSE Cage parts is located at the “Leg 1” position
Ladder Bracket here
(shown here for clarity)
24
25
22
4C

26

10
SHIP LOOSE
Ladder Bracket here 4A

4C
21
SHIP LOOSE
All Ladders from this point UP,
BOTH SIDES
4C
Item Part No. Description
4A U-00004 4' [1 219] Ladder Section
4B U-00005 5' [1 524] Ladder Section
5' [1 524] Ladder Section 4C 4C
4B* U-00005 (called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section 21
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway 4B
21
21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside Ladder 4A
4B
SHIP LOOSE 20
All Ladders, Brackets 6 6
and Splices from this 8
point DOWN, BOTH 6 6
SIDES 23 7
4C
6 6
Figure 61.
7
Outside Ladders and Cages on ME2000S
with 3 Level Catwalks 6
(3121-00113) 6
9
4B*

48 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

ME2000S NOTE: This group of Ladder and Safety

Cage parts is located at the “Leg 1” position
(shown here for clarity)

24
25
22

4C 26

4A
SHIP LOOSE 4A
All Ladders from this point UP,
BOTH SIDES
4B

21
Item Part No. Description 4A
4B
4A U-00004 4' [1 219] Ladder Section
4B U-00005 5' [1 524] Ladder Section
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.) 4B
4C U-00006 6' [1 829] Ladder Section
6 U-23777 Cage Hoop (Half) 4B 4A
7 432615 Cage Channel 45'' [1143] 4B
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
4B
21 3121-00052 Full Walkway 4B
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside Ladder
4A
4B
SHIP LOOSE 20
All Ladders, Brackets 6 6
and Splices from this 8
point DOWN, BOTH 6 6
SIDES 23
7
4C
6 6
Figure 62. 7
Outside Ladders and Cages on ME2000S
with 4 Level Catwalks 6 6 9
(3121-00185)

4B*

MFH1968-5B 49
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

NOTE: This group of Ladder and Safety

ME2400S 25 24 Cage parts is located at the “Leg 1” position
(shown here for clarity)
22
4B

10
26

4B 4C
SHIP LOOSE
21 10 Ladders, Brackets
here
4C
10

4A
4C

21
4B All Ladders, Brackets and
All Ladders, Splices SHIP LOOSE from
Brackets and Splices this point UP, BOTH SIDES
SHIP LOOSE from
this point DOWN, Item Part No. Description
BOTH SIDES 4B U-00005 5' [1 524] Ladder Section
4B 5' [1 524] Ladder Section
4B* U-00005 (called
4C out, loose assy.)
4C U-00006 6' [1 829] Ladder Section
21 6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
4A 8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
4B 4B 25 Leg 1'' Ladder Position
26 varies Inside Ladder
20
6 6
23 7
6 6
7 4B
6 6
7
6 6 9
Figure 63.
4B* Outside Ladders and Cages on
ME2400S with 3 or 4 Catwalks
(3121-00091)

50 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

NOTE: This group of Ladder and Safety

ME2400S 25 24 Cage parts is located at the “Leg 1” position
(shown here for clarity)
5 Catwalks
22
4B
26
10

4B
4C SHIP LOOSE
10 Ladders, Brackets
21 here

4B
10
4A
4C

21
All Ladders, Brackets and
Splices SHIP LOOSE from
this point UP, BOTH SIDES
4B
4B Item Part No. Description
4B U-00005 5' [1 524] Ladder Section
21
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section
6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
4B
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
21 10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
All Ladders, 21 3121-00052 Full Walkway
Brackets and 22 3121-00175 Eave Platform
Splices SHIP 23 3121-00034 Walkway Arm
LOOSE from this 24 Walk-Through
point DOWN,
BOTH SIDES 25 Leg 1'' Ladder Position
4B 26 varies Inside Ladder
20
6 6
7
23
6 6
4B
7
6 6
7
6 9 6
Figure 64.
4B* Outside Ladders and Cages on
ME2400 with 5 Catwalks
(3121-00043)
MFH1968-5B 51
Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

24 NOTE: This group of Ladder and Safety

ME2650S 25 Cage parts is located at the “Leg 1” position
(shown here for clarity)

22
4C Item Part No. Description
26 4B U-00005 5' [1 524] Ladder Section
SHIP LOOSE 5' [1 524] Ladder Section
4B* U-00005 (called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section
3121-00168
3121-00169 6 U-23777 Cage Hoop (Half)
4B 7 432615 Cage Channel 45'' [1143]
4B 8 Cage Channel 22''
21 9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
20 3121-00120 Partial Walkway
21 3121-00052 Full Walkway
4B 22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
4B 24 Walk-Through
25 Leg 1'' Ladder Position
Shipping 26 varies Inside Ladder
Tower 4B
4A 21 SHIP LOOSE from
this point UP

20 4A
6 6
4C
7

4A 4C 6 6
4B
7
21
4A 6 6
7
23
6 6
4A 7
6
6
4B* 9

4B
4B*
4A
4B 20
4A All Ladders, Brackets and Splices shown above
6 6 SHIP LOOSE; bottom (2) 5' Ladders (4B*)
called out in Base assembly.
7
All Ladders,
Brackets and 6 6
Splices SHIP 4B Figure 65.
LOOSE from this 7 Outside Ladders and Cages on
point DOWN, ME2650S with 3 Catwalks
BOTH SIDES 6 6 (3121-00176)

52 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

NOTE: This group of Ladder and Safety

ME2650S Cage parts is located at the “Leg 1” position
(shown here for clarity)
24
25

22
4B Item Part No. Description
26
4B U-00005 5' [1 524] Ladder Section
4B* U-00005 5' [1 524] Ladder Section
(called out, loose assy.)
4C U-00006 6' [1 829] Ladder Section
4B 6 U-23777 Cage Hoop (Half)
21 7 432615 Cage Channel 45'' [1143]
4C 8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
4C 20 3121-00120 Partial Walkway
4B 21 3121-00052 Full Walkway
21 22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
24 Walk-Through
25 Leg 1'' Ladder Position
4A 4B 26 varies Inside Ladder
SHIP LOOSE
from this
point UP
4C 4A
4C 21 20
All Ladders, 6 6
Brackets and
Splices SHIP 4B
LOOSE from 7
4C this point
DOWN, 6 6
BOTH SIDES
7
4A 4B
6 6
21 7
6 6
4A
4B* 9
23

4B*
4B
All Ladders, Brackets and Splices shown above
4A SHIP LOOSE; bottom (2) 5' Ladders (4B*)
called out in Base assembly.
4B
20
4A Figure 66.
Outside Ladders and Cages on
ME2650S with 4 Catwalks
(3121-000178)
SHIP LOOSE
from here down 6 6

MFH1968-5B 53
 Diagrams: Outside Walkways and Ladder-and-Cage BROCK® MEYER® Walkways and Ladders

NOTE: This group of Ladder and Safety Cage parts is

ME2650S located at the “Leg 1” position (shown here for clarity)
Item Part No. Description
25 24 4B U-00005 5' [1 524] Ladder Section
5' [1 524] Ladder Section
4B* U-00005 (called
22 out, loose assy.)
26 4C U-00006 6' [1 829] Ladder Section
4B 6 U-23777 Cage Hoop (Half)
7 432615 Cage Channel 45'' [1143]
8 Cage Channel 22''
9 U-24021 Cage Hoop Expander
10 varies Side Ladder Bracket
4B 4C
20 3121-00120 Partial Walkway
21 21 3121-00052 Full Walkway
22 3121-00175 Eave Platform
23 3121-00034 Walkway Arm
4B
24 Walk-Through
25 Leg 1'' Ladder Position
26 varies Inside Ladder
4A
4C All Ladders, Brackets and
21 Splices SHIP LOOSE from
this point UP, BOTH SIDES
4B

4B

4B 21 6 6
7
6 6
4B
7
4B
6 6
All Ladders,
Brackets and 21 7
Splices SHIP
LOOSE from 6 9 6
this point
DOWN, BOTH
SIDES 23 4B*

4C 4B
All Ladders, Brackets and Splices shown above
20 SHIP LOOSE; bottom (2) 5' Ladders (4B*)
6 6 called out in Base assembly.
7
6 6
Figure 67.
7 4B Outside Ladders and Cages on
6 6 ME2650S with 4 Catwalks
(3121-000184)

54 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Inside Ladder Installations

Inside Ladder Installations

Inside Ladder Sections
Inside Ladder sections are mounted on Ladder Chords.
While the same Locking Clip Assembly is used to attach the Ladder Bracket to the
Ladder Rail, the Inside Ladder Bracket 3121-00170 differs from Outside Brackets.
Be sure Ladder DANGER Decal 13-23790 (left) on each Ship-Loose Ladder section
to be installed is readable right-side-up when the Tower is upright.
WARNING! Ladder installations MUST use all specified connecting Brackets to maintain
SAFETY. Failure to follow specific Hardware instructions during assembly
could result in serious operator injury and /or structural damage.

5
Attach the Ladder to the Bracket on both
sides, using the Ladder Clips. 6

IMPORTANT!
Install all Ladder sections with
the ROUGH side of the rungs
facing UPWARD and with Item Part No. Description
DANGER Decals right-side- 1 varies Inside Ladder (location)
up at the bottom of each
Ladder section. 2 3121-00170 Inside Ladder Bracket
Splice sections together. See 4 varies Inside Screen
Figure 18 on page 13. 5 3121-00170 Inside Ladder Clip
6 U-23779 Locking Clip

4 1
6 2
4
2

Figure 68.
Inside Ladder Bracket and Ladder Clips
MFH1968-5B 55
Inside Ladder Installations BROCK® MEYER® Walkways and Ladders

Internal Service Platform Ladder Access

Continue the Inside Ladder-and-Cage installation through the Inside Service
Platform opening in the Tower.

Figure 69.
Inside Ladder Through the Service Platform Opening
Figure 70.
Inside Ladder with Cage

2
2 Finish the access area by
installing Safety Rails.

2 2

1 1

Item Part No. Description

Figure 71.
1 3121-00153 Post, Work Platform
Rails at Service Platform Ladder Access 2 3121-00154 Handrail, Work Platform

56 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Inside Ladder Installations

Top Inside Ladder Sections

IMPORTANT! You must field-install the Ladder section above the #3 Inside Service
Platform. There are four (4) Ladder splices above and below the Platform.

Figure 72.
Top Inside Ladder Installation in the Tower

Special Note on Model 2650:

The 60'' distance between the Inside Service Platform and where the Inside Ladder
must be mounted is a difficult reach. take a 2' or 3' stepladder up with you to help
make the task easier.
Pre-Installed Inside Ladder Sections

The Upper Inside Ladder section is factory-

installed, as well as the Ladder section attached
to the Air Duct.

Item Description
1 Ladder Section
2 Air Duct 2 1
3 Duct Access Door
4 Bracket 3121-00182

Figure 73.
Inside Ladder at Air Duct (LP
Model shown), Pre-Installed

MFH1968-5B 57
Diagrams: Inside Ladders BROCK® MEYER® Walkways and Ladders

Diagrams: Inside Ladders

MEYER® Model: 1000 1200 1400 1600 1800 2000 2400 2650
INSIDE Ladder Package 3121- 3121- 3121- 3121- 3121- 3121- 3121- 3121-
Kit Number 00123 00124 00167 00126 00127 00128 00130 00177
3121-00170 Bracket Ladder Attachment 12 16 20 24 20 20 18 18
U-23779 Locking Clip Assembly 12 16 20 24 20 20 18 18
U-23774 Ladder Rail Splicer 6 6 8 10 10 8 8 8
U-00006 6' Ladder Assembly 2 1 3
U-00005 5' Ladder Assembly 2 2 4 6 4 2 5 5
U-00004 4' Ladder Assembly 2 2
2320-00004 *Bolt, 5/16-18 x 1'' HWH Whizlock 22
*2320-00010 Bolt, 5/16-18 x 5/8'' Hex Fla 24 28 36 44 40 36 34 34
*2363-00006 Nut, 5/16''-18 Flange HWH Serr. 36 44 56 68 60 56 52 52
* Additional quantities in Ship Loose Bolt Kit below
Ship Loose Kits
3121-00170 Bracket Ladder Attachment 6 6 8 8 12 16 36 28
U-23779 Locking Clip Assembly 6 6 8 8 12 16 26 28
U-23774 Ladder Rail Splicer 2 2 2 2 4 8 10 14
U-00006 6' Ladder Assembly 1 1 2 1 3 1
U-00005 5' Ladder Assembly 1 1 1 3 5
U-00004 4' Ladder Assembly 1 1 1 4 2
U-00003 3' Ladder Assembly 1
Ship Loose Bolt Kit
2320-00010 Bolt, 5/16-18 x 5/8'' Hex Fla 10 12 12 20 32 46 56
2363-00006 Nut, 5/16''-18 Flange HWH Serr. 16 20 20 32 48 72 84''

58 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Inside Ladders

ME1000S

1 Item Part No. Description

1 3121-00122 Ladder Chord, 10''
2 3121-00119 Ladder Chord, 12''
3 U-00003 3' [914] Ladder Section
4 U-00004 4' [1 219] Ladder Section
5 U-00005 5' [1 524] Ladder Section
2 7 3121-00170 Inside Ladder Bracket
4 8 U-23779 Locking Clip Assembly
Ladder should be as close
as possible to the Plenum
10 Access Door without
interference, when the
Door is open.
11 Plenum Floor
12 Inside Ladder (position)
13 Plenum Access Door
14 Plumbing side
15 Main Entrance on Base
Module
3 *In SHIP LOOSE Package

12
10
15
13

11

2*
2*
4*

14
3*
Figure 75.
Inside Ladder Location, Top View,
Figure 74. Typical All Models
Inside Ladder Location, Model ME1000S
(3121-00123)

MFH1968-5B 59
Diagrams: Inside Ladders BROCK® MEYER® Walkways and Ladders

ME1200S

6
Item Part No. Description
1 3121-00122 Ladder Chord, 10''
2 3121-00119 Ladder Chord, 12''
4 U-00004 4' [1 219] Ladder Section
6 5 U-00005 5' [1 524] Ladder Section
6 U-00006 6' [1 829] Ladder Section
7 3121-00170 Inside Ladder Bracket
8 U-23779 Locking Clip Assembly
Ladder should be as close
as possible to the Plenum
10 Access Door without
interference, when the
Door is open.
11 Plenum Floor
*In SHIP LOOSE Package

5
10

11

2*
5* 2*

4*

Figure 76.
Inside Ladder Location, Model ME1200S
(3121-00124)
60 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Inside Ladders

ME1400S

6 2

Item Part No. Description

5 1 3121-00122 Ladder Chord, 10''
2 3121-00119 Ladder Chord, 12''
4 U-00004 4' [1 219] Ladder Section
5 U-00005 5' [1 524] Ladder Section
6 U-00006 6' [1 829] Ladder Section
7 3121-00170 Inside Ladder Bracket
5 8 U-23779 Locking Clip Assembly
Ladder should be as close as
possible to the Plenum
10 Access Door without inter-
ference, when the Door is
open.
5 11 Plenum Floor
*In SHIP LOOSE Package

10
5
11

2*
2*
2*
6*

5*

Figure 77.
Inside Ladder Location, Model ME1400S
(3121-00167)
MFH1968-5B 61
Diagrams: Inside Ladders BROCK® MEYER® Walkways and Ladders

ME1600S

5
Item Part No. Description
1 3121-00122 Ladder Chord, 10''
2 3121-00119 Ladder Chord, 12''
4 U-00004 4' [1 219] Ladder Section
5 U-00005 5' [1 524] Ladder Section
6 U-00006 6' [1 829] Ladder Section
7 3121-00170 Inside Ladder Bracket
8 U-23779 Locking Clip Assembly
Ladder should be as close as
5 possible to the Plenum
10 Access Door without inter-
ference, when the Door is
open.
11 Plenum Floor
15 Chord added for Ladder sta-
bility
*In SHIP LOOSE Package

10
5
15
11

2*
2*
2*
6*

5*

Figure 78.
Inside Ladder Location, Model ME1600S
(3121-00126)

62 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Inside Ladders

ME1800S

4
Ladders above dotted line are shipped LOOSE

2
4

Item Part No. Description

1 3121-00122 Ladder Chord, 10''
2 3121-00119 Ladder Chord, 12''
4 U-00004 4' [1 219] Ladder Section
5 U-00005 5' [1 524] Ladder Section
6 U-00006 6' [1 829] Ladder Section
5
7 3121-00170 Inside Ladder Bracket
8 U-23779 Locking Clip Assembly
Ladder should be as close as possi-
10 ble to the Plenum Access Door
without interference, when the
Door is open.
11 Plenum Floor
*In SHIP LOOSE Package

10

11

2*
2*
2*
6* 2*

6*

Figure 79.
Inside Ladder Location, Model ME1800S
(3121-00127)

MFH1968-5B 63
Diagrams: Inside Ladders BROCK® MEYER® Walkways and Ladders

ME2000S

Ladders above dotted line are shipped LOOSE

6
Item Part No. Description
1 3121-00122 Ladder Chord, 10''
6 2 3121-00119 Ladder Chord, 12''
4 U-00004 4' [1 219] Ladder Section
5 U-00005 5' [1 524] Ladder Section
6 U-00006 6' [1 829] Ladder Section
7 3121-00170 Inside Ladder Bracket
8 U-23779 Locking Clip Assembly
6 Ladder should be as close as
10 possible to the Plenum Access
Door without interference,
when the Door is open.
11 Plenum Floor
*In SHIP LOOSE Package

5
10

11

2*
2*
2*
2*
6*

Figure 80.
Inside Ladder Location, Model ME2000S
(3121-00128)

4*

64 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Inside Ladders

ME2400S

Item Part No. Description

1 1 3121-00122 Ladder Chord, 10''
2 3121-00119 Ladder Chord, 12''
3 U-00003 3' [914] Ladder Section
4 U-00004 4' [1 219] Ladder Section
5 U-00005 5' [1 524] Ladder Section
5 6 U-00006 6' [1 829] Ladder Section
7 3121-00170 Inside Ladder Bracket
8 U-23779 Locking Clip Assembly
2 Ladder should be as close as
possible to the Plenum
10 Access Door without inter-
ference, when the Door is
6 open.
11 Plenum Floor
15 Chord added for Ladder sta-
bility
*In SHIP LOOSE Package
6

Ladders above dotted line are shipped LOOSE

11

2*
2*
5
2*
5*
2*
2*

5
5*

5 6*

10
5
Figure 81.
11 Inside Ladder Location, Model ME2400S
(3121-00130)

MFH1968-5B 65
Diagrams: Inside Ladders BROCK® MEYER® Walkways and Ladders

ME2650S

Item Part No. Description

1 1 3121-00122 Ladder Chord, 10''
2 3121-00119 Ladder Chord, 12''
3 U-00003 3' [914] Ladder Section
4 U-00004 4' [1 219] Ladder Section
4 5 U-00005 5' [1 524] Ladder Section
6 U-00006 6' [1 829] Ladder Section
7 3121-00170 Inside Ladder Bracket
2 8 U-23779 Locking Clip Assembly
5 Ladder should be as close as
10 possible to the Plenum Access
Door without interference,
when the Door is open.
11 Plenum Floor
5 15 Chord added for Ladder stabil-
ity
*In SHIP LOOSE Package

5
Ladders above dotted line are shipped LOOSE

10
5
5
11

2*
5 2*
4*
2*
2*
2*
5 5* 2*

5 5*

10
5
11 6*

2*
Figure 82.
4* Inside Ladder Location, Model ME2650S
(3121-00177)

66 MFH1968-5B
BROCK® MEYER® Walkways and Ladders Diagrams: Inside Ladders

MFH1968-5B 67
 TM

Different by Design™
BROCK GRAIN SYSTEMS
A Division of CTB Inc.

Frankfort, Indiana, location:

1750 W. State Road 28 • Frankfort IN 46041
Phone (765) 654-8517 • Fax (765) 654-8510
Toll Free (800) 541-7900
e-mail: [email protected] • Internet: www.graindryers.com

and
P.O. Box 2000 • Milford, Indiana 46542-2000 • U.S.A.
Phone (574) 658-4191 • Fax (574) 658-4133
e-mail: [email protected] • Internet: http//www.ctbworld.com or www.brockgrain.com
and
7400 East Thirteenth Street • Kansas City, Missouri 64126 • U.S.A.
Phone (816) 968-6101 • Fax (816) 968-6272

Printed in the U.S.A.

Changes this issue:

The 5/16'' Hex Head Bolt used for Ladder and Walkway assembly was lengthtened from 3/4'' to 1''.
The ME2000-S with 4 catwalks (3121-00185) was added.
Page 48: Model 3121-00113 now has only three (3) Catwalks.
Page 49: Model 3121-00185 was added: 2000D with four (4) Catwalks.

BROCK GRAIN SYSTEMS reserves the right to change specifications of, or to improve any of its machines,
equipment or attachments thereto at any time without assumption of responsibility to equipment previously
sold.
Thank You: The employees of BROCK GRAIN SYSTEMS would like to thank you for your recent
BROCK® purchase. If a problem should arise, your BROCK dealer can supply the necessary information to
help you.

NOTE: The original, authoritative version of this Manual is the English version produced by CTB, Inc. or any of its subsidiaries
or divisions, (hereafter collectively referred to as "CTB"). Subsequent changes to any Manual made by any third party have not
been reviewed nor authenticated by CTB. Such changes may include, but are not limited to, translation into languages other than
English, and additions to or deletions from the original content. CTB disclaims responsibility for any and all damages, injuries,
Warranty claims and/or any other claims associated with such changes, inasmuch as such changes result in content that is differ-
ent from the authoritative CTB-published English version of the Manual. For current product installation and operation infor-
mation, please contact the Customer Service and/or Technical Service Departments of the appropriate CTB subsidiary or
division. Should you observe any questionable content in any Manual, please notify CTB immediately in writing to: CTB Legal

May 2014 MFH1968-5B