HCD-XB3K

SERVICE MANUAL E Model

et
HCD-XB3K is the tuner, deck, CD and

.n
amplifier section in LBT-XB3K.

Model Name Using Similar Mechanism HCD-XB3

CD CD Mechanism Type CDM37L-5BD29AL
nd Section Base Unit Name
Optical Pick-up Name
BU-5BD29AL
KSS-213D/Q-NP
Tape deck Model Name Using Similar Mechanism HCD-XB3
Section Tape Transport Mechanism Type TCM-220WR2

SPECIFICATIONS
ou

Amplifier section CD player section

Continuous RMS power output 70 + 70 watts System compact disc and digital audio system
(6 ohms at 1 kHz, 10% THD) Laser Semiconductor laser (λ = 780 nm).
Peak music power output 1000 watts Emission
Inputs duration: continuous
PHONO IN (phono jack): sensitivity 3 mV, impedance 47 kilohms Laser output Max. 44.6µF*
VIDEO (AUDIO) IN (phono jack):sensitivity 250 mV, impedance 47 *This output is the value measured at a distance
kS

kilohms of 200 mm from the objective lens surface on the

MIX MIC (phono jack): sensitivity 1 mV, impedance 10 kilohms Optical Pick-up Block with 7 mm aperture.
Outputs Wavelength 780 –790 nm
PHONES (stereo phone jack): accepts headphones of 8 ohms or more Frequency response 2 Hz – 20 kHz (± 0.5 dB)
SPEAKER: accepts impeadance of 6 to 16 ohms. Signal-to-noise ratio More than 90 dB
Dynamic range More than 90 dB

Tape player section

Le

Recording system 4-track 2-channel stereo

Frequency response (DOLBY NR OFF)
60 – 13,000 Hz (± 3 dB), using a Sony
TYPE I cassette
60 – 14,000 Hz (± 3 dB), using a Sony
TYPE II cassette

– Continued on next page –

COMPACT DISC DECK RECEIVER

MICROFILM
 SECTION 3
TEST MODE
[MC Cold Reset] [Change-over of AM Tuner Step between 9kHz and 10kHz]
• The cold reset clears all data including preset data stored in the • A step of AM channels can be changed over between 9kHz and
RAM to initial conditions. Execute this mode when returning 10kHz.
the set to the customer. Procedure:
Procedure: 1. Press POWER button to turn the set ON.
1. Press three buttons GROOVE , ENTER/NEXT , and 2. Select the function “TUNER”, and press TUNER/BAND
DISC 1 simultaneously. button to select the BAND “AM”.
2. The fluorescent indicator tube becomes blank instantaneously, 3. Press POWER button to turn the set OFF.
and the set is reset. 4. Press ENTER/NEXT and POWER buttons simultaneously,
and the display of fluorescent indicator tube changes to “AM
[CD Delivery Mode] 9k STEP” or “AM 10k STEP”, and thus the channel step is
• This mode moves the pick-up to the position durable to vibra- changed over.
tion. Use this mode when returning the set to the customer after
repair. [LED and Fluorescent Indicator Tube All Lit, Key Check
Procedure: Mode]

et
1. Press POWER button to turn the set ON. Procedure:
2. Press PLAY MODE button and POWER button simulta- 1. Press three buttons GROOVE , ENTER/NEXT , and DISC 3
neously. simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator 2. LEDs and fluorescent indicator tube are all turned on.
tube, and the CD delivery mode is set. Press DISC 2 button, and the key check mode is activated.

.n
3. In the key check mode, the fluorescent indicator tube displays
[MC Hot Reset] “K 1 V0 J0”. Each time a button is pressed, “K”value in-
• This mode resets the set with the preset data kept stored in the creases. However, once a button is pressed, it is no longer taken
memory. The hot reset mode functions same as if the power into account.
cord is plugged in and out. “J” value increases like 1, 2, 3 ... if rotating JOG knob in “+”
Procedure: direction, or it decreases like 0, 9, 8 ... if rotating in “–” direc-
1. Press three buttons GROOVE , ENTER/NEXT , and
DISC 2 simultaneously.
nd tion.
“V” value increases like 1, 2, 3 ... if rotating VOLUME knob
2. The fluorescent indicator tube becomes blank instantaneously, in “+” derection, or it decreases like 0, 9, 8 ... if rotating in “–
and the set is reset. ” direction.
4. To exit from this mode, press three buttons in the same man-
[Sled Servo Mode] ner as step 1, or disconnect the power cord.
• This mode can run the CD sled motor freely. Use this mode, for
ou
instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons GROOVE , ENTER/NEXT , and
FLASH simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
kS

4. With the CD in stop status, press ) button in CD section

to move the pick-up to outside track, or 0 button to inside
track.
5. To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pick-up to most inside track when exiting from
Le

this mode. Otherwise, a disc will not be unloaded.

• Do not run the sled motor excessively, otherwise the gear can
be chipped.

– 30 –
[Aging Mode] 8. To exit from the aging mode, press POWER button to turn
This mode can be used for operation check of CD section and tape the set OFF.
deck section.
• If an error occurred: 2-2. Operation during Aging Mode
The aging operation stops. In the aging mode, the program is executed in the following se-
• If no error occurs: quence.
The aging operation continues repeatedly. 1. A tape on FWD side is played for one minute.
2. PAUSE STOP is made.
1. Aging Mode in CD Section 3. Recording is made for 3 minutes. (For the deck not having
1-1. Operating Method of Aging Mode the record function, the play is executed.)
1. Set discs in DISC 1 and DISC 3 trays. 4. FF is executed up to the end of tape.
2. Select the function “CD”. 5. A tape is reversed, and the tape on REV side is played for
3. Press three buttons GROOVE , ENTER/NEXT , and one minute.
DISC 5 simultaneously. 6. PAUSE STOP is made.
4. The aging mode is activated, if a roulette mark on the fluo- 7. Recording is made for 3 minutes. (For the deck not hav-

et
rescent indicator tube is blinking. ing the record function, the play is executed.)
5. In the aging mode, the aging is executed in a sequence 8. FF is executed up to the end of tape.
given in “1-2. Operation during Aging Mode”. 9. Steps 1 through 8 are executed for the other deck.
The aging continues unless an alarm occurred. 10. Steps 1 through 9 are repeated unless an alarm occurred.
6. To exit from the aging mode, press POWER button to turn
2-3. Deck Selection Sequence

.n
the set OFF.
• If a button other than buttons In CD section is pressed during • During the aging mode, decks are selected in the following se-
aging, the aging in the CD section is finished. quence:
• To execute aging to the tape deck section successively, press · Deck A (FWD) → Deck A (REV)
button in the deck A. ↑ ↓
“AGING” is displayed on the fluorescent indicator tube. (For Deck B (REV) ← Deck B (FWD)
nd
the aging in tape deck, see “2. Aging Mode in Tape Deck Sec-
tion”.

1-2. Operation during aging Mode

In the aging mode, the program is executed in the following se-
quence.
1. The disc tray turns to select a disc. (For a disc selection
ou
sequence, see Section 1-3.)
2. TOC of disc is read.
3. The pick-up accesses to the last track.
4. Steps 1 through 3 are repeated.

1-3. Disc Selection Sequence

• During the aging mode, discs are selected in the following se-
kS

quence:
Disc 1 → Disc 3
↑ ↓
Disc 3 ← Disc 1

2. Aging Mode in Tape Deck Section

2-1. Operating Method of Aging Mode
1. Load a commercially available 10-minute tape into the
Le

decks A and B respectively.

(If a 10-minute tape is not available, another tape may be
used but a cycle time will be longer.)
2. Select the function “TAPE”.
3. Rewind tapes in advance by pressing 0 button respec-
tively on decks A and B.
4. Press three buttons GROOVE , ENTER/NEXT , and
DISC 5 simultaneously.
5. Press · button on deck A. (This button triggers the ag-
ing mode.)
6. The aging mode is activated if “AGING A” is displayed on
the fluorescent indicator tube.
7. In the aging mode, the aging is executed in a sequence
given in “2-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.

– 31 –
 SECTION 4 SECTION 5
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
PRECAUTION
DECK SECTION 0dB=0.775V
1. Clean the following parts with a denatured-alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head demagne-
record/playback head pinch roller tizer. (Do not bring the head demagnetizer close to the erase
erase head rubber belts head.)
capstan idlers 2. Do not use a magnetized screwdriver for the adjustments.
2. Demagnetize the record/playback head with a head demagne- 3. After the adjustments, apply suitable locking compound to the
tizer. parts adjust.
3. Do not use a magnetized screwdriver for the adjustments. 4. The adjustments should be performed with the rated power
4. After the adjustments, apply suitable locking compound to the supply voltage unless otherwise noted.
parts adjusted. 5. The adjustments should be performed in the order given in
5. The adjustments should be performed with the rated power this service manual. (As a general rule, playback circuit ad-
supply voltage unless otherwise noted. justment should be completed before performing recording
• Torque Measurement circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-

et
Mode Torque Meter Meter Reading ch.
36 to 61g•cm 7. Switches and controls should be set as follows unless other-
Forward CQ-102C
(0.50 – 0.84 oz•inch) wise specified.
Forward 2 to 6g•cm 8. Set to test mode. (Press key switch same time GROOVE
CQ-102C ENTER/NEXT and DISC 4 button.)
Back Tension (0.026 – 0.082 oz•inch)

.n
36 to 61g•cm • Test Tape
Reverse CQ-102RC
(0.50 – 0.84 oz•inch)
Reverse 2 to 6g•cm Tape Signal Used for
CQ-102RC
Back Tension (0.026 – 0.082 oz•inch) P-4-A100 10kHz, –10 dB Azimuth Adjustment

FF, REW CQ-201B

61 to 143g•cm
nd
(0.85 – 1.98 oz•inch)
WS-48B
P-4-L300
3kHz, 0dB
315Hz 0dB
Tape Speed Adjustment
Level Adjustment
• Tape Tension Measurement
Record/Playback Head Azimuth Adjustment
Mode Tension Meter Meter Reading
Forward CQ-403A more than 100g (3.52 oz) DECK A DECK B
Reverse CQ-403R more than 100g (3.52 oz) Note: Perform this adjustments for both decks
ou
Procedure:
1. Mode: Playback (FWD)
test tape main board
P-4-A100 CN207
(10 kHz, –10 dB) Pin 1 (L-CH)
Pin 3 (R-CH) level meter

set
kS

+
–
main board
CN207
Pin 2
Le

– 32 –
1. Mode: Playback (FWD) Tape Speed Adjustment DECK A
2. Turn the adjustment screw and check output peaks. If the peaks Note: Start the Tape Speed adjustment as below after setting to
do not match for L-CH and R-CH, turn the adjustment screw the test mode.
so that outputs match within 1dB of peak. In the test mode, the tape speed is high during pressing the
H. SPEED DUBB button.
Procedure:
1. Turn the power switch on.
within 2. Press the SPECTRUM ANALYZER button, ENTER button
L-CH 1dB
peak and EFFECT button simultaneously.
within To exit from the test mode, press the POWER button.
output 1dB
level Mode: Playback (FWD)
test tape
R-CH WS-48B frequency counter
peak (3 kHz, 0 dB)
Screw Screw

et
position L-CH R-CH position +
peak peak set
–
3. Mode: Playback (FWD) MAIN board
CN207 (Pin 1 : L-CH)
test tape (Pin 3 :R-CH)
P-4-A100

.n
(10kHz, –10dB) oscilloscope
pin 1 1. Insert the WS-48B into the deck A and the blank tape into the
L-CH
deck B.
pin 2
MAIN L 2. Press the REC button and · button on the deck B. Then
board V H
the deck B is at recording mode.
CN207
set R 3. Set the deck A to playback mode.
R-CH
pin 3
nd 4. Keep pressing the H. SPEED DUBB button in playback mode.
Then at HIGH speed mode.
5. Adjust RV652 on the AUDIO board do that frequency counter
reads 6,000 ± 90 Hz.
waveform of oscilloscope
6. Take off the H. SPEED DUBB button.
Then at NORMAL speed mode.
7. Adjust RV651 on the AUDIO board so that frequency counter
in phase 45° 90° 135° 180°
reads 3,000 ± 90 Hz.
ou
good wrong 8. Frequency difference between deck A and deck B the begin-
ning of the tape should be within ± 1.5%.
4. Repeat steps 1 to 3 in playback (REV) mode. Adjustment Location: AUDIO board
5. After the adjustments, apply suitable locking compound to the
pats adjusted. Sample Value of Wow and flutter: 0.3% or less W.RMS (WS-48B)
Adjustment Location: Record/Playback Head (Deck A and B)
Playback level Adjustment DECK A DECK B
kS

and MAIN board.

Procedure:
Mode: Playback (FWD)
test tape
P-4-L300 level meter
(315 Hz, 0 dB)

set +
–
Le

reverse MAIN board

CN207 (Pin 1 : L-CH)
(Pin 3 : R-CH)
Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301 (L-
CH) and RV401 (R-CH) so that adjustment within adjustment level
as follows.
Adjustment Level:
CN207 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
difference between the channels: within ±0.5 dB
forward Adjustment Location: AUDIO and MAIN boards

– 33 –
Record bias Current Adjustment DECK B Adjustment Location:
Procedure: [MAIN BOARD] (Component Side)
1. Mode: Record
RV1501
Pin 6 (L-CH) of IC1501 on the MAIN board.
Pin #¶ (R-CH) of IC1501 on the MAIN board. 1 IC1501
3
1) 315 Hz  CN207 CN205
2) 10 kHz  50 mV (–23.8 dB) IC301
 IC201 RV1551
AF OSC blank tape
600 Ω CN-123 Record Level
attenuator Adjustment
set

Pin 2 (GND) of ICN207 on the MAIN board.

et
2. Mode: Playback
recorded level meter
portion [AUDIO BOARD] (Conductor Side)

+ Record Bias Current

set Tape Speed Adjustment
Adjustment

.n
–


















R L (NORMAL) (HIGH)
CN207 (Pin 1 : L-CH) RV301®L
(Pin 3 : R-CH) RV651 RV652
RV401®R RV441 RV341
® ®




 
Confirm playback the signal recorded in step 1 become adjustable  RV311
Playback Level
limits as follows. Adjustment
Playback Level  L ®
nd
If these levels do not adjustable limits, adjustment the RV341 (L-
CH) and RV441 (R-CH) on the AUDIO board to repeat steps 1 and
– DECK B –
Adjustment

 RV411
R®
2. – DECK A –
Adjustable limits: Playback output of 315 Hz to playback output
of 10kHz: 0±0.5 dB
Adjustment Location: AUDIO and MAIN boards
ou

Record Level Adjustment DECK B

Pin 6 (L-CH) of IC1501 on the MAIN board.

Pin #¶ (R-CH) of IC1501 on the MAIN board.
315 Hz, 50 mV (–23.8 dB)
AF OSC
blank tape
kS

600 Ω CS-123
attenuator
set

Pin 2 (GND) of CN207 on the MAIN board.

Procedure:
Le

recorded level meter

portion

set +
–

CN207 (Pin 1 : L-CH)

(Pin 3 : R-CH)
1. Mode: Record
2. Mode: Playback
Confirm playback the signal recorded in step 1 become adjustable
limits as follows.
If these levels do not adjustable limits, adjustment the RV1501
(L-CH) and RV1551 (R-CH) on the MAIN board to repeat steps 1
and 2.
Adjustable limits:
CN207 PB level: 47.3 to 53.1 mV (–24.3 to –23.3 dB)
Adjustment Location: MAIN board

– 34 –
 TUNER SECTION 0dB=1µV

Note: As a front-end (FE1) is difficult to repair if faulty, replace

it with new one.

AM Section Adjustment
Setting:

loop antenna
loop antenna (Supplied accessories)

AM RF SSG

et
set

30% amplitude
modulation by
400 Hz signal 60 cm AM ANTENNA
terminal (TM1)
Field strength dB (µV/m) =SSG output level dB (µV/m) –26 dB.

.n
AM Tuned Level Adjustment
Band: AM
Procedure:
Adjustment Location:
1. Set the output of SSG so that the input level of the set be-
comes 55 dB. [TCB BOARD] (Component Side)
2. Tune the set to 999 kHz.

tor will change from going off to going on.

nd
3. Adjust RV42 to the point (moment) when the TUNED indica- IC2
RV42
AM Tuned
RV41 Level
Adjustment Location : TCB board FM Tuned Level Adjustment
Adjustment
FM Section Adjustment
Note: This adjustment should be performed after the AM Tuned
ou

Level Adjustment due to the same adjustment element. TM1

Setting:

FM RF stereo signal FE1

generator
75 Ω coaxial
kS

set
Carrier frequency : 98 MHz
Modulation : AUDIO 1 kH, 75 kHz
deviation (100%) FM ANTENNA terminal
(TM1) (75 Ω open)
Le

FM Tuned Level Adjustment

Band: FM
Procedure:
1. Supply a 25dBµ 98 MHz signal from the ANTENNA termi-
nal.
2. Tune the set to 98 MHz.
3. If the TUNED indicator does not light, adjust RV41 to the
point (moment) when the TUNED indicator will change from
going off to going on.
Adjustment Location: TCB board

– 35 –
 CD SECTION S Curve Check
Note: oscilloscope
1. CD Block is basically designed to operate without adjustment. BD board
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (FEO) +
3. Use an oscilloscope with more than 10M impedance. TP (VC) –
4. Clean the object lens by an applicator with neutral detergent
Procedure:
when the signal level is low than specified value with the fol-
1. Connect oscilloscope to test point TP (FEO).
lowing checks.
2. Connect between test point TP (FOK) and GND by lead wire.
3. Turn Power switch on.
Focus Bias check
oscilloscope 4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc
BD board table is moving in and out.)
TP (FEO) + 5. Check the oscilloscope waveform (S-curve) is symmetrical

et
TP (VC) – between A and B. And confirm peak to peak level within 3±1
Vp-p.
Procedure: S-curve waveform
symmetry
1. Connect oscilloscope to test point TP (RF). (GND terminal :
VC)

.n
2. Turned Power switch on. A
3. Put disc (YEDS-18) in and playback. within 3 ± 1 Vp-p
4. Confirm that the shape “≈” can be clearly distinguished at the B
center of the waveform and check the RF signal level.

• RF signal 6. After check, remove the lead wire connected in step 2.

nd
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
Note: • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
level:
1.3 ± 0.3 Vp-p
RF Level Check
oscilloscope
ou

BD board

TP (RF) +
TP (VC) –

Procedure:
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
kS

3. Put disc (YEDS-18) in and playback.

4. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
Le

level:
1.3 ± 0.3 Vp-p

Note:
Clear RF signal waveform means that the shape “≈” can be
clearly distinguished at the center of the waveform.

– 36 –
E-F Balance (1 Track Jump) check Adjustment Location:
(Without remote commander)
[BD BOARD] (Conductor Side)
oscilloscope
BD board
RF
TP (TEO) + VC
TP (VC) – FOK

CNU101
Procedure: IC
IC101
1. Connect oscilloscope to test point TP (TEO) on BD board. I02
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
TEO
4. Press the “P (Pause)” button. (Becomes the 1 track jump
mode) FEO
GND
5. Check the level B of the oscilloscope's waveform and the A

et
(DC voltage) of the center of the Traverse waveform.
Confirm the following:
IC103
A–B × 100 = ±7 (%)
2 (A + B)

.n
1 track jump waveform
Center of the waveform

B CNU102

A (DC voltage)
0V
nd
symmetry
level : 500 mV ± 100 mVp-p
ou
kS
Le

– 37 –
 SECTION 6
DIAGRAMS
• Circuit Board Location

TRANS board

PANEL board TCB board

KEY CON board

et
MAIN board

HEADPHONE-MIC
board

.n
TC-A SW
board
POWERAMP
board

LED board
nd
CD-A SW board TC-B SW board

CD-B1 SW board
DOOR SW board
ou

CD-B2 SW board

MOTOR board
kS

LEAF SWITCH
board
Le

CD MOTOR board

BD board

AUDIO board

TABLE SENSOR board BD LED board

– 38 –
• Waveforms
— BD Section—
1 IC101 #£ pin (PLAY MODE) 6 IC103 ^™ pin (RFCK) !¡ IC301 !£ pin (XT2)

Approx. 1.3 Vp-p

4.6 Vp-p

31.3 µsec

et
2 IC101 2 pin (FEI) (PLAY MODE) 7 IC103 &¢ pin (WFCK) — TUNER Section—
!™ IC1 @¢ pin (XOUT)

.n
Approx. 0.1 V 5.6 V
4.8 Vp-p

nd 135.5 µsec
3 IC101 $¶ pin (TEI) (PLAY MODE) 8 IC103 *ª pin (XTAI) 222 nsec
!£ IC2 @£ pin (VCO)
ou
Approx. 0.2 V 10 V

4.8 Vp-p

59.8 nsec
kS

4 IC103 @¶ pin (MDP) — PANEL Section—

9 IC601 8 pin (X-OUT) 2.2 nsec

2.4 V

2.1 V
Le

7.8 µsec
5 IC103 ^º pin (XPCK) 125 nsec
— MAIN Section—
0 IC301 0 pin (X2)

7V

5.7 V

230 nsec

200 nsec

– 39 –
HCD-XB3K

6-1. BLOCK DIAGRAMS

– TUNER SECTION –

ST +10V

Q5 22 MPX IN AMP OUT L 16

TM1 FE1 AM / FM 24
ANTENNA FM FRONT END CF1 CF2
10.7MHz OUT L 20 LPF 18 AMP IN L
IF AMP IF AMP 10.7MHz
FM 75Ω ANT IN IF OUT 1 FM IN
Q1,2 Q3,4
F OUT

OUT R 21 RCH
VT

A
AM MAIN SECTION
(page 43)
IC2

et
FM / AM MPX

STEREO 70
4 REG ST LED 8
TUNED 69
TUNED 7

AM MIX 2 AM IF 5 AM IF
IFT41

.n
AM
FE2 SD 12
AM FRONTEND
7 RV42
B+ AM
TUNED
F OUT 9 29 AM OSC LEVEL
3 ANT IN
9 DET
X42
nd
RF OUT 13 27 AM RF IN
FM SD

AM / FM
VCO STOP
IF BUFF
MUTE AM 13
SD
X43
10.7MHz

450KHz
VT 23 VCO
14 X41
30 14 15 11
456KHz
ou

RV41
FM
TUNED MUTE 72
LEVEL B
MAIN
kS

SECTION
(page 44)
Le

X21
4.5MHz

10 15 19 14 7 2 12 8 1 24
ST-CE 68
X OUT
FM

X IN
PD1
FM OSC

VCO STOP
AM OSC

IF REQ
FM

IF

CE 3
COM-DIN 67
DI 4
PLL
IC1 COM-CLK 65
CL 5
COM-DATA 66
DO 6

• R CH:Same as L CH
• SIGNAL PATH
:FM

:AM

– 40 –
 HCD-XB3K

t
– CD SECTION – – DECK SECTION –

ne
RV311 MAIN
IC611 REC REC
PB LEVEL 6 F SECTION
PBEQ 70 (page 43)
DOL
3 1 2 DOLBY PB
AMP MAIN
HP101 B 8 G
PB SECTION
PLAYBACK HEAD (page 43)
OPTICAL PICK-UP BLOCK 120 PAS
X101 (A DECK) R-CH IC601 4
IC101(1/2) 16.9344MHz
PBEQ RV301
FOCUS/TRACKING 5 7
B+ AMP PB LEVEL
DETECTOR K /SLED/SERVO IC602
RF AMP PB / REC SW
89 90 HRPE101
E RV105 9
1
1 38 PD1 RFO 33 44 RF REC LEVEL
A 35 PB R-CH
4 MAIN REC/PB HEAD
C,OUT 24 14 CNIN LOUT1 86 E SECTION (B DECK) 2 10 IC1501
2 39 PD2 4
A D SENS1 25 13 SEIN (page 43) R-CH HEAD AMP 37 REC R-CH
D IC103
5 DECK PROCES
FOK 27 23 FOK DIGITAL SIGNAL
B C 10 41 F PROCESSOR R-CH 3
C DATA 22 15 DATAO C331,L331
ERASE RV341

d.
6 42 E X
XLT 21 16 XLTO (HEAD) REC BIAS BIAS REC
LOUT2 93 R-CH 11
B CLK 20 17 CLKO TRAP EQ
LOCK 19 29 LOCK Q621,622

NORM/CROM/METAL
F BIAS OSC

CLOCK
FE-O 6 T621

SPOD

SCOR

SQCK
XRST

SENS
SQS0
DATA
XLAT
MDP
NORM
25

REC/PB/PASS
FE-M 7 Q623 BIAS

BIAS ON/OFF
NORM/HIGH

RM ON/OFF

LM ON/OFF
NR ON/OFF
21 27 75 100 12 11 10 9 8 7 SWITCH 24 SW

A120/170
CROM

PB A/B
TA-M 12

57

47
74
18

48
58

34
36
TA-O 13 S101 +7V 22
LIMIT SWITCH
12 13 14 15 16 17 18 19 20
Q101 36 LD S1005
LD DRIVE 73 MAIN
XRST SENS2 26 C SECTION A CrO2
37 PD (page 43)
LASER S1008
DIODE B CrO2

96
23

un

87

88

89
90
91
92
93
Q1531,Q1532 MAIN
H
CAPSTAN MOTOR SECTION
FOCUS TRACKING 9 (page 43)
COIL COIL SWITCH 86
MUTE
T- RV652
15 TRACKING M1 B+
COIL DRIVE 27 HIGH SPEED
16 CAPSTAN M (+12V)
MOTOR Q651
Q1533
FOCUS / TRAKING CAPSTAN MOTOR
T+ SWITCH 82
COIL DRIVE RV651 CONTROL
IC102 (1 / 2 ) NORMAL SPEED
2-AXIS
DEVICE Q1534,Q1535
F- IC1502 85
18 FOCUS 2 4 SWITCH
26 M2 TRIGGER
F+ COIL DRIVE
17 TRIGGER M MOTOR 5 83
MOTOR 10 DRIVE 61
84
S1001
A PLAY
SLED / SPINDLE 94
MOTOR DRIVE SLED
IC102 (2 / 2) SERVO S1002 95
IC101 (2 / 2)
B PLAY
SoM102
M 12
. SLED MOTOR 6 16 SLO SL-P 14
S1004
(A HALF) 97
SLED MOTOR 11 DRIVE
S1007
(B HALF)
M101 14 28
SPINDLE MOTOR M .
13
SPINDLE MOTOR 3
S1006
DRIVE MAIN
(REC A) +5V I
SECTION
S1009 (page 43) • R CH : Same as L CH
(REC B) • SIGNAL PATH
77 :PB (DECK A)
S201 MAIN
UP SWITCH D SECTION
:PB (DECK B)
(page 43)
:REC (DECK B)
IC202 76
DISC TABLE
SENSOR

Q201 62
SWITCH • R CH:Same as L CH
• SIGNAL PATH
61
ek

3 IC201 1 :CD
M201
TABLE MOTOR
M 7
MOTOR
9
60
DRIVE

– 41 – – 42 –
HCD-XB3K

t
– MAIN SECTION –
IC231
SPEANA MIX R-CH

ne
J760
2
+ PHONES
J101 (1 / 2) IC101 – 1
PHONO 3
PHONO AMP
IC801
DECK SECTION 65 64 POWER AMP
G 15 69
(page 42)
+ RY141
CD SECTION E 14 13 71 45 44 43 42 38 1 +
(page 41) – 10 + L-CH
A 2 – Q801
28 R-CH
TUNER SECTION A 11 B MICON EQ Q204 OVER LOAD
(page 40) 29 - TM131
C INTERFACE MUTE R-CH 17 + DET
J101 (2 / 2) 12 3 R-CH 30 IC201 13 R-CH SPEAKER

BB22

BB12
EQUALIZER/VOLUME 18 –
VIDEO (AUDIO) MUTE Q851 -
A
4 10 6 OVER LOAD
B 32 33 34 62 40 41 Q231
R-CH 5 9 DET + R-CH
SWITCH R-CH
2 C
6
Q283
IC102 INPUT SELECTOR Q232 MUTE Q282
Q202 Q203 Q141,Q142
SWITCH OVER LOAD
DBFB SWITCH FEED BACK RELAY DRIVE

d.
DECK SECTION DET
(page 42) F

45
44

2
3
2 1 4
Q281 IC281
7
SWITCH PROTECTOR
IC502
6
MULTIPLEXER

5 4

22 LPF1 IN MPX OUT 15 3

44 44
45 45
3
2
20 HPF IN 14 R-CH
STORE BE 9

4
5
9

87
88
89
90
91
92
93
96

55
56
+5V 14 VCC DATA 7 CD SECTION

un
C TUNER B
Q502 (page 41)
IC501 SWITCH SECTION

18
34
36
47
48
57
58

73
74
KEY CONTRTOL (page 40)

65
66
67
68
69
70
72
Q501
SWITCH 18 34 36 47 48 57 58 73 74 2 87 88 89 90 91 92 93 96 3 44 45 4 5 65 66 67 68 69 70 72 55 56 100 6 1

SCOR
SQ-DATA-IN
SQCLK
CD DATA
CD CLOCK
XRST
XLT

SENS2
SENS

DBFB H/L

PB A/B
EQ-H/N
BIAS
REC-MUTE
NR ON/OFF
R/P-PASS
TC-MUTE
REALY

427LAT

COM DOUT
COM CLK

A-SHUT KEY-CON LAT

KEY-CON ON

ST-CLK
ST-DIN
ST-DOUT
ST-CE
TUNED
STEREO
ST MUTE

11C-DATA
11C-CLK

STK MUTE

F-RELAY

TA MUTE
45

44
4

IC301

CD-POWER
RV761

CAP-M-ON/OFF
MAIN CONTROL

B-SHUT

POWER

AC CUT
IC761 ECHO LEVEL

A HALF

B HALF

RESET
A-PLAY-SW
B-PLAY-SW
TRAY-LED

TRG-LOW
J762

XT2

XT1
CAP-H/N

X2

X1
T-SENS
MIC2

UP SW
1 8

B-TRG
A-TRG
TBL-R
TBL-L
97 28 26 27 46 10 11 13 14 98 15 20
KEY CONTROL
77 76 62 61 60 86 85 84 83 82 94 95
IC760 (1 / 2) RV706 IC760 (2 / 2) X301 X302

77
76

62
61
60
Q301
MIC AMP MIC LEVEL MIC AMP 5MHz 32.768KHz
SWITCH
J761 CD SECTION D Q1001 Q1002
Q901 Q901
MIC1 (page 41) REEL REEL
Q902 Q902
DET DET
SWITCH SWITCH

86
85
84
83
82

94
95

97

28
DECK SECTION I IC302
(page 42) Q907 Q905 RESET
So SWITCH Q906
SWITCH
H +5V
55
56

DECK SECTION
(page 42)
LED DRIVE +35V D901
VOLUME
-35V RECT
Q604-Q608 S691
D611-D625 Q609-Q612 S601-S626,S628-S633 JOG DOOR SW ROTARY
D627 Q614 S641-S647,S651-S659 S711 ENCODER
D631,D632 S661-S668,S676-S679 +7V IC901 T901
Q617-Q619 S701
-7V REG POWER TRANSFORMER
D635-D638 Q621 AC -IN
D641 D902
D645-D647 IC902 |
79-80 • 1-6 • 14-19 27 - 30 22 • 35 21 20 34 CD MOTOR +7V
REG D905
LED KEY1-KEY4 JOG A•B
DOOR SW

SELECT SWITCH RECT

25 LED SELECT +5V IC903
Q601-Q603 IC601 REG
DISPLAY CONTROL
23 CLOCK D906 S901 • R CH:Same as L CH
Q903 IC904
SPEANA1
SPEANA2

ST +10V D907 VOLTAGE

24 DATA REG REG • SIGNAL PATH
RESET
SIRCS
X OUT

RECT SELECTOR
ek
X IN

L+R

TC MOTOR
GR1-GR15 SEG1-SEG20 :FM
+12V EXCEPT MY
42- 56 57- 77 8 9 32 36 37 33 10 VP Q904
REG :PB (DECK A)
IC602 VF :PB (DECK B)
SIRCS
BACK LIGHT :REC (DECK B)
FL601 X601
VF MID FREQ
VF 8MHz :CD
FRUORESCENT INDICATOR TUBE
-7V +7V LOW FREQ
• Abbreviation
D671-D674 HIGH FREQ
MY :Malaysian model

– 43 – – 44 –
ek
So
un
d.
ne
t
ek
So
un
d.
ne
t
ek
So
un
d.
ne
t
ek
So
un
d.
ne
t
ek
So
un
d.
ne
t
ek
So
un
d.
ne
t
ek
So
un
d.
ne
t
ek
So
un
d.
ne
t
ou
nd.
So
un
d.
n
ek
So
un
d.
ne
t
So
un
d.
n
So
un
d.
n
• IC Block Diagram – MAIN Section –
IC201 M62427FP

VOL OUT2
KEY OUT2

VOL IN2
REC 2A

REC 2B

REC 2C

F OUT2
F1 IN2

F2 IN2

F3 IN2

F4 IN2

BBIN2
F1 O2

F2 O2

F3 O2

F4 O2
F1 F2

F2 F2

F3 F2

F4 F2

F5 F2

BB12
NC7

NC6
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

KEY IN2 65 SBAND GRAPHIC EQUALIZER 40 BB22

–
BPF OUT 66 + 39 BUF IN1
+
–
BPF IN 67 38 BUF OUT1

NC8 68 37 NC5

–
+
IN 2B 69 + 36 AVDD
+ +
–
NC9 70 – – 35 DGND

et
IN 2A 71 – 34 LATCH
U-CON
+
AVSS 72 – – INTER 33 DATA
+ + FACE
AGND 73 32 CLOCK

IN 1A 74 31 DVDD

.n
NC1 75 – – 30 PORT C
+ +
+
IN 1B 76 – 29 PORT B

+
–
NC2 77 28 PORT A

DELAY IN 78 – 27 BUFOUT1
+
DELAY OUT 79

KEY IN1 80
–
nd
SBAND GRAPHIC EQUALIZER
+
26 BUFIN1

25 BB21

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
REC 1A

REC 1C
KEY OUT1

NC3

REC 1B

NC4

F1 F1

F1 O1

F2 F1

F2 O1

F2 IN1

F3 F1

F3 O1

F3 IN1

F4 F1

F4 O1

F4 IN1

F5 F1

F OUT1

VOL IN1

VOL OUT1

BBIN1
F1 IN1

BB11
ou
kS

IC281 µPC1237HA

OVER LOAD DET

VCC ON
F/F MUTE
OFFSET DET
Le

LATCH/
AUTORESET

AC OFF
DET

VCC
1 2 3 4 5 6 7 8

– 78 –
ek
So
un
d.
ne
t
ek
Sou
nd.
n et
 t
• IC Block Diagram IC102 BA5941FP
IC101 CXA1992AR

ne OP OUT

OP IN (–)

OP IN (+)

OUT3A

OUT3B

OUT4A

OUT4B
IN4B

IN4A

IN3B

IN3A

GND

VCC
RF_M

RF_O
RFTC

NC
RF_I
PD2

PD1

CC1

CC2

FOK
PD

LD

CP

CB
39 38 37 36 35 34 33 32 31 30 29 28 27 28 27 26 25 24 23 22 21 20 19 18 17 16 15
VEE NC
– +
–
+ Vcc + – + –

–
+

–
+

–
+
+ – + –
RF SUMMING
PD2 IV PD1 IV

–
+
AMP
AMP AMP

–
+
+
–
FE_BIAS 40 26 SENS2

–
+
VCC +

+
–
APC – –
LEVEL SHIFT
IIL
+
VEE
F 41 – ↓ 25 SENS1 –
+ LASER POWER CONTROL
TTL LEVEL SHIFT
F IV AMP VCC +

–
+

+
–
+
VCC VCC

d.
FE AMP
E 42 – 24 C. OUT +

–
+

–
+
+ LEVEL SHIFT
–
E IV AMP
VEE +

–
+

+
LEVEL SHIFT
–
DFCT –

–
+
EI 43 23 XRST

–
+
IFB4
IFB5
IFB2
IFB3

IFB6
IFB1
BAL1
BAL2
BAL3
BAL4

+
VEE

–
+
–
LEVEL S
VEE
TGFL

VEE
VEE 44 VEE 22 DATA
TOG4
TOG3
TOG2
TOG1

FO. BIAS

–
–

+
+
WINDOW VCC – + + – – + + –
–
+

MIRR IIL
COMP. Vcc MUTE Vcc
+ ↓

–
+
– TTL TTL
TEO 45 + TRK. GAIN FOK ↓ 21 XLT
– WINDOW COMP. IIL
+ + 1 2 3 4 5 6 7 8 9 10 11 12 13 14
– –

VCC

BIAS IN

IN1B

IN1A

IN2B

IN2A

GND

GND

MUTE

VCC

OUT2A

OUT2B

OUT1A

OUT1B
DFCT1
E-F BALANCE LDON

MIRR
LPCL

TGFL

un
LPC

CC1
LPFI 46 + WINDOW COMP. 20 CLK
+
– FOH
–
FOL
TGH
TGL IIL DATA REGISTER
TEI 47 19 LOCK
BALH INPUT SHIFT REGISTER
– ADDRESS DECODER
+ BALL
SENS SELECTOR
ATSC
OUTPUT DECODER
TZC
ATSC 48 – FZC VCC 18 VCC IC103 CXD2519Q
+
ATSC

PCMDI
EMPHI

PCMD
LRCKI
SYSM

EMPH
WFCK

MNT0
MNT1
MNT3
SCOR

DOUT
SBSO

GTOP
XROF
C2PO

XPCK
XUGF
EXCK

RFCK
WINDOW

XTSL
FSTT

BCKI
C4M
VDD

VDD
VSS

VSS

BCK
GFS
COMP.
DFCTO IFB1-6 FS1-4 TG1-2 TM1-7 PS1-4
TZC 49 – BAL1-4 ISET 17 ISET 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
+ TOG1-4
DFCT
TZC COMP.
TM1
VCC VCC
TDFCT 50 TRACKING 16 SL_O
VCC PHASE COMPENSATION NC 81 50 LRCK
TG1 TM4 TM6
AVSS 82 49 WDCK
+ AVDD 83 48 ASYE
VC 51 – 15 SL_M
So VCC
TM7
AOUT1 84
– ASYMMETRY
47 ASYO
VCC VEE AIN1 85 46 ASYI
FOCUS FS1 TM5 – CORRECTOR

PWM
TM3 +

3RD-ORDER NOISE SHAPER

PHASE COMPENSATION
FZC 52 +
–
14 SL_P LOUT1 86 + 45 BIAS
+
–
VEE VEE AVSS 87 44 RF
+ FS2 TM2 ERROR
DFCT – Charge XVDD 88 CORRECTOR 43 AVDD
up FSET D/A
FZC COMP. XTAI 89 EFM INTERFACE 42 CLTV
TG2
DEMODURATOR DIGITAL
–

FS4
+

XTAO 90 – 41 AVSS
PLL

PWM
VEE XVSS 91 – + 40 FILI
1 2 3 4 5 6 7 8 9 10 11 12 13 +
AVSS 92 16K RAM DIGITAL OUT 39 FILO
FEO

FEI

FDFCT

FGD

FLB

FE_O

FE_M

SRCH

TGU

TG2

FSET

TA_M

TA_O

LOUT2 93 38 PCO
AIN2 94 OSC 37 VCTL
AOUT2 95 36 V16M
AVDD 96 35 VCKI
SERIAL-IN OVER SAMPLING SUB CODE
CLOCK
AVSS 97 INTERFACE DIGITAL FILTER PROCESSOR 34 VPCO1
GENERATOR
ek

NC 98 33 VPCO2
NC 99 TIMING SERVO 32 TES1
LOGIC CPU
XRST 100 AUTO DIGITAL CLV 31 TES0
INTERFACE
SEQUENCER

1
VDD 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
VSS
LMUT
RMUT
TES2
CKOUT
SQCK
SQSO
SENS
DATA
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
CLKO
SPOA
SPOB
SPOC
SPOD
XLON
FOK
VDD
VSS
MON
MDP
MDS
LOCK
PWMI
– 83 – – 84 –
– TUNER Section – – PANEL Section –

IC1 LC72130 IC761 M65850P

LPF2OUT
OP2OUT
LPF2IN
CLOCK
AOUT2

AOUT1

OP2IN
XOUT

AMIN
FMIN
AIN2

AIN1

VCC
VDD

REF
VSS

PD2

PD1

IO2
24 23 22 21 20 19 18 17 16 15 14 13 14 13 12 11 10 9 8

OSCILLATOR
PHASE DETECTOR D/A LPF2
CHARGE PUMP
1/2 VCC
UNLOCK CLOCK DO1
POWER MO
DETECTOR ON AUTO MAIN 20KBIT
1/2 RESET
RESET RESET CONTROL SRAM
REFERENCE SWALLOW COUNTER MI
D1 DO0
DIVIDER 1/16, 1/17 4BITS

A/D

et
LPF1
12BITS PROGRAMMABLE
DRIVER 1 2 3 4 5 6 7

LPF1IN

LPF1OUT

OP1OUT
OP1IN
CC1

CC2

GND
.n
C 2B UNIVERSAL
I/F DATA SHIFT REGISTER LATCH
COUNTER

1 2 3 4 5 6 7 8 9
nd 10 11 12
XIN
BO5
CE
D1
CL
D0

BO1

BO2

BO3

BO4

IO1

IFIN
ou

IC2 LA1835
AMP-IN R
AM-RF-IN

AMP-IN L
AM. CUT
AM-OSC

FM-AFC

MPX-IN
AM/FM
FM-SD

OUT R

OUT L
AGC

VCO
kS

R
L

30 29 28 27 26 25 24 23 22 21 20 19 18 17 16

ALC AM AM AM DECODER
OSC MIX RF. AMP ANTI BIRDIE
BUFF
STEREO
AGC SW
S METER STEREO
DRIVE
TRIG
Le

FM AM MUTE
IF DET FF FF FF

AM/FM VCO
PILOT
LEVEL IF COMP DET
S-CURVE BUFF
DET AM/FM PHASE
TUNING SW DET
FM FM DRIVE AM
IF DET
FM
REG GND VCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FM-IN

AM-MIX
IF

REG
AM-IF

GND

TU-LED

ST-LED

DET

VCC

IF-BUFF

AM. SD

AM. SD

AM/FM

VCO-STOP

– 85 –
6-18. IC PIN FUNCTION DESCRIPTION
MAIN BOARD IC301 µPD780018Y (MAIN CONTROL)

Pin No. Pin Name I/O Function

1 TA-MUTE O Line mute signal output
2 DBFB-H/L O DBFB H/L select signal output
3 427-LT O Latch signal output for IC201 (62427)
4 KCON-LT O Latch signal output for IC501 (Key Control)
5 KCON-ON/OFF O Key control ON/OFF signal output
6 F-RELAY O Front speaker relay control output
7 R-RELAY O
Not used
8 PL-RELAY O

et
9 TEST I Connected ground
10 X2 O
X’tal (5MHz)
11 X1 I
12 VDD – Power supply (+5V)

.n
13 XT2 O
X’tal (32.768 KHz)
14 XT1 I
15 RESET I Reset signal input
16 INT/IN I
Connected ground
17
18
INT/IN/OUT
SCOR O
I
nd
Subcode data request signal output
19 SOFT-TEST O Software test port
20 AC-CUT I Back up signal input
21 RDS-INT I
Not used
22 RDS-DATA I
ou

23 VDD – Power supply (+5V)

24 AVDD I Analog reference voltage input
25 ADJ I CD adjust point port
26 A-SHUT I A Deck reel pulse detector
27 B-SHUT I B Deck reel pulse detector
kS

28 B-HALF I Half detector signal input

29 CLK-CHECK I Connected ground
30 SPEC-IN I Version select signal input
31 ADJ 2 I Connected ground
32 DEMO-MODE I Connected ground
Le

33 AVss – Ground
34 SQ-DATA-IN I Subcode Q data input
35 — – Not used
36 SQ-CLK I Subcode Q data clock input
37 SW-ON/OFF O Not used
38, 39 FUNC 1, 2 I Connected ground
40 Vss – Ground
41 VOL-LAT O
Not used
42 PL-LAT O
43 COM-DIN I Connected ground
44 COM-DOUT O Common serial data output

– 86 –
Pin No. Pin Name I/O Function
45 COM-CLK O Common serial clock output
46 CD-POWER O CD power on signal output
47 CD-DATA O CD data output
48 CD-CLOK O CD clock output
49 MSM-CMD O Not used
50 MSM-BUSY I Connected ground
51 MSM-LT O
52 MSM-NAR I Not used
53 MSM-CH O
54 INPUT-CHANGE O Not used

et
55 11C-DATA O Data output for IC601
56 11C-CLK O Clock output for IC601
57 XRST O CD reset signal output
58 XLT O CD latch signal output

.n
59 FOUCUS-SW O Not used
60 TBL-L O
Table motor control output
61 TBL-R O
62 TRAY-LED O CD tray LED ON/OFF output
63
64
LOAD-OUT
LOAD-IN
O
O
Not used
nd
65 ST-CLK O Tuner clock output
66 ST-DIN I Tuner data input
67 ST-DOUT O Tuner data output
68 ST-CE O Tuner chip enable output
ou

69 TUNED I Tuned detection for tuner

70 STEREO I Stereo detection for tuner
71 Vss – Ground
72 ST-MUTE O Tuner mute signal output
73 SENS2 I
kS

BD Condition signal input

74 SENS I
75 DISC-SENS I Not used
76 T-SENS I CD table detection signal input
77 UP-SW I Up SW (S201) signal input
78 ENC 3 I
Le

79 ENC 2 I Not used

80 ENC 1 I
81 OUT-OPEN I Not used
82 CAP-M-H/N O Capstan motor H/N speed select signal output
83 B-TRG O Trigger motor control output
84 A-TRG O Trigger motor control output
85 TRG-LOW O Trigger motor control output
86 CAP-M-ON/OFF O Capstan motor ON/OFF signal output
87 PB-A/B O PB Deck A/Deck B select output

– 87 –
Pin No. Pin Name I/O Function
88 EQ-H/N O Equalizer H/N select output
89 BIAS O Bias ON/OFF signal output
90 REC-MUTE O REC mute ON/OFF selection output
91 NR-ON/OFF O NR ON/OFF signal output
92 R/P-PASS O REC/PB/PASS selection output
93 TC-MUTE O TC mute ON/OFF selection output
94 A-PLAY-SW I Deck A play detect
95 B-PLAY-SW I Deck B play detect
96 TC-RELAY O REC/PB head selection output for IC602

et
97 A-HALF I Deck A cassette detect
98 POWER O POWER ON/OFF signal output
99 SW-F-CHG O Super woofer mode signal output
100 STK-MUTE O Power amp ON/OFF signal output

.n
nd
ou
kS
Le

– 88 –
PANEL BOARD IC601 TMP87CH74 (DISPLAY CONTROL)

Pin No. Pin Name I/O Function

1-6 LED3-LED8 O LED driver output
7 VSS – Ground
8 X-OUT O
X’tall (8MHz)
9 X-IN I
10 RESET I Reset signal input from main controller
11 LED 9 O
12 LED10 O Connected ground
13 TEST I
14-19 LED11-LED19 O LED driver output

et
20 VOL-A I Rotary encoder (S701 VOLUME) pulse input
21 DOOR SW I DOOR SW (S651) ON/OFF signal input
22 JOG-A I Rotaly encoder (S711 AMS) pulse input
23 CLOCK I Serial clock input from main controller

.n
24 DATA I Serial data input from main controller
25 LED SELECT O LED select signal output
26 MODEL I Version select signal input
27-30 KEY1-KEY4 I Key input
31
32
SPEANA-3
L+R
I
I
nd
Connected ground
Spectrum analyzer (high frequency) input
33 SIRCS I Remote commander signal input
34 VOL-B I Rotary encoder (S701 VOLUME) pulse input
35 JOG-B I Rotary encoder (S711 AMS) pulse input
ou
36 SPEANA-1 I Spectrum analyzer (Low frequency) input
37 SPEANA-2 I Spectrum analyzer (Middle frequency) input
38 VASS – Ground
39 VAREF I Analog reference voltage input
40 VDD – Power supply (+5V)
kS

41 — – Not used
42-56 GR1-GR15 O FL gride signal output
57-77 SEG1-SEG77 O FL segment signal output
78 VKK – –30V driving power for FL
79, 80 LED1-LED2 O LED driver output
Le

– 89 –
HCD-XB3K

et
.n
nd
ou
kS
Le

Sony Corporation 97E057023-1

9-960-929-11 Home A&V Products Company Printed in Singapore © 1997. 5
Published by General Engineering Dept.
– 114 – (Shibaura)