C1n Super WiFi CPE

802.11n Capable, with Bandwidth Control

and Remote Management Capabilities

The Altai C1n WiFi CPE is designed as an essential much as 16 dB. The C1n can be installed exactly
component in the Altai Super WiFi system to extend where the signal strength requirement is the greatest.
outdoor WiFi coverage into indoor areas for This allows an increase in the coverage distance from
broadband connectivity. the A8/A8n series base station substantially and
provides greater flexibility and savings compared to
the initial WiFi coverage provided by the A8/A8n
alone.

From day one, the C1n is designed and purpose-built

for service operators. Its built-in traffic shaping based
bandwidth control mechanism allows the control of
uplink and downlink traffic throughput on a per-client
or per-VAP basis. WDS, VPN pass-through and a full set
of networking and management features are
available to meet carriers’ requirements.

The C1n is a key component in wireless broadband

access provisioning. It can be installed outdoors by the
side of a window, mounted to a wall, at the rooftop of
a building or placed at the desktop inside for fixed
broadband access provisioning.

The C1n can also be used as a standalone WiFi Access

Point for smaller networks supporting 802.11b/g/n
The Altai C1n employs patented smart signal clients. With its high gain built-in smart antenna, it is an
processing algorithms and antenna design to important solution to complement the large coverage
increase WiFi signal strength (transmit and receive) and high throughput of an A8n series Super WiFi Base
as well as the client’s throughput in areas covered Station and A2 Access Point to improve WiFi
by an A8/A8n Super WiFi Base Station or A2 Smart performance.
WiFi Access Point. It enables network operators to
take advantage of the cost savings provided by The Altai C1n WiFi CPE is the most cost effective and
the A8/A8n series’ 10X greater coverage area, or versatile way to replace traditional last mile access.
the A2’s cost effective high capacity when initially When combined with the A8n series Super WiFi Base
installing the WiFi system. Station and A2 WiFi AP/Bridge, it can be used to build
a high capacity WiFi system that achieves the fastest
With powerful built-in antennas, the C1n WiFi CPE ROI for both telecom operators and enterprises.
can be used to improve the link budget by as

As an integral part of our Super WiFi network infrastructure, the Altai C1n WiFi CPE/AP differentiates others with:

Features built-in for carriers including per client/VAP
One-piece weatherproof chassis compliant to IP55
based bandwidth control, remote web-based standard for direct outdoor installation
management and client performance statistics

8-level LED for easy alignment in the strongest signal

±45 cross-polarized patch antennas are optimized to
° direction
match with the Altai A8/A8n series antennas. It provides 3
dB more gain as compared to other V-H polarized CPEs
Increase signal strength for both NLOS and LOS
coverage areas

High performance antenna with 20 dB front-to-back ratio,
which is on average 5 dB better than others in directional
Improve data transmission rate and throughput utilization
transmission without picking up unwanted signal of base station

© 2013 Altai Technologies Limited. All rights reserved.

Altai C1n Super WiFi CPE

Wireless Interface Physical Specification

802.11b/g/n (2x2) Radio • Dimension 220 x 80 x 24 mm
• Operating Mode AP/CPE/Bridge*/Repeater (excluding mounting)
• Standard IEEE 802.11b/g/n • Weight 0.4 kg
• Operating Frequency 2.412 – 2.472 GHz (Ch 1-13) • Mounting Desktop, Pole, Wall or
• Transmit Power 29 dBm (Max.) Window-mounted
26 dBm (Per Chain) • LED Display Main Power Status
• Receiver Sensitivity (Typical) Ethernet Status
802.11b 11 Mbps -91 dBm 8-level Signal Strength
1 Mbps -96 dBm (User configurable)
802.11g 54 Mbps -81 dBm
6 Mbps -95 dBm Environmental Specification
802.11n HT20 -95 dBm
• Operating Temperature -20 °C to +55 °C
HT40 -92 dBm
• Storage Temperature -40 °C to +80 °C
• Transmit and Receive Diversity
• Humidity 5 – 95% (Non-condensing)
• Altai AirFi™ Throughput Optimization*
• Wind Loading 90 mph (Operational)
• Automatic Channel Selection (with Scheduling*)
125 mph (Survival)
• Site Survey Channel Scan • Weatherproof Outdoor UV Stabilized Plastic
IP55 Compliant
Antenna

Built-in 2.4 GHz Antenna 10 dBi ±45° X-pol Patch Certification

3-dB Horizontal Beamwidth 70° • FCC

3-dB Vertical Beamwidth 30° • CE
• Others*

Front-to-back Ratio 20 dB (Typical)

Networking Antenna Pattern (Built-in Antennas)

-45°
• 8 Multiple SSID/ Virtual AP
• Bandwidth Control/ VAP/ Client
• DHCP Client/ Server
• Dynamic NAT
• 10/100 Mbps Ethernet Port
• Port Forward
• Preferred AP Association
• Auto ACK Timeout Calculation by Distance Input
• Web Based Antenna Alignment Tool
• 2 User Access Levels for Web Login (3 Levels*)
• WMM*
+45°
Security
• Authentication Open system, Shared key,
WPA/ WPA-PSK
WPA2/ WPA2-PSK
802.1x, PEAP
• Encryption WEP, TKIP, AES
• MAC based Access Control
• SSID Suppression

Management
• Web-based Administration Tool Product Ordering Information
• Web-based Antenna Alignment Tool
Standard Package
• Telnet Management (SSH)*
C1n Super WiFi CPE With Built-in 2.4 GHz Patch Antennas
• Remote Firmware Upgrade (HTTP) (Model No.: WA1011N-G)
• SNMP v2c
DC Injector and AC Adaptor
• WiFi Client Association Status
Table Stand and Wire Clamp
• Altai Wireless Management System (AWMS) Support Power Cord Options (country dependent)

UK, US and CN
Power Supply
• Power Source DC Injector
• Power Consumption 6 W (Max.)

Altai Technologies Limited

www.altaitechnologies.com
* Features will be available in future release C1n-PB-130225
Although Altai has attempted to provide accurate information in these materials, Altai assumes no legal liability for the accuracy and completeness of the information.
All specifications are subject to change without notice.