OPERATOR’S

MANUAL

Model 336, 338, & 339

Soft Serve Freezers

Original Operating Instructions

036029- M
4/16/09 (Original Publication)
(Updated 7/16/15)
Complete this page for quick reference when service is required:

Taylor Distributor:

Address:

Phone:

Service:

Parts:

Date of Installation:

Information found on the data label:

Model Number:

Serial Number:

Electrical Specs: Voltage Cycle

Phase

Maximum Fuse Size: A

Minimum Wire Ampacity: A

E 2009 Carrier Commercial Refrigeration, Inc.

036029- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be
a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory
Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties.
All rights reserved.

Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
 Table of Contents

Section 1 To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Section 2 To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Section 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Section 4 Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Model 336 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Model 338 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Model 339 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Three Spout Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Section 5 Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Indicator Light - “Mix Low” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Mix Refrigeration Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
“Standby” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
“Wash” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
“Auto” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Air Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adjustable Draw Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Section 6 Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Draining Product From the Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table of Contents Models 336, 338 & 339

 Table of Contents - Page 2

Section 7 Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Section 8 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Section 9 Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Section 10 Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Section 11 Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Note: Continuing research results in steady improvements; therefore, information

in this manual is subject to change without notice.

Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.

E 2009 Carrier Commercial Refrigeration, Inc. (Original Publication)

Updated July, 2015
036029- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work
may be a violation of Copyright Law of the United States of America and other countries, could result in the
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further
civil and criminal penalties.
All rights reserved.

Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072

Models 336, 338 & 339 Table of Contents

Section 1 To the Installer
The following information has been included in the
manual as safety and regulatory guidelines. For
complete installation instructions, please see the This unit has many sharp edges that can
Installation Checklist. cause severe injuries.

Site Preparation
Installer Safety
Review the area where the unit will be installed before
uncrating the unit. Make sure that all possible hazards
to the user and the equipment have been addressed.
In all areas of the world, equipment should be
installed in accordance with existing local codes.
Please contact your local authorities if you have any Air Cooled Units
questions.
DO NOT obstruct air intake and discharge openings:
Care should be taken to ensure that all basic safety Air cooled units require a minimum of 3” (76 mm) of
practices are followed during the installation and clearance around all sides of the freezer to allow for
servicing activities related to the installation and adequate air flow across the condenser(s). Failure to
service of Taylor equipment. allow adequate clearance can reduce the refrigeration
capacity of the freezer and possibly cause permanent
S Only authorized Taylor service personnel damage to the compressor.
should perform installation and repairs on
the equipment. For Indoor Use Only: This unit is designed to operate
S Authorized service personnel should consult indoors, under normal ambient temperatures of
OSHA Standard 29CFRI910.147 or the 70_-75_F (21_-24_C). The freezer has successfully
applicable code of the local area for the performed in high ambient temperatures of
industry standards on lockout/tagout 104_(40_C) at reduced capacities.
procedures before beginning any installation
or repairs.
S Authorized service personnel must ensure This unit must NOT be installed in an area
that the proper PPE is available and worn where a water jet or hose can be used. NEVER use a
when required during installation and water jet or hose to rinse or clean the unit. Failure to
service. follow this instruction may result in electrocution.
S Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment. This unit must be installed on a level surface
to avoid the hazard of tipping. Extreme care should be
taken in moving this equipment for any reason. Two or
The main power supply(s) to the freezer must more persons are required to safely move this unit.
be disconnected prior to performing any repairs. Failure to comply may result in personal injury or
Failure to follow this instruction may result in personal equipment damage.
injury or death from electrical shock or hazardous
Uncrate the unit and inspect it for damage. Report any
moving parts as well as poor performance or damage
damage to your Taylor Distributor.
to the equipment.
This piece of equipment is made in the USA and has
Note: All repairs must be performed by an USA sizes of hardware. All metric conversions are
authorized Taylor Service Technician. approximate and vary in size.

131122

Models 336, 338 & 339 1 To the Installer

Water Connections Each unit requires one power supply for each data
(Water Cooled Units Only) label on the unit. Check the data label(s) on the freezer
for branch circuit overcurrent protection or fuse, circuit
ampacity, and other electrical specifications. Refer to
An adequate cold water supply must be provided with the wiring diagram provided inside of the electrical box
a hand shut- off valve. On the underside rear of the for proper power connections.
base pan, two 1/2” I.P.S. water connections for inlet
and outlet have been provided for easy hook- up. 1/2”
inside diameter water lines should be connected to the
machine. (Flexible lines are recommended, if local CAUTION: THIS EQUIPMENT MUST BE
codes permit.) Depending on local water conditions, it PROPERLY GROUNDED! FAILURE TO DO SO
may be advisable to install a water strainer to prevent CAN RESULT IN SEVERE PERSONAL INJURY
foreign substances from clogging the automatic water FROM ELECTRICAL SHOCK!
valve. There will be only one water “in” and one water
“out” connection for both single- head and
double- head units. DO NOT install a hand shut- off
valve on the water “out” line! Water should always flow DO NOT operate this freezer with larger fuses
in this order: first, through the automatic water valve; than specified on the unit data label. Failure to follow
second, through the condenser; and third, through the this instruction may result in electrocution or damage
outlet fitting to an open trap drain. to the machine.

This unit is provided with an equipotential

A back flow prevention device is required grounding lug that is to be properly attached to the rear
on the incoming water connection side. Please of the frame by the authorized installer. The installation
refer to the applicable National, State, and local codes location is marked by the equipotential bonding
for determining the proper configuration. symbol (5021 of IEC 60417-1) on both the removable
panel and the equipments frame.

Electrical Connections
Stationary appliances which are not equipped
In the United States, this equipment is intended to be with a power cord and a plug or another device to
installed in accordance with the National Electrical disconnect the appliance from the power source must
Code (NEC), ANSI/NFPA 70-1987. The purpose of the have an all-pole disconnecting device with a contact
NEC code is the practical safeguarding of persons and gap of at least 3 mm installed in the external
property from hazards arising from the use of installation.
electricity. This code contains provisions considered
necessary for safety. In all other areas of the world,
equipment should be installed in accordance with the Appliances that are permanently connected to
existing local codes. Please contact your local fixed wiring and for which leakage currents may
authorities. exceed 10 mA, particularly when disconnected or not
used for long periods, or during initial installation, shall
have protective devices such as a GFI, to protect
FOLLOW YOUR LOCAL ELECTRICAL CODES! against the leakage of current, installed by the
authorized personnel to the local codes.

101012

To the Installer 2 Models 336, 338 & 339

 Refrigerant
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or other equivalent synthetic In consideration of our environment, Taylor
elastomer-sheathed cord (Code designation 60245 proudly uses only earth friendly HFC refrigerants. The
IEC 57) installed with the proper cord anchorage to HFC refrigerant used in this unit is R404A. This
relieve conductors from strain, including twisting, at refrigerant is generally considered non-toxic and
the terminals and protect the insulation of the non-flammable, with an Ozone Depleting Potential
conductors from abrasion. (ODP) of zero (0). However, any gas under pressure
is potentially hazardous and must be handled with
If the supply cord is damaged, it must be replaced by caution.
the manufacturer, its service agent, or similarly NEVER fill any refrigerant cylinder completely with
qualified person, in order to avoid a hazard. liquid. Filling the cylinder to approximately 80% will
allow for normal expansion.

Use only R404A refrigerant that conforms to

Beater Rotation the AHRI standard 700 specification. The use of any
other refrigerant may expose users and operators to
unexpected safety hazards.

Refrigerant liquid sprayed onto the skin may

Beater rotation must be clockwise as viewed cause serious damage to tissue. Keep eyes and skin
looking into the freezing cylinder of any model freezer. protected. If refrigerant burns should occur, flush
Note: The following procedures should be performed immediately with cold water. If burns are severe, apply
by a trained service technician. ice packs and contact a physician immediately.
Taylor reminds technicians to be cautious of
government laws regarding refrigerant recovery,
To correct rotation on a three- phase unit, interchange
any two incoming power supply lines at freezer main recycling, and reclaiming systems. If you have any
questions regarding these laws, please contact the
terminal block only.
factory Service Department.

To correct rotation on a single- phase unit, change the

leads inside the beater motor. (Follow diagram printed
on motor.) WARNING: R404A refrigerant used in
conjunction with polyolester oils is extremely moisture
absorbent. When opening a refrigeration system, the
Electrical connections are made directly to the maximum time the system is open must not exceed 15
terminal block provided in the main control box located minutes. Cap all open tubing to prevent humid air or
behind the service panel. water from being absorbed by the oil.

130809

Models 336, 338 & 339 3 To the Installer

Section 2 To the Operator

The freezer you have purchased has been carefully compliant with the EU Directive as well as other similar
engineered and manufactured to give you dependable legislation in effect after August 13, 2005. Therefore,
operation. The Taylor soft- serve models covered in it must be collected separately after its use is
this manual consist of the following: 336, 338 and 339. completed, and cannot be disposed as unsorted
municipal waste.
These units, when properly operated and cared for, will
produce a consistent quality product. Like all The user is responsible for returning the product to the
mechanical products, they will require cleaning and appropriate collection facility, as specified by your local
maintenance. A minimum amount of care and code.
attention is necessary if the operating procedures For additional information regarding applicable local
outlined in this manual are followed closely. laws, please contact the municipal facility and/or local
distributor.
This Operator’s Manual should be read before
operating or performing any maintenance on your Compressor Warranty Disclaimer
equipment.
The refrigeration compressor(s) on this unit are
Your Taylor freezer will NOT eventually compensate warranted for the term stated in the Limited Warranty
for and correct any errors during the set- up or filling section in this manual. However, due to the Montreal
operations. Thus, the initial assembly and priming Protocol and the U.S. Clean Air Act Amendments of
procedures are of extreme importance. It is strongly 1990, many new refrigerants are being tested and
recommended that personnel responsible for the developed, thus seeking their way into the service
equipment’s operation, both assembly and industry. Some of these new refrigerants are being
disassembly, go through these procedures together in advertised as drop- in replacements for numerous
order to be properly trained and to make sure that no applications. It should be noted that in the event of
confusion exists. ordinary service to this unit’s refrigeration system,
only the refrigerant specified on the affixed data
In the event you should require technical assistance,
label should be used. The unauthorized use of
please contact your local authorized Taylor Distributor.
alternate refrigerants will void your Taylor compressor
Note: Your Taylor warranty is valid only if the parts are warranty. It is the unit owner’s responsibility to make
authorized Taylor parts, purchased from the local this fact known to any technician he employs.
authorized Taylor Distributor, and only if all required It should also be noted that Taylor does not warrant the
service work is provided by an authorized Taylor refrigerant used in its equipment. For example, if the
service technician. Taylor reserves the right to deny refrigerant is lost during the course of ordinary service
warranty claims on units or parts if non- Taylor to this machine, Taylor has no obligation to either
approved parts or incorrect refrigerant were installed supply or provide its replacement either at billable or
in the unit, system modifications were performed unbillable terms. Taylor does have the obligation to
beyond factory recommendations, or it is determined recommend a suitable replacement if the original
that the failure was caused by abuse, misuse, neglect, refrigerant is banned, obsoleted, or no longer available
or failure to follow all operating instructions. For full during the five year warranty of the compressor.
details of your Taylor Warranty, please see the Limited
Warranty section in this manual. Taylor will continue to monitor the industry and test
new alternates as they are being developed. Should a
Note: Constant research results in steady new alternate prove, through our testing, that it would
improvements; therefore, information in this be accepted as a drop- in replacement, then the above
manual is subject to change without notice. disclaimer would become null and void. To find out the
current status of an alternate refrigerant as it relates to
your compressor warranty, call the local Taylor
Distributor or the Taylor Factory. Be prepared to
If the crossed out wheeled bin symbol is provide the Model/Serial Number of the unit in
affixed to this product, it signifies that this product is question.

131122

To the Operator 4 Models 336, 338 & 339

Section 3 Safety
We at Taylor Company are concerned about the safety
of the operator when he or she comes in contact with
the freezer and its parts. Taylor has gone to extreme
efforts to design and manufacture built- in safety S DO NOT operate the freezer unless it is
features to protect both you and the service technician. properly grounded.
As an example, warning labels have been attached to
S DO NOT operate the freezer with larger
the freezer to further point out safety precautions to the
fuses than specified on the data label.
operator.
S All repairs must be performed by an
authorized Taylor service technician.
S The main power supplies to the machine
IMPORTANT - Failure to adhere to the must be disconnected prior to performing
following safety precautions may result in severe any repairs.
personal injury or death. Failure to comply with S Cord Connected Units: Only Taylor
these warnings may damage the machine and its authorized service technicians may install a
components. Component damage will result in plug on this unit.
part replacement expense and service repair S Stationary appliances which are not
expense. equipped with a power cord and a plug or
another device to disconnect the appliance
from the power source must have an all-pole
disconnecting device with a contact gap of
DO NOT operate the freezer without reading at least 3 mm installed in the external
this Operator Manual. Failure to follow this instruction installation.
may result in equipment damage, poor freezer S Appliances that are permanently connected
performance, health hazards, or personal injury. to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
This appliance is to be used only by trained
have protective devices such as a GFI, to
personnel. It is not intended for use by children or
protect against the leakage of current,
people with reduced physical, sensory, or mental
installed by the authorized personnel to the
capabilities, or lack of experience and knowledge,
local codes.
unless given supervision or instruction concerning the
use of the appliance by a person responsible for their S Supply cords used with this unit shall be
safety. Children should be supervised to ensure that oil-resistant, sheathed flexible cable not
they do not play with the appliance. lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer-sheathed cord (Code designation
60245 IEC 57) installed with the proper cord
This unit is provided with an equipotential anchorage to relieve conductors from strain,
grounding lug that is to be properly attached to the rear including twisting, at the terminals and
of the frame by the authorized installer. The installation protect the insulation of the conductors from
location is marked by the equipotential bonding abrasion.
symbol (5021 of IEC 60417-1) on both the removable If the supply cord is damaged, it must be
panel and the equipments frame. replaced by the manufacturer, its service
agent, or similarly qualified person, in order
to avoid a hazard.

DO NOT use a water jet to clean or rinse the Failure to follow these instructions may result in
freezer. Failure to follow these instructions may result electrocution. Contact your local authorized Taylor
in serious electrical shock. Distributor for service.

130318

Models 336, 338 & 339 5 Safety

 Cleaning and sanitizing schedules are
S DO NOT allow untrained personnel to governed by your state or local regulatory agencies
operate this machine. and must be followed accordingly. Please refer to the
cleaning section of this manual for the proper
S DO NOT operate the freezer unless all
procedure to clean this unit.
service panels and access doors are
restrained with screws.
S DO NOT remove any internal operating
parts (examples: freezer door, beater, This machine is designed to maintain product
scraper blades, etc.) unless all control temperature under 41_F (5_C). Any product being
switches are in the OFF position. added to this machine must be below 41_F (5_C).
Failure to follow these instructions may result in severe Failure to follow this instruction may result in health
personal injury to fingers or hands from hazardous hazards and poor freezer performance.
moving parts.
DO NOT obstruct air intake and discharge openings:
3” (76 mm) minimum air space on sides and rear, and
This unit has many sharp edges that can 7- 1/2” (191 mm) on the bottom. The Model 338
cause severe injuries. requires 4- 1/4” (108 mm) on the bottom.
S DO NOT put objects or fingers in the door
Failure to follow this instruction may cause poor
spout. This may contaminate the product freezer performance and damage to the machine.
and cause severe personal injury from blade
contact.
S USE EXTREME CAUTION when removing For Indoor Use Only: This unit is designed to operate
the beater asssembly. The scraper blades indoors, under normal ambient temperatures of 70_ -
are very sharp. 75_F (21_ - 24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
Access to the service area of the unit is
restricted to persons having knowledge and practical DO NOT run the machine without product. Failure to
experience with the appliance, in particular as far as follow this instruction can result in damage to the
safety and hygiene are concerned. machine.

NOISE LEVEL: Airborne noise emission does not

This freezer must be placed on a level exceed 78 dB(A) when measured at a distance of 1.0
surface. Failure to comply may result in personal injury meter from the surface of the machine and at a height
or equipment damage. of 1.6 meters from the floor.

130318

Safety 6 Models 336, 338 & 339

Section 4 Operator Parts Identification
Model 336

Figure 1

ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.

1 COVER A.- HOPPER X37963 12 ADAPTOR A. CASTER X18915
2 PAN- DRIP 17- 1/4”LONG 027504 13 CASTER- SWV 5/8 STEM 4IN 018794
3 PANEL- UPPER SIDE L. 028740 14 CASTER- 4” SWV W/BRAKE 034081
4 ORIFICE 022465- 100 15 PANEL- SERVICE 082483
5 O- RING- 3/8 OD X .070W 016137 16 TRAY- DRIP 16- 7/8L X 5- 1/8 020157
6 TUBE- FEED 5/32 DIA. HOLE 043461- 2 17 SHIELD- SPLASH 022765
7 O- RING- .563 OD X .070W 043758 18 STUD- NOSE 022822
8 PANEL- REAR 029816 19 PANEL A.- FRONT X68530
9 LOUVER- SIDE- TOP 051191 20 DECAL- DEC- TAYLOR 045812
10 PANEL- UPPER SIDE R. 028741 21 PLATE- DEC 041854
11 PANEL A.- LOWER SIDE X24424 22 GASKET- HOPPER COVER 037042

150716

Models 336, 338 & 339 7 Operator Parts Identification

Model 338

Figure 2

ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.

1 COVER A.- HOPPER X38458- SER 10 PANEL- SIDE (LOWER RIGHT) 048487
2 GASKET- HOPPER COVER 038474 11 PANEL A.- SIDE LEFT X51596- SER
3 ORIFICE 022465- 100 12 STUD- NOSE CONE 022822
4 O- RING 3/8 OD x .070 W 016137 13 PANEL A.- FRONT X51590
5 TUBE A.- FEED SS 5/32 HOLE X29429- 2 14 PAN A.- DRIP- 15- 1/8 LONG X51601
6 O- RING .643 OD x .077 W 018572 15 SHIELD- SPLASH 23 LONG 022766
7 PANEL- REAR 051600 16 TRAY- DRIP 22- 7/8 L x 5- 1/8 W 014533
8 LOUVER- SIDE TOP 051191 17 LEG- 4” SS W/O- RING 013458
9 PANEL A.- SIDE UPPER RIGHT X48596 18 SKIRT- AIR FLOW 048489

150716

Operator Parts Identification 8 Models 336, 338 & 339

Model 339

Figure 3

ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.

1 COVER A.- HOPPER- STD X38458- SER 11 PAN- DRIP 17- 1/4” LONG 027504
2 GASKET- HOPPER COVER 038474 12 PANEL- UPPER SIDE LEFT 028740
3 ORIFICE 022465- 100 13 STUD- NOSE CONE 022822
4 O- RING 3/8 OD X .070 W 016137 14 PANEL A.- FRONT X32956
5 TUBE A.- FEED SS 5/32 HOLE X29429- 2 15 ADAPTOR A.- CASTER X18915
6 O- RING .643 OD X . 077 W 018572 16 CASTER- SWV 5/8 STEM 4” 018794
7 PANEL- REAR 053782 17 Caster- 4” SWV W/BRAKE 034081
8 LOUVER- SIDE TOP 051191 18 PANEL- SERVICE 024439
9 PANEL- UPPER SIDE RIGHT 028741 19 SHIELD- SPLASH 23 L 022766
10 PANEL A.- LOWER SIDE (R/L) X24424 20 TRAY- DRIP 22- 7/8L X 5- 1/8 W 014533

150716

Models 336, 338 & 339 9 Operator Parts Identification

Three Spout Door

Figure 4

ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.

1 SEAL- DRIVE SHAFT 032560 9c O- RING- 1/4 OD X .070W 50 015872
2 SHAFT- BEATER 033235 10 NUT- STUD 034382
3 BEATER A.- 2.8QT- HELICORE X35466 11 NUT- STUD 034383
4 BLADE- SCRAPER- PLASTIC 035480 12 VALVE A.- DRAW X69539
5 BEARING- FRONT 050216 13 O- RING- 13/16 OD X .103W 019330
6 GASKET- DOOR HT 4”- DOUBLE 048926 14 CAP- DESIGN 1.010”ID- 6 POINT 014218
7 O- RING- 3/8 OD X .070W 016137 15 O- RING- 5/16 OD X .070W 016272
8 PLUG- PRIME 028805 16 ROD A.- PIVOT X20683
9 HANDLE A.- DRAW *WHITE X81010- SP 17 DOOR A.- 3 SPOUT X51532- 15
9a HANDLE A.- ADJ. *THREADED X80889- SP 17a BAFFLE A.- SHORT 4 IN W/RAD X50883
9b SCREW- ADJUSTMENT 056332

Operator Parts Identification 10 Models 336, 338 & 339

Accessories

Figure 5

ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.

1 TOOL- ORING REMOVAL 048260- WHT 7 PAIL- 10 QT. (336 & 339) 013163
2 BRUSH- REAR BEARING 013071 8 PAIL- 6 QT. (338) 023348
1” D X 2” L
9 DEFLECTOR- BLOWER (339) 047912
3 BRUSH- DOUBLE ENDED 013072
10 SKIRT- AIR FLOW (338) 048489
4 BRUSH- DRAW VALVE 013073
1” X 2” X 17” 11 DEFLECTOR- BLOWER - 048345
SIDE DISCHARGE (336)
5 BRUSH- MIX PUMP BODY 023316
3” x 7” *Item 6: A sample of Kay- 5 or Stera Sheen is shipped
with new equipment. Order additional sanitizer, using
SANITIZER- KAY- 5 (200 PK) 041082 one of the part numbers listed.
*6 SANITIZER- STERA SHEEN 055492
(100 PK)

140717

Models 336, 338 & 339 11 Operator Parts Identification

Section 5 Important: To the Operator

ITEM DESCRIPTION
1 POWER SWITCH
2 MIX REFRIGERATION BUTTON
3 STANDBY BUTTON
4 WASH BUTTON
5 AUTO BUTTON
6 INDICATOR LIGHT “MIX LOW”
7 RESET BUTTON

Symbol Definitions

The following chart identifies the symbol definitions used on the operator switches.

= ON = WASH

= OFF = MIX LOW

= MIX = STANDBY

Important: To the Operator 12 Models 336, 338 & 339

Power Switch When the “STANDBY” button is pressed, the light
comes on, indicating the CTR (Cylinder Temperature
Retention System) feature has been activated. In the
When placed in the “ON” position, the power switch
“STANDBY” mode, the “WASH” and “AUTO” functions
allows SOFTECHR control panel operation. are automatically cancelled. The mix refrigeration
function is automatically locked in to maintain the mix
in the hopper.
Indicator Light - “Mix Low”
To resume normal operation, press the “AUTO” button.
Located on the front of the machine is a mix level When the unit cycles off, the product in the freezing
indicating light. When the light is flashing, it indicates cylinder will be at serving viscosity. At this time, place
that the mix hopper has a low supply of mix and should the air tube (end with the hole) into the mix inlet hole
be refilled as soon as possible. Always maintain at and install the air orifice.
least 3” (76 mm) of mix in the hopper. If you neglect to
add mix, a freeze- up may occur. This will cause
eventual damage to the beater, blades, drive shaft,
and freezer door. “Wash”

Mix Refrigeration Button When the “WASH” button is pressed, the light comes
on. This indicates beater motor operation. The
When the mix refrigeration button is pressed, the light “STANDBY” or “AUTO” modes must be cancelled first
comes on indicating the mix hopper refrigeration to activate the “WASH” mode.
system is operating. The mix refrigeration is controlled
by the left side of the freezer as viewed from the
operator end. The mix refrigeration function cannot be
Note: The Model 336 cannot be operated in
cancelled unless the “AUTO” or “STANDBY” modes
the “WASH” mode if the opposite side of the freezer is
are cancelled first.
in “AUTO”. Failure to comply with this instruction will
cause the rinse or sanitizing solution to freeze.
“Standby”
The Separate Hopper Refrigeration System (SHR)
and the Cylinder Temperature Retention System “Auto”
(CTR) are standard features. The SHR feature
incorporates the use of a separate small refrigeration
system to maintain the mix in the hopper below When the “AUTO” button is pressed, the light comes
40_(4.4_C) to assure bacteria control. The CTR on. This indicates that the main refrigeration system
feature works with the SHR to maintain a good quality has been activated. In the “AUTO” mode, the “WASH”
product. During long “No Sale” periods, it is necessary or “STANDBY” functions are automatically cancelled.
to warm the product in the freezing cylinder to The mix refrigeration function is automatically locked
approximately 35_F to 40_F (1.7_C to 4.4_C) to in to maintain the mix in the mix hopper.
prevent overbeating and product breakdown.
To activate the SHR and CTR features, press the Note: An indicating light and an audible tone will
“STANDBY” button. Remove the air orifice and place sound whenever a mode of operation has been
the air tube (end without the hole) into the mix inlet pressed. To cancel any function, press the button
hole. again. The light and mode of operation will shut off.

Models 336, 338 & 339 13 Important: To the Operator

Reset Button 1. After priming the machine, lubricate the o- rings
on the air tube (the end with the hole) and
place it into the mix inlet hole. Every time the
The reset button is located in the service panel. The draw handle is raised, new mix and air from the
reset protects the beater motor from an overload hopper will flow down into the freezing cylinder.
condition. If an overload occurs, the reset mechanism This will keep the freezing cylinder properly
will trip. To properly reset the freezer, press the loaded and will maintain overrun.
“AUTO” button to cancel the cycle. Place the power
switch to the “OFF” position. Press the reset button 2. During long “No Sale” periods, remove the air
firmly. orifice. Lubricate the o- rings on the air tube
(the end without the hole), and place it into
the mix inlet hole. This will prevent any mix
from entering the freezing cylinder.
Note: Do not use metal objects to press the
reset button. Failure to follow this instruction may The air orifice is used to meter a certain amount
result in electrocution. of air into the freezing cylinder. The air orifice
maintains overrun and allows enough mix to enter
Turn the power switch to the “ON” position. Press the the freezing cylinder after a draw.
“WASH” button and observe the freezer’s
performance. Open the side access panel. Make sure
the beater motor is turning the drive shaft in a
clockwise direction (from the operator end) without Adjustable Draw Handle
binding.
If the beater motor is turning properly, press the These units feature an adjustable draw handle to
“WASH” button to cancel the cycle. Press the “AUTO” provide the best portion control. The draw handle
button (on both sides of the unit) to resume normal should be adjusted to provide a flow rate of 5 to 7- 1/2
operation. If the freezer shuts down again, contact a oz. of product per 10 seconds. To INCREASE the flow
service technician rate, turn the screw COUNTERCLOCKWISE. Turn
the screw CLOCKWISE to DECREASE the flow rate.
During “Sanitizing” and “Rinsing”, the flow rate can be
increased by removing the pivot pin and placing the
Air Tube restrictive bar on the TOP. When drawing product,
always place the restrictive bar on the bottom.
The air tube serves two purposes. One end of the tube IMPORTANT! When dispensing product, pull only
has a hole and the other end does not. one draw handle at a time.

Figure 6 Figure 7

091030

Important: To the Operator 14 Models 336, 338 & 339

Section 6 Operating Procedures

Each unit stores mix in a hopper. The mix then flows

by gravity through an air tube down into the freezing
cylinder. They all have 2.8 quart (2.6 liter) capacity DO NOT lubricate the hex end of the drive
freezing cylinders. All models have 20 quart (18.9 liter) shaft. Fill the inside portion of the seal with 1/4” more
mix hoppers. lubricant and lubricate the flat side of the seal that fits
onto the rear shell bearing.
Duplicate the following procedures, where they apply,
for the second freezing cylinder.

We begin our instructions at the point where we enter

the store in the morning and find the parts
disassembled and laid out to air dry from the previous
night’s cleaning.

These opening procedures will show you how to

assemble these parts into the freezer, sanitize them,
and prime the freezer with fresh mix in preparation to
serve your first portion.

If you are disassembling the machine for the first time

or need information to get to this starting point in our
instructions, turn to page 23, “Disassembly”, and start Figure 8
there.
Insert the drive shaft into the freezing cylinder, hex end
first, and into the rear shell bearing until the seal fits
securely over the rear shell bearing. Engage the hex
end firmly into the drive coupling. Be sure the drive
Assembly shaft fits into the drive coupling without binding.

Note: When lubricating parts, use an approved food

grade lubricant (example: Taylor Lube).

MAKE SURE THE CONTROL SWITCH IS

IN THE “OFF” POSITION.

Step 1
Install the drive shaft. Lubricate the groove and shaft
portion that comes in contact with the bearing on the
beater drive shaft. Slide the seal over the shaft and
groove until it snaps into place. Figure 9

Models 336, 338 & 339 15 Operating Procedures

Step 2 Step 3
Take one of the scraper blades and slip it under the Assemble the freezer door. Place the large rubber
hook at the front of the beater. Wrap the blade around gaskets into the grooves on the back side of the
the beater following the helix and pushing the blade freezer door.
down onto the helix as you wrap. At the back end of the
beater, slip the blade under the hook. Repeat this Slide the white plastic front bearings over the baffle
step for the second scraper blade. rods onto the bearing hubs making certain that the
flanged end of the bearing is resting against the freezer
door.

DO NOT LUBRICATE THE GASKETS OR

THE FRONT BEARINGS. Damage to components
may occur.

Figure 10

Holding the beater securely, slide the beater one third

of the way into the freezing cylinder. Looking into the
freezing cylinder, align the hole at the rear of the beater
with the flats on the end of the drive shaft.

Figure 12

Slide the two o- rings into the grooves on the prime

plugs. Apply an even coat of Taylor Lube to the o- rings
and shafts.

Figure 11

Slide the beater the remainder of the way into the

freezing cylinder and over the end of the drive shaft.
The beater should fit snugly, but not so tightly that the
beater cannot be turned slightly to engage the drive
shaft. If the beater slides in too easily with little or no
resistance, there will not be enough force against the
beater to hold the blades in place. If this is the case,
contact your authorized Taylor service agent.

Repeat Steps 1 and 2 for the other side of the freezer. Figure 13

Operating Procedures 16 Models 336, 338 & 339

Insert the prime plugs into the holes in the top of the Step 5
freezer door, and push down. Install the three draw valves. Slide the two o- rings into
the grooves on the draw valves, and lubricate.

Figure 16
Lubricate the inside of the freezer door spouts, top and
bottom, and insert the draw valves from the bottom
Figure 14 until the slot in the draw valves comes into view.

Step 4
Install the freezer door. Insert the baffle rods through
the opening in the beaters and seat the door flush with
the freezing cylinder. With the door seated on the
freezer studs, install the handscrews. Tighten equally
in a crisscross pattern to insure the door is snug.

Note: The short handscrews go on the bottom

and the long handscrews go on top.
Figure 17
Step 6
Install the adjustable draw handles. Slide the o- ring
into the groove on the pivot pin, and lubricate.

Figure 15 Figure 18

Models 336, 338 & 339 17 Operating Procedures

Slide the fork over the bar in the slot of the draw valve. Step 8
Secure with pivot pin. Install the front drip tray and the splash shield under
the door spouts.
Note: The Models 336, 338 and 339 have three draw
handles. Slide the fork of the draw handle in the slot of
the draw valve, starting from the right. Slide the pivot
pin through each draw handle as you insert them into
the draw valves.

Figure 21
Step 9
Slide the rear drip pan into the hole in the side panel
(front panel on a Model 338).

Figure 19

Note: These units feature adjustable draw handles to

provide the best portion control. The draw handles can
be adjusted for different flow rates. See page 14 for
more information on adjusting these handles.

Step 7
Snap the design caps over the end of the door spouts. Figure 22
Step 10
Slide two o- rings on one end of the air tube. Slide two
o- rings on the other end of the air tube.

Figure 20 Figure 23

Operating Procedures 18 Models 336, 338 & 339

Slide the small o- ring into the groove of the air orifice. Sanitizing
Do not lubricate the o- ring.

Step 1
Prepare a pail of approved 100 PPM sanitizing solution
(examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2 gal.
[7.6 liters] of Stera- SheenR). USE WARM WATER
AND FOLLOW THE MANUFACTURER’S SPECIFIC-
ATIONS.

Step 2
Pour the sanitizing solution into the hopper and allow
it to flow into the freezing cylinder.

Figure 24

Note: Make sure the hole in the air orifice is clean and
is not clogged. If the hole in the air orifice should
become clogged, use soap and hot water to clear the
hole.

Do not enlarge the hole in the air orifice.

Install the air orifice into the hole in the top of the air
tube (in the end without the small hole on the side).
Figure 26

Step 3
While the solution is flowing into the freezing cylinder,
brush clean the mix hopper. When cleaning the
hopper, take particular care in brushing the mix level
sensing probe on the rear wall of the hopper, the mix
inlet hole, the air tube, and the hopper gasket.

Figure 25

Step 11
Lay the air tube (with the air orifice installed) and the
hopper gasket in the bottom of the mix hopper for
sanitizing.

Repeat Steps 10 and 11 for the other side of the

freezer. Figure 27

Models 336, 338 & 339 19 Operating Procedures

 Step 6
Place an empty pail beneath the door spout and raise
the prime plug.

Figure 28

Step 4
Place the power switch in the “ON” position.
Figure 31

Step 7
When a steady stream of sanitizing solution is flowing
from the prime plug opening in the bottom of the
freezer door, lower the draw handle. Draw off all the
sanitizing solution.

Figure 29

Step 5
Press the “WASH” button. This will cause the
sanitizing solution in the freezing cylinder to agitate.
Allow it to agitate for five minutes.

Figure 32

Note: Momentarily pull the center draw handle down

to sanitize the center door spout.

Step 8
Once the sanitizer stops flowing from the door spout,
raise the draw handle and press the “WASH” button,
cancelling the beater motor operation.

Note: You have just sanitized the freezer. Be

sure your hands are sanitized before continuing
Figure 30 these instructions.

Operating Procedures 20 Models 336, 338 & 339

Step 9 Step 2
Assemble the hopper gasket around the top edge of Once a steady stream of mix starts to flow from the
the mix hopper. Stand the air tube in the corner of the prime plug opening in the bottom of the freezer door,
hopper. push down the prime plug.

Figure 33
Repeat Steps 1 through 9 for the other side of the
freezer.

Figure 35
Priming
Step 3
Step 1 Lubricate the o- rings on the air tube on the end with
With a pail beneath the door spout, lower the draw the small hole on the side.
handle. Be sure the prime plug is still in the UP
position. Pour two gallons (7.6 liters) of fresh mix into
the mix hopper and allow it to flow into the freezing Step 4
cylinder. This will force out any remaining sanitizing Install the air tube in the “AUTO” position.
solution. When full strength mix is flowing from the
door spout, raise the draw handle.
Note: Use only fresh mix when priming the freezing
cylinder.

Figure 34 Figure 36

Models 336, 338 & 339 21 Operating Procedures

Step 5 Draining Product From the
Press the “AUTO” button. The “AUTO” light will come
on indicating the main refrigeration system is Freezing Cylinder
operating. When the unit cycles off, the product will be Step 1
at serving viscosity. Press the “AUTO” button, cancelling compressor and
beater motor operation.
Press the mix refrigeration button, cancelling the mix
hopper refrigeration system.
Step 2
Remove the hopper cover, hopper gasket and air tube.
Take these parts to the sink for cleaning.
Step 3
If local health codes permit the use of rerun, place
a sanitized, NSF approved stainless steel rerun
container beneath the door spout. Press the WASH
key and lower the draw handle. Drain the remaining
product from the freezing cylinder and mix hopper.
When the flow of product stops, press the WASH key
and raise the draw handle. Place the sanitized lid on
Figure 37 the rerun container and place it in the walk- in cooler.
Note: If local health codes DO NOT permit the use
Note: The mix refrigeration light will come on, of rerun, the product must be discarded. Drain the
indicating the mix refrigeration system is operating to product into a pail and properly discard it.
maintain the mix in the mix hopper.
Repeat Steps 1 through 3 for the other side of the
Step 6 freezer.
Fill the hopper with mix. As the mix level comes in Note: For the Model 336, both sides must be in
contact with the mix level sensing probe on the rear WASH. If one side is in AUTO and the other is in
wall of the hopper, the “MIX LOW” light will shut off. WASH, the side that is in WASH will continue to freeze.

Step 7
Place the mix hopper cover in position over the mix ALWAYS FOLLOW LOCAL HEALTH CODES.
hopper.

Repeat Steps 1 through 7 for the other side of the Rinsing

freezer. Step 1
Pour two gallons (7.6 liters) of cool clean water into the
mix hopper. With the brushes provided, scrub the mix
hopper, mix inlet hole and mix level sensing probe.
Step 2
Closing Procedure With a pail beneath the door spout, raise the prime plug
and press the “WASH” button.
Step 3
To disassemble your unit, the following items will be
When a steady stream of rinse water is flowing from
needed:
the prime plug opening in the bottom of the freezer
S Two cleaning pails door, lower the draw handle. Drain all the rinse water
from the freezing cylinder, raise the draw handle and
S Sanitized stainless steel rerun can with lid
press the “WASH” button, cancelling the “WASH”
S Necessary brushes (provided with freezer) mode.
S Cleaner Repeat Steps 1 through 3 for the other side of the
S Single service towels freezer.

140717

Operating Procedures 22 Models 336, 338 & 339

Cleaning Brush Cleaning
Step 1
Prepare a pail of approved 100 PPM cleaning solution Step 1
(examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2 gal. Prepare a sink with an approved cleaning solution
[7.6 liters] of Stera- SheenR). USE WARM WATER (examples: Kay- 5R or Stera- SheenR). USE WARM
AND FOLLOW THE MANUFACTURER’S SPECIFIC- WATER AND FOLLOW THE MANUFACTURER’S
ATIONS. SPECIFICATIONS. If another approved cleaner is
used, dilute it according to the label instructions.
Step 2 (IMPORTANT: Follow the label directions. Too
Push down the prime plug. Pour the cleaning solution STRONG of a solution can cause parts damage, while
into the mix hopper. too MILD of a solution will not provide adequate
Step 3 cleaning.) Make sure all brushes provided with the
While the solution is flowing into the freezing cylinder, freezer are available for brush cleaning.
brush clean the mix hopper, mix level sensing probe,
and the mix inlet hole. Step 2
Remove the seals from the drive shafts.
Step 4
Press the “WASH” button. This will cause the cleaning Step 3
solution in the freezing cylinder to agitate. From the freezer door remove:
Step 5 S gaskets
Place an empty pail beneath the door spout and raise S front bearings
the prime plug.
S pivot pins
Step 6 S adjustable draw handles
When a steady stream of cleaning solution is flowing
from the prime plug opening in the bottom of the S design caps
freezer door, lower the draw handle. Draw off all of the S draw valves
solution. S prime plugs
Step 7 Remove all o- rings.
Once the cleaner stops flowing from the door spout,
raise the draw handle and press the “WASH” button, Note: To remove o- rings, use a single service towel
cancelling the “WASH” mode. to grasp the o- ring. Apply pressure in an upward
direction until the o- ring pops out of its groove. With
Repeat Steps 1 through 7 for the other side of the
the other hand, push the top of the o- ring forward and
freezer.
it will roll out of the groove and can be easily removed.
Disassembly If there is more than one o- ring to be removed, always
remove the rear o- ring first. This will allow the o- ring
Step 1 to slide over the forward rings without falling into the
open grooves.

BE SURE THE POWER SWITCH IS IN THE

“OFF” POSITION. MAKE SURE NO LIGHTS ARE
LIT ON THE CONTROL PANEL.
Step 2
Remove the handscrews, freezer door, beaters,
scraper blades, and drive shafts from the freezing
cylinders. Take these parts to the sink for cleaning.
Step 3
Remove the front drip tray and the splash shield.

Models 336, 338 & 339 23 Operating Procedures

Step 4 Step 6
Remove the o- rings from the air tubes and air orifices. Remove the rear drip pan and take it to the sink for
Step 5 cleaning.
Return to the freezer with a small amount of cleaning Note: If the drip pan is filled with an excessive amount
solution. Brush clean the rear shell bearings at the of mix, refer to the Troubleshooting Guide.
back of the freezing cylinders with the black bristle
brush. Step 7
Thoroughly brush clean all disassembled parts in the
cleaning solution making sure all lubricant and mix film
is removed. Take particular care to brush clean the
draw valve cores in the freezer door. Place all the
cleaned parts on a clean, dry surface to air dry
overnight.
Step 8
Wipe clean all exterior surfaces of the freezer.

Figure 38

Operating Procedures 24 Models 336, 338 & 339

Section 7 Important: Operator Checklist

During Cleaning and Sanitizing j 6. On a designated day of the week, run the mix as
low as feasible and discard it after closing. This
will break the rerun cycle and reduce the
Cleaning and sanitizing schedules are governed possibility of high bacteria and coliform counts.
by federal, state, or local regulatory agencies, j 7. Properly prepare the cleaning and sanitizing
and must be followed accordingly. If the unit solutions. Read and follow label directions
has a “Standby mode”, it must not be used in carefully. Too strong of a solution may damage
lieu of proper cleaning and sanitizing the parts and too weak of a solution will not do
procedures and frequencies set forth by the an adequate job of cleaning or sanitizing.
ruling health authority. The following check
points should be stressed during the cleaning j 8. The temperature of the mix in the mix hopper
and sanitizing operations. and walk- in cooler should be below 40_F.
(4.4_C.).
WE RECOMMEND DAILY CLEANING AND
SANITIZING.
Regular Maintenance Checks
j 1. Replace scraper blades that are nicked or
ALWAYS FOLLOW LOCAL HEALTH CODES. damaged. Before installing the beater
assembly, be certain that scraper blades are
properly attached to the helix.
j 2. Check the rear shell bearing for signs of wear
(excessive mix leakage in rear drip pan) and be
Troubleshooting Bacterial Count certain it is properly cleaned.
j 3. Using a screwdriver and cloth towel, keep the
j 1. Thoroughly clean and sanitize machine rear shell bearing and the female hex drive
regularly, including complete disassembly and socket clean and free of lubricant and mix
brush cleaning. deposits.
j 4. Dispose of o- rings and seals if they are worn,
j 2. Use all brushes supplied for thorough cleaning. torn, or fit too loosely, and replace with new
The brushes are specially designed to reach all ones.
mix passageways.
j 5. Follow all lubricating procedures as outlined in
j 3. Use the white bristle brush to clean the mix inlet “Assembly”.
hole which extends from the mix hopper down
j 6. If your machine is air cooled, check the
to the rear of the freezing cylinder.
condensers for accumulation of dirt and lint.
j 4. Use the black bristle brush to thoroughly clean Dirty condensers will reduce the efficiency and
the rear shell bearing located at the rear of the capacity of the machine. Condensers should be
freezing cylinder. Be sure to have a generous cleaned monthly with a soft brush. Never use
amount of cleaning solution on the brush. screwdrivers or other metal probes to clean
between the fins.
j 5. IF LOCAL HEALTH CODES PERMIT THE Note: For machines equipped with an air filter,
USE OF RERUN, make sure the mix rerun is it will be necessary to vacuum clean the filters
stored in a sanitized, covered stainless steel on a monthly schedule.
container and used the following day. DO NOT
prime the machine with rerun. When using
rerun, skim off the foam and discard. Mix the Caution: Always disconnect
rerun with fresh mix in a ratio of 50/50 during the electrical power prior to cleaning the
days operation. condenser.

111213

Models 336, 338 & 339 25 Important: Operator Checklist

j 7. If your machine is equipped with an auxiliary Winter Storage
refrigeration system, check the auxiliary
condenser for accumulation of dirt and lint. Dirty If the place of business is to be closed during the winter
condensers will reduce the refrigeration months, it is important to protect the freezer by
capacity of the mix hopper. Condensers must following certain precautions, particularly if the
be cleaned monthly with a soft brush. Never building is subject to freezing conditions.
use screwdrivers or other metal probes to clean Disconnect the freezer from the main power source to
between the fins. prevent possible electrical damage.
On water cooled freezers, disconnect the water
supply. Relieve pressure on the spring in the water
Caution: Always disconnect valve. Use air pressure on the outlet side to blow out
electrical power prior to cleaning the any water remaining in the condenser. This is
condenser. extremely important. Failure to follow this procedure
may cause severe and costly damage to the
j 8. If your machine is water cooled, check the water refrigeration system.
lines for kinks or leaks. Kinks can occur when
the machine is moved back and forth for Your local Taylor Distributor can perform this winter
cleaning or maintenance purposes. storage service for you.
Deteriorated or cracked water lines should be Wrap detachable parts of the freezer such as beater,
replaced only by an authorized Taylor blades, drive shaft, and freezer door, and place them
distributor. in a protected dry place. Rubber trim parts and gaskets
can be protected by wrapping them with
moisture- proof paper. All parts should be thoroughly
cleaned of dried mix or lubrication which attract mice
and other vermin.

Important: Operator Checklist 26 Models 336, 338 & 339

Section 8 Troubleshooting Guide

PROBLEM PROBABLE CAUSE REMEDY PAGE

REF.
1. No product is being a. Freeze- up in mix inlet a. Call service technician to ---
dispensed with draw valve hole. adjust the mix hopper
open and the machine in temperature.
the “AUTO” mode.
b. Beater motor out on reset. b. Reset the freezer. 14
c. The beater is rotating c. Contact service technician ---
counterclockwise from the to correct rotation to
operator end. clockwise from operator
end.
d. The circuit breaker is off d. Turn the breaker on, or ---
or the fuse is blown. replace the fuse.
e. There is inadequate mix in e. Fill the mix hopper with 22
the mix hopper. mix.
f. The air orifice is not f. Install air orifice in air 21
installed. tube.
g. Air tube is installed in the g. Install the air tube in the 21
“STANDBY” position. “AUTO” position.
2. The product is too stiff. a. The viscosity needs a. Contact service ---
adjustment. technician.
b. The air orifice is not b. Install air orifice in air 21
installed. tube.
3. The product is too soft. a. Viscosity needs a. Contact service ---
adjustment. technician.
b. Not enough air space b. Allow for adequate air flow 6
around unit. (Air cooled across the condenser.
units)
c. Worn scraper blades. c. Replace regularly. 30
d. Dirty condenser (A/C) d. Clean monthly. 25
e. Mix is out of date. e. Use only fresh mix. ---
f. Loss of water. (W/C) f. Locate cause of water 26
loss and correct.
g. Loss of refrigerant. g. Call a service technician. ---
4. The mix in the mix hopper a. The temperature is out of a. Call service technician to ---
is too cold. adjustment. adjust the mix hopper
temperature.

Models 336, 338 & 339 27 Troubleshooting Guide

 PROBLEM PROBABLE CAUSE REMEDY PAGE
REF.
5. The mix in the mix hopper a. The temperature is out of a. Call service technician to ---
is too warm. adjustment. adjust the mix hopper
temperature.
b. Missing or defective mix b. Replace/install the gasket 21
hopper gasket. around the mix hopper.
c. The mix hopper cover is c. Place the cover in 22
not in position. position.
d. The mix refrigeration light d. Press mix refrigeration 22
is not lit. button.
e. The condenser is dirty. e. Clean the condenser. 25
6. The drive shaft is stuck in a. Rounded corners of drive a. Call service technician to ---
the drive coupling. shaft, coupling, or both. correct cause, and to
replace the necessary
components. Do not
lubricate the hex end of
the drive shaft.
b. Mix and lubricant collected b. Brush clean the rear shell 24
in the drive coupling. bearing area regularly.
7. The freezing cylinder walls a. The beater assembly is a. Call service technician to ---
are scored. bent. repair or replace the
beater and to correct the
cause of insufficient mix in
the freezing cylinder.
b. The front bearing is b. Install or replace the front 16
missing or worn on the bearing.
freezer door.
8. Excessive mix leakage a. Missing or worn drive a. Install or replace regularly. 15 / 30
into the rear drip pan. shaft seal on drive shaft.
b. The rear shell bearing is b. Call service technician to ---
worn. replace rear shell bearing.
9. Excessive mix leakage a. Missing or worn draw a. Install or replace regularly. 17 / 30
from door spout. valve o- rings.
b. Inadequate lubrication of b. Lubricate properly. 17
draw valve o- rings.
c. Wrong type of lubricant is c. Use the proper lubricant 15
being used (example: (example: Taylor Lube).
petroleum base lubricant).

Troubleshooting Guide 28 Models 336, 338 & 339

 PROBLEM PROBABLE CAUSE REMEDY PAGE
REF.
10. No freezer operation after a. Unit is unplugged. a. Plug into wall receptacle. ---
pressing the “AUTO”
button.
b. The circuit breaker is off b. Turn the breaker on, or ---
or the fuse is blown. replace the fuse.
c. The beater motor is out on c. Reset the freezer. 14
reset.
d. The unit has gone off on d. Allow the unit to cool and 25/ 26
high pressure cut- out. reset. Check for dirty
condenser (air cooled) or
loss of water (water
cooled).
11. Product is not feeding into a. Inadequate level of mix in a. Fill the mix hopper with 22
the freezing cylinder. the mix hopper. mix.
b. The mix inlet hole is b. The mix hopper ---
frozen up. temperature needs
adjustment. Call service
technician.
c. The air tube is installed c. Install the air tube in the 21
incorrectly. mix inlet hole, using the
end with the small hole in
the side.
d. The air orifice is not d. Install the air orifice in the 21
installed. air tube.

Models 336, 338 & 339 29 Troubleshooting Guide

Section 9 Parts Replacement Schedule

PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY

Drive Shaft Seal X

Scraper Blade X

Freezer Door Gasket X

Front Bearing X

Draw Valve O- Ring X

Pivot Pin O- Ring X

Prime Plug O- Ring X

Air Tube O- Ring X

Air Orifice O- Ring X

White Bristle Brush, 3” x 7” Inspect & Replace Minimum

if Necessary

White Bristle Brush, 1” x 2” Inspect & Replace Minimum

if Necessary

Black Bristle Brush, 1” x 2” Inspect & Replace Minimum

if Necessary

Double- Ended Brush Inspect & Replace Minimum

if Necessary

Parts Replacement Schedule 30 Models 336, 338 & 339

Section 10 Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)
to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,
will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for
a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed
below and on the reverse (if any) of this document.

Product Part Limited Warranty Period

Soft Serve Insulated shell assembly Five (5) years
Frozen Yogurt Refrigeration compressor Five (5) years
Shakes (except service valve)
Smoothies Beater motors Two (2) years
Frozen Beverage Beater drive gear Two (2) years
Batch Desserts Printed circuit boards and Two (2) years
Softech controls beginning
with serial number H8024200
Parts not otherwise listed in One (1) year
this table or excluded below

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins
ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of
purchase may be required at time of service.
2. This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are
used.
3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.
5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective parts, replacement parts, or new Products.
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers.

131122

Models 336, 338 & 339 31 Limited Warranty on Equipment

 3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.
4. External hoses, electrical power supplies, and machine grounding.
5. Parts not supplied or designated by Taylor, or damages resulting from their use.
6. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or
water supply specification of the Product; or components repaired or altered in any way so as, in the
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.
9. Any Product purchased over the Internet.
10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will
void this limited warranty.
13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or
remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.

Limited Warranty on Equipment 32 Models 336, 338 & 339

Section 11 Limited Warranty on Parts
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally
(the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service
agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions
listed below and on the reverse (if any) of this document.

Part’s Warranty Class Code or Part Limited Warranty Period

Class 103 Parts¹ Three (3) months
Class 212 Parts² Twelve (12) months
Class 512 Parts Twelve (12) months
Class 000 Parts No warranty
Taylor Part #072454 (Motor- 24VDC *C832/C842*) Four (4) years

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required
at time of service.
2. This limited warranty is valid only if the Part is installed and all required service work in connection with the
Part is performed by an authorized Taylor distributor or service agency.
3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.
4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.
6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate
Taylor Limited Warranty on freezer or grill equipment.
7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this
limited warranty.

1, 2Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.

131122

Models 336, 338 & 339 33 Limited Warranty on Parts

 LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:

1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective Parts, replacement Parts, or new Parts.
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers or carbon and grease buildup.
3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including
the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper
assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but
not limited to the platen and plate, sides of the shroud or top of the shroud.
4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or
in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or
other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials
or cleaning processes not approved for use by Taylor.
5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any
release sheets and clips for the Product’s upper platen assembly.

6. External hoses, electrical power supplies, and machine grounding.

7. Parts not supplied or designated by Taylor, or damages resulting from their use.

8. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or
water supply specification of the unit in which a part is installed; or Parts or the units in which they are
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or
normal wear or deterioration.
11. Any Part purchased over the Internet.
12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is
installed will void this limited warranty.
15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.

Limited Warranty on Parts 34 Models 336, 338 & 339

 LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.

Models 336, 338 & 339 35 Limited Warranty on Parts

 BLACK

CAPACITOR
START

LINE
BLACK
BLACK
L1 L2

COPELAND COMPRESSOR WIRING

BLUE

5
RELAY

OVERLOAD
INTERNAL

WHITE
2
1
WHT WHT

C
FIG.1

BLEED RESISTOR

BROWN
L1 T1 BLK BLK T2 L2 BLK
M
MAIN MAIN
MAIN
COMPRESSOR COMPRESSOR CONTACTOR 240K

CAPACITOR
RUN
COMPRESSOR

BLACK
(FIG. 1)
CONTACTOR
ON BLK

S
GRN/YEL C
T
OFF WHT
MIX
THERMISTOR PROBE

WHT
BLK

ON
NC
T
C
GRN/YEL C LEFT STANDBY
N0 THERMISTOR PROBE
OFF

BLK
LEFT

WHT
PUR PUR BLK

BRN
BLK
DRAW
SWITCH

BRN
NO MIX LEVEL
(OPTION)

BLACK
ON

C
BLACK INTERNAL
YELLOW INTERNAL

RED INTERNAL

ORANGE INTERNAL

BLUE INTERNAL

A
NOTE: FOR CCWLE - BLUE INTERNAL ON #1, YELLOW INTERNAL ON #6

2) MOVE BLUE INTERNAL (FROM MOTOR MAIN WINDING)

1) REMOVE BROWN JUMPER FROM BETWEEN TERMINAL #1 TO TERMINAL #5
STEPS:

MIX MIX DRAW SHK MIX 1 BRL FAN MIX 2

OFF
FROM TERMINAL #5 TO TERMINAL #1.

LEFT MIX LOW OUT PUMP PROBE

WHITE
PROBE
MAGNETEK BEATER MOTOR WIRING

DIP SWITCH SET POINT MIX LOW MIX OUT

UP = OFF
1-COMP 5
2-MIX LO CHIM

RIBBON CABLE
3-BTR 10 MIX STANDBY WASH AUTO PUMP
5-FAN 2
6-STBY DIS
7-INTERVAL
2

8-INTERVAL
5

LEFT LOGIC BOARD

3

S.S. VISCOSITY MIX STANDBY

1
6

NO SHAKE TEMP.
4

4.5 MIX DIFF.

JMPR
13 SHUNT
=2

SWITCH INTERVAL
7 8 TIME
OFF OFF 16 MIN MAX MIN MAX MIN MAX
OFF ON 14
ON OFF 11
BLACK

ON ON 5
BLACK

BLUE
CP CONTACTS ARE NOT AVAILABLE

SEE FIG.4
BLUE
USE T3 AND L3 WHEN
T3
T2

CP

T1

BEATER MOTOR
CONTACTOR

L1 T1 BLK BLK BLK T2 L2 WHT

BLK
M
GREEN/YELLOW LEFT BEATER
LEFT BEATER MOTOR STARTER

BLUE

BLUE
MOTOR STARTER LEFT BEATER
L3
L2

CP

L1

MOTOR (FIG. 2)
CP CP
LEFT BEATER
MOTOR STARTER
BRN WHT
M
SHR COMPRESSOR
(FIG. 3)
GRN/YEL
BRN WHT
M
SHR
ON GND CONDENSER FAN
MIX LEFT COMPRESSOR
BLK/WHT BEATER ENABLE RELAY
BLU C FAN RED/BLK WHT
L1 13 14
OFF BLK/WHT
PUMP
CONTROL
BTR
2) SPLICE BLUE WIRE AS SHOWN
1) DISCONNECT WIRE T7 FROM TERMINAL 3
STEPS:

BLK
T1
T8
T5

SWITCH
T4

BLK/YEL
T7

9 5
4PDT L2 1 COM
BLK/WHT
LEESON BEATER MOTOR WIRING

CABLE A O.L.

ORN
LEFT
POWER BOARD
BLK WHT
4

A B
FIG. 2

BLK/WHT BLK WHT

3 4 M
BLACK
BLACK

BLUE
BLUE
CP CONTACTS ARE NOT AVAILABLE

MAIN CONDENSER
FAN RELAY MAIN CONDENSER
USE T3 AND L3 WHEN

FAN MOTOR
T1
T2

T3

CP

BRN

BLK
(A.C. UNIT ONLY)
BEATER MOTOR

CABINET FAN MOTOR

CONTACTOR

(W.C. UNIT ONLY)

BLK WHT

ORN
M
CP

L1
L2

L3

GRN/YEL
WHT WHT

LEFT BEATER
MOTOR STARTER
ORN WHT
A1 A2
LEFT LIQUID
LINE SOLENOID VALVE
J12 OR PURPLE INTERNAL

WHT
T4 OR YELLOW INTERNAL

RED/BLK
BLK/YEL
J9 OR BLACK INTERNAL

T8 OR RED INTERNAL
T1 OR BLUE INTERNAL

LEFT SUCTION
LINE SOLENOID VALVE
WHT
NOTE: FOR CCWLE - BLUE INTERNAL ON #1,YELLOW INTERNAL ON #2

BLK/WHT

MAIN
COMPRESSOR CONTACTOR
GE/RBC BEATER MOTOR WIRING

BLK/YEL WHT
A1 A2
BRN

WHT BLK
5

NC
T
1

C
A

N0 RIGHT STANDBY
BLACK

THERMISTOR PROBE
4

BLACK

RIGHT WHT
2

PUR PUR BLK

BRN

DRAW
BLK

SWITCH

BRN
BLACK

NO MIX LEVEL
CONTACTS ARE NOT AVAILABLE

BLACK
BLUE

(OPTION)
BLUE
USE T3 AND L3 WHEN CP

CP

T1
T3
T2

A
BEATER MOTOR

MIX MIX DRAW SHK MIX 1 BRL FAN MIX 2

CONTACTOR

RIGHT MIX LOW OUT PUMP PROBE

PROBE DIP SWITCH SET POINT MIX LOW MIX OUT
UP = OFF
1-COMP 5
2-MIX LO CHIM
RIBBON CABLE

3-BTR 10 MIX STANDBY WASH AUTO PUMP

5-FAN 2

WHT
6-STBY DIS
7-INTERVAL
8-INTERVAL
CP

RIGHT LOGIC BOARD

L1
L3
L2

BLK/WHT

S.S. VISCOSITY MIX STANDBY

4.5
NO
MIX DIFF.
SHAKE TEMP.
JMPR
13 SHUNT
BRN

=2

SWITCH INTERVAL
7 8 TIME
OFF OFF 16 MIN MAX MIN MAX MIN MAX
OFF ON 14
ON OFF 11
ON ON 5

SEE FIG.4
GROUND FRAME SECURELY

L1 T1 BLK BLK BLK T2 L2 WHT

M
RIGHT BEATER GRN/YEL RIGHT BEATER
BLUE

RIGHT BEATER
BLU

MOTOR STARTER MOTOR STARTER

MOTOR (FIG. 2)
WINDING

L1

CP CP
MAIN

RIGHT BEATER
COMPRESSOR WIRING
(MODEL TL3G W/HST)

GRN/YEL MOTOR STARTER

L2

ORN//WHT WHT
10

A1 A2
BLK/YEL
12
(INTERNAL)
PROTECTOR

RIGHT LIQUID
WINDING

GND
FIG. 3

LINE SOLENOID VALVE

14

BEATER MIX
RED/WHT WHT
FAN
L1
13

BLK/WHT RIGHT SUCTION

PUMP
11

(047702-27)

LINE SOLENOID VALVE

BTR ORN/WHT ORN/WHT WHT
RELAY
START

L2 COM RED/WHT
WINDING
START

CABLE A RIGHT COMPRESSION

O.L. ENABLE RELAY
RED/WHT WHT
RIGHT 13 14
CAPACITOR

BLK/WHT
(047703)

POWER BOARD
START

WHT WHT

BLK
9 5

RIGHT COMPRESSOR
ENABLE RELAY

BRN/WHT

8
5
BRN 12
9 4
BLACK CORD 1 DOOR INTERLOCK
DOOR INTERLOCK RELAY
RELAY
BRN
BLK YEL BLK WHT
BLK CORD
INTERLOCK

13

BRN BRN BRN/WHT

95 96 95 96
24 VLT

RELAY
LOGIC BOARD SETTINGS

240V

DOOR

N. O.
DOOR
INTERLOCK
14

SWITCH
YEL
WHT HPCO
LEFT BEATER RIGHT BEATER
OVERLOAD SWITCH OVERLOAD SWITCH
FIG.4

WHT
8

EXCEPT 5.
TOWARDS FACE PLATE (OFF)
SELECTION. ALL DIP SWITCHES
DIP SWITCH FOR FUNCTION
4.5 SHOWN
SELECTOR SHUNT DEFAULT
TEMPERATURE DIFFERENTIAL

FACE PLATE

Taylor Company
Model 336
069269-27
c 2014 Carrier Commercial Refrigeration, Inc. 07/14
 L1 L2 L3

BLK BLK

BLK BLK

BLK T3 L3 BLK

MAIN
COMPRESSOR CONTACTOR

L1 T1 BLK BLK T2 L2 BLK

M
WINDING

L1
MAIN MAIN MAIN 240K
MAIN COMPRESSOR COMPRESSOR COMPRESSOR CONTACTOR
COMPRESSOR WIRING

CONTACTOR
(MODEL TL3G W/HST)

WHT BLK

L2
GRN/YEL C
T

10
12
(INTERNAL)
PROTECTOR

MIX
WINDING
FIG.1

BLK
THERMISTOR PROBE

14

BLK
13 BLK

11

(047702-27)
NC
T

RELAY
START
C
GRN/YEL C
WINDING

N0 LEFT STANDBY
START

BLK
THERMISTOR PROBE
LEFT
CAPACITOR

WHT
BRN
PUR PUR BLK

BLK
(047703)

DRAW
START

SWITCH

NO MIX LEVEL BRN

(OPTION)

C
MIX MIX DRAW SHK A MIX 1 BRL FAN MIX 2
LEFT MIX LOW OUT PUMP PROBE

WHT
PROBE DIP SWITCH SET POINT MIX LOW MIX OUT
UP = OFF

RIBBON CABLE
1-COMP 5
2-MIX LO CHIM
3-BTR 10 MIX STANDBY WASH AUTO PUMP
5-FAN 2
6-STBY DIS
7-INTERVAL
8-INTERVAL
LEFT LOGIC BOARD
S.S. VISCOSITY MIX STANDBY
4.5
NO
MIX DIFF.
SHAKE TEMP.
JMPR
13 SHUNT
=2

SWITCH INTERVAL
7 8 TIME
OFF OFF 16 MIN MAX MIN MAX MIN MAX
OFF ON 14
ON OFF 11
ON ON 5

SEE FIG.3
L1 T1 BLK BLK BLK T2 L2 BLK
M LEFT
CAP

RED 50 HZ

GRN/YEL
WHT COM

BLK 60 HZ

LEFT BEATER BEATER MOTOR LEFT BEATER

BLK BLK
MOTOR STARTER MOTOR STARTER
BRN
BRN

BLK T3 L3 BLK
BLK
LEFT BEATER
6

SHR FAN MOTOR

208/240
GE MOTOR SCHEMATIC

MOTOR STARTER
EXTRA

BRN
MAIN

WHT
M
GRN/YEL
5

SHR COMPRESSOR
BRN (FIG. 1)
WHT
FIG. 2

THERMAL

GRN/YEL M
50/60 HZ
O.L.

GRN/YEL LEFT COMPRESSOR

ENABLE RELAY WHT
2C

13 14
RED/BLK
MAIN
GND
MIX
1

BEATER
START

BLK BLK/YEL
BLK C FAN 9 5
BLK/WHT L1
PUMP
3

CONTROL
SWITCH BTR

WHT
4PDT L2 1 COM
CABLE A O.L. BLK WHT
BLK/WHT

A B
LEFT
POWER BOARD
BLK/WHT BLK/WHT BLK BLK WHT WHT
3 4 M
MAIN CONDENSER GRN/YEL
FAN RELAY
MAIN CONDENSER
(A.C. UNIT ONLY)

ORN
FAN MOTOR

BRN

BLK
(A.C. UNIT ONLY)
CABINET FAN MOTOR SEE FIG 2
(W.C. UNIT ONLY)
BLK WHT
GRN/YEL
M

WHT WHT

ORN WHT
A1 A2
LEFT BEATER
MOTOR STARTER
BLK

RED/BLK WHT
BLK/YEL
LOGIC BOARD SETTINGS

BRN
LEFT LIQUID
LINE SOLENOID VALVE
ORN WHT

LEFT SUCTION
FIG.3

LINE SOLENOID VALVE

BLK/YEL WHT
8

A1 A2
MAIN
COMPRESSOR CONTACTOR

WHT BLK
TOWARDS FACE PLATE
ALL DIP SWITCHES
FUNCTION SELECTING
DIP SWITCH FOR

NC
4.5 SHOWN
SELECTOR SHUNT DEFAULT
TEMPERATURE DIFFERENTIAL

T
FACE PLATE

C
N0 RIGHT STANDBY
BLK/WHT

BLK

THERMISTOR PROBE
RIGHT
BLK

WHT
BRN

PUR PUR DRAW BLK

SWITCH

NO MIX LEVEL BRN

(OPTION)

BLK
MIX MIX DRAW SHK A MIX 1 BRL FAN MIX 2
RIGHT MIX LOW OUT PUMP PROBE
BRN

PROBE DIP SWITCH SET POINT MIX LOW MIX OUT

UP = OFF
1-COMP 5
2-MIX LO CHIM
RIBBON CABLE

3-BTR 10 MIX STANDBY WASH AUTO PUMP

5-FAN 2
6-STBY DIS
7-INTERVAL
8-INTERVAL

RIGHT LOGIC BOARD

S.S. VISCOSITY MIX STANDBY
NO SHAKE TEMP.
4.5 MIX DIFF.
JMPR
13 SHUNT
=2

SWITCH INTERVAL
7 8 TIME
OFF OFF 16 MIN MAX MIN MAX MIN MAX
OFF ON 14
ON OFF 11
ON ON 5

SEE FIG.3
L1 T1 BLK BLK BLK T2 L2 BLK
M
GRN/YEL RIGHT
RIGHT BEATER RIGHT BEATER
BEATER MOTOR
MOTOR STARTER MOTOR STARTER

BLK T3 L3 BLK
GROUND FRAME SECURELY

RIGHT BEATER
RIGHT BEATER MOTOR STARTER
UNDER PRIMARY SINGLE PHASING CONDITIONS
COMPRESSOR AND BEATER MOTORS PROTECTED

GRN/YEL MOTOR STARTER

ORN/WHT WHT
BLK/YEL

A1 A2

RIGHT LIQUID
GND LINE SOLENOID VALVE
BEATER MIX RED/WHT WHT
FAN
BLK/WHITE L1
PUMP RIGHT SUCTION
LINE SOLENOID VALVE
BTR ORN/WHT WHT
L2 1 COM
CABLE A O.L.
BLACK
CORD

RIGHT COMPRESSOR
RIGHT ENABLE RELAY
POWER BOARD RED/WHT WHT
13 14

WHT WHT

BLK BLK/YEL
9 5
BLK

DOOR INTERLOCK
RELAY
5
DOOR INTERLOCK
BRN BRN/WHT RELAY
9 8
1 12

4
BRN

BLACK BRN BRN BRN/WHT

95 96 95 96
CORD

HPCO
N. O. LEFT BEATER RIGHT BEATER
DOOR OVERLOAD SWITCH
INTERLOCK
OVERLOAD SWITCH
SWITCH

BLK YEL BLK

INTERLOCK

13
24 VLT

RELAY

DOOR
14

YEL
WHT

WHT

Taylor Company
Model 336
069269-33
c 2014 Carrier Commercial Refrigeration, Inc. 07/14
 L1 L2

J12 OR PURPLE INTERNAL

BLACK BLACK
T4 OR YELLOW INTERNAL

J9 OR BLACK INTERNAL

T8 OR RED INTERNAL
T1 OR BLUE INTERNAL

NOTE: FOR CCWLE - BLUE INTERNAL ON #1,YELLOW INTERNAL ON #2

L1 T1 BLACK BLACK T2 L2 BLACK
M

GE/RBC BEATER MOTOR WIRING

MAIN MAIN MAIN 240K
COMPRESSOR COMPRESSOR COMPRESSOR CONTACTOR
CONTACTOR (FIG. 1)
WHITE BLACK
GRN/YEL C
T

MIX

BLACK
THERMISTOR PROBE

BLACK
5

NC
T
C
1

GRN/YEL C
N0 LEFT STANDBY

BLACK
A

THERMISTOR PROBE

BROWN
LEFT

BLACK

WHITE
BLACK PURPLE DRAW BLACK
4

BLACK
SWITCH
2

NO MIX LEVEL BROWN

(OPTION)
BLACK
CONTACTS ARE NOT AVAILABLE

BLACK

C
BLUE

A
BLUE

MIX MIX DRAW SHK MIX 1 BRL FAN MIX 2

USE T3 AND L3 WHEN CP

LEFT MIX

WHITE
LOW OUT PUMP PROBE
PROBE SET POINT MIX LOW MIX OUT
CP

T1
T3
T2

RIBBON CABLE
BEATER MOTOR
CONTACTOR

MIX STANDBY WASH AUTO PUMP

LEFT LOGIC BOARD

S.S. VISCOSITY MIX STANDBY
SHAKE TEMP.
CP

L1
L3
L2

MIN MAX MIN MAX MIN MAX

L1 T1 BLACK BLACK BLACK T2 L2 BLACK

M
GREEN/YELLOW LEFT BEATER
LEFT BEATER
MOTOR STARTER

BLUE

BLUE
MOTOR STARTER LEFT BEATER
MOTOR (FIG. 2)
NOTE: FOR CCWLE - BLUE INTERNAL ON #1, YELLOW INTERNAL ON #6

2) MOVE BLUE INTERNAL (FROM MOTOR MAIN WINDING)

1) REMOVE BROWN JUMPER FROM BETWEEN TERMINAL #1 TO TERMINAL #5
STEPS:
FROM TERMINAL #5 TO TERMINAL #1.

CP CP
MAGNETEK BEATER MOTOR WIRING

LEFT BEATER
MOTOR STARTER
BLACK INTERNAL
YELLOW INTERNAL

RED INTERNAL

ORANGE INTERNAL

BLUE INTERNAL

WHITE/BLACK WHITE
M
SHR COMPRESSOR
GRN/YEL (FIG. 3)
WHITE/BLACK WHITE
M
2
5

SHR
3

GND CONDENSER FAN

BEATER MIX BROWN BROWN
1
6

BLACK C FAN BLACK WHITE

BLUE L1 M
PUMP
BLACK

BROWN

BLACK
CONTROL
BLACK

MAIN CONDENSER
BLUE

BTR
CP CONTACTS ARE NOT AVAILABLE

SWITCH FAN MOTOR

BLUE

4PDT L2 1 COM (A.C. UNIT ONLY)

USE T3 AND L3 WHEN
T3
T2

CP

T1

ORANGE
BEATER MOTOR

CABLE A O.L. BLACK WHITE

CONTACTOR

M
LEFT
CABINET FAN MOTOR
POWER BOARD
(W.C. UNIT ONLY)
L3
L2

CP

L1

WHITE WHITE

BROWN ORANGE WHITE

A1 A2
LEFT BEATER
BLUE

MOTOR STARTER
RED/BLACK

BLACK CORD BLACK CORD

LEFT LIQUID
LINE SOLENOID VALVE
BLACK CORD BLACK CORD

LEFT SUCTION
T1
T8
T5
T4

T7

LINE SOLENOID VALVE

2) SPLICE BLUE WIRE AS SHOWN
1) DISCONNECT WIRE T7 FROM TERMINAL 3
STEPS:

WHITE
A1 A2
FIG. 2

LEESON BEATER MOTOR WIRING

MAIN
COMPRESSOR CONTACTOR
BLACK

WHITE BLACK
4

NC
T
C
N0 RIGHT STANDBY
BLACK

BLACK
BLACK

BLUE
BLUE

THERMISTOR PROBE
CP CONTACTS ARE NOT AVAILABLE

BLACK

BROWN

RIGHT
WHITE

BLACK PURPLE BLACK

USE T3 AND L3 WHEN

DRAW
T1
T2

T3

CP

BEATER MOTOR

SWITCH
CONTACTOR

NO MIX LEVEL BROWN

(OPTION)

BLACK
CP

L1
L2

L3

BLUE

MIX MIX DRAW SHK A MIX 1 BRL FAN MIX 2

BROWN

RIGHT MIX LOW OUT PUMP PROBE

PROBE SET POINT MIX LOW MIX OUT
RIBBON CABLE

MIX STANDBY WASH AUTO PUMP

RIGHT LOGIC BOARD

S.S. VISCOSITY MIX STANDBY
SHAKE TEMP.

MIN MAX MIN MAX MIN MAX

L1 T1 BLACK BLACK BLACK T2 L2 BLACK

M
RIGHT BEATER GREEN/YELLOW RIGHT BEATER
BLUE

BLUE

MOTOR STARTER RIGHT BEATER MOTOR STARTER

MOTOR (FIG. 2)
CP CP
GROUND FRAME SECURELY

RIGHT BEATER
MOTOR STARTER
GRN/YEL
RED/BLACK

ORANGE/WHITE WHITE
UNDER PRIMARY SINGLE PHASING CONDITIONS
COMPRESSOR AND BEATER MOTORS PROTECTED

A1 A2
RIGHT BEATER
GND MOTOR STARTER
BEATER MIX BLACK CORD BLACK CORD
FAN
BLUE L1 RIGHT LIQUID
PUMP LINE SOLENOID VALVE
BTR BLACK CORD BLACK CORD
L2 1 COM RIGHT SUCTION
CABLE A O.L. LINE SOLENOID VALVE
BLACK
CORD

RIGHT
POWER BOARD
WHITE WHITE

BLACK BROWN BROWN

CORD 95 96 95 96

HPCO
LEFT BEATER RIGHT BEATER
OVERLOAD SWITCH OVERLOAD SWITCH

BLACK
CAPACITOR
START

LINE
BLACK
WINDING

L1
MAIN

BLACK
BLUE

5
RELAY
COMPRESSOR WIRING
FIG. 3
(MODEL TL3G W/HST)

OVERLOAD
INTERNAL
L2

WHITE
10

COMPRESSOR WIRING
(INTERNAL)

12

FIG.1
PROTECTOR
WINDING

2
1
14

C
BLEED RESISTOR
13

BROWN
11

(047702-27)
RELAY
START

338
CAPACITOR
RUN

BLACK
WINDING
START

051624-27
CAPACITOR
(047703)

START

11/19/13
 L1 L2 L3

BLACK BLACK

BLACK BLACK

BLACK T3 L3 BLACK

MAIN
COMPRESSOR CONTACTOR

L1 T1 BLACK BLACK T2 L2 BLACK

M
MAIN MAIN MAIN 240K
COMPRESSOR COMPRESSOR COMPRESSOR CONTACTOR
CONTACTOR
WHITE BLACK
GRN/YEL C
T

MIX

BLACK
THERMISTOR PROBE
BLACK

BLACK
NC
T
C
GRN/YEL C
N0 LEFT STANDBY

BLACK
THERMISTOR PROBE

BROWN
LEFT

BLACK

WHITE
BLACK PURPLE DRAW BLACK
SWITCH

NO MIX LEVEL BROWN

(OPTION)

C
MIX MIX DRAW SHK A MIX 1 BRL FAN MIX 2
LEFT MIX LOW OUT PUMP PROBE
WHITE

PROBE SET POINT MIX LOW MIX OUT

RIBBON CABLE
MIX STANDBY WASH AUTO PUMP

LEFT LOGIC BOARD

S.S. VISCOSITY MIX STANDBY
SHAKE TEMP.

MIN MAX MIN MAX MIN MAX

L1 T1 BLACK BLACK BLACK T2 L2 BLACK

M
GREEN/YELLOW LEFT LEFT BEATER
LEFT BEATER
BEATER MOTOR MOTOR STARTER
MOTOR STARTER
BLACK T3 L3 BLACK

LEFT BEATER LEFT BEATER

MOTOR STARTER MOTOR STARTER
WHITE/BLACK WHITE
M
SHR COMPRESSOR
GRN/YEL (FIG. 3)
WHITE/BLACK WHITE
M
GND SHR
BEATER MIX CONDENSER FAN
BLACK C FAN BLACK WHITE
BLUE L1 M
PUMP

BROWN

BLACK
CONTROL MAIN CONDENSER
SWITCH BTR FAN MOTOR
4PDT L2 1 COM (A.C. UNIT ONLY)
ORANGE

CABLE A O.L. BLACK WHITE

M
BLUE

LEFT
CABINET FAN MOTOR
POWER BOARD
(W.C. UNIT ONLY)
WHITE WHITE

BROWN ORANGE WHITE

A1 A2
LEFT BEATER
BLACK

MOTOR STARTER
RED/BLACK

BLACK CORD BLACK CORD

LEFT LIQUID
LINE SOLENOID VALVE
BLACK CORD BLACK CORD

LEFT SUCTION
LINE SOLENOID VALVE
WHITE
A1 A2
MAIN
COMPRESSOR CONTACTOR

WHITE BLACK
NC
T
C
N0 RIGHT STANDBY
BLACK
BLUE

THERMISTOR PROBE
BLACK

BROWN

RIGHT
WHITE

BLACK PURPLE DRAW BLACK

SWITCH

NO MIX LEVEL BROWN

(OPTION)
BLACK

MIX MIX DRAW SHK A MIX 1 BRL FAN MIX 2

BROWN

RIGHT MIX LOW OUT PUMP PROBE

PROBE SET POINT MIX LOW MIX OUT
RIBBON CABLE

MIX STANDBY WASH AUTO PUMP

RIGHT LOGIC BOARD

S.S. VISCOSITY MIX STANDBY
SHAKE TEMP.

MIN MAX MIN MAX MIN MAX

L1 T1 BLACK BLACK BLACK T2 L2 BLACK

M
GREEN/YELLOW RIGHT
RIGHT BEATER RIGHT BEATER
BEATER MOTOR MOTOR STARTER
MOTOR STARTER
BLACK T3 L3 BLACK

RIGHT BEATER
MOTOR STARTER
GRN/YEL
RED/BLACK

ORANGE/WHITE WHITE
A1 A2
RIGHT BEATER
GND MOTOR STARTER
BEATER MIX BLACK CORD BLACK CORD
FAN
BLUE L1 RIGHT LIQUID
PUMP LINE SOLENOID VALVE
BTR BLACK CORD BLACK CORD
L2 1 COM RIGHT SUCTION
CABLE A O.L. LINE SOLENOID VALVE
BLACK
CORD

RIGHT
POWER BOARD
WHITE WHITE

BLACK BROWN BROWN

CORD 95 96 95 96

HPCO
LEFT BEATER RIGHT BEATER
OVERLOAD SWITCH OVERLOAD SWITCH

START
RELAY
(047702-27)

L1
11 START
10 CAPACITOR
(047703)

12 13
14
GROUND FRAME SECURELY
COMPRESSOR AND BEATER MOTORS PROTECTED
UNDER PRIMARY SINGLE PHASING CONDITIONS
L2

MAIN WINDING START

WINDING PROTECTOR
(INTERNAL)
WINDING
338
COMPRESSOR WIRING
(MODEL TL3G W/HST)
051624-33
FIG. 3 11/19/13
 BLACK/WHITE WHITE BLACK
BLUE
BLACK BLACK 95 96 BLACK/WHITE

42002

7
5-FAN 2
3-BTR 5

ON
ON
MIX

4-BTR 10
BLACK

OFF
OFF
LOW

TAYLOR CO.

1-COMP 5
STRIPE

UP = OFF

2-COMP 10

6-STBY DIS
7-INTERVAL
8-INTERVAL
DIP SWITCH
BLK/WHT
HIGH PRESS. BEATER MOTOR

ON
ON
BLACK

OFF

OFF
CUTOUT OVERLOAD SWITCH

13
L2
L1

MIX
A1
CP

OUT
NO MODEL 774 ONLY MODEL 8754 ONLY BLACK/YELLOW

5
BLACK

11
14
16
TIME
C

SWITCH INTERVAL
BROWN A A

MIX
NC

BTR.

DRAW
14
T2
T1

A2
CP

MIN
RELAY
DRAW SWITCH BLACK

ORANGE

SWITCH

SHK
HEATER

PUMP

S.S.VISCOSITY

MAX
SHAKE TEMP.
A BLACK

STANDBY
SET POINT
OL
L1 L2

1
B
GRN/YEL

BLK

MIN
LA

BROWN
BLACK
C

MIX
3

WASH
A

BLACK
BLUE

BLACK

MIX LOW
2
3

MAX
240K
LEFT SIDE

BTR.
K MTR.

BLACK/WHITE
BLACK
BLACK

4
WHITE WHITE BLACK

BLACK/YELLOW

MIN
MOTOR

AUTO
RESET SWITCH

MIX OUT
MIX 1
L2

LEFT SIDE
SOFTECH CONTROL
LEFT POWER/RELAY BOARD

MIX PUMP MOTOR

M

THERMOSTAT
RELAY PUMP

STANDBY
WHITE BLACK MIX HOPPER

MAX
BRL
RED
TEMP. GREEN/YELLOW

PROBE
A

PUMP
BLACK
CABINET FAN
STBY TEMP. WHITE BLACK

YELLOW
4

B
BLACK

HI-LIMIT
L1

FAN MIX 2
BLACK

FAN RELAY
WHITE

THERMOSTAT
(WATER COOLED ONLY)
COM BTR PUMPFAN MIX
BROWN

MFG DATE
BTR GND
13
L3
L2
L1

A1

BLACK

MOTOR
(AIR COOLED ONLY)

MIX PUMP
BROWN
14
T3
T2
T1

A2
RELAY

GRN/YEL
COMP.

PURPLE

ORANGE

SYRUP
M

HEATER
BLACK

ORANGE
WHITE
BLACK

BLACK

42002

3-BTR 5

5-FAN 2

7
BROWN

MIX

4-BTR 10

ON
ON
OFF
1-COMP 5

OFF
LOW

UP = OFF

2-COMP 10
FAN

TAYLOR CO.

6-STBY DIS
7-INTERVAL
DIP SWITCH

8-INTERVAL
BROWN
START RELAY

ON

ON
BLACK

OFF

OFF
RED/BLACK STRIPE

(AIR COOLED ONLY)

MIX
COMP

OUT
BLACK
NO

5
BLACK

14
11
16
BROWN
CONDENSER BLOWER
(ALSO SEE FIG.2)

SWITCH INTERVAL
TIME
C

WHITE
10 14
11 13
BROWN WHITE

MIX REF. SYSTEM

MIX
NC

WHITE

DRAW
WHITE/BLACK
WHITE

START CAP

MIN
DRAW SWITCH BLACK/WHITE

SHK
(DANFOSS TL3G COMPR.)

WHITE

PUMP
COMP
B

SHAKE TEMP.

MAX
S.S.VISCOSITY
STANDBY
SET POINT
GREEN/YELLOW

MIN
MIX
B

WASH
MIX LOW

MAX
WHITE

RIGHT SIDE
AUTO

MIN
MIX OUT
MIX 1

SOFTECH CONTROL
4PDT

WHITE
WHITE BLACK

STANDBY
POWER

WHITE

MAX
BRL
SWITCH

PROBE

PUMP
STBY TEMP.
BLACK BLACK 95 96 BLUE/WHITE BLUE/WHITE

FAN MIX 2
PURPLE
WHITE BLACK

PURPLE
HIGH PRESS. BEATER MOTOR
BLUE

CUTOUT OVERLOAD SWITCH

MFG DATE
BLACK
BLACK
B B
BLACK
13
L2
L1

A1
CP

PURPLE
BLACK
BTR.
RELAY

14
T2
T1

A2
CP

PURPLE/WHITE
OL
BLUE/WHITE

MODEL 8754 ONLY BLACK

L1 L2

GRN/YEL
BLACK
BLUE

GRN/YEL
BLUE

1
PURPLE WHITE BLACK
L2

ORANGE/WHITE

BROWN
RIGHT POWER/RELAY BOARD
BTR.
RIGHT SIDE

MTR.

2
LEFT
BLACK
ORANGE

MIX LOW PROBE

4
RESET SWITCH
BLACK
BLACK

MIX PUMP MOTOR

13
L3
L2
L1

A1

GRN/YEL

MOTOR
L1

BLK/WHT
NOTE:

RELAY PUMP
14
RELAY

T3
T2
T1

A2

RED
COM BTR PUMPFAN MIX
SET JUMPERS TO
COMP.

BTR GND
WHITE

1/3 AND 2/4

BLACK
WHITE

YELLOW

BLACK
ORANGE
GRN/YEL

PURPLE/WHITE
WHITE
WHITE
BLACK
COMP

MOTOR
MIX PUMP
BLACK
RIGHT
MIX LOW PROBE

PURPLE

ORANGE

BLACK
RED/BLACK STRIPE

c 2014 Carrier Commercial Refrigeration, Inc.

YELLOW BLACK
WHITE
YELLOW

WHITE
GROUND FRAME SECURELY

GRN/YEL
NOTE:
START RELAY
1. STATIC ELECTRICITY MAY CAUSE DAMAGE
BLACK (047702-27) TO SOLID STATE COMPONENTS. ELIMINATE
STATIC ELECTRICITY BY TOUCHING GROUNDED
PURPLE
UNIT BEFORE HANDLING SOLID STATE COM-
START CAPACITOR
(047703)
PONENTS.
L1 11
WHITE 2. RED WIRE ON RIBBON CABLES MUST BE CON-

5
6

A
10

MAGNETEK BEATER MOTOR WIRING

NECTED TO PIN 1 AT EACH END.
BLACK INTERNAL OVERLOAD
STEPS: LEESON BEATER MOTOR WIRING
INTERNAL OVERLOAD

3
1
2

B
13
1) REMOVE BROWN JUMPER FROM BETWEEN TERMINAL #1 TO TERMINAL #5 STEPS:
12
WHITE WHITE 2) MOVE BLUE INTERNAL (FROM MOTOR MAIN WINDING) 1) DISCONNECT WIRE T7 FROM TERMINAL 3
C 14
C FROM TERMINAL #5 TO TERMINAL #1.
LINE 2) SPLICE BLUE WIRE AS SHOWN
LINE NOTE: FOR CCWLE - BLUE INTERNAL ON #1, YELLOW INTERNAL ON #6
RELAY BEATER MOTOR
RELAY BLUE INTERNAL BEATER MOTOR
T8 CONTACTOR
BROWN L2 CONTACTOR
BROWN 5 2 S 1 BLACK
5 2 S ORANGE INTERNAL 1 T1 T1 L1
BLACK

GRN/YEL
T1 L1
6
2 BLUE
EQUIPMENT EQUIPMENT BLUE
4 GROUND 4 1 2
GROUND 1
START WINDING 3
BLACK BLACK MAIN WINDING
R BLUE
R RED INTERNAL 4 CP CP
BLUE
RUN CAPACITOR
CP CP
RUN CAPACITOR WINDING PROTECTOR 3
MIX LOW MIX LOW START CAPACITOR START CAPACITOR T7 T3 L3
BLEED RESISTOR BLEED RESISTOR (INTERNAL)
LEFT RIGHT 5 T3 L3 USE T3 AND L3 WHEN
BRISTOL SCHEMATIC WIRING DIAGRAM - CSR TECUMSEH SCHEMATIC WIRING DIAGRAM - CSR
ALTERNATE USE T3 AND L3 WHEN CP CONTACTS ARE NOT AVAILABLE
BLACK NUMBER LOCATION
COMPRESSOR WIRING CP CONTACTS ARE NOT AVAILABLE
(MODEL TL3G W/HST) 4 BLACK
T4 T2 L2
5 1 6 YELLOW INTERNAL 6 BLACK
T2 L2 T5
FIG. 3 FIG. 4 BLACK INTERNAL
4 2
FIG. 2

07/14
051459-27
Model 339
Taylor Company
 RIGHT SIDE
LEFT SIDE

ENCLOSURE(S)
ENCLOSURE(S)

CONTROL
CONTROL
L1 L2 L3 N L1 L2 L3 N

GREEN/YELLOW
POWER
GREEN/YELLOW GREEN/YELLOW

BLACK
BLACK
BLACK

BLACK
BLACK
BLACK
WHITE

WHITE
SWITCH
4PDT
WHITE
BLACK BLUE

WHITE
GRN/YEL

BLACK
BLACK
BLACK
WHITE
BLACK
BLACK
BLACK

BLACK
BLACK
BLACK

GRN/YEL
BTR. BLACK COMP. COMP.
RELAY RELAY RELAY GRN/YEL
BLACK

WHITE
L1 T1 L1 T1 L1 T1

L2 T2 BLACK L2 T2 L2 T2
BTR.
COMP COMP
MTR.
L3 T3 L3 T3 L3 T3

BLACK/WHITE
13 14
WHITE

13 14 13 14
WHITE

BLACK
BLACK
BLACK
A1 A2 A1 A2 A1 A2

BLUE/WHITE
ORANGE BTR. BLACK
RELAY
BLACK
L1 T1

L2 T2
WHITE BLACK BTR.
MTR.
L3 T3
96 BLACK/WHITE

13 14 GRN/YEL
OVERLOAD SWITCH

L2 L1
GND
BEATER MOTOR

GRN/YEL
A1 A2
GRN/YEL STRIPE
BLACK
BLACK
LEFT POWER/RELAY BOARD

ORANGE
RED/BLACK STRIPE

COMPRESSOR AND BEATER MOTOR PROTECTED

95

WHITE
A

GROUND FRAME SECURELY

UNDER PRIMARY SINGLE PHASING CONDITIONS
BLUE/WHITE
BTR

96 BLUE/WHITE
HIGH PRESS.

L2 L1
A
CUTOUT

GND
OVERLOAD SWITCH
WHITE

GRN/YEL
BEATER MOTOR

GREEN/YELLOW STRIPE
RIGHT POWER/RELAY BOARD

BLACK
BLACK
BLACK

WHITE
RED/BLACK STRIPE
BLACK/WHITE

OL

95

COM BTR PUMPFAN MIX

BTR
BLK/WHT
GRN/YEL

WHITE
WHITE

HIGH PRESS.
CUTOUT

ORANGE
B

MIX REF. SYSTEM

(DANFOSS TL3G COMPR.)
BLACK/YELLOW (ALSO SEE FIG.2)
BROWN

BLACK

BLACK BROWN WHITE

M
OL

FAN
10 14
WHT
BLK

START RELAY 11 13 COMP COM BTR PUMPFAN MIX

BLU/WHT

GRN/YEL START CAP

BLACK BLACK 24VAC
M ORANGE
YEL
YEL

BLK/WHT

CABINET FAN GRN/YEL

BLU/WHT

(WATER COOLED ONLY)

BLACK BLACK ORANGE/WHITE
CORD RED WHT CORD
M
BLACK/WHITE
BLK/WHT

CONDENSER BLOWER
3 4
(AIR COOLED ONLY) MIX PUMP MOTOR
BLACK WHITE GRN/YEL
BLACK/YELLOW

SEE FIG 1 RESET SWITCH

A B
BLACK
1 3 PURPLE
FAN RELAY
MODEL 8754 ONLY

(AIR COOLED ONLY) YELLOW

M
ORANGE
RED
MIX PUMP MOTOR 3
GRN/YEL MIX PUMP
RESET SWITCH
WHT

BROWN MOTOR
2 4
BLACK
1 3 PURPLE
WHITE
MODEL 774 ONLY MODEL 8754 ONLY

YELLOW RELAY PUMP

M
BLK

ORANGE MOTOR
INTERLOCK

RED
SWITCH
DOOR
N. O.

3
PUR/WHT

MIX PUMP
BROWN
2 4 MOTOR
13

14

WHITE/BLACK
8

RELAY PUMP
12

GE MOTOR SCHEMATIC

MOTOR
4

3
START
5

50/60 HZ

MAIN
9

FIG. 1
2C
4

2
1

THERMAL
O.L.

BLK WHITE
208/240
MIX HOPPER

BLK/WHT HEATER THERMOSTAT HI-LIMIT BROWN

EXTRA

SYRUP
MAIN
BLACK

STRIPE SWITCH THERMOSTAT HEATER BLACK

TEMP.

BRN
BRN
RED 50 HZ

BLK 60 HZ

WHT COM
BLACK

BLACK
DRAW SWITCH

CAP
240K

DRAW SWITCH
BLACK

BLACK
START WINDING
START CAPACITOR

C
WHITE
C

STBY TEMP.

STBY TEMP.
WHITE
NO

NC
NC
NO
(047703)

B
PURPLE

PURPLE
BROWN

BROWN
BLACK

BLACK
WHITE

WHITE

WHITE
START RELAY

WINDING PROTECTOR
(047702-27)

COMPRESSOR WIRING
(INTERNAL)

(MODEL TL3G W/HST)

FIG. 2
11

MIX MIX DRAW SHK MIX 1 BRL FAN MIX 2 MIX MIX DRAW SHK MIX 1 BRL FAN MIX 2
PUMP PROBE LOW OUT PUMP PROBE
13

LOW OUT
SOFTECH CONTROL SOFTECH CONTROL
SET POINT MIX LOW MIX OUT SET POINT MIX LOW MIX OUT
TAYLOR CO. TAYLOR CO.
14

42002 42002

DIP SWITCH
12

UP = OFF DIP SWITCH

MIX WASH MIX STANDBY AUTO
10

STANDBY AUTO PUMP WASH PUMP

UP = OFF
1-COMP 5
2-COMP 10 1-COMP 5
2-COMP 10
3-BTR 5
3-BTR 5
4-BTR 10 4-BTR 10
5-FAN 2 5-FAN 2
6-STBY DIS 6-STBY DIS

Model 339
7-INTERVAL 7-INTERVAL
8-INTERVAL 8-INTERVAL

SWITCH INTERVAL SHAKE TEMP. SWITCH INTERVAL SHAKE TEMP.

7 8 TIME S.S.VISCOSITY MIX STANDBY 7 8 TIME

046585-62
S.S.VISCOSITY MIX STANDBY
MAIN WINDING

OFF 16
L2

OFF
L1

OFF OFF 16
OFF ON 14 MFG DATE OFF ON 14
ON OFF ON OFF 11
11
ON ON ON ON 5 MFG DATE
5

11/20/13
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX