SFP10-SR Specifications
DATA SHEET
MODULETEK: SFP10-SR
10Gb/s SFP+ Short Wavelength (850nm) Transceiver
SFP10-SR Overview
ModuleTek’s SFP10-SR SFP optical transceivers are based on 10G Ethernet IEEE 802.3ae standard
and SFF-8431 standard, providing a fast and reliable interface for 10G Ethernet applications. The
product implements digital diagnostics via a 2-wire serial bus ,compliant with the SFF-8472 standard.
Product Features
• Supports from 9.83 Gb/s to 11.3 Gb/s bit rates
• Compliant with IEEE 802.3ae 10GBASE-SR/SW
• Compliant with SFF-8431
• Hot-pluggable SFP+ footprint
• 850nm VCSEL laser transmitter
• Duplex LC connector
• Built-in digital diagnostic functions
• Up to 300m on OM3 MMF
• Low power consumption (Module work consumption <1W)
• Single power supply 3.3V
• RoHS Compliant
• Class 1 laser product complies with EN 60825-1
• Operating temperature range:0◦ C to 70◦ C
Applications
• 10GBASE-SR/SW
Ethernet
• 10G Fibre Channel
• 10G CPRI
SFP10-SR Specifications
ModuleTek Limited www.moduletek.com 1
Ordering Information
Operating
Part Number Description temperature range Color on Clasp
10GBASE-SR SFP+ 850nm LC
SFP10-SR Connectors 300m on MMF, 0◦ C to 70◦ C black
with DOM function.
For More Information:
ModuleTek Limited
Web: www.moduletek.com
Email:
[email protected]General Specifications
Parameter Symbol Min Typ Max Unit Remarks
Data Rate DR 9.83 10.3125 11.3 Gb/s 1
Bit Error Rate BER 10−12
Operating Temperature TC 0 70 ◦ C 2
Storage Temperature -40 85 ◦ C 3
TSTO
Supply Current 180 220 mA 4
ICC
Input Voltage VCC 3.14 3.3 3.46 V
Maximum Voltage -0.5 4 V 4
VMAX
Notes:
1. IEEE 802.3ae
2. Case temperature
3. Ambient temperature
4. For electrical power interface
Link Distances
Modal Bandwidth Distance
Data Rate Fiber Type @850nm (MHz-km) Range (m)
9.83–11.3 Gb/s 62.5/125umMMF 160 26
9.83–11.3 Gb/s 62.5/125umMMF 200 33
9.83–11.3 Gb/s 50/125umMMF 400 66
9.83–11.3 Gb/s 50/125umMMF 500 82
ModuleTek Limited www.moduletek.com 2
SFP10-SR Specifications
9.83–11.3 Gb/s 50/125umMMF 2000 300
Optical – Characteristics – Transmitter
VCC=3.14V to 3.46V, TC=0◦ C to 70◦ C
Parameter Symbol Min Typ Max Unit Remarks
Output Optical Power PTX -7 -1 dBm 1
Optical Center Wavelength λC 840 860 nm
Optical Modulation Amplitude OMA -1.5 dBm 2
Extinction Ratio ER 3 5.5 dB
Spectral Width (RMS) Δλ 0.45 nm
Relative Intensity Noise RIN -128 dB/Hz
Transmitter Dispersion Penalty TDP 3.9 dB
Transmitter Jitter 3
Launch Power of OFF Transmitter -30 dBm 1
POUT_OFF
Notes:
1.Average
2. IEEE 802.3ae
3.According to IEEE 802.3ae requirement
Optical – Characteristics – Receiver
VCC=3.14V to 3.46V, TC=0◦ C to 70◦ C
Parameter Symbol Min Typ Max Unit Remarks
Optical Center Wavelength λC 840 860 nm
RX_SEN
Receiver Overload POL 0.5 dBm
Receiver Reflectance TRRX -12 dB
LOS Assert LOSA -30 dBm
LOS De-Assert LOSD -14 dBm
ModuleTek Limited www.moduletek.com 3
SFP10-SR Specifications
LOS Hysteresis LOSH 0.5 dB
Notes:
1.Measured with worst ER;BER<10−12;231-1 PRBS
Electrical – Characteristics – Transmitter
VCC=3.14V to 3.46V, TC=0◦ C to 70◦ C
Parameter Symbol Min Typ Max Unit Remarks
Input differential impedance RIN 100 Ω
Differential data input swing 180 700 mV
VIN PP
Transmit disable voltage VD 2 VCC V
Transmit enable voltage VEN VEE VEE+0.8 V
Electrical – Characteristics – Receiver
VCC=3.14V to 3.46V, TC=0◦ C to 70◦ C
Parameter Symbol Min Typ Max Unit Remarks
Differential data output swing 300 850 mV
VOUT PP
Data output rise/fall time (20%-80%) tr/tf 28 ps
LOS Assert 2 V
VLOS A VCC HOST
LOS De-Assert VEE VEE+0.5 V
VLOS D
Digital Diagnostic Functions
SFP10-SR supports the 2-wire serial communication protocol as defined in SFF-8472. Digital
diagnostic information is accessible over the 2-wire interface at the address 0xA2. Digital diagnostics
for SFP10-SR are internally calibrated by default. The internal micro control unit accesses the device
operating parameters in real time,Such as transceiver temperature, laser bias current, transmitted
optical power, received optical power and transceiver supply voltage.The module implements the alarm
function of the SFF-8472,alerts the user when a particular operating parameter exceeds the factory-
set normal range.
ModuleTek Limited www.moduletek.com 4
SFP10-SR Specifications
Block-Diagram-of-Transceiver
Functions Description
The transmitter consists of a laser driver chip and a TOSA (light-emitting component). The TOSA
includes a 850nm VCSEL laser and a backlight photodetection chip, When the module is working, and
the input signal is connected to the laser driver chip.The laser driver chip supplies the bias current and
the modulation current to the laser.The laser driver chip simultaneously uses an automatic optical
power control (APC) feedback loop to maintain a constant average optical power of the laser output.
The purpose is to eliminate the change of the output optical signal due to temperature changes and
aging of the light source device.When the transmitter enable pin (TX_Disable) is high (TTL logic “1”),
the laser output is turned off. When TX_Disable is low (TTL logic “0”), the laser will turn on within
1ms.When the transmitter fault signal (TX_Fault) is reported as high,indicates a transmitter failure
caused by the transmitter’s bias current or transmitted optical power or laser tube temperature
exceeding a preset alarm threshold. Low indicates normal operation.
The receiver consists of a ROSA (light-receiving component) and a limiting amplifier chip, ROSA
includes a PIN photodetector and a transimpedance amplifier chip.When the ROSA detects the
incident light signal, it will be converted into a photo-generated current by the PIN photodetector. The
photogenerated current is converted into an electrical signal after passing through the transimpedance
amplifier. The electrical signal is further amplified by the limiting amplifier , then outputs a fixed-
amplitude electrical signal to the host.When the amplitude of the electrical signal received from the
incident light conversion of the opposite optical transceiver module is lower than the set threshold,the
module reports that the received signal is lost,the RX_LOS pin is high (logic “1”),which can be used to
diagnose whether the physical signal is normal.The signal is operated in TTL level.The microprocessor
inside the module monitors the module’s operating voltage, temperature, transmitted optical power,
received optical power, and laser bias current value in real time. The host acquires this information
over a 2-wire serial bus.
ModuleTek Limited www.moduletek.com 5
SFP10-SR Specifications
Dimensions
ALL DIMENSIONS ARE ±0.2mm UNLESS OTHERWISE SPECIFIED
UNIT: mm
ModuleTek Limited www.moduletek.com 6
SFP10-SR Specifications
Electrical Pad Layout
Pin Assignment
PIN # Symbol Description Remarks
1 Transmitter ground (common with receiver ground) 1
VEET
2 TX_FAULT Transmitter Fault
3 TX DISABLE Transmitter Disable. Laser output disabled on high or open 2
4 SDA 2-wire Serial Interface Data Line 3
5 SCL 2-wire Serial Interface Clock Line 3
6 MOD ABS Module Absent. Grounded within the module 3
7 RS0 No connection required
8 LOS Loss of Signal indication. Logic 0 indicates normal operation 4
9 RS1 No connection required 1
10 Receiver ground (common with transmitter ground) 1
VEER
ModuleTek Limited www.moduletek.com 7
SFP10-SR Specifications
11 Receiver ground (common with transmitter ground) 1
VEER
12 RD– Receiver Inverted DATA out. AC coupled
13 RD+ Receiver Non-inverted DATA out. AC coupled
14 Receiver ground (common with transmitter ground) 1
VEER
15 Receiver power supply
VCCR
16 Transmitter power supply
VCCT
17 Transmitter ground (common with receiver ground) 1
VEET
18 TD+ Transmitter Non-Inverted DATA in. AC coupled
19 TD– Transmitter Inverted DATA in. AC coupled
20 Transmitter ground (common with receiver ground) 1
VEET
Notes:
1. Circuit ground is isolated from chassis ground
2. Disabled: TDIS>2V or open,Enabled: TDIS<0.8V
3. Should Be pulled up with 4.7k –10k ohm on host board to a voltage between 2V and 3.6V
4. LOS is open collector output
References
1.IEEE standard 802.3ae. IEEE Standard Department,2005.
2. Enhanced 8.5 and 10 Gigabit Small Form Factor Pluggable Module “SFP+”–SFF-8431.
3. Digital Diagnostics Monitoring Interface for Optical Transceivers –SFF-8472.
ModuleTek Limited www.moduletek.com 8
