LM108 PDF
LM108 PDF
December 1994
Compensation Circuits
Standard Compensation Circuit Alternate* Frequency Compensation
R1 CO
Cf t
R1 a R2
CO e 30 pF
TL/H/7758 – 1 TL/H/7758 – 2
**Bandwidth and slew rate are proportional to 1/Cf *Improves rejection of power supply noise by a factor of ten.
**Bandwidth and slew rate are proportional to 1/Cs
Feedforward Compensation
TL/H/7758 – 3
2
Electrical Characteristics (Note 4) (Continued)
LM108/LM208 LM308
Parameter Condition Units
Min Typ Max Min Typ Max
Input Voltage Range VS e g 15V g 13.5 g 14 V
Common Mode
85 100 80 100 dB
Rejection Ratio
Supply Voltage
80 96 80 96 dB
Rejection Ratio
Note 1: The maximum junction temperature of the LM108 is 150§ C, for the LM208, 100§ C and for the LM308, 85§ C. For operating at elevated temperatures, devices
in the H08 package must be derated based on a thermal resistance of 160§ C/W, junction to ambient, or 20§ C/W, junction to case. The thermal resistance of the
dual-in-line package is 100§ C/W, junction to ambient.
Note 2: The inputs are shunted with back-to-back diodes for overvoltage protection. Therefore, excessive current will flow if a differential input voltage in excess of
1V is applied between the inputs unless some limiting resistance is used.
Note 3: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: These specifications apply for g 5V s VS s g 20V and b 55§ C s TA s a 125§ C, unless otherwise specified. With the LM208, however, all temperature
specifications are limited to b 25§ C s TA s 85§ C, and for the LM308 they are limited to 0§ C s TA s 70§ C.
Note 5: Refer to RETS108X for LM108 military specifications and RETs 108AX for LM108A military specifications.
Note 6: Human body model, 1.5 kX in series with 100 pF.
Schematic Diagram
TL/H/7758 – 8
3
Typical Performance Characteristics LM108/LM208
Input Currents Offset Error Drift Error
Closed Loop
Input Noise Voltage Power Supply Rejection Output Impedance
TL/H/7758 – 6
4
Typical Performance Characteristics LM308
Closed Loop
Input Noise Voltage Power Supply Rejection Output Impedance
TL/H/7758 – 7
5
Typical Applications
² Teflon polyethylene or
polycarbonate dielectric
capacitor
Worst case drift less than
2.5 mV/sec
TL/H/7758 – 4
High Speed Amplifier with Low Drift and Low Input Current
TL/H/7758 – 5
6
Typical Applications (Continued)
Fast ² Summing Amplifier
TL/H/7758 – 12
Connection Diagrams
Metal Can Package Dual-In-Line Package
TL/H/7758 – 15
TL/H/7758 – 13
Top View
*Package is connected to Pin 4 (Vb)
Order Number LM108J-8/883, LM308M or LM308N
**Unused pin (no internal connection) to allow for input anti-leakage guard
ring on printed circuit board layout.
See NS Package Number J08A, M08A or N08E
Order Number LM108H, LM108H/883,
LM308AH or LM308H
See NS Package Number H08C
TL/H/7758 – 17
Order Number LM108W/883
See NS Package Number W10A
TL/H/7758 – 16
Top View
Order Number LM108J/883
See NS Package Number J14A ² Also available per JM38510/10104
7
Physical Dimensions inches (millimeters)
8
Physical Dimensions inches (millimeters) (Continued)
9
LM108/LM208/LM308 Operational Amplifiers
Physical Dimensions inches (millimeters) (Continued)
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform can
into the body, or (b) support or sustain life, and whose be reasonably expected to cause the failure of the life
failure to perform, when properly used in accordance support device or system, or to affect its safety or
with instructions for use provided in the labeling, can effectiveness.
be reasonably expected to result in a significant injury
to the user.
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.