Engine knock down, installation
Engine knock down, installation
Knock down the parts according the following ⑴⑵(3)……steps
Installation please make the orders conversed。
⑶2nd air supplement pipe(left & right）
⑹ accelerator and clutch ⑷ thermostat in
⑵spark plug cable（left & right）
wires hose
⑽ clip
hoop
Fixture bolt
Fixture bolt
⑸ ex hose of
radiator
(1)exhaust mufflers
carburat
or
⑾ connection
plug of right
cover
⑻left side cover
⑺
shifter
⑼untie the chain
Installation Engine front side: washer2, screw cap2
Rear side: washer2, screw cap2 Fixing torque：20~30N·m
2-1
Engine knock down, installation
Cylinder head, cylinder, piston, valve system
Maintain manual
checklist
request List
Check item
DD244 DD247 DD244 DD247
Cylinder inner diameter 44~44.01mm 44.10mm
Piston outer diameter
Piston pin outer diameter 12.95-13.00
Piston pin hole outer
diameter
Gap of piston ring side
Gap of piston ring
Thickness of piston ring 1
Thickness of piston ring 2
Free distance of inner
valve spring
Free distance of outer
valve spring
Outer diameter of valve in
Outer diameter of valve ex
Torque
torque on both bolt heads on cylinder head : 18~22N·m
-2-2-
Engine knock down, installation
1. carburator
Loosen the clip bolt on carburetor, the carburetor can be taken off. When installation
on carburetor, please make the intake towards the manifold, then tighten the clip bolt.
E1
Clip hook
E1-1
Idle adjust bolt
1.Carburetor, assy. 2. Left carburetor comp. 3. Float pin. 4. Float set. 5. Gasket, float
chamber. 6. Chamber set, float. 7. Screw M4×14. 8. Clip, tube. 9. Over petrol tube.
10. Starter control rob comp. 11. Connecting petrol pipe comp. 12. Limited plate. 13.
Spring. 14. Pin, petrol. 15. Vacuum piston valve. 16. Screw M4×8. 17. Starter
thicken valve set. 18. Reset spring. 19. Right carburetor comp. 20. Screw set. 21.
Jet, slow. 22. Jet, main. 23.screw set. 24. Frament. 25. Screw M4×10. 26. Vacuum
piston valve cover. 27. Decorative cover, carburetor. 28. Bolt M4×6
-2-3-
Engine knock down, installation
2. Magneto knock down and installation
E2
remove the left crankcase cover, take off the crank
bolt, remove the flywheel( do not knock the flywheel
while removing, when install the flywheel, follow the slot
and the crankcase end). Please refer to drawing E2.
Left crankcase cover
Crankcase bolt
E3
Note:
● Check if any dust inside
● do not knock by sinker
● Install torque for crankcase bolt is 60~65N·m
Fly wheel
E4
By special tool to
disassemble
-2-4-
Engine knock down, installation
3、Rocker base
E6
Take off the two impact bolt on cylinder head cover, remove
The cylinder head cover.
Cylinder head cover
impact bolt
E7
Remove the tensioner bolt, take down the tension
tensioner
E8
Remove the 8 nuts, take off the rocker base
Torque of the 7 nut is 18～22N·m
Gap between valve : (cold) in valve 0.05～0.07mm；
exhaust valve 0.06～0.08mm Main chain Nut
E9
4、Camshaft installation and disassemble
remove the main chain and sprocket wheel,
take out the camshaft
Sprocket
wheel
Cam haft
-2-5-
Engine knock down, installation
E10
Note:
When install the sprocket wheel and camshaft; piston is located
at the end of compression stroke , please refer to drawing E10 at
right side, the reticle at positive time of sprocket wheel is flat
aligned with the cam platform of cylinder head.
please refer to drawing E11, the reticle of flywheel should be
alignment with the threaded slot of the left cylinder cover. Shaft sleeve Flat align
the pin of the shaft sleeve of camshaft should be set into the
pin slot, E11
Reticle align with slot
5、Cylinder head remove and installation E12
Remove the cylinder head by taking out the camshaft,
Disassemble the bolt on cylinder body and cylinder head
When installation, do not forget to put the washer ,
Oriented pin and O ring
E12-1
bolts
Cylinder head
E13
Oriented plank
Cylinder body
Upper washer of cylinder
body
-2-6-
Engine knock down and installation
6、cylinder body
Cylinder head can is removed by removed the cylinder E14
head, take the oriented plank out.
Oriented pin
E14-1
piston
oriented pin and E15
O ring
Underneath Tensionor
gasket
Remove the piston pi ring(E15) by pincer, push out the
Pisont pin, Remove the piston out.
When installation, please block the intake by clean cloth
To avoid the ring falling down into the cylinder body.
The “IN” mark means intake
Piston pin ring
7、
Clutch E16
First please exclude the oil in the crankcase, remove
the right crankcase cover
When installation the right crankcase cover, pay attention
To the same direction of the water pump spindle and the
Oil pump spindle and do not fall down the ex-oil pipe
(E16，E17，E18.)
E19-1 Right crankcase cover
Water pump spindle
-2-7-
Engine installation and disassemble
Oil pump driven gears
Oil pump
Remove the hexagon nut, primary transmission gears, remove E18
the clutch pusher tray, remove the clutch by special tool (E19-1, E20).
Before installation, check the scar and color of clutch friction.
Replace it when necessary.
Please make sure that the smaller
round nut end outwards by using the torque 50-56N.m
Ex oil tube
Clutch outer tray
Hexagon nut
primary transmission gears Clutch inside tray
8. oil pump
Remove the oil pump(E18), pay attention to the O ring, please clean
the
Filter screen before installing the oil pump, and also the O ring
E19
Shift supporting roller Clutch outer tray
E20
Oil pump assy. gear cam
Gear shank
oil pump driven
oil filter screen
gears
(clean it before
installation)
E21
-2-8-
Engine installation and disassemble
9、shift gears installation and dissamble E22
Remove the gear supporting roller, gear cam in turn, take out
Gear shank, loose the mounting bolt, remove the right
crankcase
(drawing E21 , E22)
Note: turning spring of gear supporting roller should be
in right place ; the gear cam pin should be aimed at when
installing
the gear cam.
Right crankcase
1. Mainshaft comp 2. Gear, mainshaft second 3. Gear, mainshaft third 4. Gear,
mainshaft fourth 5. Gear, mainshaft fifth 6. Washer ,spline 7. Set ring 8. Washer 9.
Shaft bush spline 10. Washer thrust 11. Countershaft comp 12. Gear, countershaft
first 13. Gear, countershaft second 14. Gear, countershaft third 15. Gear, countershaft
fourth 16. Gear, countershaft fifth 17. Bush 18. Washer 19. Collar（A） 20. Collar（B）
21. Sprocket, counter shaft 22. Plate, fixing 23.
Bolt M6×10/ZnD Mainshaft Gear fork、gear fork shaft
comp
10、crankshaft installation and remove
remove mainshaft set, side shaft set, gear fork, gear
fork shaft and cam shift kettle, loose the crankshaft E23
mounting bolt, then the crankshaft could be taken off.
Please clean the mainshaft and sideshaft before
installation. Pay attention not forget to put the washer
E24
Crank
shaft Side shaft set cam shift
kettle
-2-9-
Engine lubrication system
11、Engine lubrication system chart
cam
Camshaft camshaft
bearing rocker
side shaft rolling
bearing Side shaft set
Mainshaft
rolling bearing Mainshaft
主轴滚针轴承 set
Oil pump
Crank Crank
pin
Oil filter screen
网
crankcase
-2-10-
Engine cooling system
12、engine cooling system chart
Assistant
water box
Radiator cap （to
put water）
Radiator
fan
-2-11-
Engine cooling system
water pump breakdown chart：
1 Water pump comp 2. Water pump hull 3. Water pump cover 4. Water pump shaft 5. Fan
6. Retaining ring 8 7. O-ringφ36x2 8. Bearing 6200 9. Water seal A 10. Water seal B 11.
Oil seal 21x10x5 12. O-ring of pump cover 13. Bolt M6x30 14. Bearing 6000 15. Bolt
M6x40 16. Hose connector setting plate 17. Hose connector 18. O-ring φ17x1.8 19. Bolt
M6x12 20. Washer 6
-2-12-
