Scribd
Upload
160 views3 pages

Manual-balanceo-De-carga PCC Router Bridge 4 ADLS

This document provides instructions for load balancing across 4 internet connections of equal speed using PCC routing on a MikroTik router. It outlines 9 steps to configure the router interfaces, create PPPOE connections, set the LAN IP, enable NAT and routing, configure connection marking and policies, and set up DNS servers. The steps include naming interfaces, creating PPPOE clients, setting the LAN IP, enabling NAT and routing between interfaces, load balancing traffic using connection marking policies, and configuring public DNS servers for protection against DNS port attacks.

Uploaded by

Andres Toloza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
160 views3 pages

Manual-balanceo-De-carga PCC Router Bridge 4 ADLS

This document provides instructions for load balancing across 4 internet connections of equal speed using PCC routing on a MikroTik router. It outlines 9 steps to configure the router interfaces, create PPPOE connections, set the LAN IP, enable NAT and routing, configure connection marking and policies, and set up DNS servers. The steps include naming interfaces, creating PPPOE clients, setting the LAN IP, enabling NAT and routing between interfaces, load balancing traffic using connection marking policies, and configuring public DNS servers for protection against DNS port attacks.

Uploaded by

Andres Toloza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

Manual de balanceo de carga PCC para 4 Lineas de Internet de la misma Velocidad

si sigues estos 9 pasos basicos tendra tu balaneco Operando de manera correcta

PASO 1

Nombrando las interfaces

aqui se deben identificar las interfaces que van a usar

/interface ethernet
set [ find default-name=ether1 ] comment=Ether1 name=WAN1
set [ find default-name=ether2 ] comment=Ether2 name=WAN2
set [ find default-name=ether3 ] comment=Ether3 name=WAN3
set [ find default-name=ether4 ] comment=Ether4 name=WAN4
set [ find default-name=ether5 ] comment=Ether5 name=LAN

PASO 2

Creando las conexiones pppoe-client

Ojo!

en mi caso

password=\bandaancha09 tu debes averiguar el password de tu cuenta PPPoE con el


proveedor

user=tr069movistar tu debes averiguar el user de tu cuenta PPPoE con el proveedor

/interface pppoe-client
add disabled=no interface=WAN1 mrru=1600 name=pppoe-out1 password=\
bandaancha09 user=tr069movistar
add disabled=no interface=WAN2 mrru=1600 name=pppoe-out2 password=\
bandaancha09 user=tr069movistar
add disabled=no interface=WAN3 mrru=1600 name=pppoe-out3 password=\
bandaancha09 user=tr069movistar
add disabled=no interface=WAN4 mrru=1600 name=pppoe-out4 password=\
bandaancha09 user=tr069movistar

PASO 3

Configurando las direeciones IP en la interface LAN

/ip address
add address=192.168.1.1/24 interface=LAN network=192.168.1.0

PASO 4

Enmascarando las interfaces pppoe-client


/ip firewall nat
add action=masquerade chain=srcnat out-interface=pppoe-out1
add action=masquerade chain=srcnat out-interface=pppoe-out2
add action=masquerade chain=srcnat out-interface=pppoe-out3
add action=masquerade chain=srcnat out-interface=pppoe-out4

PASO 5

creando las rutas

/ip route
add gateway=pppoe-out1 check-gateway=ping distance=1
add gateway=pppoe-out2 check-gateway=ping distance=2
add gateway=pppoe-out3 check-gateway=ping distance=3
add gateway=pppoe-out4 check-gateway=ping distance=4

Paso 6

/ip firewall mangle


add chain=prerouting in-interface=pppoe-out1 connection-state=new new-connection-
mark=pppoe-out1_conn action=mark-connection passthrough=yes
add chain=prerouting in-interface=pppoe-out2 connection-state=new new-connection-
mark=pppoe-out2_conn action=mark-connection passthrough=yes
add chain=prerouting in-interface=pppoe-out3 connection-state=new new-connection-
mark=pppoe-out3_conn action=mark-connection passthrough=yes
add chain=prerouting in-interface=pppoe-out4 connection-state=new new-connection-
mark=pppoe-out4_conn action=mark-connection passthrough=yes

add chain=output connection-mark=pppoe-out1_conn new-routing-mark=to_pppoe-out1


action=mark-routing passthrough=yes
add chain=output connection-mark=pppoe-out2_conn new-routing-mark=to_pppoe-out2
action=mark-routing passthrough=yes
add chain=output connection-mark=pppoe-out3_conn new-routing-mark=to_pppoe-out3
action=mark-routing passthrough=yes
add chain=output connection-mark=pppoe-out4_conn new-routing-mark=to_pppoe-out4
action=mark-routing passthrough=yes

Paso 7

/ip firewall mangle


add chain=prerouting in-interface=LAN connection-state=new dst-address-type=!local
per-connection-classifier=both-addresses:4/0 action=mark-connection new-connection-
mark=pppoe-out1_conn passthrough=yes
add chain=prerouting in-interface=LAN connection-state=new dst-address-type=!local
per-connection-classifier=both-addresses:4/1 action=mark-connection new-connection-
mark=pppoe-out2_conn passthrough=yes
add chain=prerouting in-interface=LAN connection-state=new dst-address-type=!local
per-connection-classifier=both-addresses:4/2 action=mark-connection new-connection-
mark=pppoe-out3_conn passthrough=yes
add chain=prerouting in-interface=LAN connection-state=new dst-address-type=!local
per-connection-classifier=both-addresses:4/3 action=mark-connection new-connection-
mark=pppoe-out4_conn passthrough=yes

/ip firewall mangle


add chain=prerouting in-interface=LAN connection-mark=pppoe-out1_conn action=mark-
routing new-routing-mark=to_pppoe-out1 passthrough=yes
add chain=prerouting in-interface=LAN connection-mark=pppoe-out2_conn action=mark-
routing new-routing-mark=to_pppoe-out2 passthrough=yes
add chain=prerouting in-interface=LAN connection-mark=pppoe-out3_conn action=mark-
routing new-routing-mark=to_pppoe-out3 passthrough=yes
add chain=prerouting in-interface=LAN connection-mark=pppoe-out4_conn action=mark-
routing new-routing-mark=to_pppoe-out4 passthrough=yes

Paso 8

Configurando las rutas, recuerdan las marcas de ruta que hicimos en los pasos 6 y
7 , to_pppoe-out1, to_pppoe-out2, to_pppoe-out3, to_pppoe-out4 vamos a usarlas
ahora!

/ip route
add gateway=pppoe-out1 routing-mark=to_pppoe-out1 check-gateway=ping
add gateway=pppoe-out2 routing-mark=to_pppoe-out2 check-gateway=ping
add gateway=pppoe-out3 routing-mark=to_pppoe-out3 check-gateway=ping
add gateway=pppoe-out4 routing-mark=to_pppoe-out4 check-gateway=ping

Paso 9

Configurando los DNS Publicos

/ip dns
set allow-remote-requests=yes servers=8.8.8.8,8.8.4.4

Reglas de seguridad y proteccion para ataques al puerto 53 del DNS

/ip firewall filter


add action=drop chain=input comment="Block Intrusos DNS" dst-port=53 in-
interface=pppoe-out1 protocol=udp
add action=drop chain=input comment="Block Intrusos DNS" dst-port=53 in-
interface=pppoe-out2 protocol=udp
add action=drop chain=input comment="Block Intrusos DNS" dst-port=53 in-
interface=pppoe-out3 protocol=udp
add action=drop chain=input comment="Block Intrusos DNS" dst-port=53 in-
interface=pppoe-out4 protocol=udp

You might also like