Xitanium
LED driver
Datasheet
Xitanium Highbay LED Drivers Dimmable (1-10V) Independent
Xitanium Dim 100W 1.05A 1-10V 230V I165C
LED-based light sources are an excellent solution for highbay industrial applications. They are long-lasting and require
low maintenance. However, to get the best out of the LEDs, these light sources require highly reliable and efficient LED
Drivers. Philips Xitanium Dimmable (1-10V) LED Outdoor Drivers are specifically designed to deliver reliable performance
and protection while meeting the strict performance, approbation and application requirements.
Benefits Features Application
• Ultimate robustness and reliability • Proven robustness and reliable • Highbay industrial lighting
secure the lowest luminaires electronic driver design • Warehouse lighting
maintenance overtime • Achieving highest efficiencies based • Big-box retail store lighting
• Best in class, thermal performance on advanced technology
withstanding harsh High-bay industry • Extremely long lifetime, fitting with
applications highbay industrial applications
• Consistent waterproof performance • Independent/IP67 rated
throughout the lifecycle • Dimmable through 1-10V interface
• Easy to design-in, based on broad • Suitable for IEC insulation Class I
compatibility and superior thermal systems
management • Authorized certificates: CE, ENEC,
• Backed by a 5 year warranty from a CB and CCC
company you can trust
March 2017
Electrical input data
Specification item Value Unit Condition
Nominal input voltage 220...240 Vac
Nominal input frequency 50...60 Hz
Nominal input current 0.51 A @230V @ full load
Max. input current 0.56 A @ minimum input voltage AC
Input voltage 230 Vac
Nominal input power 112 W @230V @ full load
Power factor ≥ 0.98 @ full load. See graph.
Total harmonic distortion < 10 % @ full load. See graph.
Efficiency 91 % @230V @ full load
Input voltage AC 85...305 Vac Safety operational range
Input frequency AC 45...66 Hz Operational range
Isolation Input to Output Basic
Electrical output data
Specification item Value Unit Condition
Regulation method Constant Current
Output voltage 46...95 Vdc
Output voltage max 170 Vdc Peak voltage at open load
Output current 1.05 A Full output current setting
Output current min dimming 105 mA
Output current tolerance ±5 %
Output current ripple LF <5 % Ripple = peak / average @ 1KHz
Output current ripple HF ≤ 15 %
Output power 100 W Full output
Electrical data controls input
Specification item Value Unit Condition
Control method 1-10V Output current amplitude dimming, 1-10V acc. IEC60929
Dimming range 10...100 % 1-9V
Galvanic Isolation Basic
Logistical data
Specification item Value
Product name Xitanium Dim 100W 1.05A 1-10V 230V I165C
Order code
Logistic code 12NC 9290 014 25680
EAN3
Pieces per box 12
2/7 Xitanium Dim 100W 1.05A 1-10V 230V I165C March 2017
Wiring & Connections
Specification item Value Unit Condition
Input Wire Size 1.0 mm2 3-wire cable: 300V/500V rating or higher
Output Wire Size 1.0 mm2 2-wire cable: 300V/500V rating or higher
Input Wire Length 450 ± 30 mm Out of enclosure
Output Wire Length 480 ± 30 mm Out of enclosure
Control Wire Size 1.0 mm 2-wire cable: 300V/500V rating or higher
Control Wire Length 200 mm Out of enclosure and not including connector length
1-10V + (Brown)
1-10V - (Blue) (Brown) LED +
LED
Line (Brown) DRIVER (Blue)
Neutral (Blue) LED -
Ground (Green/Yellow)
Insulation
Insulation Mains LED 1-10V
Mains Basic Basic
LED Basic Basic
1-10V Basic Basic
Dimensions and weight
Specification item Value Unit Condition
Length (A3) 167 mm
Width (B3) 65 mm
Width (B1) 18 mm
Height (C2) 73 mm
Fixing hole distance (A1) 125 mm
3/7 Xitanium Dim 100W 1.05A 1-10V 230V I165C March 2017
Operational temperatures and humidity
Specification item Value Unit Condition
Ambient Temperature -40 … +70 °C Higher ambient temperature allowed as long
as Tcase-max is not exceeded
Starting Ambient temperature -40 … +70 °C
Tcase-max 85 °C Maximum temperature measured at Tcase-point
Maximum housing temperature 90 °C In case of a failure
Relative humidity 10...90 % Non-condensing
Storage temperature and humidity
Specification item Value Unit Condition
Ambient temperature -40...+85 °C
Relative humidity 5 ... 95 % Non-condensing
Lifetime
Specification item Value Unit Condition
Driver lifetime 50,000 hours Measured temperature at Tcase-point is
Tcase-max.
Maximum failures = 10%
Programmable features
Specification item Value Remark Condition
Set output current (AOC) No See Default output current: =1050 mA
Design-in guide
Features
Specification item Value Remark Condition
Open load protection Yes Automatic recovering
Short circuit protection Yes Automatic recovering
Over power protection Yes Automatic recovering
Hot wiring No
Suitable for fixtures with protection class I per IEC60598
Over temperature protection driver Yes Automatic recover
Certificates and Standards
Specification item Value
Approval Marks CB / CCC / CE / ENEC
Ingress Protection Rating IP 67
4/7 Xitanium Dim 100W 1.05A 1-10V 230V I165C March 2017
Inrush current
Specification item Value Unit Condition
Inrush Current Ipeak 43.2 A Input voltage 230V
Inrush Current Twidth 460 µs Input voltage 230V, measured at 50% Ipeak
Drivers / MCB 16A Type B 6 pcs
MCB Rating Relative number of LED drivers
B 10A 63%
B 13A 81%
B 16A 100% (stated in datasheet)
Ipeak B 20A 125%
T width B 25A 156%
C 10A 104%
C 13A 135%
C 16A 170%
C 20A 208%
C 25A 260%
Driver touch current
Specification item Value Unit Condition
Typical touch current < 0.6 mA peak Acc. IEC61347-1. LED module contribution not
included
Surge immunity
Specification item Value Unit Condition
Mains surge immunity (diff. mode) 4 kV Acc. IEC61000-4-5. 2 Ohm, 1.2/50us, 8/20us
Mains surge immunity (comm. mode) 6 kV Acc. IEC61000-4-5. 12 Ohm 1.2/50us, 8/20us
Control surge immunity (diff. mode) 0.5 kV Acc. IEC61000-4-5. 2 Ohm 1.2/50us, 8/20us
Control surge immunity (comm. mode) 6 kV Acc. IEC61000-4-5. 12 Ohm 1.2/50us, 8/20us
Additional information
Specification item Value Unit Condition
1-10V ON See Design-in In case of EMI test for the critical configuration,
guide please contact Philips for additional filter
recommendation.
5/7 Xitanium Dim 100W 1.05A 1-10V 230V I165C March 2017
Graphs
Operating window
100
Output Voltage (V)
90
80
70
60
50
40
0 0.2 0.4 0.6 0.8 1.0 1.2
Output Current (A)
Power factor versus output power
1.1
Vin=202
Power Factor
1.0 Vin=230
Vin=254
0.9
0.8
0.7
0.6
0.5
0 20 40 60 80 100 120
Output Power (W)
Total Harmonic Distortion
45
Vin=202
40
Vin=230
THD ( % )
35 Vin=254
30
25
20
15
10
0
0 20 40 60 80 100 120
Output Power (W)
6/7 Xitanium Dim 100W 1.05A 1-10V 230V I165C March 2017
Efficiency versus output power
100
Vin=202
Vin=230
Efficiency
Vin=254
90
80
70
60
0 20 40 60 80 100 120
Output Power (W)
Dimming curve
1.2
1
Iout (A)
0.8
0.6
0.4
0.2
0
0 2 4 6 8 10 12 14
Vdim (V)
Lifetime vs Tcase
100
90
Lifetime (Khrs)
80
70
60
50
40
30
20
10
0
10 20 30 40 50 60 70 80 90
o
Tc ( C )
©2017 Koninklijke Philips Electronics N.V.
All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and
reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use.
Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Data subject to change.
Date of release: March 22, 2017
www.philips.com
