Intake Series Amplifiers

/
A2002V / A4002V / A8002V
A4004V / A6004V / A8000V / A16000V
 The Audiobahn Way

To bring the product to market that excites the consumer through

sound and vision from an orientation of integrity and customer service. We
make you look as good as you sound. We strive to take car audio to an
extreme the world has never seen, and a world that never stops evolving.

Audiobahn was established in 1997 with one long-term goal in mind,

"Build it Bigger, Badder, & Better, and the people will take notice!" We
back this statement with an engineering team that has brought home several
Innovations, Design & Engineering Showcase Awards, and a marketing team
from around the world that spends countless hours developing our no
compromise products to satisfy the most discriminating enthusiasts.

Our global manufacturing facilities feature ISO9002 ratings (the highest

level of quality control awarded in the electronics manufacturing industry), fully
robotic assembly lines and a state of the art, California based R & D
laboratory.

Due to overwhelming response from our competitors, and our goal to

participate in even more events this year, we created *"TEAM AUDIOBAHN."
This organization is designed to create a support network along with shirts and
perks for team members. "TEAM AUDIOBAHN" is not only for the diehard
competitor, but also for anyone that loves car audio as much as we do. With
four levels of play, one is right for you to get started in the Audiobahn family.

Our Technical Department and entire staff look to strive above and
beyond the rest of the pack by going that extra mile to help you out. Whether
you happen to be a veteran competitor, or a beginner car audio enthusiast
who does not know a voice coil from a spider. We are all her to help you get
the best system you can with what you have.

Judge for yourself, and remember what it's all about, "If it's not
Bigger, Badder & Better, it's not Audiobahn." If audio is your life,
Audiobahn is the brand for you! We make you look as good as you sound.
People never stop trying to get the best product, so we will never stop making
it.

*To learn more about "TEAM AUDIOBAHN" please give us a call, see our website at
website at www.audiobahn.com, or email us at [email protected] to learn about all the
details.
Table of Contents

Introduction 3

Features and Specifications 4

Control and Functions 5-15

A2002V 5

A4002V 6

A8002V 7
A4004V / A6004V 8

A8000V / A16000V 9

High Level Input Wiring 16-17

A2002V /A8002V / A8000V / A16000V 16

A4002V 16

A4004V / A6004V 17

Planning / Mounting Your System 18

Wiring Diagrams 19-21

A2002V / A4002V / A8002V 19

A4004V / A6004V 20-21
A8000V / A16000V 21

Adjustments and Tunning 22

Trouble Shooting 23

Warrning / Disclaimer 24

Warranty 25-26

2
Introduction

Dear Customer,

Congratulations on your purchase of the worlds finest brand of car audio products. Here at
Audiobahn Inc. we are devoted to making our musical reproduction the vert best, and we are
pleased you have chosen our product. Through years of engineering expertise, hand
craftsmanship, and critical testing procedures, we have created a wide range of products that
reproduce music with all the clarity and richness you deserve.

For maximum performance we recommend you have your Audiobahn product installed by an
Authorized Audiobahn Dealer, as we provide specialized training through our Audiobahn
Installer Training Programs. Please read your warranty, keep your receipt, and original carton
for possible future use.

To get a free brochure on Audiobahn products in the US call (714) 988-0400 or e-mail us at
[email protected].

WARNING
Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss. High powered autosound systems may produce sound pressure levels
well over 135dB. Need we say more! Use common sense.

If after reading this manual you still have questions regarding your product, we
recommend that you see your nearest Audiobahn Dealer. A list of Authorized
Audiobahn Dealers can be found on our web page. If you need further assistance, feel
free to call us at (800) 488-8595 and ask for the Technical Department. Be sure to have
the model number, date of purchase, and invoice number available when you call.

The model number can be located on the outside of the carton. Record this in the space
provided below along with the date of purchase. It is a good idea to keep your receipt
with this as you will need it in the case of needing a warranty, repair service or
exchange.

Model Number:___________________ Date of Purchase: _____________________

3
 remote

On-Board Digital Volt Meter

Input Sensitivity 200mV - 8V

,
&

(A2002V : 25A x 1) (A4002V : 40A x 1) (A8002V : 30A x 2) (A4004V : 20A x 2)

(A6004V : 25A x 2) (A8000V : 30A x 2) (A16000V : 40A x 2)

A2002V : 400 watts ACH Power A4004V : 800 watts ACH Power
50 watts x 2 @ 4 Ohms RMS power 50 watts x 4 @ 4 Ohms RMS power
100 watts x 2 @ 2 Ohms RMS power 100 watts x 4 @ 2 Ohms RMS power
200 watts x 1 @ 4 Ohms RMS power 200 watts x 2 @ 4 Ohms RMS power
A4002V : 800 watts ACH Power A6004V : 1200 watts ACH Power
100 watts x 2 @ 4 Ohms RMS power 75 watts x 4 @ 4 Ohms RMS power
200 watts x 2 @ 2 Ohms RMS power 150 watts x 4 @ 2 Ohms RMS power
400 watts x 1 @ 4 Ohms RMS power 300 watts x 2 @ 4 Ohms RMS power
A8002V : 1600 watts ACH Power A8000V : 1600 watts ACH Power
200 watts x 2 @ 4 Ohms RMS power 400 watts x 1 @ 4 Ohms RMS Power
400 x 2 @ 2 Ohms RMS power 800 watts x 1 @ 2 Ohms RMS power
800 watts x 1 @ 4 Ohms RMS power
A16000V : 3200 watts ACH Power
800 watts x 1 @ 4 Ohms RMS Power
1600 watts x 1 @ 2 Ohms RMS power

A2002V (W x H x D) 11 1/16" x 2 1/8" x 6 13/16" 281 x 55x 173.0mm

A4002V (W x H x D) 11 1/16" x 2 1/8" x 8 3/8" 281 x 55 x 212.7mm
A8002V (W x H x D) 11 1/16" x 2 1/8" x 11 7/8" 281 x 55 x 282.6mm
A4004V (W x H x D) 11 1/16" x 2 1/8" x 9 1/8" 281 x 55 x 231.8mm
A6004V (W x H x D) 11 1/16" x 2 1/8" x 9 7/8" 281 x 55 x 250.8mm
A8000V (W x H x D) 11 1/16" x 2 1/8" x 11 7/8" 281 x 55 x 301.6mm
A16000V (W x H x D) 11 1/16" x 2 1/8" x 15 5/8" 281 x 55 x 398mm
4
 BASS
LPF X-OVER HPF SUB SONIC LEVEL LEVEL INPUT
BOOST
DVM REMOTE
HPF +L-G-R-
LPF FULL ON OFF ON OFF
POWER
SEAN AND WILSON ROCK

PROTECTION

50 120 50 750 20 50 MIN MAX

A2002V FRONT
Controls and Functions

12 13 7 6 8 14 9 5 16

5
Patent: DES 423,503

LOW INPUT LINE OUT

SPEAKER
ON OFF POWER
BRIDGED L L

LCH RCH GND REM BATT

R R

A2002V REAR

1 2 3 4 10 11
 BASS
LPF X-OVER HPF SUB SONIC LEVEL LEVEL INPUT
BOOST
DVM REMOTE
HPF +L-G-R-
LPF FULL ON OFF ON OFF
POWER
SEAN AND WILSON ROCK

PROTECTION

50 120 50 750 20 50 MIN MAX

Controls and Functions

A4002V FRONT
12 13 7 6 8 14 9 5 16

6
LOW INPUT LINE OUT
SPEAKER
POWER
BRIDGED L L

LCH RCH GND REM BATT

R R

A4002V REAR

1 2 3 4 10 11
 BASS
LPF X-OVER HPF SUB SONIC LEVEL LEVEL INPUT
DVM REMOTE BOOST
HPF +L-G-R-
LPF FULL ON OFF ON OFF
POWER
SEAN AND WILSON ROCK

PROTECTION

50 120 50 750 20 50 MIN MAX

Controls and Functions

A8002V FRONT
12 13 7 6 8 14 9 5 16

7
Patent: DES 423,503

LOW INPUT LINE OUT

SPEAKER
POWER
BRIDGED L L

LCH RCH GND REM BATT

R R

A8002V REAR

1 2 3 4 10 11
 BASS
LPF X-OVER HPF SUB SONIC LEVEL
DVM REMOTE BOOST
LEVEL INPUT
+L-G-R-

SEAN AND WILSON ROCK

ON OFF ON OFF POWER

50 120 50 750 20 50 MIN MAX
PROTECTION

50 120 50 750 ON OFF ON OFF 20 50 MIN MAX

Controls and Functions

12 13 7 6 8 14 9 5 16

A4004V/A6004V FRONT

8
Patent: DES 423,503

LINE OUT CH1 CH2 CH3 CH4 LOW INPUT

BRIDGED BRIDGED
POWER
1 1 3

GND REM BATT

2 2 4

CH1 CH2 CH3 CH4

CH1 CH2 CH3 CH4

11
A4004V/A6004V REAR 1 2 3 4 10
A8000V/A16000V FRONT

BASS PHASE
LPF X-OVER SUB SONIC LEVEL LEVEL INPUT
BOOST SHIFT
DVM REMOTE
ON OFF +L-G-R-
LPF FULL 180 0
POWER
SEAN AND WILSON ROCK

PROTECTION

50 120 MIN MAX 20 50 MIN MAX

Controls and Functions

12 13 7 6 14 15 9 5 16

�
Patent: DES 423,503

LOW INPUT LINE OUT

SPEAKER
POWER
L L

GND REM BATT

R R

A8000V/A16000V REAR

1 2 3 4 10 11
Controls and Functions

Controls and Functions

1. Speaker Terminals SPEAKER

Bridged

L R

A2002V
A4002V
A8002V

CH1 CH2 CH3 CH4

Bridged Bridged

A4004V
CH1 CH2 CH3 CH4
A6004V

Speaker

A8000V
A16000V

These chrome plated connectors can accept from 16 to 8 gauge wire. Be careful to observe proper polarity when
connecting the cables

2. B - Terminal (Chassis ground)

POWER

GND REM BATT

A2002V
A4002V
A8002V
A4004V
A6004V
A8000V
A16000V

To avoid unwanted ignition noise caused by ground loops, it is essential that the amplifier be grounded to a
clean, bare, metal surface of the vehicles chassis.

Note: GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT. (1 METER)
Controls and Functions

Controls and Functions

3. Remote Turn-On Input

POWER

GND REM BATT A2002V

A4002V
A8002V
A4004V
A6004V
A8000V
A16000V

To remote or power antenna output of car stereo. This amplifier is turned "ON" remotely when the vehicle's stereo
is turned "ON".

Note: IF YOUR RADIO DOES NOT HAVE +12 VOLT OUTPUT LEAD WHEN THE RADIO IS TURNED ON, THE
"REMOTE" TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO THE VEHICLE'S ACCESSORY
CIRCUIT THAT IS LIVE WHEN THE KEY (IGNITION) IS "ON".

4. B+ Terminal (Battery Positive)

POWER
A2002V
GND REM BATT
A4002V
A8002V
A4004V
A6004V
A8000V
A16000V

Due to the power requirements of the amplifier, this connection should be made directly to the positive (+)
terminal of the battery. For a safety measure, install an in-line fuse holder (not included) as close to the battery
positive (+) as possible with an apmere rating not to exceed the total value of fuses in the amp.

5. Input Sensitivity Adjustment

MIN MAX

MIN MAX A2002V

A4002V
MIN MAX
A8002V
A8000V A4004V
A16000V A6004V

This control adjusts the amplifier's sensitivity to match the signal strength coming from the source unit. Input
sensitivity is variable from 200 Millivolts to 8 volts. Clockwise increases sensitivity. Counterclockwise decreases
sensitivity. THE KNOB IS NOT A VOLUME CONTROL. A lower signal level will require increased sensitivity for
full power. A higher signal will require decreased sensitivity.
11
A2002V
A4002V A4004V A8000V
A8002V A6004V A16000V

A2002V
A4002V
A8002V
A8000V A4004V
A16000V A6004V

A2002V
A4002V A4004V
A8002V A6004V
A2002V
A4002V
A8002V
A8000V A4004V
A16000V A6004V

A2002V
A4002V
A8002V
A8000V A4004V
A16000V A6004V

A2002V
A4002V
A8002V
A8000V A4004V
A16000V A6004V
Controls and Functions

Controls and Functions

12. DVM (Digital Volt Meter Input) Fig 1

A2002V
DVM REMOTE A4002V
A8002V
A4004V
A6004V
A8000V
A16000V

Remote Control for Digital Display Voltmeter: Optional ADM100T

12. DVM (Digital Volt Meter Input) Fig 1

A2002V
DVM REMOTE A4002V
A8002V
A4004V
A6004V
A8000V
A16000V

Bass Boost Control (MIN / MAX) : Optional ABR100T

14. Bass Boost Switch and Variable

BASS BASS
BASS BOOST
BOOST
BOOST ON OFF
ON OFF
A2002V
A4002V
MIN MAX
A8002V
A8000V A4004V A8000V
A16000V ON OFF A6004V A16000V

Bass Boost Switch: ON and OFF Bass Boost Variable: 0dB - 18dB @ 45Hz

15. Phase Shift Switch

Phase
Shaft
o o
180 0

A8000V
A16000V

PHASE SHIFT SWITCH (0 AND 180 DEGREES): Allows you to change the phase of your subwoofer from 0
and 180 degrees to help compensate
o for timing differences between drivers.
14
Controls and Functions

Control and Functions

16. LED indicator (Status)

POWER A2002V
A4002V
A8002V
A4004V
PROTECT A6004V
A8000V
A16000V

-PWR (Power) : This BLUE LED will illuminate when the amplifier is turned "ON". If it fails to illuminate, check the power
connections to the amplifier and fuses.

- PROT (Protection) : The amplifier protection circuitry will disable the amplifier if input overload, short circuit, or extremely
high temperature conditions are detected. When the protection mode is in operation, the LED indicator on the side
panel will be illuminated, indicating the amplifier has gone into a self-preservation mode.

If you observe that the protection LED is lit, please check the system carefully to determine what has caused the
protection circuit to engage. The amplifier shut down due to a thermal overload condition, please allow it to cool
down before restarting. If the amplifier shut down because of an input overload or short circuit, be sure to repair these
conditions before attempting to power up the amplifier again.

Fig 1.

LINE CODE

Optional Remote Digital Volt Meter : ADM-100T

Fig 2.

LINE CODE

Optional Remote Bass Boost Control : ABR-100T

MIN MAX

15
High Level Input Wiring

If the HIGH LEVEL INPUTS are used, do not use the low level RCA inputs at the same time

A2002V / A4002V / A8002V / A8000V / A16000V

����������
�����

�����
� � ������������
� ����������
�� ��� ���

HIGH INPUT

+L-G-R+

���

L+
L-
CHASSIS GND
R-
R+

DES. 423,503

16
High Level Input Wiring

A4004T / A6004V
����������
�����

�����
� � ������������
� ����������
�� ��� ���

HIGH INPUT

+L-G-R+

���

1+
2+
CHASSIS GND
3+
4+

DES. 423,503

17
Planning and Mounting Your System

Planning Your System

Before beginning the installation, consider the following:

a. If you plan to expand your system by adding other components sometime in the
future, ensure that adequate space is left, and cooling requirements are met.
If your radio/source is equipped with Pre-Amp outputs, it is possible to utilize them
to drive an Amplifier and connecting (Amplifier) to the 2 rear speakers.
Then, use the built-in power of your radio to drive the 2 front speakers.

NOTE:
DISTORTION LEVEL IS CONSIDERABLY LOWER FROM PRE-AMP (LOW LEVEL)
OUTPUTS, THAN SPEAKER (HIGH LEVEL) OUTPUTS.
b. Are your components matched? The RMS power rating of your speakers must be
equal or greater than the Amplifier's. They also must be 1-8 Ohms impedance
(this information is normally printed on the speaker magnet).
c. Consider both the length of your leads, and routing when determining the mounting
location. Pre-Amp input Jacks require a length of high quality shielded male to male
RCA patch cord.

Mounting Your System

The mounting position of your Amplifier will have a great effect on its ability to dissipate
the heat generated during normal operation. It has an ample heat sink for heat
dissipation, and also is designed with a thermal shut-down (for heat protection)circuit,
having enough air directed over the cooling fins will improve heat dissipation dramatically.
DO NOT enclose the amplifier in a small box or cover it so that air can not flow around
the fins. Temperatures in car trunks have been measured as high as (155 F) in the
summer time. Since the thermal shut-down point for the Amplifier is (158 F) it is easy
to see that it must be mounted for maximum cooling capability. To achieve the maximum
advantage of convection air flow in an enclosed trunk, mount the amplifier in a horizontal
position. Cooling requirements are considerably relaxed when mounting inside the
passenger compartment since the driver will not allow temperatures to reach a critical
point. Floor mounting under the seat is usually satisfactory as long as there is at least 1
inch (2.54 cm) above the Amplifier's fins for ventilation.

a. Select a suitable location that is convenient for mounting, accessible for wiring and
has ample room for air circulation and cooling.
b. Use the amplifier as a template to mark the mounting holes. Remove the amplifier
and drill holes. Use extreme caution. Inspect underneath the surfaces before drilling!
c. Secure the Amplifier using the screws provided.
CAUTION: Before connecting any wires to the amplifier, disconnect the ground lead from
the battery. Leave the ground lead disconnected until you are done wiring the
amplifier.

18
Wiring Diagrams

A2002V / A4002V / A8002V

MONO MODE
BRIDGED

L R

SUBWOOFER
4~8 OHM

STEREO MODE BRIDGED

L R

LEFT SPEAKER RIGHT SPEAKER

2~8 OHM 2~8 OHM

TRI MODE

BRIDGED

L R BRIDGED
4~8 OHM

LEFT SPEAKER RIGHT SPEAKER

4~8 OHM 4~8 OHM

: INDUCTOR LOW PASS FILTER : CAPACITOR HIGH PASS FILTER

19
Wiring Diagrams

A4004V / A6004V

2 CHANNEL MODE

BRIDGED CH1 CH2 CH3 CH4 BRIDGED

4~8 OHM BRIDGED BRIDGED
4~8 OHM

CH1 CH2 CH3 CH4

3 CHANNEL MODE
CH1 CH2 CH3 CH4
BRIDGED BRIDGED
BRIDGED
4~8 OHM

CH1 CH1 CH2 CH3 CH4

SPEAKER
2~8 OHM

CH2
SPEAKER
2~8 OHM

4 CHANNEL MODE

CH1 CH2 CH3 CH4

BRIDGED BRIDGED CH3
CH1 SPEAKER
SPEAKER 2~8 OHM
2~8 OHM
CH2 CH4
SPEAKER SPEAKER
2~8 OHM CH1 CH2 CH3 CH4 2~8 OHM

20
Wiring Diagrams

A4004V / A6004V

6 CHANNEL MODE

BRIDGED BRIDGED
4~8 OHM 4~8 OHM

CH2 CH3
SPEAKER SPEAKER
4~8 OHM CH1 CH2 CH3 CH4 4~8 OHM
BRIDGED BRIDGED

CH1 CH4
SPEAKER SPEAKER
4~8 OHM 4~8 OHM

CH1 CH2 CH3 CH4

: INDUCTOR LOW PASS FILTER : CAPACITOR HIGH PASS FILTER

COMPONENT VALUES FOR 6 dB PASSIVE CROSSOVER

FREQUENCY INDUCTOR CAPASITOR
80Hz 7.5 mH 470uF
100Hz 6.5 mH 330uF
120Hz 5.5 mH 330uF
150Hz 4mH 220uF

A8000V / A16000V
MONO MODE
SPEAKER

SUB WOOFER
2~8 OHM

21
Adjusting and Tunning

TURNING ON THE AMPLIFIER

The amplifier automatically turns on a few seconds after you turn your vehicle's ignition
switch to ACC or turn on your auto sound system (depending on how you have wired
the system). The POWER indicator on the top of the amplifier illuminates when the
amplifier is on.
Important: Your amplifier requires 20 amps or more of power from your vehicle's
battery during operation. To protect your battery from discharging, do not operate the
amplifier unless your vehicle is running.

Note: Your amplifier temporarily shuts down if it gets too hot, then restarts automatically
once it cools.

ADJUSTING THE AUDIO LEVEL

For the best performance, you must set GAIN (8V/0.2V) on the side of the amplifier to
adjust match the level of the audio signals that enter the amplifier from the source unit.

1. Use a screwdriver to turn GAIN (8V/0.2V) fully counterclockwise to 8V.

2. Turn the auto sound system's volume control to about one-third of its full range.
3. Adjust GAIN (8V/0.2V) to a comfortable listening level.
4. Turn up the auto sound system's volume control until the sound begins to distort.
Then immediately turn the volume down to a point just before where the distortion
began.
Caution Never turn up the auto sound system's volume control more than needed
to adjust the audio level (More than two thirds of its maximum volume).
5. Adjust GAIN (8V/ 0.2V) until the sound is at the maximum level you want the amplifier
to produce.
6. Adjust the auto sound system's volume control to a comfortable listening level.
FREQUENCY RESPONSE BASS BOOST ON
+ 20dB

+ 10dB
RESPONSE (dB)

0dB

- 10dB

- 20dB

- 30dB
10 50 100 500 1K 5K 20K 50K
FREQUENCY (Hz)

NOTE Raising the LPF frequency allows higher frequencies to reach the bass speakers
while blocking lower frequencies from midrange speakers. Lowering the LPF frequency
allows lower frequencies to reach the midrange speakers while blocking higher
frequencies from bass speakers.

22
Troubleshooting

Troubleshooting

SYMPTOMS CHECK POINTS CURE

NO SOUND Is the power Check fuses in amplifier.

LED illuminated ? Be sure Turn-on lead is connected
( NO ) Check signal leads. Check gain
control.
Check Tuner/Deck volume level.
Clean contacts on fuse holders.

Is the Diagnostic Check for speaker short or

LED illuminated ? ( YES ) Amplifier overheating.

AMP NOT No power to power wire Repair power wire or connections.

SWITCHING
ON No power to remote
wire with receiver on Check connections to radio.

Fuse broken Replace fuse.

NO SOUND Check Speaker Leads Inspect for short circuit or an

IN ONE open connection.
CHANNEL
Check Audio Leads Reverse Left and Right RCA inputs
to determine if it is occurring
before the amp.

AMP Check speaker load Be sure proper speaker load

TURNING OFF impedance impedance recommendations
MEDIUM/HIGH are observed.
VOLUME (If you use an ohmmeter to check
speaker resistance, please
remember that DC resistance and
AC impedance may not be the
same.)

STATUS Temperature shut down Turn radio down

LAMP ON
Speaker wires short Separate speaker wires and
insulate

23
 Warning / Disclaimer

WARNING
����������������������������������������������������

Investigate the layout of your automobile thoroughly before drilling or cutting any holes.
Take care when you work near gas tanks, gas lines, hydraulic lines, and electrical wiring.
Do not use the power amplifier unmounted. Attach the system securely to the automobile
to prevent damage, particularly in the event of an accident. Do not mount the system
so that the wire connections are unprotected or are subject to pinching or damage
from nearby objects.
The +12V DC power wire must be fused at the battery positive terminal connection.
Before making or breaking power connections at the system power terminals,
disconnect the +12V wire at the battery end. Confirm your radio/head unit and/or other
equiptment is turned off while connecting the input jacks and speaker terminals.
If you need to replace the power fuse, replace it only with a fuse identical to that
supplied with the system. Using a fuse of a different type or rating may result in damage to
this system which is not covered by the warranty.

Disclaimer
Specifications are subject to change with out notice.
For the most updated Specifications call Audiobahn,
your local Authorized Audiobahn Dealer,
or check the Audiobahn web site.
www.audiobahn.com

24
 Warranty
Audiobahn Consumer
Product Warranty Policy
�����������������������������������������������������

Audiobahn products are manufactured with the highest quality components and some of
the most advanced technology available. Because of this, we recommend that you have
your new products installed by an Authorized Audiobahn Dealer. (A list of Authorized
Audiobahn Dealers can be found on our web page).

Warranty Period: One year from the original date of purchase.

Warranty Coverage: This warranty covers manufacturer defects only. The warranty is
applicable to the original purchaser, and is non-transferable. You must provide a receipt
from an Authorized Audiobahn Dealer that shows the location of purchase, price paid,
and date of purchase.

(Products purchased by consumers from an Authorized Audiobahn Dealer outside the

United States are covered only by the Distributor of that specific country and are not
covered by Audiobahn).

Notes:
Complete subwoofer enclosures (Audiobahn will replace defective subwoofers,
plexiglass, or neon only. Do not send the entire enclosure, unless the enclosure is
defective itself. You must receive prior authorization and an RA# before sending in any
complete enclosure).

AUDIOBAHN DOES NOT WARRANTY ANY PRODUCTS NOT PURCHASED

THROUGH AN AUTHORIZED DEALER.
(A list of Authorized Audiobahn Dealers can be found on our web page).

AUDIOBAHN WARRANTIES DO NOT COVER THE FOLLOWING:

Any product not purchased from an Authorized Audiobahn Dealer (including Internet
dealers)

Damage caused by abuse, misuse, accident, water / flood, or theft (including any
cosmetic damage to the body of the product)

Damage caused by improper installation

Any cost or expense related to removal or reinstallation

Any unauthorized services

Any product that has the serial number removed, altered, or defaced

Subsequent damage to any other components

Pinched, cut, or stripped wires / terminals

Any product that is new, and/or found to be in working condition

L.E.D. indicators on electronics (Audiobahn will only replace L.E.D.(s) found to be

defective at the time of purchase)

25
 Warranty Continued
�������������������������������������������������������

How to receive warranty service: Contact your local Authorized Audiobahn Dealer, or call Audiobahn at
(800) 488-8595 between the hours of 9:00 AM and 5:00 PM PST.

If you are having problems with your system, we recommend you check the product carefully and
thoroughly to confirm that the product truly has a manufacturer defect; as opposed to abuse, or other
components in the system causing the failure. This might include having an Authorized Audiobahn
Dealer look at the product to confirm the source of the problem. Any product found to have a
manufacturer defect will be replaced with a new piece of the same or similar model, or repaired at the
discretion of Audiobahn. Any product found to have no manufacturer defect will be returned to the sender
at their cost.

You must acquire a Return Authorization Number ( #) prior to returning ANY product to
Audiobahn. That Return Authorization Number (RA#) must be prominently and clearly marked on the
outside of the shipping carton, or product delivery will be refused (no exceptions will be made).

Please note: All shipping and handling (to and from) charges will be the sole responsibility of the
consumer.

Please record and keep your Return Authorization Number (RA#) in the event that further communication
is required.

Return Authorization Number (RA#): ______________________________

Date product was sent: ______________________________

Contact Information

Audiobahn Headquarters
114 South Berry St.
Brea, CA 92821
Phone (800)488-8595 Fax. (714)988-0433
Pacific Coast Time : 9am-5pm Mon. - Fri.
[email protected]

26