Scribd
Upload
246 views

Mini Tesla Coil Project

This document describes the working of a mini Tesla coil circuit called a slayer exciter. [1] It uses basic components like a transistor, resistor, and coils to generate a high voltage, high frequency electromagnetic field from a low DC voltage source. [2] When a fluorescent bulb is brought near the secondary coil, it glows brightly due to the transmitted electrical energy without the use of wires. [3] Wireless power transmission could help reduce dependence on batteries and make power distribution more efficient by eliminating power losses over long transmission lines.

Uploaded by

abinash
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
246 views

Mini Tesla Coil Project

This document describes the working of a mini Tesla coil circuit called a slayer exciter. [1] It uses basic components like a transistor, resistor, and coils to generate a high voltage, high frequency electromagnetic field from a low DC voltage source. [2] When a fluorescent bulb is brought near the secondary coil, it glows brightly due to the transmitted electrical energy without the use of wires. [3] Wireless power transmission could help reduce dependence on batteries and make power distribution more efficient by eliminating power losses over long transmission lines.

Uploaded by

abinash
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

lMINI TESLA

COIL:

Introduction:
Tesla Coil is a circuit that generates a ​high
• ​A

voltage, high frequency ​electromagnetic field


even from a low voltage DC source.

• ​Slayer
exciter is simplest version of tesla coil
as slayer exciter requires only some basic
components(transistor,resistor, a primary coil
and a secondary coil) and also it is does not
produce much heat because it consumes less
power.

TOOLS USED:

ENAMELED COPPER WIRE(L=20


1. ​

M, D=.3mm). ​2. ​Transistor –


2N2222A. 3​ . ​RESISTANCE –
22K OHM. 4​ . ​KEY. 5​ . ​CELL –
9V. 6​ . ​PVC PIPE (12CM). 7​ .
CONNECTING WIRE.
WORKING
PRINCIPAL:

The slayer exciter is a high voltage


stepup transformer, with an output
voltage high enough to create
such an electric field, which
lightens up the fluorescent bulb.

How does it work:


Ckt. Diagram

1. ​Turning the circuit on, R drives the base of the


transistor Q ​2. ​Q turns on and drives current into the
primary of the transformer. The current is limited by
the limited available base current. 3​ . ​The created
magnetic field drives the
secondary of the transformer. ​4. ​The secondary
voltage wants to grows large.
But the tiny stray capacitance on the output resists the
change, although very small, against the rise of the
output end and so in return the voltage on the other
end of the transformer goes down, pulling the base of
the transistor low. 5​ . ​Diode D prevents the base voltage
to fall more
than 0.7V below ground, which in return pushes the
output end of the secondary high. ​6. ​The transistor
turns off and so the magnetic
field starts to reduce. ​7. ​The base voltage rises
again and Q turns on
and the cycle repeats.

Block diagram:
Circuit diagram:
Result:

Whenever we bring a fluorscent bulb close to the


secondary winding, after switching on the circuit, The
bulb glows producing high intensity light as bulb glows
when supplied ac power. ​It is the transmission of
electrical energy from power source to electric
load, over a distance, without usage of wires or
cables.

The key parameter in transmitting power is


efficiency​. Conventional methods of transmitting
power don’t have high capacity of transmitting
energy with less power loss.

Long range communication is possible which is


impossible with conventional method, is achieved
with this technology.

Conclusion:
Doing this project we conclude that with the help of
this kind of technology, wireless power transmission
can be made possible and this technology will help us
in eradicating the hazardous uses of electrical wires
and Huge power losses in transmission. ​It is
envisaged that wireless energy would be really
accomplished with the advantage of easy
implementation and cost effective i.e., cost of
transmission and distribution overhead would
become less. In the long run, this could reduce
our society’s dependence on batteries, which are
currently heavy and expensive.
WIRES... A BURDEN!!!
FUTURE WORK:

Wireless electricity transmission can change the world of


electricity and electrical engineering. The power loss due
to transmission lines can be reduced(no I square R loss).
Less amount of wires would be used in any circuit.

You might also like