Introduction to J2534 and

Flash Reprogramming

Provided by:

Drew Technologies
Background

The days of diagnosing and repairing automobiles without a laptop beside you are quickly
fading. Newer vehicles include a large number of onboard computers that are each
dedicated to performing specific tasks. Common onboard computers in newer vehicle
include the Engine Control Module (ECM), Transmission Control Module (TCM), Fuel
Injection Control Module (FICM), Anti-lock Brake System (ABS), Body Control Module
(BCM) and numerous other control modules to manage every electronic system from
power door locks to crash data.

Each onboard computer is programmed at the factory with software enabling it to perform
certain tasks. Inside the ECM is software containing hundreds or even thousands of

Drew Technologies, Copyright 2007 1

parameters to control spark, fuel, idle, cruising, emissions, economy, drivability, and
performance. Likewise, a TCM will have software to control how the transmission and
torque converter function. Sometimes, after the vehicle is shipped from the automaker,
updates are released to improve emissions, fuel economy, drivability, performance, or
specific bugs in the original software that have caused warranty issues. Updating this
software can be a proactive fix because often it will resolve problems that a customer
hasn’t reported or noticed yet..

The practice of updating software in these modules is more commonly known as flash
reprogramming. At new car dealerships, flash reprogramming is relatively straight forward
because service technicians are connected to the automaker and have the expensive,
specialized dealer service tools dedicated to reprogramming. The independent repair shops
have faced a more difficult challenge because most shops typically service more than one
make of automobiles. This increases the complexity, cost, and training required to operate
dozens of different factory service tools.

J2534 – A Solution Arrives

In 2000, the Environmental Protection Agency had been watching this issue and decided to
take action. The EPA requested a standard be developed within the SAE that led to

Show Desktop.scf
J2534, a mandated specification to which automakers who sell vehicles in
the United States must conform. The original J2534 specification was later updated to
J2534-1 in order to support all automakers. The EPA mandate requires automakers to
support aftermarket repair shops with J2534-1 flash reprogramming for any emissions
related computer modules on a vehicle that can be reprogrammed by a new car dealership.
This mandate took effect for all 2004 and newer vehicles, but many automakers have
decided to offer J2534-1 support for vehicles older than 2004 and some vehicles as early
as model year1996.

J2534-1 is a system devised of two independent parts: subscription software and a J2534-
1 compliant PassThru vehicle interface. The subscription software comes directly from the
automaker, runs on your shop PC or laptop, and can either be web-based or CDbased. The
subscription fees are charged differently for each automaker. Some automakers such as GM
charge an annual fee for full access, while others have options for paying: per-vehicle, daily,
weekly, monthly, or annually. Many of these services also include bonus features beyond flash
reprogramming. FMP from Ford lets repair shops reprogram transponder keys, and other
automakers are beginning to support diagnostic functionality. Figure 1 shows the website for
each automaker’s service and fees.

Hardware
The second part of the system is a J2534-1 compliant PassThru vehicle interface. This box
or cable acts as a gateway between the vehicle’s onboard computers and the technician’s
personal computer. It translates messages from the PC into the protocols used by the
automobile and vice versa. A Drew Tech J2534 tool is pictured in Figure 2 to give you an
idea of what a PassThru interface looks like.

Drew Technologies, Copyright 2007 2

Common PassThru devices connect your PC to the vehicle using USB, serial, Ethernet, or
wireless. The easiest to configure is probably USB, but Ethernet has the longest range and
highest performance. You can double the distances on USB connections by adding a hub
between your PC and PassThru tool. Wireless has also become popular with both
Bluetooth and 802.11 options being offered by different tool vendors. The 802.11
technology offers a higher bandwidth and distance range, but typically costs more than a
Bluetooth option. Figure 3 illustrates the benefits of each connection type and highlights
the option best for each characteristic. The CarDAQ-Plus from Drew Technologies
(www.drewtech.com) and the E-Flash from ATS (www.automotivetestsolutions.com) are
currently the only PassThru tools offer Ethernet, USB, and an upgrade path to 802.11
wireless all from one device.

There are a number of PassThru tools for sale in the market, all at different prices with
different features, performance, and customer support. The primary function of a PassThru
device is to support the automaker’s subscription service for reprogramming. Picking a
device that is fully compliant to J2534-1 is important, but many bonus features may make
certain brands more attractive. Some offer additional features such as generic scan tool
software, enhanced diagnostics software, and analog scope inputs.

Performing J2534 reprogramming requires computer knowledge and experience. The technician
will need to operate a laptop or desktop, the PassThru device, and the reprogramming software.
Operation will also require a good high-speed connection to the Internet such as DSL, Cable, or
T1.

Non-compliant Devices
Because J2534-1 is an SAE standard, all PassThru tools should be the same; but in reality
not all devices are fully compliant to J2534-1 or work with all vehicles. You should shop
carefully when picking a device, and look at functionality and compliance before shopping
on price alone. Be sure to get one that is guaranteed by the manufacturer to be fully
compliant and that has been validated by the automakers you plan to service. None of the
automakers sell their own PassThru tool, but many recommend products that they have
validated internally.

The SAE is planning to publish a conformance test. The conformance test has been named
J2534-3, and will be applied to J2534-1 devices. The numbering is confusing, but
remember that J2534-1 is the standard for reprogramming, and J2534-3 tests for
conformance to J2534-1. There is even a J2534-2 published spec, but that doesn’t apply to
EPA reprogramming requirements. Once the J2534-3 test has been published, a tool
manufacturer should be able to certify that their products pass the J2534-3 test. The
J2534-3 conformance test has not been published yet, so for now you should look for
devices that have been validated by the automakers. Many of the automaker websites in
Figure 1 have a list of recommended devices. Of all vendors offering J2534 tools, at the
writing of this article, Drew Technologies has been validated by more automakers than
any other.

ROI

Drew Technologies, Copyright 2007 3

The initial purchase price for getting acquainted with J2534 will pay back over time and
generate revenue. Although each price is different, the average software charge from each
automaker is approximately $25 per flash over time. The average revenue for shop service
tickets that include a reflash is $150. At four tickets per month, the shop would pay $100
in software fees and make back $600 in gross revenue. That equals $6000 per year in
revenue. You will spend around $2000 on J2534 equipment up-front. If you use the tools
you purchase and offer these services, the cost will pay itself back in a very short time.

Onboard VS Offboard
Onboard programming means that you are reprogramming the vehicle’s computer while it
is installed in the vehicle and offboard reprogramming means you are removing the
computer from the vehicle and reprogramming it from a bench top with a special cable
and power supply. Figure 4 shows what an offboard reprogramming bench may look like.
There are some pre-made offboard cables available for certain vehicles, but there are
literally dozens of different types of onboard computers, connectors, and pin diagrams.

Unless you have a specific reason to remove the onboard computer from the vehicle and
reprogram it from an offboard bench, or unless you have advanced experience with J2534,
you should leave the onboard computer installed in the vehicle when reprogramming.
Many of the J2534-1 applications may try to reprogram more than one module when you
select a reprogramming operation, and the only way you can guarantee all necessary
modules are reprogrammed and the software matches is by reprogramming the computer
while it is installed in the car. This is the way the automakers intend you to use their
software, and for that reason onboard programming is preferred. There are some special
cases where offboard reprogramming becomes more advantageous, but you must first
have knowledge of that specific processor and configuration to understand the possible
risks of reprogramming a module outside its normal environment.

Constant Power
Whether you are reprogramming onboard or off board, you must be sure that the power
supplied to the module does not drop below 11.5 - 12 volts. Some reprogramming
operations with the key-on will turn on cooling fans, fuel pumps, and other components
that will cause the battery to drain faster than normal. Instead of pulling fuses to prevent
the battery drain, it is easier and more practical to have the vehicle connected to a charger
or jump pack. During reprogramming there is a risk of having the operation fail if voltage
falls below the proper operating voltage. Sometimes a failed operation can be recovered,
but there is a chance that failed reprogramming could ruin the control module. To mitigate
this risk, put a high quality battery charger on the vehicle if you are reprogramming
onboard or use a good bench top power supply if you are reprogramming offboard.

Updated Calibrations
One important step in the service process is determining of a vehicle needs a calibration
update. The J2534 subscription software will usually tell you if an update is needed, but
sometimes only after you pay the subscription fee. That makes it tough to check for
updates without encountering some type of fee. If you want to find out before you
purchase the subscription, you can usually find a table, PDF, or matrix on the
manufacturer’s website telling you if there are updated calibrations. For example, Chrysler

Drew Technologies, Copyright 2007 4

has a flash matrix available at http://techauthority.com under the J2534 Flash availability
section. For GM vehicles, you can visit http://calid.gm.com and type in the VIN or part
number to learn if updates are available. Figure 5 shows GM’s CalID site. At
www.motorcraftservice.com, there is a link in the reprogramming section called Latest
Calibration Information. That link will open an Excel sheet that lists all of the PCM tag
codes, and shows what updates are available. You should note that a calibration update
may be available even if there is not a specific TSB calling for it.

Using J2534-1
Because each automaker has different software, you should become comfortable with one
automaker’s service before you start on the next. Start by reprogramming a vehicle you
have regular access to before accepting vehicles from walk-in customers. Take your time
and follow the steps at the automaker’s website. If you have questions, call the automaker’s
customer support number or your PassThru tool vendor. J2534 reprogramming requires a
PC and Internet, and the technician reflashing cars should be computer savvy. If you are
uncomfortable using a PC and the Internet, you may want to seek out an independent
trainer in your area and attend a J2534 class.

When you provide reprogramming service to a customer there are several things you
should consider. First, reprogramming is a service that cannot be reversed. If you update
the calibration in the customer’s car, there is no method to put the old calibration back in.
There is a chance the new calibration will change noticeable characteristics in the way the
customer’s car drives. It may raise or lower the idle, change the shifts or idle speed control,
or other settings meant to solve a warranty issue, economy issue, or emissions issue. There
is no way to revert back if the customer doesn’t like one of the new settings.
This is not something that happens often, but you should always disclaim this to the customer
beforehand and ask the customer to waive any liability to you.

The duration of a reprogramming operation will vary between manufacturers and models.
The shortest time may be less than a minute, with some of the abnormally long
reprogramming operations exceeding an hour. The average is just under 15 minutes for the
entire process. Before you start, remember you should be certain that you have a good
battery in the vehicle or an external charger

Although unlikely, there is also a chance that the reprogramming operation on the vehicle
could fail. It could fail due to faulty wiring/modules, low battery, or for some other reason.
Some older vehicles, especially Class2 GM vehicles, may not be recoverable if you lose
power to the module and the process fails. If the reprogramming does fail, it will take
more time to update the vehicle. In the worst case scenario a new module may need to be
ordered for the vehicle.
If a reprogramming event fails, immediately retry the operation without disconnecting the
J2534 tool. If a battery charger or jump pack was not used the first time, connect one and
turn it on before you retry. Usually a failed attempt will complete successfully the second
time. If you cannot get the reprogramming operation to succeed after repeated attempts, call
the automaker’s support number to find out if there is any other way to recover the module.
If all else fails, the module might be reprogrammable offboard.

Drew Technologies, Copyright 2007 5

Ford
The FMP (Ford Module Programming) application is a user-friendly J2534 service. Visit
www.motorcraftservice.com and download the reprogramming software. You’ll need to
be connected to the Internet during the entire reprogramming operation. The cost to use
FMP is $24.95 for a 72 hour period or $59.95 per month, so it is a very inexpensive way
to start learning J2534-1. For this price you gain access to the latest calibrations, can
perform module initialization (PATS), and can adjust certain parameters on Ford, Lincoln
and Mercury vehicles. The Ford application works on almost all OBD2 Ford vehicles that
are 1996 or newer, . Ford modules typically reprogram quickly, and recover easily if you
have a reprogramming failure. Figure 6 shows the J2534 configuration screen in FMP, and
Figure 7 shows the J2534 programming screen.

GM
Currently, General Motors vehicles can be reprogrammed using the TIS/SPS subscription
service. This service is DVD-based, and DVD updates are mailed frequently through the
year when you purchase the service. The DVD-based kit, part number OTC-3625-17, can be
purchased for just under $1000 and includes one year of updates. Instructions for
configuring TIS for a J2534 PassThru device should be available from your J2534 tool
vendor.

You can reprogram as many vehicles as you want for the subscription cost. GM’s new
service called TIS2WEB, already in use by GM dealerships, will be released to the
aftermarket at the end of 2006. With TIS2WEB the aftermarket repair shop can get instant
access to updates without buying a TIS DVD-based subscription. The GM software works
on almost all OBD2 GM vehicles, covering most 1996 and newer models. When
reprogramming older GM vehicles, be very careful not to interrupt the operation. Some of
the older modules may not be easily recoverable if reprogramming fails. Newer CAN
vehicles do not seem to have this problem, and overall the risk is small as long as you are
careful (i.e. don’t unplug the equipment in the middle of a reprogramming operation.)

Chrysler
The Chrysler J2534 service works similarly to Ford’s FMP. Visit www.techauthority.com
to subscribe and download the reprogramming software. You’ll need an Internet connection
initially, to download the calibration file, but it’s not required during actual
reprogramming. The service fee is $20 per day, or $200 per month. For this price, you get
access to not only the calibrations, but also the service information on the website. Once
downloaded, you will be prompted to enter the vehicle information so you have access to
the latest calibrations. Chrysler’s application works on most OBD2 vehicles, again 1996
and newer. Figure 8 shows the J2534 programming with Chrysler.

Honda
Honda and Acura require a base ServiceExpress membership plus a subscription to their
CD-based J2534 reprogramming service. Visit techinfo.honda.com to see a matrix of
reprogrammable vehicles, subscribe, and download the reprogramming software. The
basic membership costs $20 for a 3-day subscription, $50 per month, or $250 per year. The
reprogramming CDs are an additional fee of $300 per year. The ServiceExpress

Drew Technologies, Copyright 2007 6

membership includes access to TSB’s and online service information. Honda mails
updates through the year, and you won’t need an Internet connection during
reprogramming. Although the 1996 Acura RL and 1997 Prelude can be flashed, neither
Honda nor Acura have widespread reprogramming support until model year 2002.

Toyota
Toyota’s J2534 software is CD-based like many others, and can be purchased from
techinfo.toyota.com. From the CD you can pick the calibration and update the vehicle. A
screenshot from Toyota’s Calibration Update Wizard is shown in Figure 9.

Many other manufacturers offer J2534 subscription services, as listed in Table 1.

Although each one has a unique user interface, they all follow the same basic principles.
They are designed to allow you to perform updates to the calibration software inside newer
vehicles. After using a few different versions, you will become comfortable with the
reprogramming process.

Figure 1 OEM table

J2534 Subscription Services
Information about services available from automakers

J2534 reprogramming costs Website one 1-3

use day monthly yearly
BMW 30 250 2500 http://www.bmwtechinfo.com/
Mini http://www.minitechinfo.com/
Porsche 100 http://techinfo.porsche.com/
Chrysler, Jeep,
Dodge 20 200 1500 http://www.techauthority.com/
Ford, Lincoln,
Mercury 24.95 59.95 599.95 http://www.motorcraft.com/
Land Rover http://www.landrovertechinfo.com/
Volvo**** 84 http://www.volvotechinfo.com/
General Motors
Brands* 995 http://www.gmtechinfo.com/
Acura, Honda** 300 http://www.serviceexpress.honda.com/
Isuzu 1968 http://www.isuzutechinfo.com/
Kia / Hyundai http://www.kiatechinfo.com
Mazda 24.95 59.95 599.95 http://www.mazdatechinfo.com/
Mercedes 925 http://www.startekinfo.com/
Mitsubishi 19.95 249.95 1449.95 http://www.mitsubishitechinfo.com/
Nissan 19.95 http://www.nissan-techinfo.com
Subaru*** 75 http://techinfo.subaru.com
Toyota, Lexus,
Scion 55 http://techinfo.toyota.com/
Volkswagen 50 200 1000 www.ebahn.com/vw
Audi 50 200 1000 www.ebahn.com/audi

Drew Technologies, Copyright 2007 7

* GM is moving to Web based TIS2WEB system at the end of 2006 with different purchase options
available
** Honda requires that you have a Service Express Membership to gain access to reprogramming
instructions and TSBs. Service express is $20 for a 3-day subscription, $50 per month, or $250 per year
*** Subaru charges $75 per CD that contains all calibrations. There could be up to 4 updates per year
**** Volvo charges $84 per 3-day period, plus around $30 per calibration

Figure 2 CarDAQ-Plus

Figure 3

characteristic
Plug and Play Yes No No No No
Protected from ground
loops, static, and
surges No Yes Yes Yes Yes
32 300
Distance Limitation 15 feet 45 feet 300 feet Feet* feet*
Max Speed 11Mbps 0.125Mbps* 100Mbps 1Mbps 54Mbps
Available on most new
laptops Yes No Yes No Yes
* Approximation, may
vary

Figure 4 Bench Programming

Drew Technologies, Copyright 2007 8

Figure 5

Figure 6 FMP Webflash J2534 Figure 7 FMP reprogramming screen

Configurations

Drew Technologies, Copyright 2007 9

Figure 8 DCX Reprogramming

Figure 9 Toyota Reprogramming Screen

Drew Technologies, Copyright 2007 10

Drew Technologies, Copyright 2007 11