Orange - CMYK 88%Y 66%M

Grey - CMYK 44% Black

Gear Motors
Group 1, 2 and 3 l Technical Information

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
2 GEAR MOTORS I TECHNICAL INFORMATION

History of revisions

Date Page Changed Rev.

28, June 2010 - First edition A

24, Feb 2011 1, 2, 12, 44 Covers to blue color, Turolla brand name, Biofluids deleted. B

30, Sept 2013 ALL Layout and options lists C

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 3

Index

General Information
4 Overview 42 Integral relief valve and Anti-cavitation check valve – SNM2JN
5 Features and Benefits 43 Outrigger bearing assembly – SNM2NN
5 Motor Displacements 47 Dimensions
6 Determination of Nominal Motor Size 47 SNM2NN, SNU2NN – 01DA, 01FA and 01BA
48 SNM2NN, SNU2NN – 02DB and 02AA
System Requirements 49 SNM2NN, SNU2NN – 03CA
7 Pressure 50 SNM2NN, SNU2NN–04DB/05DB and 04AA/05AA
7 Speed 51 SNM2NN, SNU2NN, SKU2NN – 06SA, 06GA
8 Hydraulic Fluids
8 Temperature and Viscosity Group 3 Gear Motors
9 Filtration 52 Motor design
9 Filters 52 SNM3NN
9 Selecting a filter 52 SNU3NN
9 Reservoir 53 Technical data
10 Line Sizing 54 Model code
10 Motor Shaft Connection 59 Motor performance graphs
11 Motor Shaft Load Data Form 62 Flange, shaft and port configurations
12 Motor Life 63 Shaft and flange availability
64 Ports dimensions
Group 1 Gear Motors 67 Anti-cavitation check valve – SNM3GN
13 Motor Design 68 Dimensions
13 SKM1NN 68 SNM3NN, SNU3NN – 01FA, 01DA and 01BA
13 SKU1NN 69 SNM3NN, SNU3NN – 02FA, 02DB and 02AA
13 SNU1NN 70 SNM3NN, SNU3NN – 03FB and 03BB
14 Technical Data 71 SNM3NN, SNU3NN – 06AA
15 Model Code 72 SNM3NN, SNU3NN – 07BC, 07SA and 07GA
19 Motor performance graphs
21 Flange, shaft and port configurations
22 Shaft options
23 Integral relief value - SKM1IN
24 Ports dimensions
25 Dimensions
25 SKM1NN, SKU1NN, SNU1NN – 01BA
26 SKM1NN, SKU1NN – 02BB, 02FA
27 SKM1NN, SKU1NN – 06GA and 06SA

Group 2 Gear Motors

28 Motor design
28 SNM2NN
28 SNU2NN
28 SKU2NN
29 Technical data
30 Model code
36 Motor performance graphs
38 Flange, shaft and port configurations
39 Shaft options
40 Port dimensions
41 Integral relief valve – SNM2IN
42 Anti-cavitation check valve – SNM2GN

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
4 GEAR MOTORS I TECHNICAL INFORMATION

General information

Overview
The Turolla Gear Motors is a range of peak performance fixed displacement hydraulic motors available in three different
frame sizes: Group 1, Group 2 and Group 3, all as uni- and bidirectional version.

Constructed of a high strength extruded aluminum body with aluminum rear cover and aluminum front flange, all motors
are balanced for exceptional efficiency and designed to ensure an excellent starting torque and, in the bidirectional version,
to guarantee the ability to work with high back pressure and extremely low system pressure.

The flexibility of the range in each frame size combined with the high efficiency and low starting torque makes the Turolla
Gear Motors ideal for a wide range of applications sectors including on- and off-highway hydraulic fan drive systems, turf
care, road bildge, fork lifts and municipal.
All the unidirectional motors have the same construction of the correspondent pump as well but, with inlet and outlet
positioned at the opposite side for the same rotation.

Some representatives of gear motors:

SKM1NN 06SA SNM3NN 01BA SNM3NL 07SA

SNM2NN 9JDB SNU2NN 06SA SNU2NN 06GA

© 2013 Turolla ™. All rights reserved.

Turolla accepts no responsibility for possible errors in catalogs, brochures and other printed material. Turolla reserves the right to alter its products without prior notice. This also applies to products already
ordered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners.
Danfoss, Turolla, Turolla OpenCircuitGear, OpenCircuitGear, Fast Lane and PLUS+1 are trademarks of the Danfoss Group.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 5

Features and Benefits

• Three groups of frame sizes (Group 1, 2 and 3)
• Displacements from 2.6 to 90 cm3/rev [from 0.158 to 5.49 in3/rev]
• Available in uni- and bidirectional version for all the frame sizes, displacements and
configurations
• Rated pressure up to 250 bar [3625 psi]
• Back pressure capability up to 250 bar [3625 psi]
• Speeds up to 4000 min-1 (rpm) for Group 1 and 2, and up to 2500 min-1 (rpm) for Group 3
• SAE, ISO and DIN mounting flanges and shafts
• Available with integrated relief valve in the Group 2 frame size and integrated
anti-cavitation valve in Group 2 and Group 3 frame sizes.

Motor Displacements

Quick reference chart for unidirectional motor models (Group 1, 2 and 3)

300
SKU1NN
SNU1NN
Rated pressure bar

250
SKU2NN
200 SNU2NN
SNU3NN
150

100

50

0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95

Displacement cm3/rev

Quick reference chart for bidirectional motor models (Group 1, 2 and 3)

300
SKM1NN
250 SNM2NN
Rated pressure bar

SNM3NN
200

150

100

50

0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95

Displacement cm3/rev

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
6 GEAR MOTORS I TECHNICAL INFORMATION

Determination of Nominal Motor Size

Use these formulas to determine the nominal motor size for a specific application.

Based on SI units Based on US units

Input flow: V V • n
g•n g
Q = l/min Q = [US gal/min]
1000 • ηv 231 • ηv

Output torque:
Vg • ∆p • ηm
V
g • ∆p • η
M = N•m M = m [lbf•in]
20 • π 2 • π

Output power: M • n Q • ∆p • η M • n Q • ∆p • η
t t
P = = kW P = = [hp]
9550 600 63 025 1714

Variables
SI units [US units]

Vg = Displacement per revolution cm3/rev [in3/rev]

po = Outlet pressure bar [psi]
pi = Inlet pressure bar [psi]
∆p = po – pi (system pressure) bar [psi]
n = Speed min-1 (rpm)
ηv = Volumetric efficiency
ηm = Mechanical efficiency
ηt = Overall efficiency (ηv • ηm)

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 7

System Requirements

Pressure Time versus pressure

Peak pressure is the highest intermittent pres-
Peak pressure
sure allowed.
The relief valve overshoot (reaction time) deter-
mines peak pressure. It is assumed to occur for less
Rated pressure
than 100 ms.

Pressure
The illustration to the right shows peak pressure in
relation to rated pressure and reaction time (100
ms maximum).

Rated pressure is the average, regularly Reaction time (100 ms max)

occurring operating inlet pressure that should
yield satisfactory product life. The maximum Time
machine load at the motor shaft determines rated P005 006E

pressure.

System pressure is the differential between the inlet and outlet ports. It is a dominant
operating variable affecting hydraulic unit life. High system pressure, resulting from high
load at the motor shaft, reduces expected life. System pressure must remain at, or below,
rated pressure during normal operation to achieve expected life.

Back pressure is the average, regularly occurring operating outlet pressure that should
yield satisfactory bidirectional motor life. The hydraulic load demand downstream
of the motor determines the back pressure. Unidirectional motors cannot work with
back pressure and the maximum back pressure allowed is 5 bar [72 psi] rated and 7 bar
[101 psi ] as peak.

Case Drain Pressure is the regularly occurring case drain line pressure that should
yield satisfactory bidirectional motor life. It is recommended to design the case
drain piping connecting the case drain direct to the tank in order to keep the case
drain pressure as low as possible. The max. continuous case drain pressure allowed is
5 bar [72 psi] rated and 7 bar [101 psi] as peak.

Speed versus pressure

Speed
Rated
Maximum speed is the limit recommended by
Turolla for a particular gear motor when operating
at rated pressure. It is the highest speed at which
normal life can be expected.
Pressure

The lower limit of operating speed is the Operating

minimum speed. It is the lowest speed at which
normal life can be expected.
P1
envelope
The minimum speed increases as operating
system pressure increases. When operating under
higher pressures, a higher minimum speed must
be maintained, as illustrated to the right. 0
N1 N2 Max
Speed
N1 = minimum speed at low pressure
N2 = minimum speed at rated pressure

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
8 GEAR MOTORS I TECHNICAL INFORMATION

Hydraulic Fluids
Ratings and data for gear motors are based on operating with premium hydraulic fluids
containing oxidation, rust, and foam inhibitors. These fluids must possess good thermal and
hydrolytic stability to prevent wear, erosion, and corrosion of internal components. They include:
• Hydraulic fluids following DIN 51524, part 2 (HLP) and part 3 (HVLP) specifications
• API CD engine oils conforming to SAE J183
• M2C33F or G automatic transmission fluids
• Certain agricultural tractor fluids

Use only clean fluid in the motor and hydraulic circuit.

Caution

Never mix hydraulic fluids.

Please see Turolla publication Hydraulic Fluids and Lubricants Technical Information, L1021414 for
more information. Refer to publication Experience with Biodegradable Hydraulic Fluids Technical
Information, L1021903 for information relating to biodegradable fluids.

Temperature and Viscosity

Temperature and viscosity requirements must be concurrently satisfied.
Use petroleum/mineral-based fluids.

High temperature limits apply at the inlet port of the motor. The motor should run at or below the
maximum continuous temperature. The peak temperature is based on material properties. Don’t
exceed it.

Cold oil, generally, doesn’t affect the durability of motor components. It may affect the ability of
oil to flow and transmit power. For this reason, keep the temperature at 16°C
[60 °F] above the pour point of the hydraulic fluid.

Minimum (cold start) temperature relates to the physical properties of component materials.

Minimum viscosity occurs only during brief occasions of maximum ambient temperature and
severe duty cycle operation. You will encounter maximum viscosity only at cold start. During this
condition, limit speeds until the system warms up. Size heat exchangers to keep the fluid within
these limits. Test regularly to verify that these temperatures and viscosity limits aren’t exceeded.
For maximum unit efficiency and bearing life, keep the fluid viscosity in the recommended
viscosity range.

Fluid viscosity Temperature

Maximum (cold start) 1000 [4600] Minimum (cold start) -20 [-4]
mm2/s °C
Recommended range 12-60 [66-290] Maximum continuous 80 [176]
[SUS] [°F]
Minimum 10 [60] Peak (intermittent) 90 [194]

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 9

Filtration
Filters
Use a filter that conforms to Class 22/18/13 of ISO 4406 (or better).
It may be on the motor outlet (discharge filtration) or inlet (pressure filtration).

Selecting a filter
When selecting a filter, please consider:
• contaminant ingression rate (determined by factors such as the number of actuators used in
the system)
• generation of contaminants in the system
• required fluid cleanliness
• desired maintenance interval
• filtration requirements of other system components

Measure filter efficiency with a Beta ratio (βX):

• for discharge filtration with controlled reservoir ingression, use a β35-45 = 75 filter
• for pressure filtration, use a filtration with an efficiency of β10 = 75

βx ratio is a measure of filter efficiency defined by ISO 4572. It is the ratio of the number of particles greater than a given
diameter ( “X“ in microns) upstream of the filter to the number of these particles downstream of the filter.

Fluid cleanliness level and βx ratio

Fluid cleanliness level (per ISO 4406) Class 22/18/13 or better
βx ratio (discharge filtration) β35-45 = 75 and β10 = 2
βx ratio (pressure filtration) β10 = 75
Recommended inlet screen size 100 – 125 µm [0.0039 – 0.0049 in]

The filtration requirements for each system are unique. Evaluate filtration system capacity by
monitoring and testing prototypes.

Reservoir
The reservoir provides clean fluid, dissipates heat, removes entrained air, and allows for fluid
volume changes associated with fluid expansion and during all system operating modes. A
correctly sized reservoir accommodates maximum volume changes during all system operating
modes. It promotes deaeration of the fluid as it passes through, and accommodates a fluid dwell-
time between 60 and 180 seconds, allowing entrained air to escape.

Minimum reservoir capacity depends on the volume required to cool and hold the oil,
allowing for expansion due to temperature changes. A fluid volume of one to three times the
motor output flow (per minute) is satisfactory. The minimum reservoir capacity is 125% of the fluid
volume.

Put the return-line below the lowest expected fluid level to allow discharge into the reservoir for
maximum dwell and efficient deaeration. A baffle (or baffles) between the return and suction lines
promotes deaeration and reduces fluid surges.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
10 GEAR MOTORS I TECHNICAL INFORMATION

Line Sizing
Choose pipe sizes that accommodate minimum fluid velocity to reduce system noise, pressure
drops, and overheating. This maximizes system life and performance.

The line velocity should not exceed the values in this table:

Maximum line velocity

Inlet 2.5 [8.2]
Outlet m/s [ft/sec] 5.0 [16.4]
Return 3.0 [9.8]

Most systems use hydraulic oil containing 10% dissolved air by volume. Over-aeration is the
result of the flow-line restrictions. These include inadequate pipe sizes, sharp bends, or elbow
fittings, causing a reduction of flow line cross sectional area. This problem will not occur if rated
speed requirements are maintained, and reservoir size and location are adequate.

Motor Shaft Connection Motor shaft connection

Shaft options for gear motors include tapered,
splined, parallel or Turolla tang shafts. Pilot cavity

Plug-in drives, with a splined shaft, can

impose severe radial loads when the mating Mating spline
spline is rigidly supported. Increasing spline
clearance does not alleviate this condition.

Use plug-in drives if the concentricity between

the mating spline and pilot diameter is within
0.1 mm [0.004 in]. Lubricate the drive by
flooding it with oil. A three-piece coupling
minimizes radial or thrust shaft loads.

Ø 0.1 [0.004]
P101 002E

Caution

In order to avoid spline shaft damages it is recommended to use carburised and hardened steel
couplings with 80-82 HRA surface hardness.

Allowable radial shaft loads are a function of the load position, load orientation, and operating
pressure of the hydraulic motor. All external shaft loads have an effect on bearing life, and may
affect motor performance.

In applications where external shaft loads can not be avoided, minimize the impact on the motor
by optimizing the orientation and magnitude of the load. Avoid thrust loads in either direction.
Please contact Turolla, if continuously applied external radial or thrust loads occur.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 11

Motor Shaft Load Data Form

Photocopy this page and fax the complete form to your Turolla representative for an as-
sistance. This illustration shows a motor with counterclockwise orientation:

Radial load (RL)

90o
a
α

Axial load Inlet port

(AL) 180 o 0o

270o

RL

Application data
Item Value Based on SI or US units
Motor displacement  cm3/rev  in3/rev
Rated system pressure
 bar  psi
Peak pressure
Motor shaft rotation  left  right
Motor minimum speed
min-1 (rpm)
Motor maximum speed
Radial load RL N  lbf
Angular orientation of radial load to inlet port α degree
Axial load AL N  lbf
Distance from flange to radial load a  mm  in

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
12 GEAR MOTORS I TECHNICAL INFORMATION

Motor Life
Motor life is a function of speed, system pressure, and other system parameters (such as
fluid quality and cleanliness).

All Turolla gear motors use hydrodynamic journal bearings that have an oil film
maintained between the gear/shaft and bearing surfaces at all times. If the oil film
is sufficiently sustained through proper system maintenance and operating within
recommended limits, long life can be expected.

B10 life expectancy number is generally associated with rolling element bearings. It does
not exist for hydrodynamic bearings.

High pressure impacts motor life. When submitting an application for review, provide
machine duty cycle data that includes percentages of time at various loads and speeds.
We strongly recommend a prototype testing program to verify operating parameters
and their impact on life expectancy before finalizing any system design.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 13

GROUP 1 GEAR MOTORS

Motor Design
SKM1NN 06SA
SKM1NN
SKM1NN is the Group 1 bidirectional motor
available in the whole displacements range from
2.6 up to 12 cm3/rev [from 0.158 up to 0.732 in3/
rev].

Configurations include European and SAE flanges

and shafts (Code 01BA, 01DA, 02BB, 02FA, 06GA,
06SA).

SKU1NN
SKU1NN is a Group 1 unidirectional motor available in the whole displacements
range from 2.6 up to 12 cm3/rev [from 0.158 up to 0.732 in3/rev]. The SKU1NN motor
construction is derived from the correspondent pump SKP1NN.
Configurations include European and SAE flanges and shafts (Code 01BA, 01DA, 02BB,
02FA, 06GA, 06SA).

SNU1NN SNU1NN 01BA (cut-away)

SNU1NN is a Group 1 unidirectional motor
available in a limited displacements
range from 2.6 up to 7.8 cm3/rev [from
0.158 up to 0.464 in3/rev]. The SNU1NN
motor construction is derived from the
correspondent pump SNP1NN.
Configurations include European flange
and shaft (Code 01BA).

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
14 GEAR MOTORS I TECHNICAL INFORMATION

Technical Data
Technical data for Group 1 gear motors
Frame size
2,6 3,2 3,8 4,3 6,0 7,8 010 012
cm3/rev 2.62 3.14 3.66 4.19 5.89 7.59 9.94 12
Displacement
[in3/rev] [0.158] [0.195] [0.231] [0.262] [0.366] [0.463] [0.607] [0.732]
SKM1NN (a standard, bidirectional motor)
270 270 270 270 250 220 180 150
Peak pressure
[3915] [3915] [3915] [3915] [3625] [3190] [2610] [2175]
bar 250 250 250 250 230 200 160 130
Rated pressure
[psi] [3625] [3625] [3625] [3625] [3335] [2900] [2320] [1895]
250 250 250 250 230 200 160 130
Back pressure
[3625] [3625] [3625] [3625] [3335] [2900] [2320] [1895]
Minimum speed min-1 1000 1000 1000 800 800 800 800 800
Maximum speed (rpm) 4000 4000 3000 3000 2000 2000 2000 2000
SKU1NN (a standard, unidirectional motor)
270 270 270 270 250 220 170 140
Peak pressure
bar [3915] [3915] [3915] [3915] [3625] [3190] [2465] [2030]
[psi] 250 250 250 250 230 200 150 120
Rated pressure
[3625] [3625] [3625] [3625] [3335] [2900] [2175] [1740]
Minimum speed min-1 1000 1000 1000 800 800 800 800 800
Maximum speed (rpm) 4000 4000 3000 3000 2000 2000 2000 2000
SNU1NN (a standard, unidirectional motor)
270 270 270 270 190 180
Peak pressure
bar [3915] [3915] [3915] [3915] [2755] [2610]
[psi] 250 250 250 250 170 160
Rated pressure –
[3625] [3625] [3625] [3625] [2465] [2320]
Minimum speed min-1 1000 1000 1000 800 800 800
Maximum speed (rpm) 4000 4000 3000 3000 2000 2000
All
kg 1.02 1.14 1.18 1.20 1.30 1.39 1.55 1.65
Weight
[lb] [2.26] [2.51] [2.60] [2.65] [2.87] [3.06] [3.42] [3.64]
Moment of inertia of x 10-6 kg•m2 5.1 5.7 6.4 7.1 9.3 11.4 14.6 17.1
rotating components [x 10-6 lbf•ft2] [121.0] [135.2] [151.9] [168.5] [220.7] [270.5] [339.4] [405.8]

1 kg•m2 = 23.68 lb•ft2

Caution

The rated and peak pressure mentioned are for motors with flanged ports only. When threaded ports are required a de-
rated performance has to be considered. To verify the compliance of an high pressure application with a threaded ports
pump apply to a Turolla representative.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 15

Product Code
Model Code
A B C D E F G H I J K L M N 0
/

A Family

SNU1NN Unidirectional gear motor

SKU1NN High torque unidirectional gear motor
SKM1NN Standard bidirectional gear motor
SKM1IN Bidirectional motor with relief valve
SKM1WL Bidirectional motor+Relief valve;Anti-shock valve;Radial drain

B Displacement C Rotation

2,6 2.62 cc L Left hand

3,2 3.14 cc R Right hand
3,8 3.66 cc B Bidirectional
4,3 4.19 cc
5,5 5,23 cc
6,0 5.89 cc
7,8 7.59 cc
010 9.94 cc
012 12.0 cc

D Project version (value representing

a change to the initial project)

N Std Version of Project

6 Short version -Special

E Mounting flange

01 European 4 bolt flange with pilot Ø25,4 mm

02 European 4 bolt flange with pilot Ø30 mm
06 SAE A-A 2 bolt flange with pilot Ø50,8 mm
** SAE A pilot Ø82,55+2 holes (**Special Option)

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
16 GEAR MOTORS I TECHNICAL INFORMATION

A B C D E F G H I J K L M N 0
/

F Drive gear

BA Taper 1:8-M7-Key2,41 SKP1

BB Taper 1:8-M10x1-Key 3
DB Splined Z15-m0,75-alfa 30°-L14-Dr60,5
DC Splined B12x9-L14-flange protrusion sb22-Z6-m1,60-alfa 30°
FA Parallel Ø12-Thread M10x1-Key 3
GA Parallel Ø12,7-Key 3,2
SA SAE spline J498-9T-20/40 Flat Root Side FIT-L15
SG SAE spline J498-8T-16/32 -shaft version 6

G Rear cover

P1 Standard cover for unidirectional motors

M1 Standard cover for motors drain M12x1,5
M2 Cover with drain 1/8" Gas
M3 Cover with drain 1/4" Gas
M6 Cover with drain 7/16-20UNF-2B
MH Cover with drain M12x1,5 ISO6149
I1 Cover for unidirectional motors with relief valve
L6 Cover motor with side drain in vertical axis 7/16-20UNF-2B
V1 Cover for bidirectional motors with relief valve with drain 1/4 Gas
W6 Cover motor with relief and antishock valve

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 17

A B C D E F G H I J K L M N 0
/

H Inlet size I Outlet size

E3 9/16-18UNF
B1 8x30xM6
E4 3/4-16UNF
B2 13x30xM6
E5 7/8-14UNF
C1 8x26xM5 F2 1/4 GAS
C2 12x26xM5 F3 3/8 GAS
C3 13,5x30xM6 F4 1/2 GAS
D3 M14x1,5 H2 10xM12x1,5-ISO6149
D5 M18x1,5 H4 12xM16x1,5-ISO6149
D7 M22x1,5 H5 12xM18x1,5-ISO6149
13,5xM22x1,5-
H7
J Ports Pos & Spec Body ISO6149

N Std from catalogue

K Seals

N Standard NBR seal

VITON seals + special backing ring-
H
special for SKU1NN

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
18 GEAR MOTORS I TECHNICAL INFORMATION

A B C D E F G H I J K L M N 0
/

L Screws

N Std screws
B GEOMET screws

M Set valves
NNN No valve
V** Integral relief valve pressure setting
**For details go to page 23

N Type of mark

N Standard Turolla Marking

Standard Turolla Marking+Customer
A
Code
Z Without Marking

O Mark position

N Std Marking position (on top)

Special Marking position on the
A
bottom

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 19

Motor performance graphs

The graphs on the next pages provide typical inlet flow and output power for Group 1 motors at various working pressures.
Data were taken using ISO VG46 petroleum /mineral based fluid at 50 °C [122 °F] (viscosity = 28 mm2/s [132 SUS]).

SKM1NN/2,6 motor performance graph SKM1NN/3,2 motor performance graph

SKM1NN/3,8 motor performance graph SKM1NN/4,3 motor performance graph

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
20 GEAR MOTORS I TECHNICAL INFORMATION

SKM1NN/6,0 motor performance graph SKM1NN/7,8 motor performance graph

SKM1NN/010 motor performance graph SKM1NN/012 motor performance graph

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 21

Flange, shaft and port configurations

Flange, shaft and port configurations for SKM1NN and SKU1NN motors
Code Flange Shaft Port

European 01, 4-bolts European

01BA Taper 1:8
pilot Ø 25.4 mm [1.0 in] in + pattern

European 02, 4-bolts German standard

02BB Taper 1:8
pilot Ø 30 mm [1.181] in X pattern

European 02, 4-bolts Parallel European

02FA
pilot Ø 30 mm [1.181] 12 mm [0.472 in] in + pattern

SAE A-A Parallel Threaded SAE

06GA
2-bolts 12.7 mm [0.5 in] O-ring boss

SAE A-A SAE A-A Threaded SAE

06SA
2-bolts 9-teeth splined O-ring boss

Flange, shaft and port configuration for SNU1NN motor

Code Flange Shaft Port

European 01, 4-bolts European

01BA Taper 1:8
pilot Ø 25.4 mm [1.0 in] in + pattern

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
22 GEAR MOTORS I TECHNICAL INFORMATION

Shaft options
Group 1 motors are available with a variety of splined, parallel, and tapered shaft ends. Not all
shaft styles are available with all flange styles.

Shaft availability and nominal torque capability

A B C D E F G H I J K L M N 0
/

Shaft Mounting flange code with maximum torque

Code Description 01 02 06
BA Taper 1:8 25 [221] - -
BB Taper 1:8 - 50 [442] -
DB Splined Z15-m0,75-alfa 30°-L14 - 35 [309] -
DC Splined B12x9-L14-Z6-m1,60 30 [265] - -
FA Parallel 12 mm [0.47 in] - 24 [212] -
GA Parallel 12.7 mm [0.50 in] - - 32 [283]
SA SAE spline J 498-9T-20/40DP - - 34 [301]
SG SAE spline J498-8T-16/32 (version 6 - - 34 [301]
only)

Recommended mating splines for Group 1 splined output shafts should be in

accordance with SAE J498 or DIN 5482. Turolla external SAE splines are flat root side fit
with circular tooth thickness reduced by 0.127 mm [0.005 in] in respect to class 1 fit. The
external DIN splines have an offset increased by 0.1 mm [0.004 in]. These dimensions are
modified in order to assure a clearance fit with the mating spline.

Other shaft options may exist. Contact your Turolla representative for availability.

Caution

Shaft torque capability may limit allowable pressure. Torque ratings assume no external
radial loading. Applied torque must not exceed these limits, regardless of stated pressure
parameters. Maximum torque ratings are based on shaft torsional fatigue strength.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 23

Integral relief valve – SKM1IN Valve schematic diagram

Turolla offers an optional integral relief
valve integrated in the Group 1 motors rear
cover. It is drained internally and directs all
the flow from the motor inlet to the outlet
when the inlet pressure reaches the valve
setting.

The tables below show applicable variant

codes for ordering motors with integral relief
valve. Refer to Model Code, page 18 for more
information.

Integral relief valve rear cover cross section Pressure vs flow

[psi] bar With mineral oil at 26 mm2/s
400
[5000]
300
[4000]

[3000] 200

[2000]
100
[1000]
Inlet
Drain MINIMUM VALVE SETTING
0 0
10 20 30 40
P101 016 l/min

0 [2] [4] [6] [8] [10]

[US gal/min]

Variant codes for ordering integral relief valve

A B C D E F G H I J K L M N 0
/ V

M Variant code (left part) M Variant code (right part)

Motor speed for RV setting Pressure setting bar Pressure setting bar
Code Code Code
min-1 (rpm) [psi] [psi]
A not defined A no setting O 90 [1305]
C 500 B no valve P 100 [1450]
E 1000 C 18 [261] Q 110 [1595]
F 1250 D 25 [363] R 120 [1740]
G 1500 E 30 [435] S 130 [1885]
K 2000 F 35 [508] T 140 [2030]
I 2250 G 40 [580] U 160 [2321]
L 2500 J 150 [2175] V 170 [2466]
M 2800 K 50 [725] W 180 [2611]
N 3000 L 60 [870] X 210 [3046]
O 3250 M 70 [1015] Z 250 [3626]
N 80 [1160]

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
24 GEAR MOTORS I TECHNICAL INFORMATION

Ports dimensions
Available ports for Group 1 motors
B C D E F

45o

g x d e f

h y
i (4 holes min. full thd. z (4 holes min. full thd.
20 mm [0.787 in] deep) 20 mm [0.787 in] deep)

Bidirectional motor ports

SKM1NN bidirectional motor ports dimensions (all frame sizes)

Port type B C D E F
Port dimensions g h i x y z d e f
13 30 12 26
Inlet/Outlet M6 M5 M18x1.5 ¾–16UNF–2B 3/₈ Gas (BSPP)
[0.512] [1.181] [0.472] [1.024]
Drain M12x1.5 M12x1.5 M12x1.5 / –20UNF–2B
7 16 / Gas (BSPP)
1 8

Unidirectional motor ports

SNU1NN, SKU1NN unidirectional motor ports dimensions

Port type B C D E F
Port dimensions g h i x y z d e f
Inlet 8 [0.315] M14x1.5 9/₁₆ –18UNF–2B
2,6
Outlet 13 [0.512] M18x1.5 ¾–16UNF–2B
Inlet 8 [0.315] M14x1.5 9/₁₆ –18UNF–2B
3,2
Outlet 13 [0.512] M18x1.5 ¾–16UNF–2B
Inlet 8 [0.315] M14x1.5 9/₁₆ –18UNF–2B
3,8
Outlet 13 [0.512] M18x1.5 ¾–16UNF–2B
Inlet 8 [0.315] M14x1.5 9/₁₆ –18UNF–2B
Frame size

4,3
Outlet 13 [0.512] 30 12 26 M18x1.5 ¾–16UNF–2B 3/8 Gas
M6 M5
Inlet 13 [0.512] [1.181] [0.472] [1.024] M18x1.5 9/₁₆ –18UNF–2B (BSPP)
6,0
Outlet 13 [0.512] M18x1.5 ¾–16UNF–2B
Inlet 13 [0.512] M18x1.5 9/₁₆ –18UNF–2B
7,8
Outlet 13 [0.512] M18x1.5 ¾–16UNF–2B
Inlet 13 [0.512] M18x1.5 9/₁₆ –18UNF–2B
010
Outlet 13 [0.512] M18x1.5 ¾–16UNF–2B
Inlet 13 [0.512] M18x1.5 9/₁₆ –18UNF–2B
012
Outlet 13 [0.512] M18x1.5 ¾–16UNF–2B

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 25

Dimensions

SKM1NN, SKU1NN, SNU1NN – 01BA

Standard porting drawing for 01BA
01BA mm
[in]
29 [1.14] B max
12.4 [0.488] A ±0.50 [0.020]
1:8
14.4 [0.583] 5.2 [0.205] Distance from front flange
Ø 25.4 -0.041 [1.0 -0.0016 ]
-0.0008

to cone reference diameter

4.2 [0.165] 16.5 [0.65] 68 ±0.25 [2.68 ±0.010]

(34.3 max)
Pilot width body width

[1.35]
-0.020

Ø 9.82 [0.387]

[0.85 ±0.020]
21.6 ±0.50
A

[1.03]
26.2
88.1 [3.47] max

74.5 [2.93] max

[2.83]
(71.9)
(53.8 max)

[1.8]
45.7
M7-6g

[2.12]
Cone reference diameter
10.8 ±0.50 [0.425 ±0.020]

C/c
M12x1.5-6H
(min full thd 10 [0.394] deep) E/e Ø7.2 - 8 Drain port
Ø 0.75 X
[.283- .315]
D/d ±0.20 [0.008] 52.4 [2.06]
Recommended
tightening torque: 7-12 Nm
69.4 [2.73] max
A-A
0 0
2.41 -0.025 [0.0949 -0.0098 ]

5.5 +0.15 +0.0059

-0.25 [0.217 -0.0098 ]

For unidirectional motors no case drain hole into the rear cover.

SKM1NN – 01BA dimensions

Type (displacement) 2,6 3,2 3,8 4,3 6,0 7,8 010 012
40.5 41.5 42.5 43.5 46.75 50.0 54.5 58.5
A
[1.594] [1.634] [1.673] [1.713] [1.841] [1.969] [2.146] [2.303]
Dimension
85.0 87.0 89.0 91.0 97.5 104.0 113.0 121.0
B
[3.346] [3.425] [3.504] [3.583] [3.839] [4.094] [4.449] [4.764]
C/c 12 [0.472]
Inlet/Outlet D/d 26 [1.024]
E/e M5

For unidirectional SNU1NN, SKU1NN dimensions, see Ports dimensions, page 24.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
SKM1NN/3,2BN01BAM1C2C2NNNN/NNNNN
01BA SKU1NN/4,3LN01BAP1C2C2NNNN/NNNNN 25 N•m [221 lb•in]
SNU1NN/3,8RN01BAP1F3F3NNNN/NNNNN
For further details on ordering, see Model Code, pages 15-18.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
26 GEAR MOTORS I TECHNICAL INFORMATION

SKM1NN, SKU1NN – 02BB, 02FA

Standard porting drawing for 02BB and 02FA
02BB 02FA mm
[in]
B max
35 [1.378]

8.0 [0.315] Distance from front flange

15.5 [0.610] to cone reference diameter
7.0 [0.276]
31.5 [1.240]
Pilot width
Recommended 15.75 [0.620] 16.5 [0.650] 8.3 [0.327] Distance from front
(32.1 [1.264] max)
tightening 68.0 ±0.25
flange to shoulder
torque: 10-16 Nm [23.677 ±0.010 ]
1: 8 A ±0.50 [±0.02] body width 11.7 [0.461]

24.5 [0.965]
X

M10 x 1-6g
A

B
88.2 [3.472] max

74.5 [2.933] max

(73.0 [2.874])
(56.1 [2.209] max)

48.5 [1.909]
Cone reference diameter
]

10.8 ±0.50[0.425 ±0.020]

M10x1-6g

A
-0.0008
[1.181 -0.0016

-0.001]
[0.472 +0.0
Recommended
tightening
Ø13.95 [0.549]

C/c torque: 10-16 Nm

-0.020
30.0 -0.041

12.0 -0.018
+0.0
M12x1.5-6H
E/e (min full thd 10 [0.394] deep)
Drain port

D/d ±0.20 [±0.08] Ø 6.7-7.5

Ø 0.75 [0.0295] X
[0.264-0.295]
A-A B-B
0 0 56.0 [2.205] +0.0
3.0-0.030 [0.118 -0.001]
+0.0
3.0 -0.030 [0.118 -0.001]
70.9 [2.791] max

7.5 +0.25 +0.010

-0.15 [0.295 -0.006 ]
+0.05 +0.002
13.2 -0.20 [0.520 -0.008 ]

For unidirectional motors no case drain hole into the rear cover.

SKM1NN – 02BB and 02FA dimensions

Type (displacement) 2,6 3,2 3,8 4,3 6,0 7,8 010 012
40.5 41.5 42.5 43.5 46.75 50.0 54.5 58.5
A
[1.594] [1.634] [1.673] [1.713] [1.841] [1.969] [2.146] [2.303]
Dimension
85.0 87.0 89.0 91.0 97.5 104.0 113.0 121.0
B
[3.346] [3.425] [3.504] [3.583] [3.839] [4.094] [4.449] [4.764]
C/c 12 [0.472]
Inlet/Outlet D/d 26 [1.024]
E/e M5

For unidirectional SKU1NN dimensions, see Ports dimensions, page 24.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
SKM1NN/010BN02BBM1C2C2NNNN/NNNNN
02BB 50 N•m [442 lb•in]
SKU1NN/6,0LN02BBM1C2C2NNNN/NNNNN
SKM1NN/6,0BN02FAM1C2C2NNNN/NNNNN
02FA 24 N•m [212 lb•in]
SKU1NN/6,0LN02FAM1C2C2NNNN/NNNNN
For further details on ordering, see Model Code, pages 15-18.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 27

SKM1NN, SKU1NN – 06GA and 06SA

Standard porting drawing for 06GA and 06SA

06GA 06SA mm
[in]
27.0 [1.063] B max
7.9 [0.311]
Distance from front flange to shoulder 103.4 [4.071] max
27.0 [1.063]
6.0 [0.236] Distance from front
19.1 82.55 [3.258]
Pilot width flange to shoulder
[0.752] 7.9 [0.311]
X A ±0.50 [0.020] R 32.1 [1.26] max
19.1 [0.752]
8.0 [0.315]
15.6 [0.614]
A
80.2 [3.157] max

74.5 [2.933] max

10.2-10.8 [.402-.425]

12.344 -0.127 [0.486 -0.05 ]

10.8 ±0.50 [0.425 ±0.020]

[0.500 -0.001 ]

0
]

0
[2.0 -0.002
0

12.7 -0.025

C/c Straight thread 7/16-20UNF-2B

50.8 -0.050

0
0

O-Ring boss Drain port

0

Ø 0.75 [0.030] X

68.0 ±0.25 [2.677 ±0.010]

A-A Splined:
body width SAE J498-9T-20/40DP
13.94-14.20
[0.549-0.559] Flat root side fit
Circular tooth thickness:
0.127 [0.005]
0 0 less than class 1 fit
3.2 -0.025 [0.126 -0.126 ]

For unidirectional motors no case drain hole into the rear cover.

SKM1NN – 06GA and 06SA dimensions

Type (displacement) 2,6 3,2 3,8 4,3 6,0 7,8 010 012
45 46 47 48 51.25 54.5 59 63.5
A
[1.771] [1.811] [1.850] [1.889] [2.017] [2.145] [2.322] [2.500]
Dimension
89.5 91.5 93.5 95.5 102 108.5 117.5 125.5
B
[3.523] [3.602] [3.681] [3.759] [4.015] [4.271] [4.625] [4.940]
Inlet/Outlet C/c ¾–16UNF–2B, THD 14.3 [0.563] deep

For unidirectional SKU1NN dimensions, see Ports dimensions, page 24.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
SKM1NN/6,0BN06GAM6E4E4NNNN/NNNNN
06GA 32 N•m [283 lb•in]
SKU1NN/4,3RN06GAP1E3E4NNNN/NNNNN
SKM1NN/012BN06SAM6E4E4NNNN/NNNNN 34 N•m [301 lb•in]
06SA
SKU1NN/3,2LN06SAP1E3E4NNNN/NNNNN
For further details on ordering, see Model Code, pages 15-18.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
28 GEAR MOTORS I TECHNICAL INFORMATION

GROUP 2 GEAR MOTORS

Motor Design SNM2NN 9JDB (cut-away)

SNM2NN
SNM2NN is the group 2 bidirectional motor
available in the whole displacements range
from 6 up to 25 cm3/rev [from 0.37 up to
1.538 in3/rev].
Configurations include European and SAE
flanges and shafts (Code 01BA, 01FA, 01DA,
02AA, 02DB, 03CA, 04AA/05AA, 04DB/05DB,
06GA, 06SA).
SNU2NN 06SA (cut away)

SNU2NN
SNU2NN is the group 2 unidirectional
motor available in the displacements
range from 8 up to 25 cm3/rev [from
0.513 up to 1.538 in3/rev]. The SNU2NN
motor construction is derived from the
correspondent pump SNP2NN.
Configurations include European and SAE
flanges and shafts (Code 01BA, 01FA, 01DA,
02AA, 02DB, 03CA, 04AA/05AA, 04DB/05DB, 06GA, 06SA).

SKU2NN
SKU2NN is the Group 2 unidirectional motor available in the displacements range from
8 up to 25 cm3/rev [from 0.513 up to 1.538 in3/rev]. The SKU2NN motor construction is derived
from the correspondent pump SKP2NN. Configuration includes SAE flange and shaft only (Code
06SA).

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 29

Technical data
The table below details the technical data for Group 2 gear motors based on the model and displacement configuration.

Technical data for Group 2 gear motors

Frame size
6,0* 8,0 011 014 017 019 022 025
cm3/rev 6.0 8.4 10.8 14.4 16.8 19.2 22.8 25.2
Displacement
[in3/rev] [0.36] [0.513] [0.659] [0.879] [1.025] [1.171] [1.391] [1.538]
SNM2NN (bidirectional motor)
280 280 280 280 260 230 200 180
Peak pressure
[4060] [4060] [4060] [4060] [3770] [3335] [2900] [2610]
250 250 250 250 230 210 180 160
Rated pressure bar [psi] [3625] [3625] [3625] [3625] [3335] [3045] [2610] [2320]
250 250 250 250 230 210 180 160
Outlet back pressure
[3625] [3625] [3625] [3625] [3335] [3045] [2610] [2320]
Minimum speed 700 700 700 700 500 500 500 500
min-1 (rpm)
Maximum speed 4000 4000 4000 4000 4000 3500 3500 3500
SNU2NN (unidirectional motor)
280 280 280 260 230 200 180
Peak pressure
[4060] [4060] [4060] [3770] [3335] [2900] [2610]
bar [psi]
250 250 250 230 210 180 160
Rated pressure –
[3625] [3625] [3625] [3335] [3045] [2610] [2320]
Minimum speed 600 600 600 500 500 500 500
min-1 (rpm)
Maximum speed 3500 3500 3500 3000 3000 3000 2500
SKU2NN (unidirectional motor)
280 280 280 260 230 200 175
Peak pressure
[4060] [4060] [4060] [3770] [3335] [2900] [2815]
bar [psi]
250 250 250 230 210 180 160
Rated pressure –
[3625] [3625] [3625] [3335] [3045] [2610] [2320]
Minimum speed 600 600 600 500 500 500 500
min-1 (rpm)
Maximum speed 3500 3500 3500 3000 3000 3000 2500
All (SNM2NN, SNU2NN, SKU2NN)
2.4 2.5 2.7 2.9 3.0 3.1 3.2 3.3
Weight kg [lb]
[5.3] [5.5] [5.5] [6.3] [6.5] [6.7] [7.0] [7.3]
Moment of inertia of x 10-6 kg•m2 26.5 32.4 38.4 47.3 53.3 59.2 68.1 74.1
rotating components [x 10-6 lb•ft2] [629] [769] [911] [1122] [1265] [1405] [1616] [1758]
Theoretical flow at l/min 24 33.6 43.2 50.4 50.4 57.6 68.4 75.6
maximum speed [US gal/min] [6.3] [8.9] [11.4] [13.3] [13.3] [15.2] [18.0] [20.0]
1 kg•m2 = 23.68 lb•ft2

* Before chosing this frame size, please apply to Turolla technical department.

Caution

The rated and peak pressure mentioned are for motors with flanged ports only.
When threaded ports are required a de-rated performance has to be considered. To
verify the compliance of an high pressure application with a threaded ports pump
apply to a Turolla representative.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
30 GEAR MOTORS I TECHNICAL INFORMATION

Product Code
Model Code
A B C D E F G H I J K L M N 0
/

A Family

SEM2DN Low Cost Gr2 Bidir.Motor-int.drain SNM2IN Gr2 Bidir.Motor+Int.drain RV

SEM2NL Low Cost Gr2 Bidirec.Motor-vert.drain SNM2JN Gr2 Bid.Motor+Int.drain RV+Anticav.Check Valve
SEM2NN Low Cost Gr2 Bidirec.Motor SNM2NC Gr2 Bidir.Motor-Cover Ports-Ax.drain
SHM2GL Hi.Press.Gr2 Bid.Mot.+Antic.Check Val-Vert.drain SNM2NL Gr2 Bidir.Motor-Vert.drain
SHM2IN Hi.Press.Gr2 Bidir.Motor+Int.drain RV SNM2NN Gr2 Bidir.Motor
SHM2NL Hi.Press.Gr2 Bidirec.Motor-Vert.drain SNM2SN Gr2 Bidir.Motor+by-pass electric valve-Special
SHM2NN Hi.Press. Gr2 Bidirec.Motor SNU2EN Gr2 Unidir.Motor+Ext.drain RV
SHU2GN Hi.Press. Gr2 Unidir.Motor+Anticav.Check valve SNU2GN Gr2 Unidir.Motor+Anticav.Check Valve
SHU2NN High Press. Gr2 Unidir.Motor Gr2 Unidir.Motor-In./Out. on Cover+Anticav.Check
SNU2GC
SKU2NN Big shaft GR2 Unidir.Motor Valve
SNU2IN Gr2 Unidir.Motor+Int.drain RV
SNM2DN Gr2 Bidir.Motor-Int.Drain
Gr2 Unidir.Motor+Int.drain RV+Anticav.Check
SNM2FL Gr2 Bidir.Motor+Break.Valve-Vert.drain-Special SNU2JN
Valve
SNM2FN Gr2 Bidir.Motor+Break.Valve-Special
SNU2NC Gr2 Unidir.Motor-In.-Out.on cover
SNM2GC Gr2 Bidir.Motor+Anticav.Check Val.-Ax.drain
SNU2NN Gr2 Unidir.Motor
SNM2GL Gr2 Bidir.Motor-Anticav.Check Val.-vert.drain
SNU2QN Gr2 Unid.Motor-Ext.drain RV+Anticav.Check Valve
SNM2GN Gr2 Bidir.Motor-Anticav.Check Valve
Gr2 Unidir.Motor-Break.Valve as Anticav.Valve-
SNU2TN
SNM2IL Gr2 Bidir.Motor+Int.drain RV-Vert.drain Special

B Displacement

5,5 5,5 cc -Special 011 10,8 cc 021 21,0 cc -Special

6,0 6,0 cc -Special 012 12,0 cc -Special 022 22,8 cc
8,0 8,4 cc 014 14,4 cc 025 25,2 cc
9,0 9,0 cc -Special 017 16,8 cc
9,5 9,5 cc -Special 019 19,2 cc

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 31

A B C D E F G H I J K L M N 0
/

D Project version (value representing

C Rotation a change to the initial project)

B Bidirectional N Std Version of Project

L Unidirectional Left hand 2 Std Big-Shaft - Special Unbalanced
Unidirectional Right Precharged seal on cover-Special
R 4
hand heavy-duty applications
6 Short version - Special
E Mounting flange

01 pilot Ø36,5+4 holes

02 pilot Ø80+4 holes
03 pilot Ø52+O-ring+4 holes through body
04 pilot Ø50+2 holes through body
05 pilot Ø50+2 holes through body
06 SAE A pilot Ø82,55+2 holes
B2 pilot Ø80+4 holes+special shaft seal slot - Special
L5 pilot Ø52 spigot Diameter+O-Ring+4 holes through body - Special
Q2 pilot Ø80+4 holes+fastening holes Ø10,5mm- Special
91 Outriger Bearing Type 01+taper shaft 1:8-M12x1,25-Key4
92 Outriger Bearing Type 02+taper shaft 1:5-M12x1,25-Key3
94 Outriger Bearing Type 04+taper shaft 1:5-M12x1,25-Key3
9A Outriger Bearing Type 01+taper shaft 1:8-M12x1,25-Key3.2
9D Outriger Bearing Type 01+parallel shaft Ø15-Key4
9F Outriger Bearing Type 02+taper shaft 1:5-M14x1,5-Key4+special shaft seal RZB
Outriger Bearing Type 04+taper shaft 1:5-M12x1,25-Key3 + 4 M10 assembly thd
9G
holes "HELI-COIL- Special
9H Outriger Bearing Type 06+taper shaft 1:8-M12x1,25-Key4
9J Outriger Bearing Type 06 with parallel shaft Ø3/4 (Ø19.05 mm)
9L Outriger Bearing Type 01 parallel shaft Ø22 pilot Ø50,8
9M Outriger Bearing Type 01 parallel shaft Ø18 pilot Ø36,5

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
32 GEAR MOTORS I TECHNICAL INFORMATION

A B C D E F G H I J K L M N 0
/

F Drive gear

AA Taper 1:5-M12x1,25-Key 3
AC Taper 1:5-M14x1,5-Key 4
AD Taper 1:5-M12X1,25-Key 3-Drive - Special for Version 6
B1 Taper 1:8-M12x1,25-Key 4/6 lowered
BA Taper 1:8-M12x1,25-Key 4
BB Taper 1:8-M12x1,25-Key 4/3,2
BJ Taper 1:8-M12x1,25-Key 4/3 black steel
CA Tang 8x17,8xL6,5 FR03
CF Tang 8x Ø17,46xL9,6-Special
DA Spline DIN 5482 B17x14-L10
DB Spline DIN 5482 B17x14-L14
Spline DIN 5482 B17x14-L14+rear spline DIN 5482 17x14-L14
DL
SC32…_2 - Special
EC Spline DIN 5480 W20x1,25xz14-9g - Special
FA Parallel Ø15-L30+Key 4x25
GA Parallel SAE Ø15,875-L23,8-Key 4x18
GB Parallel SAE Ø15,875-L50,8-Key 4x40
GC Parallel SAE Ø17,46-L24,4-Key 3/16x3/16xL20 - Special
SA Spline SAE J498-9T-16/32
SB Spline SAE J498-11T-16/32 -Special only for Version 2
SE Spline SAE J498-9T-16/32+M6 thd hole
SF Spline SAE J498-9T-16/32-reinforced fillet
SG Spline SAE J498-11T-16/32-Special only for Version 2
SI Spline SAE J498-11T-16/32-Special only for Version 2
TC Spline SAE 13T-20/40-Special

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 33

A B C D E F G H I J K L M N 0
/

G Rear cover

Cover for unidirec. motors front SAE ports: Inlet 3/4-16UNF- LS Cover motor-drain at 22° left 7/16-20UNF-2B drive gear side
C7
2B;Outlet 3/4-16UNF-2B Cover motor-drain in vertical axis 1/4 Gas for flange typo 03
LT
Cover for unidirectional motors with relief valve - external drive gear side
E1
drain 3/8 Gas Cover motor-drain in vertical axis 9/16-18UNF-2B drive gear
LX
Cover for unidirectional motors with Relief Valve ext.drain side
E6
3/4-16UNF-2B LZ Cover motor-drain in vertical axis 1/4 Gas drive gear side
F1 Cover motor per braking valve and drain 1/4 Gas M1 Std cover motor drain 1/4 Gas driven side
F6 Cover motor per braking valve and drain 9/16-18UNF-2B M3 Std cover motor drain 1/4 Gas for flange typo 03
G1 Cover motor front ports:Inlet 1/2 G;Outlet 1/2 G;Drain 1/4 G M4 Std cover motor drain 9/16-18UNF-2B for flange typo 03
Cover motor front ports:Inlet 7/8-14UNF;Outlet M6 Std cover motor drain 9/16-18UNF-2B
G6
7/8-14UNF;Drain 9/16-18UNF M7 Std cover motor-drain 1/4 Gas drive side
I1 Cover for unidirectional motors with RV Special intermediate motor flange tipo 01-drain 1/4 Gas -
M8
J1 Cover motor per braking valve with drain in vertical axis 1/4 G Special
Cover motor per braking valve with side drain in vertical axis P1 Std cover for unidirectional motors
J6
9/16-18UNF-2B P3 Std cover for unidirectional motors for flange typo 03
L1 Cover motor-drain in vertical axis 1/4 Gas Cover motor-Electric-piloted distributor+by-pass-drain
S1
L3 Cover motor-drain in vertical axis 1/4 Gas for flange typo 03 vert.1/4 G-In-Out 1/2 G - Special
L6 Cover motor-drain in vertical axis 9/16-18UNF-2B Cover motor per braking valve used as anti-cavitation valve
T1
L7 Cover motor-drain at 22° left 7/16-20UNF-2B internal drain - Special
L8 Cover motor-drain in horizontal axis 9/16-18UNF-2B drain left V1 Cover motor per RV with drain 1/4 Gas
LC Cover motor-drain in horizontal axis 1/4 Gas right side V2 Cover motor per RV with drain vertical axis 1/4 Gas driven side
LD Cover motor-drain in horizontal axis 1/4 Gas left side V6 Cover motor per RV with drain 9/16-18UNF-2B
LE Cover motor-drain in horizontal axis M12x1,25 ISO 6149 Cover motor per RV with drain vertical axis 9/16-18UNF-2B
V7
LF Cover motor-drain in horizontal axis M12x1,5 right side driven side
Cover motor-drain in horizontal axis 9/16-18UNF-2B drain
LH
right

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
34 GEAR MOTORS I TECHNICAL INFORMATION

A B C D E F G H I J K L M N 0
/

H Inlet size I Outlet size

NN Without inlet F3 3/8 GAS

B3 13,5x30xM6 in X
F4 1/2 GAS
B5 15x35xM6
B6 15x40xM6 F5 3/4 GAS
B7 20x40xM6 F6 1 GAS
BB 27x55xM8 H5 M18x1,5-ISO6149
C2 12x26xM5
H7 M22x1,5-ISO6149
C3 13,5x30xM6
C4 15x35xM6 DXK(+) H8 M27x2-ISO6149
C5 13,5x40xM8 H9 M33x2-ISO6149
C6 20x40xM6 DXK(+)
C7 20x40xM8 M1 12x17,48x38,1xM6
C8 23,5x40xM8
CS 13,5x30xM6 (2 holes)
M2 12x17,48x38,1xM8
CV 20x40xM8 (2 holes at 30°) M3 18,5x17,48x38,1xM8
CX 20x40xM8 (2 holes)
CY 20x40xM8 (3 holes) M5 25/20x52,37x26,19xM10
D4 M16x1,5 MB 12x38,1x17,48xM8(=)
D5 M18x1,5 MC 18,5x47,63x22,23xM6(=)
D7 M22x1,5 MD 18,5x47,63x22,23xM8(=)
D9 M26x1,5 ME 18,5x47,63x22,23xM10(=)
E3 9/16-18UNF MG 25/20x52,37x26,19xM10(=)
E4 3/4-16UNF MH 31/25x58,72x30,18xM10(=)
E5 7/8-14UNF
E6 1-1/16-12UN
E8 1-5/16-12UN

J Ports Pos & Spec Body

NN Std from catalogue Inlet port Right position looking gear drive from
PR
YY Port Bx-Bx with flange SAE-A;off-set to rear cover front flange
EU Dist. from front flange=58,5 - Special TD Nr.4 milling D.27 tigh.16 flange side - Special
F9 Dist. from front flange=69 - Special TE Nr.4 milling D.27 tigh.20 flange side - Special
Inlet port Left position looking gear drive from ZZ Port Bx-Bx in the center of the body - Option
PL
front flange
Turolla - L1016082 • September 2013 • Rev C
 GEAR MOTORS I TECHNICAL INFORMATION 35

A B C D E F G H I J K L M N 0
/

K Seals

N Standard NBR seals

B VITON seals (only for unidirectional motors)
D VITON shaft seal with dust lip (type BABSL)
F VITON seals except for shaft seal - Special
X NBR seals+Dust Cover
Y VITON seals + Dust Cover
Z VITON shaft seal + Dust Cover

L Screws

N Std burnished screws

A Zinc plated screws
C Galvanized nuts - Special

M Set valves
NNN No valve
V** not defined-pressure no setting :oil ISO VG68-45°

N Type of mark

N Standard Turolla Marking

A Standard Turolla Marking+Customer Code-Special
Z Without Marking

O Mark position

N Std Marking position (on top)

A Special Marking position on the bottom

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
36 GEAR MOTORS I TECHNICAL INFORMATION

Motor performance graphs

The graphs on the next few pages provide typical output flow and input power for Group 2 motors at various working
pressures. Data were taken using ISO VG46 petroleum /mineral based fluid at 50 °C [122 °F] (viscosity = 28 mm2/s [132 SUS]).

SNM2NN/6,0 motor performance graph SNM2NN/8,0 motor performance graph

SNM2NN/011 motor performance graph SNM2NN/014 motor performance graph

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 37

SNM2NN/017 motor performance graph SNM2NN/019 motor performance graph

SNM2NN/022 motor performance graph SNM2NN/025 motor performance graph

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
38 GEAR MOTORS I TECHNICAL INFORMATION

Flange, shaft and port configurations

Flange, shaft and port configurations for SNM2NN and SNU2NN motors
Code Flange Shaft Port

European 01, 4-bolts European

01BA 1:8 tapered
pilot Ø 36.5 mm [1.44 in] in + pattern

European 02, 4-bolts German standard

02AA 1:5 tapered
pilot Ø 80 mm [3.15 in] in X pattern

04AA/ German PTO 2-bolts German standard

1:5 tapered
05AA pilot Ø 50 mm [1.97 in] in X pattern

European 01, 4-bolts Ø 15 mm [0.59 in] European

01FA
pilot Ø 36.5 mm [1.44 in] parallel in + pattern

SAE A Ø 15.7 mm [0.625 in] Threaded SAE

06GA
pilot Ø 82.55 mm [3.25 in] parallel O-ring boss port

9-teeth splined
European 01, 4-bolts European
01DA m = 1.60, α = 30o
pilot Ø 36.5 mm [1.44 in] in + pattern
DIN 5482-B17x14

9-teeth splined
European 02, 4-bolts German standard
02DB m = 1.60, α = 30o
pilot Ø 80 mm [3.15 in] in X pattern
DIN 5482-B17x14

9-teeth splined
04DB/ German PTO 2-bolts German standard
m = 1.60, α = 30o
05DB pilot Ø 50 mm [1.97 in] in X pattern
DIN 5482-B17x14

SAE A SAE Threaded SAE

06SA
pilot Ø 82.55 mm [3.25 in] 9-teeth splined O-ring boss port

Turolla tang Turolla German standard

03CA
pilot Ø 52 mm [2.066 in] standard tang in X pattern

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 39

Shaft options
Group 2 motors are available with a variety of splined, parallel, and tapered shaft ends. Not all shaft styles are available
with all flange styles.
Valid combinations and nominal torque ratings are shown in the table below. Torque ratings assume no external radial
loading. Applied torque must not exceed these limits regardless of pressure parameters stated earlier. Maximum
torque ratings are based on shaft torsional fatigue strength.
Shaft availability and nominal torque capability
A B C D E F G H I J K L M N 0
/

Shaft Mounting flange code with maximum torque in N•m [lb•in]

Code Description 01 02 B2 Q2 03 04 05 L5 06
AA Taper 1:5-M12x1,25-Key 3 140 [1239] 140 [1239] 140 [1239] 140 [1239]
AC Taper 1:5-M14x1,5-Key 4 140 [1239]
Taper 1:5-M12X1,25-Key 3-Drive
AD 140 [1239] 140 [1239] 140 [1239]
(Version 6 only)
Taper 1:8-M12x1,25-Key 4/6
B1 150 [1328]
lowered
BA Taper 1:8-M12x1,25-Key 4 150 [1328] 150 [1328] 150 [1328] 150 [1328]
BB Taper 1:8-M12x1,25-Key 4/3,2 150 [1328] 150 [1328]
Taper 1:8-M12x1,25-Key 4/3
BJ 150 [1328]
black steel
CA Tang 8x17,8xL6,5 FR03 70 [620]
CF Tang 8x Ø17,46xL9,6-Special
DA Spline DIN 5482 B17x14-L10 90 [797]
DB Spline DIN 5482 B17x14-L14 130 [1151] 130 [1151] 130 [1151] 130 [1151]
FA Parallel Ø15-L30+Key 4x25 90 [797]
Parallel SAE Ø15,875-L23,8-Key
GA 80 [708]
4x18
Parallel SAE Ø15,875-L50,8-Key
GB 80 [708]
4x40
SA Spline SAE J498-9T-16/32 75 [646]
Spline SAE J498-11T-16/32
SB 150 [1328]
(Version 2 only)
Spline SAE J498-9T-16/32+M6
SE 75 [646]
thd hole
Spline SAE J498-9T-16/32-
SF 90 [797]
reinforced fillet
Spline SAE J498-11T-16/32
SG 150 [1328]
(Version 2 only)
Spline SAE J498-11T-16/32
SI 150 [1328]
(Version 2 only)

Recommended mating splines for Group 2 splined output shafts should be in accordance with SAE J498 or DIN 5482. Turolla
external SAE splines are flat root side fit with circular tooth thickness reduced by 0.127 mm [0.005 in] in respect to class 1 fit.
The external DIN splines have an offset increased by 0.1 mm [0.004 in.] These dimensions are modified in order to assure a
clearance fit with the mating spline.
Other shaft options may exist. Contact your Turolla representative for availability.

Caution

Shaft torque capability may limit allowable pressure. Torque ratings assume no external radial loading. Applied torque must
not exceed these limits, regardless of stated pressure parameters. Maximum torque ratings are based on shaft torsional
fatigue strength.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
40 GEAR MOTORS I TECHNICAL INFORMATION

Port dimensions
Available ports for Group 2 motors
B C D E F

45o

g x d e f

h y
i (4 holes min. full thd. z (4 holes min. full thd.
20 mm [0.787 in] deep) 20 mm [0.787 in] deep)

Bidirectional motor ports dimensions

SNM2NN bidirectional motors and SNM2GN, SNM2JN, SNM2IN motors made unidirectional only by the valve
Port type B C D E F
Port dimensions g h i x y z d e f
6,0 Inlet/Outlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M22x1.5 7/8 –14UNF–2B ½ Gas (BSPP)
8,0 Inlet/Outlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M22x1.5 7/8 –14UNF–2B ½ Gas (BSPP)
011 Inlet/Outlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M22x1.5 7/8 –14UNF–2B ½ Gas (BSPP)
Frame size

014 Inlet/Outlet 15 [0.59] 35 [1.38] M6 20 [0.79] 40 [1.58] M8 M22x1.5 7/8 –14UNF–2B ½ Gas (BSPP)
017 Inlet/Outlet 15 [0.59] 35 [1.38] M6 20 [0.79] 40 [1.58] M8 M22x1.5 7/8 –14UNF–2B ½ Gas (BSPP)
019 Inlet/Outlet 20 [0.79] 40 [1.58] M6 20 [0.79] 40 [1.58] M8 M26x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
022 Inlet/Outlet 20 [0.79] 40 [1.58] M6 20 [0.79] 40 [1.58] M8 M26x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
025 Inlet/Outlet 20 [0.79] 40 [1.58] M6 23.5 [0.92] 40 [1.58] M8 M26x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
Drain ¼ Gas (BSPP) 9/16 –18UNF–2B ¼ Gas (BSPP)

Unidirectional motor ports dimensions

SNU2NN and SKU2NN ports dimensions

Port type B C D E F
Port dimensions g h i x y z d e f
Inlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M18x1.5 1-1/16 –12UNF–2B ½ Gas (BSPP)
8,0
Outlet 20 [0.79] 40 [1.58] M6 13.5 [0.53] 30 [1.18] M6 M16x1.5 ⁷⁄₈–14UNF–2B ½ Gas (BSPP)
Inlet 15 [0.591] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M18x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
011
Outlet 20 [0.79] 40 [1.58] M6 13.5 [0.53] 30 [1.18] M6 M16x1.5 ⁷⁄₈–14UNF–2B ½ Gas (BSPP)
Inlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M18x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
014
Outlet 20 [0.79] 40 [1.58] M6 20 [0.79] 40 [1.58] M8 M16x1.5 ⁷⁄₈–14UNF–2B ½ Gas (BSPP)
Frame size

Inlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M18x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
017
Outlet 20 [0.79] 40 [1.58] M6 20 [0.79] 40 [1.58] M8 M18x1.5 ⁷⁄₈–14UNF–2B ½ Gas (BSPP)
Inlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M18x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
019
Outlet 20 [0.79] 40 [1.58] M6 20 [0.79] 40 [1.58] M8 M18x1.5 ⁷⁄₈–14UNF–2B ½ Gas (BSPP)
Inlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M18x1.5 1-1/16 –12UNF–2B ¾ Gas (BSPP)
022
Outlet 20 [0.79] 40 [1.58] M6 20 [0.79] 40 [1.58] M8 M18x1.5 ⁷⁄₈–14UNF–2B ½ Gas (BSPP)
Inlet 15 [0.59] 35 [1.38] M6 13.5 [0.53] 30 [1.18] M6 M18x1.5 1-1/16 –12UNF–2B 1 Gas (BSPP)
025
Outlet 20 [0.79] 40 [1.58] M6 20 [0.79] 40 [1.58] M8 M18x1.5 ⁷⁄₈–14UNF–2B ¾ Gas (BSPP)

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 41

Integral relief valve – SNM2IN Valve schematic diagram

Turolla offers an optional integral relief
valve integrated in the Group 2 motors rear
cover. It is drained internally and directs all
the flow from the motor inlet to the outlet
when the inlet pressure reaches the valve
setting.

The tables below show applicable variant

codes for ordering motors with integral relief
valve. Refer to Model Code, page 35 for more
information.

Integral relief valve rear cover cross section Pressure vs flow

[psi] bar With mineral oil at 26 mm2/s
400
[5000]
300
[4000]

[3000] 200

[2000]
100
[1000]
Inlet
Drain MINIMUM VALVE SETTING
0 0
10 20 30 40
P101 016 l/min

0 [2] [4] [6] [8] [10]

[US gal/min]

Variant codes for ordering integral relief valve

A B C D E F G H I J K L M N 0
/ V

M Variant code (left part) M Variant code (right part)

Motor speed for RV setting Pressure setting bar Pressure setting bar
Code Code Code
min-1 (rpm) [psi] [psi]
A not defined A no setting O 90 [1305]
C 500 B no valve P 100 [1450]
E 1000 C 18 [261] Q 110 [1595]
F 1250 D 25 [363] R 120 [1740]
G 1500 E 30 [435] S 130 [1885]
K 2000 F 35 [508] T 140 [2030]
I 2250 G 40 [580] U 160 [2321]
L 2500 J 150 [2175] V 170 [2466]
M 2800 K 50 [725] W 180 [2611]
N 3000 L 60 [870] X 210 [3046]
O 3250 M 70 [1015] Z 250 [3626]
N 80 [1160]

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
42 GEAR MOTORS I TECHNICAL INFORMATION

Anti-cavitation check valve – SNM2GN

Turolla offers an optional integral anti-cavitation check valve integrated in Group 2 motors
bearing blocks. Available for all the displacements, the valve directs internally the flow from the
motor outlet to the inlet, when the outlet pressure gets higher then the inlet one.

Valve schematic diagram Anticavitation check valve cross section

Integral relief valve and Anti-cavitation check valve – SNM2JN

Turolla offers the Group 2 motors with an optional integral relief valve integrated in the rear
cover and anti-cavitation check valve integrated in the bearing block. The integral relief
valve is drained internally and directs all the flow from the motor inlet to the outlet when the inlet
pressure reaches the valve setting. The anti-cavitation check valve directs internally the flow from
the motor outlet to the inlet, when the outlet pressure gets higher then the inlet one.

Valve schematic diagram

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 43

Outrigger bearing assembly – SNM2NN

An outrigger bearing is available for applications with high radial or thrust loads on the shaft.
This option is used primarily for applications with high shaft loads. The design utilizes roller bear-
ings in the front mounting flange. These bearings absorb the radial and thrust loads on the shaft
so that the life of the motor is not affected. The use of roller bearings allows life to be described in
B10 hours.

Available configurations

A B C D E F G H I J K L M N 0
/

Flange/Shaft Code* Mounting Flange Shaft

9A European 4-bolt Taper 1:8
9F German PTO Taper 1:5
94 German 4-bolt Taper 1:5
9H SAE A Taper 1:8
9J SAE A Parallel

* Codes represent assembly (complete motor with outrigger bearing).

The table above shows applicable variant codes for ordering motors with outrigger
bearing. Refer to Model Code, page 31 for more information.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
44 GEAR MOTORS I TECHNICAL INFORMATION

Outrigger bearing assembly – SNM2NN

The graphs below show allowable shaft loads for 1000 hour life at 1500 min-1 (rpm) versus distance
from flange face to center of radial load.

Radial load vs distance from flange

2400 2400

SNM2NN / 9ADB SNM2NN / 9FDB

2000 2000

1600 1600
Load N
Load N

1200 1200
Radial Load Radial Load

800 800

Axial Load
400 400
Axial Load
200 200

0 0
10 20 30 40 50 60 10 20 30 40 50 60
Distance a (mm) Distance a (mm)

3500 2400

SNM2NN / 94DB SNM2NN / 9HDB

3000 2000

2500 1600
Load N
Load N

2000 1200
Radial Load Radial Load

1500 800

1000 400 Axial Load

Axial Load
500 200

0 0
10 20 30 40 50 60 10 20 30 40 50 60
Distance a (mm) Distance a (mm)

2400

SNM2NN / 9JDB
2000 a Distance from flange face
to center of radial load
1600
Load N

1200
Radial Load
800
Axial Load

400

200

0
10 20 30 40 50 60
Distance a (mm)

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 45

Outrigger bearing 9A
mm
[in]
+0.15 +0.006
43 - 0.15 [1.693 - 0.006 ]

0
3.2 - 0.025
0
[0.126 - 0.0010]

- 0.014 ]
+0.006
+0.15
- 0.35
Taper 1:8

9.5
[0.374
A ±0.50 [0.020]

D max

Outrigger bearing 94

+0.15 +0.006
46.5 - 0.15 [1.831 - 0.006 ]

0 0
3 -0.025
025 [0.118-0.001]
0.0

Taper 1:5 +0.012

9 +0.30
-0.10 [0.354 -0.004 ]

B ±0.50 [0.020]

E max

Outrigger bearing 9J
+0.15 +0.15
35 - 0.15 43.5 - 0.15
+0.006 +0.006
[1.378 - 0.006 ] [1.713 - 0.006 ]
6.5 - 8.5
[0.256 - 0.335]

0
4.755 - 0.030
0
[0.187 - 0.0012 ]
20.900 - 21.125
[0.823 - 0.832]

0
19.05 - 0.033
0
[0.75 - 0.0013 ]

C ±0.50 [0.020]
D max
P005 276E

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
46 GEAR MOTORS I TECHNICAL INFORMATION

Outrigger bearing 9F
mm
+0.10
[in]
34 - 0.10 44.22 - 45.88
+0.004
[1.339 - 0.004 ] [1.741 - 1.806]
0
8 - 0.20
0
[0.157- 0.0012 ]

0
4 - 0.030
[0.157 - 00.0012 ]

Taper 1:5 +0.30 +0.012

10.7 -0.10 [0.421 -0.004 ]

A ±0.50 [0.020]

D max

Outrigger bearing 9H
+0.05
35 - 0.05 40.48 - 39.32
+0.002
[1.378 - 0.002 ] [1.594 - 1.548]
6 [0.236]

0 0
4 -0.030 [0.158-0.001]

Taper 1:8 +0.006

9.5 +0.15
-0.25 [0.374 -0.010 ]

B ±0.50 [0.020]

D max

Dimensions
Frame size 6,0* 8,0 011 014 017 019 022 025
45 45 49 52 52 56 59 59
A
[1.772] [1.772] [1.929] [2.047] [2.047] [2.205] [2.323] [2.323]
38.6 40.6 45 45 45 45 52.5 62
B
[1.520] [1.598] [1.772] [1.772] [1.772] [1.772] [2.067] [2.441]
45 47 49 52 54 56 59 61
Dimension C
[1.772] [1.850] [1.929] [2.047] [2.126] [2.205] [2.323] [2.402]
93.5 97.5 101.5 107.5 111.5 115.5 121.5 125.5
D
[3.681] [3.839] [3.996] [4.232] [4.390] [4.574] [4.783] [4.941]
85 89 93 99 103 107 113 117
E
[3.346] [3.504] [3.661] [3.897] [4.055] [4.212] [4.448] [4.606]

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 47

Dimensions

SNM2NN, SNU2NN – 01DA, 01FA and 01BA

Standard porting drawing for 01DA, 01FA and 01BA
mm
01DA 01FA 01BA [in]

B max 40.5
[1.596]
A ±0.50 [0.020] 17
19.5 36.5 [0.670]
[1.438]

(41.9 [1.651])
[0.768] 6.3 21.7
Ø15 -0.018[0.591-0.001]

10 30 90 ±0.25[3.546 ±0.010] [0.248] [0.854]

0

[0.394] [1.182] body width 5

-0.002 ]
18

-0.025
Ø 36.5 -0.050
[1.438 -0.001
Ø 17.46 [0.687]
6.5 6.5 [0.709] [0.02]
[0.256] [0.256]
0

B A
[1.277]
32.4

[1.24 ±0.020]

115.2 [4.539] max

31.4 ±0.50
(96.2 [3.790])

M12x1.25-6g
(73.3 [2.888])
[2.514]

A
[0.650 -0.004 ]

63.8

15.7 ±0.50 [0.619 ±0.020]

C/c
0

X
Ø 16.5 -0.110
0

M6 thread 16 [.630] deep 1 :8

9
(min full thd 12 [0.472] deep) E/e
Spline: Ø 0.75 [0.030] X
[3.55]
B17x14 DIN 5482 D/d ±0.20 [0.008]
Profile offset +0.6 [0.024] 71.5
B-B 1/4 Gas Drain port Nut and washer supplied with pump
0
4 -0.03 [2.817]
Recommended tightening torque: 45-55 Nm
0
[0.158-0.001] 90 max
[3.546]
A-A
0
4 -0.03 9.5 +0.15
-0.25
16.5 +0.1
-0.2 0
[0.158-0.001] +0.006
+0.004 [0.374 -0.01 ]
[0.650 -0.008 ]

For unidirectional motors no case drain hole into the rear cover.

Bidirectional motors dimensions – 01DA, 01FA and 01BA

Frame size
8,0 011 014 017 6,0*
019 022 025
45 49 52 56 59
A
[1.771] [1.929] [2.047] [2.204] [2.322]
Dimension
93.5 97.5 101.5 107.5 111.5 121.5 125.5
B
[3.681] [3.838] [3.996] [4.232] [4.389] [4.783] [4.940]
13.5 20 23.5
C/c
[0.531] [0.787] [0.925]
Inlet/Outlet
D/d 30 [1.181] 40 [1.58]
E/e M6 M8
* Before chosing this frame size, please apply to Turolla technical department.

For unidirectional SNU2NN dimensions, see SNU2NN ports, page 40.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
01DA SNM2NN/8,0BN01DAM1C3C3NNNN/NNNNN 90 N•m [797 lb•in]
01FA SNM2NN/022BN01FAM1C7C7NNNN/NNNNN 90 N•m [797 lb•in]
01BA SNM2NN/017BN01BAM1C7C7NNNN/NNNNN 150 N•m [1328 lb•in]
For further details on ordering, see Model Code, pages 30-35.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
48 GEAR MOTORS I TECHNICAL INFORMATION

SNM2NN, SNU2NN – 02DB and 02AA

Standard porting drawing for 02DB and 02AA
mm
[in]
02DB 02AA
B max 38 [1.496]

Ø 80 --0.090 [3.150 -0.003 ]

-0.002
A ±0.50 16.5 [0.650]

(44.5 [1.72])
23.5 [0.952] 5.7 [0.224] 19.3 [0.760]
90 ±0.25 [ 3.543 ±0.010 ]

0.060
body width
13.5 [0.531] 31.4 ±0.5 [1.24 ±0.0197 ] C/c 12.5 [0.492] 7.2 [0.283]

[0.687]
17.46
A
[1.358]
34.5

120 [4.724] max

(100 [3.937])

(75.5 [2.972])

M12x1.25-6g
A
Ø 16.5 -0.110 [0.650 -0.004 ]

[2.579]

15.7±0.50 [0.618 ±0.020]

65.5
0

45°

X
0

9 [0.354] (min full thd 12 [0.472] deep) E/e 1 :5

Ø 0.75 [0.030] X

Spline: B17x14 DIN 5482 72 1/4 Gas D/d ±0.20 [0.008]

Profile offset +0.6 [.024] [2.835] Drain port
Nut and washer supplied with pump
92 [3.622] max Recommended tightening torque: 45-55 Nm
A-A
0 0 +0.30 +0.012
3 -0.025 [0.118 -0.001 ] 9 -0.10 [0.354 -0.004 ]

For unidirectional motors no case drain hole into the rear cover.

Bidirectional motors dimensions – 02DB and 02AA

Frame size 6,0* 8,0 011 014 017 019 022 025
41.1 43.1 47.5 47.5 47.5 47.5 55 64.5
A
[1.618] [1.697] [1.870] [1.870] [1.870] [1.870] [2.165] [2.539]
Dimension
96 100 104 110 114 118 124 128
B
[3.780] [3.937] [4.094] [4.331] [4.488] [4.646] [4.882] [5.039]
C/c 15 [0.591] 20 [0.79]
Inlet/Outlet D/d 35 [1.38] 40 [1.58]
E/e M6
* Before chosing this frame size, please apply to Turolla technical department.

For unidirectional SNU2NN dimensions, see SNU2NN ports, page 40.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
02DB SNM2NN/025BN02DBM1B7B7NNNN/NNNNN 90 N•m [797 lb•in]
02AA SNM2NN/8,0BN02AAM1B5B5NNNN/NNNNN 140 N•m [1239 lb•in]
For further details on ordering, see Model Code, pages 30-35.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 49

SNM2NN, SNU2NN – 03CA

Standard porting drawing for 03CA
mm
[in]
03CA

8.5 [0.335] B ±0.50 [±0.02]

90 ±0.25 [3.576 ±0.010] A ±0.50 [±0.02] 7.2 [0.286]

body width
+0.20 +0.008 12 [0.477]
+0.20
2 [0.079] 3.2 0 [0.127 0 ] 6.5 0
+0.008
[0.258 0 ] 2.7 +0.70 +0.028 ]
0 [0.107 0

Ø 34 [1.351]

Ø 30 [1.192]
X
[0.568]
31.4 ±0.50 [1.24 ±0.0197]

C/c
14.3
103 [4.092] max

(60 [2.384])
[1.816]

-0.083 [0.318 -0.003 ]

+0.001
45.7

19 [.755]
15.7 ±0.50 [0.624 ±0.020]
8 [0.315]
Ø 52 -0.060 [2.066 -0.002 ]

[1.899-0.008 ]
-0.001

45°
0

8 +0.025
-0.030

Ø 47.8 -0.20

+0.27
11.5 0
0

1/4 gas drain port Ø 0.75 [0.030] X Coupling supplied with pump
30 30 [0.457 +0.011
0 ]
[1.192] [1.192]
E/e (min full thd 12 [0.477] deep)
O-ring 45.69 x 2.62 (60 [2.384])
D/d ±0.20 [±0.008]

For unidirectional motors no case drain hole into the rear cover.

Bidirectional motors dimensions – 03CA

Frame size 6,0* 8,0 011 014 017 019 022 025
38.6 40.6 52.5 62
A 45 [1.772]
[1.520] [1.598] [2.067] [2.441]
Dimension
85 89 93 99 103 107 113 117
B
[3.364] [3.503] [3.661] [3.897] [4.055] [4.212] [4.448] [4.606]
C/c 15 [0.591] 20 [0.79]
Inlet/Outlet D/d 35 [1.38] 40 [1.58]
E/e M6
* Before chosing this frame size, please apply to Turolla technical department.

For unidirectional SNU2NN dimensions, see SNU2NN ports, page 40.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
03CA SNM2NN/014BN03CAM3B5B5NNNN/NNNNN 70 N•m [620 lb•in]
For further details on ordering, see Model Code, pages 30-35.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
50 GEAR MOTORS I TECHNICAL INFORMATION

SNM2NN, SNU2NN–04DB/05DB and 04AA/05AA

Standard porting drawing for 04DB/05DB and 04AA/05AA 04AA / 05AA mm
[in]
04DB / 05DB 04 Body 8.5 [0.335] B ±0.50 [±0.02] 40.5 [1.594]

-0.050 [1.969 -0.002 ]

-0.001
90 ±0.25 [0.010] A ±0.50 [±0.02] 19 [0.748]
26 [1.024]
body width
8.2 [0.323] 19.3 [0.760]
13.5 [0.531] +0.27
11.5 0

Ø 50 -0.025
Ø0.75 [0.030] X C/c 7.2 [0.283]
[0.453 +0.011 ]

[0.563]
0

14.3

[0.687]
17.46
A
103 [4.055] max

31.4 ±0.50 [1.24 ±0.02]

(60 [2.362])
[1.799]
45.7

M12x1.25-6g
[0.650 -0.004 ]

15.7 ±0.50 [0.618 ±0.02]

A
0

45°
X
Ø 16.5 -0.110
0

1/4 Gas Drain port (min full thd 12 [0.472] deep) E/e 1 :5
30 30
[1.181] [1.181]
Spline: D/d ±0.20 [±0.008]
B17x14 DIN 5482
(60 [2.362])
Profile offset +0.6 [0.024] Nut and washer supplied with pump
Recommended tightening torque: 45-55 Nm

-0.10 [0.354 -0.004 ]

+0.012
05 Body
A-A
0 0
3 -0.025 [0.118-0.001]
9 +0.30

For unidirectional motors no case drain hole into the rear cover.

Bidirectional motors dimensions – 04/05DB and 04/05AA

Frame size 6,0* 8,0 011 014 017 019 022 025
38.6 40.6 52.5 62
A 45 [1.772]
[1.520] [1.598] [2.067] [2.441]
Dimension
85 89 93 99 103 107 113 117
B
[3.364] [3.503] [3.661] [3.897] [4.055] [4.212] [4.448] [4.606]
C/c 15 [0.591] 20 [0.79]
Inlet/Outlet D/d 35 [1.38] 40 [1.58]
E/e M6
* Before chosing this frame size, please apply to Turolla technical department.

For unidirectional SNU2NN dimensions, see SNU2NN ports, page 40.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
04DB SNM2NN/8,0BN04DBAM1B5B5NNNN/NNNNN
130 N•m [1151 lb•in]
05DB SNM2NN/017BN05DBM1B5B5NNNN/NNNNN
04AA SNM2NN/8,0BN04AAM1B5B5NNNN/NNNNN
140 N•m [1239 lb•in]
05AA SNM2NN/017BN05AAM1B5B5NNNN/NNNNN
For further details on ordering, see Model Code, pages 30-35.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 51

SNM2NN, SNU2NN, SKU2NN – 06SA, 06GA

mm
Standard porting drawing for 06SA and 06GA [in]

06SA 06GA
31.7 [1.248] 132 [5.197] max B max 31.7

Ø 82.55 -0.5 [3.250 -0.02 ]

[1.248]
106.38 [4.188] A ±0.5 [0.02]

0
23.8 7.9 [0.311]
[0.937]
11 - 11.6 [0.433 - 0.457]

20 [0.787] 7.9 [0.311] 23.8 [0.937]

R 48 [1.889] max

0
12 [0.472] 6 [0.236]
31.4 ±0.5 [1.24 ±0.02]

A
115.5 [4.547] max

M6-6H- THD 16 [0.630] deep

]

A
[Dia 0.609-0.005

15.7 ±0.50 [0.618 ±0.02 ]

Ø 15.456 -0.127

Ø 0.75 [0.03] X

Ø 15.875 -0.025 [0.625 -0.01

0

0
0

Straight thread C/c 0

90±0.25 O-ring boss
9/16-18UNF-2B [3.543±0.01]
Straight thread body width
O-ring boss A-A
0 0
17.475 -17.729
3.995 -0.025 [0.157 -0.010 ] [0.688 - 0.698]
Splined SAE J498-9T-16/32DP
flat root side fit
(circular tooth thickness 0.127 [0.005]
less than standard class 1 fit)

For unidirectional motors no case drain hole into the rear cover.

Bidirectional motors dimensions – 06SA and 06GA

Frame size 6,0* 8,0 011 014 017 019 022 025
45 47 49 52 54 56 59 61
A
[1.772] [1.850] [1.920] [2.047] [2.205] [2.205] [2.323] [2.402]
Dimension
93.5 97.5 101.5 107.5 111.5 115.5 121.5 125.5
B
[3.681] [3.839] [3.996] [4.232] [4.390] [4.547] [4.783] [4.941]
1 1/16–12UNF–2B,
Inlet/Outlet C/c / –14UNF–2B, 16.7 [0.658] deep
7 8
18.0 [0.709] deep
* Before chosing this frame size, please apply to Turolla technical department.

For unidirectional SNU2NN dimensions, see SNU2NN ports, page 40.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
06SA SNM2NN/8,0BN06SAM1E5E5NNNN/NNNNN 75 N•m [664 lb•in]
06GA SNM2NN/017BN06GAM6E5E5NNNN/NNNNN 80 N•m [708 lb•in]
For further details on ordering, see Model Code, pages 30-35.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
52 GEAR MOTORS I TECHNICAL INFORMATION

GROUP 3 GEAR MOTORS

Motor design SNM3NN 01BA

SNM3NN
SNM3NN is the Group 3 bidirectional motor
available in the whole displace-ments range
from 22 up to 90 cm3/rev [1.35 up to 5.38 in3/
rev].

Configurations include European and SAE

flanges and shafts (01BA, 01FA, 01DA, 02AA,
02FA, 02DB, 03BB, 03FB, 06AA, 06DD, 07BC,
07GA, 07SA).

SNU3NN SNU3NN 01BA (cut away)

SNU3NN is the Group 3 unidirectional motor
available in the whole displace-ments range
from 22 up to 90 cm3/rev [1.35 up to 5.38 in3/
rev].

The SNU3NN motor construction is derived

from the correspondent pump SNP3.

Configurations include European and SAE

flanges and shafts (01BA, 01FA, 01DA, 02AA,
02FA, 02DB, 03BB, 03FB, 03DB, 06AA, 06SA,
07BC, 07GA, 07SA).

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 53

Technical data
This table details the technical data for Group 3 gear motors based on the model and displace-
ment configuration.

Technical data for Group 3 gear motors

Frame size
022 026 033 038 044 048 055 063 075 090
cm3/rev 22.1 26.2 33.1 37.9 44.1 48.3 55.2 63.4 74.4 88.2
Displacement
[in3/rev] [1.35] [1.60] [2.02] [2.32] [2.69] [2.93] [3.36] [3.87] [4.54] [5.38]
SNU3NN (unidirectional)
270 270 270 270 270 250 230 210 190 170
Peak pressure
[3915] [3915] [3915] [3915] [3915] [3625] [3336] [3045] [2755] [2465]
bar [psi]
250 250 250 250 250 230 210 190 170 150
Rated pressure
[3625] [3625] [3625] [3625] [3625] [3336] [3045] [2755] [2465] [2175]
Minimum speed 800 800 800 800 800 800 800 600 600 600
min-1 (rpm)
Maximum speed 2500 2500 2500 2500 2300 2300 2300 2300 2100 2100
SNM3NN (bidirectional) motor in parallel
270 270 270 270 270 250 230 210 190 170
Peak pressure
[3915] [3915] [3915] [3915] [3915] [3625] [3336] [3045] [2755] [2465]
bar [psi]
250 250 250 250 250 230 210 190 170 150
Rated pressure
[3625] [3625] [3625] [3625] [3625] [3336] [3045] [2755] [2465] [2175]
Minimum speed 800 800 800 800 800 800 800 800 800 800
min-1 (rpm)
Maximum speed 2500 2500 2500 2500 2300 2300 2300 2300 2100 2100
SNM3NN (bidirectional) motor in series
250 250 250 250 250 230 210 190 170 150
Peak pressure
[3625] [3625] [3625] [3625] [3625] [3336] [3045] [2755] [2465] [2175]
bar [psi]
250 250 250 250 250 230 210 190 170 150
Rated pressure
[3625] [3625] [3625] [3625] [3625] [3336] [3045] [2755] [2465] [2175]
Minimum speed 800 800 800 800 800 800 800 800 800 800
min-1 (rpm)
Maximum speed 2500 2500 2500 2500 2300 2300 2200 2100 2100 2100
All (SNU3NN, SNM3NN)
6.8 6.8 7.2 7.3 7.5 7.6 7.8 8.1 8.5 8.9
Weight kg [lb]
[15.0] [15.0] [15.8] [16.1] [16.5] [16.8] [17.3] [17.9] [18.7] [19.6]
Moment of inertia of x 10-6 kg•m2 198 216 246 267.2 294.2 312.2 342.3 378.3 426.4 486.5
rotating components [x 10-6 lb•ft2] [4698] [5126] [5837] [6341] [6981] [7408] [8123] [8977] [10 118] [11 545]
1 kg•m2 = 23.68 lb•ft2

Caution

The rated and peak pressure mentioned are for motors with flanged ports only. When threaded ports are required a de-
rated performance has to be considered. To verify the compliance of an high pressure application with a threaded ports
pump apply to a Turolla representative.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
54 GEAR MOTORS I TECHNICAL INFORMATION

Product Code
Model Code
A B C D E F G H I J K L M N 0
/

A Family

SEU3NN Low Cost Gr3 Unidirecional Motor

SNU3NN Gr3 Unidirectional Motor
SNU3GN Gr3 Unidirectional Motor+Anticav.Check Valve
SNM3NN Gr3 Bidirectional Motor - Axial drain on cover
SNM3NL Gr3 Bidirectional Motor-Vert.drain on rear cover
SNM3GN Gr3 Bidirectional Motor-Anticav.Check Valve - Axial drain on cover
SNM3GL Gr3 Bidirectional Motor-Anticav.Check Valve - Vert.drain on rear cover
SNM3CN Gr3 Bidirectional Motor-Anticav.Check valve on Cover
SNM3DN Gr3 Bidirectional Motor-Internal drain valve

B Displacement

022 22,1 cc
026 26,2 cc
033 33,1 cc
038 37,9 cc
044 44,1 cc
048 48,3 cc
055 55,2 cc
063 63,4 cc
075 74,4 cc
090 88,2 cc

C Rotation

B Bidirectional
L Left rotation
R Right rotation

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 55

A B C D E F G H I J K L M N 0
/

D Project version (value representing

a change to the initial project)

N Std Version of Project

E Mounting flange F Drive gear

AA Taper 1:5-M16x1,5-Key 5
Description (Type of flange • Type of drive gear
Code BA Taper 1:8-M14x1,5-Key 4
• Preferred ports for configuration)
BB Taper 1:8-M16x1,5-Key 4,79
01 Pilot Ø50,8+4 holes (98,4x128,1) BC Taper 1:8-5/8-18UNF-2A-Key 6,375
02 Pilot Ø50,8+4 holes (98,4x137) BD Taper 1:8-M14x1,5-Key 4 + thd hole M8 - Special
03 Pilot Ø60,3+4 holes (114,3x149,5) Taper 1:8-5/8-18UNF-2A-Key 6,375 with NUT &
BP
06 Pilot Ø105+4 holes (102,0x145,0)
WASHER (for flange 07)
07 SAE B-pilot Ø101,6 -2 holes CA Tang 8xØ22,2 - Special
08 SAE C-pilot Ø127 -4 holes Tang 12xØ24-shaft flange protrusion sb17.5-dr72.5-
CB
09 SAE A-pilot Ø82,55 -2 holes Special
Outrigger bearing typo 01 -Taper 1:8 M14x1,5 key DA DIN 5482 B22x19 L=24 (for flange typo 01)
91
4x7,5 DD DIN 5482 B28x25 L28 (for flange typo 06)
Outrigger bearing type 07 -taper shaft FA Parallel Ø20-Key 5x5 L30 (for flange typo 01-02)
9Y
1:8-5/8-18UNF-Key6,375 with Dust Cover FB Parallel Ø22-Key 5x5 L40 (for flange typo 03)
Pilot Ø50,8+4 holes special shaft seal slot - Special GA Parallel Ø22,225 x L25,4-Key 6,375x6,375 L25,4
B1
01 Parallel Ø22,225xL25,4-Key 6,375x6,375x25,4+thd
GB
Pilot Ø105+4 holes + shaft seal D40 per shaft spline hole:1/4-20UNC-2B
D6
- Special 06 Parallel Ø22,225xL25,4-Key 6,375x6,375x25,4+thd
GC
D7 Pilot Ø101,6+2 holes + double shaft seal - Special 07 hole:5/16-18UNC-2B - Special
P1 Pilot Ø50,8+4 holes Ø12-12,5 - Special 01 SA SAE J498-13T-16/32-SAE B
P7 Pilot Ø101,6+2 fixed holes slot - Special 07 SB SAE J498-13T-16/32-SAE A (for flange typo 09)
SAE J498-14T-12/24-SAE C-4 bolt (for flange typo
RA
08)
SH SAE J498-15T-16/32-(for flange typo 07)

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
56 GEAR MOTORS I TECHNICAL INFORMATION

A B C D E F G H I J K L M N 0
/

G Rear cover

P1 Std cover for unidirectional motors

M1 Std cover motor axial drain on cover M14x1,5
M2 Std cover motor axial drain on cover M12x1,5 ISO6149
M6 Std cover motor axial drain on cover 9/16-18UNF-2B
MF Std cover motor axial drain on cover drain 3/8 Gas
L1 Cover motor with radial drain on cover - Vertical M14x1,5
L2 Cover motor with radial drain on cover - Horizontal M14x1,5
L6 Cover motor with radial drain on cover - Vertical 9/16-18UNF-2B
LT Cover motor with radial drain on cover - Vertical 9/16-18UNF-2B drain up
C1 Cover motor with front metric ports : M22x1,5 - for SNM3CN series
D1 Cover motor without drain (internal drained) - for SNM3DN series

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 57

A B C D E F G H I J K L M N 0
/

H Inlet size I Outlet size

18,5x22,23x47,63x3/8-
A2 M5 25x52,37x26,19xM10
16UNC
A3 25x26,19x52,37x3/8-16UNC
M6 31x30,18x58,72xM10

A4 31x30,18x58,72x7/16-14UNC M7 37,5x35,71x69,85xM12
37,5/27x35,71x69,85x1/2- 25x52,37x26,19xM8 deep12
A5 MF
13UNC Horiz
B7 20x40xM6
25/20x52,37x26,19xM10(=)
MG
BA 18x55xM8 - Special
BB 27x55xM8
31x30,18x58,72xM10 deep18
BC 36/27x55xM8 MH
(=)
C3 13,5x30xM6 31x30,18x58,72xM10 deep12
C7 20x40xM8 MN
(=)
CA 27x51xM10
37,5x35,71x69,85xM12
CD 36x62xM10 MR
CZ 27x51xM10(2 Vert.Holes) deep20 (=)
G7 20x40x5/16-18UNC - Special
GA 27x51x3/8-16UNC - Special
E5 7/8-14UNF
E6 1-1/16-12UN
E8 1-5/16-12UN
E9 1-5/8-12UN
EA 1-7/8-12UN
H8 M27x2-ISO6149
H9 M33x2-ISO6149
F5 BSP 3/4 GAS

F6 BSP 1 GAS

F7 BSP 1-1/4 GAS

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
58 GEAR MOTORS I TECHNICAL INFORMATION

A B C D E F G H I J K L M N 0
/

J Ports Pos & Spec Body

NN Std from catalogue

*PL Inlet port Left position looking gear drive from front flange
*PR Inlet port Right position looking gear drive from front flange
ZZ Port Bx-Bx in the center of the body - Option
* to be used if inlet-outlet are different

K Seals

N Standard NBR seals

B VITON seals - Option
D NBR seals + VITON shaft seal with dust lip
X NBR seals + Dust Cover - Option
Y VITON seals + Dust Cover - Option
Z VITON shaft seal + Dust Cover - Option

L Screws

N Std burnished screws

B Dacromet/Geomer - Anticorrosion screws

M Set valves
NNN No valve

N Type of mark

N Standard Turolla Marking

A Standard Turolla Marking+Customer Code-Special
Z Without Marking

O Mark position

N Std Marking position (on top)

A Special Marking position on the bottom

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 59

Motor performance graphs

The graphs on the next pages provide typical inlet flow and output power for Group 3
motors at various working pressures. Data were taken using ISO VG46 petroleum /mineral based fluid at 50 °C [122 °F] (vis-
cosity = 28 mm2/s [132 SUS]).

SNM3NN/022 motor performance graph SNM3NN/026 motor performance graph

SNM3NN/033 motor performance graph SNM3NN/038 motor performance graph

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
60 GEAR MOTORS I TECHNICAL INFORMATION

SNM3NN/044 motor performance graph SNM3NN/048 motor performance graph

SNM3NN/055 motor performance graph SNM3NN/063 motor performance graph

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 61

SNM3NN/075 motor performance graph

SNM3NN/090 motor performance graph

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
62 GEAR MOTORS I TECHNICAL INFORMATION

Flange, shaft and port configurations

Motor Code Flange Shaft Port

SNM3NN pilot Ø 50.8 mm

European flanged
SNU3NN 01BA [2.0 in] 1:8 tapered
port + pattern
SNM3GN European 01 4-bolt

SNM3NN pilot Ø 50.8 mm

European flanged
SNU3NN 02BA [2.0 in] 1:8 tapered
port + pattern
SNM3GN European 02 4-bolt

SNM3NN pilot Ø 60.3 mm

European flanged
SNU3NN 03BB [2.374 in] 1:8 tapered
port + pattern
SNM3GN European 03 4-bolt

SNM3NN pilot Ø 105 mm

German std ports
SNU3NN 06AA [4.133 in] 1:5 tapered
port X pattern
SNM3GN German 4-bolt

SNM3NN SAE B
Vertical four bolt
SNU3NN 07BC pilot Ø 101.6 1:8 tapered
flanged port
SNM3GN 2-bolt

SNM3NN pilot Ø 50.8 mm

Ø 20 mm [0.787 in] European flanged
SNU3NN 01FA [2.0 in]
parallel port + pattern
SNM3GN European 01 4-bolt

SNM3NN pilot Ø 50.8 mm

Ø 20 mm [0.787 in] European flanged
SNU3NN 02FA [2.0 in]
parallel port + pattern
SNM3GN European 02 4-bolt

SNM3NN pilot Ø 60.3 mm

Ø 22 mm [0.866 in] European flanged
SNU3NN 03FB [2.374 in]
parallel port + pattern
SNM3GN European 03 4-bolt

SNM3NN SAE B
Ø 22.225 mm [0.875 in] Vertical four bolt
SNU3NN 07GA pilot Ø 101.6 mm
parallel flanged port
SNM3GN 2-bolt

SNM3NN pilot Ø 50.8 mm Splined shaft

European flanged
SNU3NN 01DA [2.0 in] 13T – m 1.60
port + pattern
SNM3GN European 01 4-bolt DIN 5482 – B22 x 19

SNM3NN pilot Ø 50.8 mm Splined shaft

European flanged
SNU3NN 02DB [2.0 in] 13T – m 1.60
port + pattern
SNM3GN European 02 4-bolt DIN 5482 – B22 x 19

SNM3NN pilot Ø 105 mm Splined shaft

German std ports
SNU3NN 06DD [4.133 in] 15T – m 1.60
port X pattern
SNM3GN German 4-bolt DIN 5482 – B28 x 25

SNM3NN SAE B Splined shaft

Vertical four bolt
SNU3NN 07SA pilot Ø 101.6 mm SAE J498
flanged port
SNM3GN 2-bolt 13T – 16/32DP

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 63

Shaft and flange availability and torque capability

This table details the standard Group 3 shafts and flange combinations that are currently
available with the maximum shaft torque limits.

Shaft and flange availability and torque capability

Shaft Mounting flange code with maximum torque in Nm [lb•in]
Code Description 01 02 03 06 07
AA Taper 1:5-M16x1,5-Key 5 300 [2655]
BA Taper 1:8-M14x1,5-Key 4 350 [3097] 350 [3097]
BB Taper 1:8-M16x1,5-Key 4,79 500 [4425]
Taper 1:8-5/8-18UNF-2A-Key
BC 300 [2655]
6,375
Taper 1:8-M14x1,5-Key 4 +
BD 350 [3097] 350 [3097]
thd hole M8 - Special
"Taper 1:8-5/8-18UNF-2A-Key
BP 300 [2655]
6,375
with Nut & Washer (for flange
CA **
07)"
CB Tang 8xØ22,2 - Special **
DA Tang 12xØ24 - Special 290 [2566] 290 [2566]
DIN 5482 B22x19 L24 (for
DD 450 [3982]
flange typo 01)
DIN 5482 B28x25 L28 (for
FA 210 [1858] 210 [1858]
flange typo 06)
Parallel Ø20-Key 5x5 L30 (for
FB 300 [2655]
flange typo 01-02)
Parallel Ø22-Key 5x5 L40 (for
GA 230 [2035]
flange typo 03)
Parallel Ø22,225 x L25,4-Key
GB 230 [2035]
6,375x6,375 L25,4
"Parallel Ø22,225xL25,4-Key
GC 230 [2035]
6,375x6,375x25,4
with thd hole:1/4-20UNC-2B
SA 270 [2389]
"
"Parallel Ø22,225xL25,4-Key
SB 270 [2389]
6,375x6,375x25,4
with thd hole:5/16-
RA 400 [3540]
18UNC-2B - Special"
SH SAE J498-13T-16/32-SAE B 400 [3540]

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
64 GEAR MOTORS I TECHNICAL INFORMATION

Ports dimensions
Bidirectional motor ports
Available ports for Group 3 bidirectional motors

A B C D E F

45o
v

a g x d e f
b h y
c (4 holes min. full thd. i (4 holes min. full thd. z (4 holes min. full thd.
20 mm [0.787 in] deep) 20 mm [0.787 in] deep) 20 mm [0.787 in] deep)

Ports dimensions for bidirectional motors SNM3NN

Port type A B C D E F
Dimensions a b v c g h i x y z d e f
25.4 26.19 52.37 27 55 20 40 ¾ Gas
022 / –16UNC–2B
3 8 M8 M8 M26x1.5 15/16–12UN–2B
[1.0] [1.031] [2.061] [1.063] [2.165] [0.79] [1.58] (BSPP)
25.4 26.19 52.37 27 55 20 40 ¾ Gas
026 / –16UNC–2B
3 8 M8 M8 M26x1.5 15/16–12UN–2B
[1.0] [1.031] [2.061] [1.063] [2.165] [0.79] [1.58] (BSPP)
31.8 30.18 58.72 27 55 27 51 1 Gas
033 / –14UNC–2B
7 16 M8 M10 M33x2 15/8– 12UN–2B
[1.251] [1.188] [2.311] [1.063] [2.165] [1.063] [2.008] (BSPP)
31.8 30.18 58.72 27 55 27 51 1 Gas
038 / –14UNC–2B
7 16 M8 M10 M33x2 15/8–12UN–2B
[1.251] [1.188] [2.311] [1.063] [2.165] [1.063] [2.008] (BSPP)
31.8 30.18 58.72 27 55 27 51 1 Gas
Frame size

044 / –14UNC–2B
7 16 M8 M10 M33x2 15/8–12UN–2B
[1.251] [1.188] [2.311] [1.063] [2.165] [1.063] [2.008] (BSPP)
31.8 30.18 58.72 27 55 27 51 1 Gas
048 / –14UNC–2B
7 16 M8 M10 M33x2 15/8–12UN–2B
[1.251] [1.188] [2.311] [1.063] [2.165] [1.063] [2.008] (BSPP)
31.8 30.18 58.72 27 55 27 51 1 Gas
055 / –14UNC–2B
7 16 M8 M10 M33x2 15/8–12UN–2B
[1.251] [1.188] [2.311] [1.063] [2.165] [1.063] [2.008] (BSPP)
31.8 30.18 58.72 36 55 36 62 1¼ Gas
063 / –14UNC–2B
7 16 M8 M10 M33x2 15/8–12UN–2B
[1.251] [1.188] [2.311] [1.417] [2.165] [1.417] [2.441] (BSPP)
31.8 30.18 58.72 36 55 36 62 1¼ Gas
075 / –14UNC–2B
7 16 M8 M10 M33x2 15/8–12UN–2B
[1.251] [1.188] [2.311] [1.417] [2.165] [1.417] [2.441] (BSPP)
31.8 30.18 58.72 36 55 36 62 1¼ Gas
090 / –14UNC–2B
7 16 M8 M10 M33x2 15/8–12UN–2B
[1.251] [1.188] [2.311] [1.417] [2.165] [1.417] [2.441] (BSPP)
Drain M14 x 1.5 9/16–18UNF–2B

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 65

Unidirectional motor ports

Available ports for Group 3 unidirectional motors

A B C D E

45o
v

a g x d e
b h y
c (4 holes min. full thd. i (4 holes min. full thd. z (4 holes min. full thd.
20 mm [0.787 in] deep) 20 mm [0.787 in] deep) 20 mm [0.787 in] deep)

Ports dimensions for unidirectional motors SNU3NN

Port type A B
Dimensions a b c v g h i
Outlet 20 [0.79] 40 [1.58] M8 3/8–16UNC–2B 27 [1.063] 55 [2.165] M8
022 3/8–16UNC–2B
Inlet 20 [0.79] 40 [1.58] M8 18 [0.709] 55 [2.165] M8
Outlet 20 [0.79] 40 [1.58] M8 3/8–16UNC–2B 27 [1.063] 55 [2.165] M8
026 3/8–16UNC–2B
Inlet 20 [0.79] 40 [1.58] M8 18 [0.709] 55 [2.165] M8
Outlet 27 [1.063] 51 [2.008] M10 7/16–14UNC–2B 27 [1.063] 55 [2.165] M8
033 3/8–16UNC–2B
Inlet 20 [0.79] 40 [1.58] M8 18 [0.709] 55 [2.165] M8
Outlet 27 [1.063] 51 [2.008] M10 7/16–14UNC–2B 27 [1.063] 55 [2.165] M8
038 3/8–16UNC–2B
Inlet 20 [0.79] 40 [1.58] M8 18 [0.709] 55 [2.165] M8
Outlet 27 [1.063] 51 [2.008] M10 7/16–14UNC–2B 27 [1.063] 55 [2.165] M8
Frame size

044 3/8–16UNC–2B
Inlet 27 [1.063] 51 [2.008] M10 18 [0.709] 55 [2.165] M8
Outlet 27 [1.063] 51 [2.008] M10 7/16–14UNC–2B 27 [1.063] 55 [2.165] M8
048 3/8–16UNC–2B
Inlet 27 [1.063] 51 [2.008] M10 18 [0.709] 55 [2.165] M8
Outlet 27 [1.063] 51 [2.008] M10 ½–13UNC–2B 27 [1.063] 55 [2.165] M8
055 7/16–14UNC–2B
Inlet 27 [1.063] 51 [2.008] M10 18 [0.709] 55 [2.165] M8
Outlet 36 [1.417] 62 [2.441] M10 ½–13UNC–2B 36 [1.417] 55 [2.165] M8
063 7/16–14UNC–2B
Inlet 27 [1.063] 51 [2.008] M10 27 [1.063] 55 [2.165] M8
Outlet 36 [1.417] 62 [2.441] M10 ½–13UNC–2B 36 [1.417] 55 [2.165] M8
075 7/16–14UNC–2B
Inlet 27 [1.063] 51 [2.008] M10 27 [1.063] 55 [2.165] M8
Outlet 36 [1.417] 62 [2.441] M10 ½–13UNC–2B 36 [1.417] 55 [2.165] M8
090 7/16–14UNC–2B
Inlet 27 [1.063] 51 [2.008] M10 27 [1.063] 55 [2.165] M8

(the table is continued on the next page)

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
66 GEAR MOTORS I TECHNICAL INFORMATION

Unidirectional motor ports

Available ports for Group 3 unidirectional motors

A B C D E F

45o

a g x d e f
b h y
c (4 holes min. full thd. i (4 holes min. full thd. z (4 holes min. full thd.
20 mm [0.787 in] deep) 20 mm [0.787 in] deep) 20 mm [0.787 in] deep)

Ports dimensions for unidirectional motors SNU3NN

Port type C D E F
Dimensions x y z d e f
Outlet 20 [0.79] 40 [1.58] M8 M26 x 1.5 ¾ Gas (BSPP) 15/16–12UN–2B
022
Inlet 20 [0.79] 40 [1.58] M8 M26 x 1.5 ¾ Gas (BSPP) 11/16–12UN–2B
Outlet 20 [0.79] 40 [1.58] M8 M26 x 1.5 ¾ Gas (BSPP) 15/16–12UN–2B
026
Inlet 20 [0.79] 40 [1.58] M8 M26 x 1.5 ¾ Gas (BSPP) 11/16–12UN–2B
Outlet 27 [1.063] 51 [2.008] M10 M33x2 1 Gas (BSPP) 15/8–12UN–2B
033
Inlet 20 [0.79] 40 [1.58] M8 M26 x 1.5 ¾ Gas (BSPP) 15/16–12UN–2B
Outlet 27 [1.063] 51 [2.008] M10 M33x2 1 Gas (BSPP) 15/8–12UN–2B
038
Inlet 20 [0.79] 40 [1.58] M8 M26 x 1.5 ¾ Gas (BSPP) 15/16–12UN–2B
Outlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/8–12UN–2B
Frame size

044
Inlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/16–12UN–2B
Outlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/8–12UN–2B
048
Inlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/16–12UN–2B
Outlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 17/8–12UN–2B
055
Inlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/8–12UN–2B
Outlet 36 [1.417] 62 [2.441] M10 M42 x 2 1¼ Gas (BSPP) 17/8–12UN–2B
063
Inlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/8–12UN–2B
Outlet 36 [1.417] 62 [2.441] M10 M42 x 2 1¼ Gas (BSPP) 17/8–12UN–2B
075
Inlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/8–12UN–2B
Outlet 36 [1.417] 62 [2.441] M10 M42 x 2 1¼ Gas (BSPP) 17/8–12UN–2B
090
Inlet 27 [1.063] 51 [2.008] M10 M33 x 2 1 Gas (BSPP) 15/8–12UN–2B

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 67

Anti-cavitation check valve – SNM3GN

SNM3GN
Turolla offers an optional integral anti-cavitation check valve integrated in Group 3 motors
bearing blocks. Available for all the displacements, the valve directs internally the flow from the
motor outlet to the inlet, when the outlet pressure gets higher then the inlet one.

Valve schematic diagram Anticavitation check valve cross section

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
68 GEAR MOTORS I TECHNICAL INFORMATION

Dimensions

SNM3NN, SNU3NN – 01FA, 01DA and 01BA

Standard porting drawing for 01FA, 01DA and 01BA
mm
[in]
01FA 01DA 01BA
46.5 [1.83] B max
20 [0.787] A ±0.75 [±0.03]

46 14.5 [0.571] 24 8 [0.314]

(54.3 [2.137])
[1.118] 34 [0.944] 115 ±0.25 [4.527 ±0.010]

42.9 [1.689]
40 6 Distance from [1.338] -0.076
Ø 50.8 -0.030
5 Distance from 5 [0.196] 22 [0.866]
-0.003 ]

Ø 22 [0.866]
[1.574] [0.24] front flange [2.0 -0.001
[0.196] front flange

M14x1.5-6g
to shoulder to shoulder

A B

150.5 [5.925] max

148 [ 5.826] max
(128.1 [5.043])
A

85.2 [3.354]

(96.2 [3.787])
B
]
Ø 21.5 -0.130
[0.846 -0.005
[0.787-0.0008 ]

24 [0.944]
[0.874 ±0.020]
0

M8 (full thd 18 [0.708] deep)

0

X
22.22 ±0.50
0

44.44 ±0.75 [1.749 ±0.03]

1:8

Spline:
Ø 20 -0.021

A-A
0

B22x19 DIN 5482 C/c

0 0
5 -0.030 [0.196-0.001 ] (Profile offset -0.10 [0.024])
M14x1.5-6H
M8 (full thd 12 [0.472] deep) E/e Drain port
M10 (full thd 17 [0.669] deep)
Nut and washer supplied with pump < 40: ±0.20 [0.008] D/d 11.0-11.5 [0.433-0.453]
-0.20 [0.866 -0.008 ]

Recommended tightening torque: 75-85 Nm

+0.004

> 40: ±0.25 [0.010]

Ø0.75 [0.030] X
98.4 [3.874]
B-B
0 0 121.5 [4.783] max
4 -0.030 [0.158 -0.001]
22 +0.10

11.5 +0.30 +0.010

-0.10 [0.453 -0.004 ]

Bidirectional motors dimensions – 01FA, 01DA and 01BA*

Frame size 022 026 033 038 044 048 055 063 075 090
63.0 64.5 67.0 68.8 71.0 72.5 75.0 78.0 82.0 87.0
A
[2.480] [2.539] [2.637] [2.708 [2.795] [2.854] [2.952] [3.070] [3.228] [3.425]
Dimension
132.5 135.5 140.5 144.0 148.5 151.5 156.5 162.5 170.5 180.5
B
[5.216] [5.334] [5.531] [5.669] [5.846] [5.964] [6.161] [6.397] [6.712] [7.106]
C/c 20 [0.79] 27 [1.063]
Inlet/Outlet D/d 40 [1.58] 51 [2.007]
E/e M8 M10

* For unidirectional SNU3NN dimensions, see SNU3NN ports, pages 65 and 66.

For unidirectional motors no case drain hole into the rear cover.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
01FA SNM3NN/075BN01FAM1CACANNNN/NNNNN 210 N•m [1858 lb•in]
01DA SNM3NN/026BN01DAM1C7C7NNNN/NNNNN 290 N•m [2566 lb•in]
01BA SNM3NN/044BN01BAM1CACANNNN/NNNNN 350 N•m [3097 lb•in]

For further details on ordering, see Model Code, pages 54-58.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 69

SNM3NN, SNU3NN – 02FA, 02DB and 02AA

Standard porting drawing for 02FA, 02DB and 02AA
mm
02FA 02DA 02BA [in]

46.5 [1.83] B max

20 [0.787] A ±0.75 [±0.03]
14.5 [0.571] 24 8 [0.314]

58 [2.28] max
[0.944]
46 [1.118] 34 [1.338] 124.5 [4.9] max
-0.076
Ø 50.8 -0.030
5 [0.196] 22 [0.866]

45 [1.77]
-0.003 ]
98.4 [3.87]

Ø 22 [0.866]
40 [1.574] 6 [0.236] Distance from 5 [0.196] Distance from [2.0 -0.001

M14x1.5-6g
front flange front flange
to shoulder to shoulder
A B

148 [ 5.826] max

163 [6.42] max

(137 [5.39])
A B

105 [4.13] max

]
Ø 21.5 -0.130
[0.846 -0.005

92 [3.62]
[0.787-0.0008 ]

24 [0.944]
0

M8 (full thd 18 [0.708] deep) X

0

[0.874 ±0.02]
22.22 ±0.50

44.44 ±0.75 [1.749 ±0.03]

0

1:8

Spline:
Ø 20 -0.021

A-A
0

B22x19 DIN 5482 C/c

0 0
5 -0.030 [0.196-0.001 ] (Profile offset -0.10 [0.024]) M14x1.5-6H
M8 (full thd 12 [0.472] deep) E/e Drain port
M10 (full thd 17 [0.669] deep)
Nut and washer supplied with pump
Recommended tightening torque: 75-85 Nm < 40: ±0.20 [0.008] D/d
115 ±0.25 [4.527 ±0.010]
-0.20 [0.866 -0.008 ]
+0.004

> 40: ±0.25 [0.010]

B-B body width
0 0
4 -0.030 [0.158 -0.001]
11.0-11.5 [0.433-0.453]
Ø0.75 [0.030] X
22 +0.10

11.5 +0.30 +0.010

-0.10 [0.453 -0.004 ]

Bidirectional motors dimensions – 02FA, 02DA and 02BA*

Frame size 022 026 033 038 044 048 055 063 075 090
63.0 64.5 67.0 68.8 71.0 72.5 75.0 78.0 82.0 87.0
A
[2.480] [2.539] [2.637] [2.708 [2.795] [2.854] [2.952] [3.070] [3.228] [3.425]
Dimension
132.5 135.5 140.5 144.0 148.5 151.5 156.5 162.5 170.5 180.5
B
[5.216] [5.334] [5.531] [5.669] [5.846] [5.964] [6.161] [6.397] [6.712] [7.106]
C/c 20 [0.79] 27 [1.063]
Inlet/Outlet D/d 40 [1.58] 51 [2.007]
E/e M8 M10

* For unidirectional SNU3NN dimensions, see SNU3NN ports, pages 65 and 66.

For unidirectional motors no case drain hole into the rear cover.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
02FA SNM3NN/044BN02FAM1CACANNNN/NNNNN 210 N•m [1858 lb•in]
02DA SNM3NN/033BN02DAM1CACANNNN/NNNNN 290 N•m [2566 lb•in]
02BA SNM3NN/026BN02BAM1C7C7NNNN/NNNNN 350 N•m [3097 lb•in]

For further details on ordering, see Model Code, pages 54-58.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
70 GEAR MOTORS I TECHNICAL INFORMATION

SNM3NN, SNU3NN – 03FB and 03BB

Standard porting drawing for 03FB and 03BB
mm
03FB 03BB [in]

60 [2.362] B max

28.5 [1.122] A ±0.75 [±0.030]

146.5 [5.768] max

65.5 [2.578] max

17.5 [0.689] 28 14.5 [0.571] Distance from front flange
to cone reference diameter 114.3 [4.5]
[1.102]
59 [2.323]
8 [0.315] 22 [0.866]
50 [1.968] 9 [0.354] Distance from X
Ø 25 [0.984]
M16x1.5-6g

front flange
to shoulder B

[ 1.949]
A

49.5

148 [ 5.826] max

181.5 [ 7.145] max

(149.5 [ 5.885])
A

100 [ 3.937]

116 [4.566] max

[0.866 -0.0008 ]

M8 (full thd 18 [0.708] deep)

22.22 ±0.50 [0.875 ±0.020]

B
-0.076 [2.374 -0.003 ]
0

1:8
-0.012

C/c

44.44 ±0.75 [1.749 ±0.03]

Ø 22 -0.021

Torque for nut: 95-105 Nm

Ø60.3 -0.030
0

A-A
0 0
5 -0.030 [0.196-0.001 ] M10 (full thd 17 [0.669] deep) E/e
M14x1.5-6H
D/d ±0.25 [±0.010] Drain port
B-B
4.79 -0.30
0 115 ±0.25[4.527 ±0.010]
24 +0.10 +0.004
-0.20 [0.945 -0.008 ] 0
[0.189 -0.012 ] body width

11.0-11.5 [0.433-0.453]
Ø0.75 [0.030] X
+0.15
13.5 -0.25 [0.532 +0.006
-0.010 ]

Bidirectional motors dimensions – 03FB and 03BB*

Frame size 022 026 033 038 044 048 055 063 075 090
61 63 64.5 66.5 69.5 72.5 75 78 82 87
A
[2.4] [2.48] [2.54] [2.62] [2.74] [2.854] [2.95] [3.07] [3.23] [3.43]
Dimension
132.5 135.5 140.5 144.0 148.5 151.5 156.5 162.5 170.5 180.5
B
[5.22] [5.33] [5.53] [5.67] [5.85] [5.96] [6.16] [6.4] [6.71] [7.11]
C/c 18 [0.71] 27 [1.063]
Inlet/Outlet D/d 55 [2.16]
E/e M8

* For unidirectional SNU3NN dimensions, see SNU3NN ports, pages 65 and 66.

For unidirectional motors no case drain hole into the rear cover.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
03FB SNM3NN/063BN03FBM1CACANNNN/NNNNN 300 N•m [2655 lb•in]
03BB SNM3NN/090BN03BBM1CACANNNN/NNNNN 500 N•m [4425 lb•in]

For further details on ordering, see Model Code, pages 54-58.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 71

SNM3NN, SNU3NN – 06AA

Standard porting drawing for 06AA
mm
06DD 06AA [in]
51 [2.007] B max
-0.003 ]
-0.001

23.5 [0.925] A ±0.75 [±0.03]

58.5 [2.303] max

-0.036 [4.133

15 [0.590] 25 11 [0.433] 115 ±0.25 [4.527 ±0.010]

40 [1.574] [0.984] body width
Ø105 -0.090

8 [0.314] 22 [0.866]
7 [0.275] Distance from front
Ø 25 [0.984]

flange to shoulder
M16x1.5-6g

48 [1.889]
A
o
45

166.5 [ 6.555] max

148 [ 5.826] max
(145 [5.708])

108 [4.251] max

28 [1.102] A

97 [3.818]
[0.874 ±0.020]
22.22 ±0.50

44.44 ±0.75 [1.749 ±0.03]

C/c
]
Ø 27.5 -0.130
[1.082 -0.005

1:5
0
0

X
Spline:
B28x25 DIN 5482 M8 (full thd 12 [0.472] deep) E/e M14x1.5-6H
(Profile offset: 0.202 [0.008])
D/d ±0.25 [0.010] Drain port

Torque for nut: 95-105 Nm 11.0-11.5 [0.433-0.453]

A-A Ø0.75 [0.030] X
0 0
5 -0.030 [0.196-0.001 ] 102.0 [4.015]

+0.30 +0.010
13.0 -0.10 [0.512 -0.004 ] 123.5 [4.862] max

Bidirectional motors dimensions – 06DD AND 06AA *

Frame size 022 026 033 038 044 048 055 063 075 090
63.0 64.5 67.0 68.8 71.0 72.5 75.0 78.0 82.0 87.0
A
[2.480] [2.539] [2.637] [2.708 [2.795] [2.854] [2.952] [3.070] [3.228] [3.425]
Dimension
132.5 135.5 140.5 144.0 148.5 151.5 156.5 162.5 170.5 180.5
B
[5.216] [5.334] [5.531] [5.669] [5.846] [5.964] [6.161] [6.397] [6.712] [7.106]
C/c 20 [0.79] 27 [1.063]
Inlet/Outlet D/d 40 [1.58] 51 [2.007]
E/e M8 M10

* For unidirectional SNU3NN dimensions, see SNU3NN ports, pages 65 and 66.

For unidirectional motors no case drain hole into the rear cover.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
06DD SNM3NN/044BN06DDM1BBBBNNNN/NNNNN 300 N•m [2655 lb•in]
06AA SNM3NN/022BN06AAM1BABANNNN/NNNNN 450 N•m [3982 lb•in]

For further details on ordering, see Model Code, pages 54-58.

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
72 GEAR MOTORS I TECHNICAL INFORMATION

SNM3NN, SNU3NN – 07BC, 07SA and 07GA

Standard porting drawing for 07BC, 07SA and 07GA
mm
07BC 07SA 07GA [in]

B max 41.2 [7.622] 176.5 [6.948] max

59.4 [2.338]
41.2 [7.622] A ±0.75 [±0.03] 146.05 [5.75]
42.9 [1.689]
7.9 [0.311] 33.3 [1.311] 7.9 [0.311] 33.3 [1.311] R 61 [2.402] max
7.9 [0.311] 28.4 [1.118]
Distance from
Distance from front flange 25.0 [0.984] 13.5 [0.531] 9.5 [0.374]
23.1 [0.909]
±0.25 [0.010]
front flange to shoulder
to shoulder
B Ø 4 ±0.1[0.157 ±0.004] A
E/e

Ø 101.6 -0.05
0

157 [ 6.181] max

[4.0 -0.002
0
]
14.15-14.75 [0.557-0.580]
5/8-18UNF-2A

Cone reference diameter

[0.858 -0.005 ]

B A

Ø 22.225 -0.025

22.22 ±0.50 [0.874 ±0.020]

]
0

[0.875 -0.001
0

44.44 ±0.75 [1.749 ±0.03]

1:8

0
Ø 22.225 [0.875]

0 0
Ø21.806 -0.127

C/c -1.5 [0.059]

0

6.35-5.25 [0.25-0.206]
X
F/f (full thd 20 [0.787] deep)
Splined:

X
SAE J498-13T-16/32DP D/d ±0.25 [0.01]

Ø0.75 [0.03]
B-B Flat root side fit 9/16-18UNF-2B
(circular tooth thickness Drain port
0 0
6.375-0.025 [0.250-0.001] 0.127 [0.005] less than
standard class 1 fit) 115 ±0.25 [4.527 ±0.01]
A-A
body width
0 0
6.375-0.025 [0.250-0.001]

3.33-3.07 [0.131-0.12]

24.76-25.07 [0.974-0.987]

Bidirectional motors dimensions – 07BC, 07SA and 07GA*

Frame size 022 026 033 038 044 048 055 063 075 090
63.0 64.5 67.0 68.8 71.0 72.5 75.0 78.0 82.0 87.0
A
[2.480] [2.539] [2.637] [2.708 [2.795] [2.854] [2.952] [3.070] [3.228] [3.425]
Dimension
132.5 135.5 140.5 144.0 148.5 151.5 156.5 162.5 170.5 180.5
B
[5.216] [5.334] [5.531] [5.669] [5.846] [5.964] [6.161] [6.397] [6.712] [7.106]
C/c 25.4 [1] 31.8 [1.251]
D/d 26.19 [1.031] 30.18 [1.188]
Inlet/Outlet
E/e 52.37 [2.061] 58.72 [2.311]
F/f 3/8–16UNC–2B 7/16–14UNC–2B

* For unidirectional SNU3NN dimensions, see SNU3NN ports, pages 65 and 66.

For unidirectional motors no case drain hole into the rear cover.

Model code examples and maximum shaft torque

Flange/drive gear Model code example Maximum shaft torque
07BC SNM3NN/026BN07BCM6A3A3NNNN/NNNNN 300 N•m [2655 lb•in]
07SA SNM3NN/063BN07SAM6A4A4NNNN/NNNNN 270 N•m [2389 lb•in]
07GA SNM3NN/090BN07GAM6A4A4NNNN/NNNNN 230 N•m [2035 lb•in]

For further details on ordering, see Model Code, pages 54-58.

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS I TECHNICAL INFORMATION 73

Notes

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
74 GEAR MOTORS - Group 1 I TECHNICAL INFORMATION

Notes

Turolla - L1016082 • September 2013 • Rev C

 GEAR MOTORS - Group 1 I TECHNICAL INFORMATION 75

Notes

Turolla - L1016082 • September 2013 • Rev C

66M 77C 50C

88Y 55K
33M 100Y

66M
88Y
 Local address

Italy
Orange - CMYK 88%Y 66%M
Grey - CMYK 44% Black

Via Villanova 28
40055 Villanova di Castenaso
Bologna, Italia
Telephone: +39 051 6054 411

U.S.A.
2800 East 13th Street
Ames, IA 50010, USA
Phone: +1 515 239 6677
Fax: +1 515 239 6618

Slovakia
Kukučínova 2148-84
01701 Považská Bystrica, Slovakia
Phone: +421 424 301 202
Fax: +421 424 301 626

E-mail: [email protected]
www.turollaocg.com