Scribd
Upload
335 views2 pages

Fiat/Alfa Romeo Immo Emulator Guide

The document provides an installation guide for an EML921/603 immobilizer emulator for all Fiat and Alfa Romeo cars, noting it requires connection to +12V, ground, and the K-Line data wire after the ignition switch. The guide explains that the emulator LED will blink three times upon a successful code learning procedure and notes the installation process involves clearing the original immobilizer code from the ECU memory first before connecting the emulator.

Uploaded by

Motor Csillag
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
335 views2 pages

Fiat/Alfa Romeo Immo Emulator Guide

The document provides an installation guide for an EML921/603 immobilizer emulator for all Fiat and Alfa Romeo cars, noting it requires connection to +12V, ground, and the K-Line data wire after the ignition switch. The guide explains that the emulator LED will blink three times upon a successful code learning procedure and notes the installation process involves clearing the original immobilizer code from the ECU memory first before connecting the emulator.

Uploaded by

Motor Csillag
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Fiat / Alfa Romeo immobilizer emulator EML921/603 installation guide

2014.10.20 edition 01

EML921/60.3 technical data:


EML 921
Supply voltage: 10-15V (DC)
Fiat immo Data baud rate: 4800 kbps
ID:60.3 Supported cars: All Fiat, Alfa Romeo cars with
black, yellow, grey and blue immo box
+12V K-Line
GND
Wiring description:

[+12V] - power supply after ignition switch (Terminal 15)


LED indicator [K-Line] - Data wire, connected to ECU .

[GND] - Ground.

[!] Emulator supply must be switched in the same time with engine ECU
ignition supply.

LED indicator after ignition “on”:

LED still off Incorrect connection, bad power supply of ECU,


broken ECU, short immo line, connected immobilizer
box (original immobilizer box must be disconnected)

LED go on and after few Normal condition


seconds goes out
LED go on and after few Incorrect ECU immobilizer code
seconds start blinking
LED go on and after few Recognized NEW ECU, code learning procedure
seconds blink three times completed.
and goes out

Installation procedure:

1. Make ECU in NEW state (clear old immobilizer data in ECU memory (eeprom or MCU)). How to change data in
ECU for most popular ECU’s see dump examples below, also you can use software’s like as “immo killer” and etc.
2. Connect emulator: GND – connect to ground, +12V – connect to ignition, K-Line – connect to ECU immobilizer
wire.
3. Disconnect immobilizer box, or cut immobilizer wire between ECU and immo box.
4. Switch ignition “ON” , and wait few seconds while LED indicator go on and after few seconds blink fast three times
(it’s mean “correct learning procedure completed”).
5. Start engine and Enjoy!
Most popular dump examples how to made ECU in NEW state:

Fiat Ducato, Peugeot Boxer 2.0L Jtd, 2.8L Jtd Bosch ECU (2 connectors, eeprom 95080)
Immo line PIN 11

Change data in eeprom like shown in example (yellow marked with black) adr.: 0x180h-0x18Fh

Alfa Romeo 2.4L Jtd, Bosch ECU (5 connectors, eeprom 24C04)


Immo line PIN 13, connector C (middle connector)

Change data in eeprom like shown in example (yellow marked with black) adr.: 0x1EAh-0x1F8h

You might also like