Scribd
Upload
698 views3 pages

Masterseal 915 Tds PDF

Uploaded by

Mohamed Ahmed Rezk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
698 views3 pages

Masterseal 915 Tds PDF

Uploaded by

Mohamed Ahmed Rezk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

MasterSeal® 915 (Formerly known as Masterflow 410)

High strength, free-flowing epoxy grout

DESCRIPTION OF PRODUCT TYPICAL PROPERTIES


The product is three component and easily mixed on
site to a pourable consistency. MasterSeal 915 is Pot life: at 25°C 50 minutes
suitable for an application thickness range of 10- Compressive 24 hrs 100N/mm²
80mm where high flow characteristics are required. strength
BS 6319 Part 2:
Where greater thicknesses are required, pour in two Flexural strength 40N/mm²
sections leaving 6 hours between each pour or BS 6319 Part 3:
consider the use of MasterFlow 640. Density: 2000kg/m³
Full chemical at 25°C 7 days
cure: at 40°C 3 days
TYPICAL APPLICATIONS
 Anchors and fixing bolts
PACKAGING
 Crane and transporters rails
MasterSeal 915 is supplied in 10kg units.
 New and old machine base plates
 Structural filling of holes and cavities in COMPOSITION
concrete Bisphenol A epoxy resin base is a low viscosity liquid
 Industrial equipment and machinery subject to reactor which when mixed with the inert aggregate
static or dynamic forces forms an easily pourable and mobile grout.
 Equipment where chemical and acid spillage
occurs CHEMICAL RESISTANCE
 Pile cap waterproofing (at >20mm thickness) The resistance of MasterSeal 915 to most common
 Steel columns for warehouses corrosive chemicals is excellent:
 Dilute and concentrated alkalis
ADVANTAGES  Most dilute acids
 No priming required  Oil and petrol
 High tensile, flexural and compressive strength  Ammonia
 Excellent adhesion to steel and concrete  Formaldehyde
 Rapid installation and strength gain to ensure  Saline solutions
early commissioning of equipment  Mineral oil, vegetable and animal fats
 Excellent fatigue resistance
 Compatibility with equipment subject to APPLICATION PROCEDURE SURFACE
extensive thermal movement PREPARATION:
 High resistance to dynamic loads and chemical As with all epoxy resin applications, the quality of
attack surface preparation has a direct effect on the
 Non-shrink and tolerant to damp surfaces performance and durability of the system. Concrete
surfaces should be sound, dimensionally stable,
clean, free from laitance, paint, oil, grease, mould
release agent and residual curing compound. Metal
surfaces or components to be bedded should be free
from any rust or scaling. Formwork, if used, should
be wrapped in polythene to ensure a clean release.
MasterSeal® 915 (Formerly known as Masterflow 410)

MIXING: STORAGE
Do not split packs or alter the ratio of resin Store under cover, out of direct sunlight and protect
components in any way. Mix with a slow speed drill from extremes of temperature. In tropical climates,
the product must be stored in an air-conditioned
and paddle. Add the contents of the reactor
environment. Failure to comply with the
container to the base component in a suitable mixing
recommended storage conditions may result in
vessel, ensuring complete transfer of both resin
premature deterioration of the product or packaging.
components.
Mix for one minute before slowly adding the
For specific storage advice, consult BASF's
aggregate and continue mixing until a flowing,
Technical Services Department.
pourable consistency is achieved. Do not over-mix,
as that may entrain air.
SHELF LIFE
Up to 12 months when stored in unopened
PLACING:
containers according to manufacturer’s instructions.
Place immediately after mixing, into the prepared
area in such a manner that it has the shortest
SAFETY PRECAUTIONS
distance to flow. For longer pours, a suitable head of
As with all chemical products, care should be taken
pressure may be required. Ensure the area to be
during use and storage to avoid contact with eyes,
grouted is not completely sealed, and any displaced
mouth, skin and foodstuffs (which can also be
air can be expelled. Pour continuously from one end
tainted with vapour until product has fully cured or
only. Allow the grout to set prior to removal of
dried). Treat splashes to skin and eyes immediately.
formwork (normally after 6 hours). Where placement
If accidentally ingested, seek medical attention. Re-
exceeds depths of 80mm, application should be
seal containers after use. For specific storage and
carried out in layers. The second layer is to be
disposal instructions, refer to the material safety data
applied after 6 hours.
sheet.
REQUEST AND REFER TO RECOMMENDED
LIMITATIONS INSTALLATION PROCEDURES FOR MasterFlow
Do not apply MasterSeal 915 when the contact EPOXY GROUTS PRIOR TO USE
surfaces are less than 10°C. If the ambient
temperature is less than 10°C, then artificial heating NOTE
may be used. Field service, where provided, does not constitute
supervisory responsibility. For additional information,
EQUIPMENT CARE contact your local BASF representative.
Clean all equipment promptly with solvent. Any BASF reserves the right to have the true cause of
excess cured material will have to be mechanically any difficulty determined by accepted test methods.
removed.

YIELD
10kg of MasterSeal 915 will yield 5ltr.
MasterSeal® 915 (Formerly known as Masterflow 410)

QUALITY STATEMENT
All products manufactured by BASF Egypt, or
imported from BASF affiliate companies world-wide,
are manufactured to procedures certified to conform
to the quality, environment, health & safety
management systems described in the ISO
9001:2008, ISO 14001:2004 & OHSAS 18001:2007
standards.

* Properties listed are based on laboratory controlled tests .

® = Registered trademark of the BASF-Group in many countries

BASF_CC-GE/Seal_915_09_10/v1/06_14

You might also like