Pump size & type / Stages : 12EHM /9
Based on curve no. : EC-2657
Impeller diameter : 9.25 in
Customer : Eduin Moreno Capacity : 1400.0 USgpm
Item number : Booster Inyección Castilla II Head : 520.60 ft
Service : Agua Density / Specific gravity : - / 1.000
Flowserve reference : 2404455269 Pump speed : 1785 rpm
Date : February 27, 2020 Ns / Nss : 2964 / 9250 (US units)
Test tolerance : ANSI/HI 14.6 Grade 1B
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Bowl performance shown below is corrected for materials, viscosity and construction.
Bowl head of 522.1 ft corresponds with 520.6 ft head at discharge flange adjusted for elevation and friction losses.
Copyright © 2016 Flowserve. All rights reserved. Affinity v2.16.0
Hydraulic Datasheet
Customer : Eduin Moreno Pump / Stages : 12EHM /9
Customer reference : Bomba Booster Based on curve no. : EC-2657
Item number : Booster Inyección Castilla II Flowserve reference : 2404455269
Service : Agua Date : February 27, 2020
Operating Conditions Materials / Specification
Capacity : 1400.0 USgpm Material column code : B30
Water capacity (CQ=1.00) :-
Normal capacity :- Other Requirements
Total developed head : 520.60 ft Hydraulic selection : No specification
Water head (CH=1.00) :- Construction : No specification
NPSH available (NPSHa) @ Suction flange : 57.0 ft Test tolerance : ANSI/HI 14.6 Grade 1B
NPSHa less NPSH margin @ Impeller eye :- Driver Sizing : Max Power(MCSF to EOC) using SF
Maximum suction pressure : 10.0 psig Seal configuration : Packing
Rated suction pressure : 10.0 psig
Liquid
Liquid type : Other
Liquid description : Agua de Inyección
Temperature / Specific gravity : 180 °F / 1.000
Viscosity / Vapor pressure : 0.35 cSt / -
Performance
Pump speed : 1785 rpm Impeller diameter : Rated / Maximum / Minimum
NPSH required (NPSH3) @ Impeller eye : 14.1 ft : 9.25 in / 9.33 in / 8.44 in
Hydraulic power : 184 hp Impeller diameter ratio (rated/max) : 99.1 %
Efficiency (Pump overall / Bowl) (CE=1.00) : 81.6 % / 81.9 % Maximum head at rated diameter : 762.50 ft
Power (rated/max) : 226 hp / 226 hp Head rise to shut off : 46.0 %
Driver power rating : 250 hp / 186 kW Total head ratio (rated / max) / (max / rated) : 93.9 % / 106.5 %
Bowl pressure : 330.1 psig Flow at BEP : 1351.1 USgpm
(based on shut off @ cut dia/rated SG) Flow as % of BEP : 103.6 %
Maximum allowable : 431.0 psig Minimum continuous flow : 546.0 USgpm
Bowl & column hydrotest : 412.6 psig Thrust - Rated flow / Rated suction : 4129.7 lbf
Dischg Head Dischg Region MAWP : 490.0 psig Max thrust - Shut off / Rated suction : 5927.9 lbf
Ns / Nss : 2964 / 9250 (US units) Min thrust - Runout flow / Max Suction : 2724.4 lbf
Suction Regions MAWP : 265.0 psig (A negative thrust value indicates an upthrust condition)
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Bowl performance shown below is corrected for materials, viscosity and construction.
Bowl head of 522.1 ft corresponds with 520.6 ft head at discharge flange adjusted for elevation and friction losses.
Copyright © 2016 Flowserve. All rights reserved. Affinity v2.16.0
Construction Datasheet
Customer : Eduin Moreno Pump
Pump
/ Stages
/ Stages : 12EHM /9
Customer reference : Bomba Booster Based on curve no. : EC-2657
Item number : Booster Inyección Castilla II Flowserve reference : 2404455269
Service : Agua Date : February 27, 2020
: February 27, 2020
Construction Driver Information
Bowl construction / lined : Flanged - Std Wall / Line... Manufacturer : Flowserve Choice
Impeller type : Enclosed Power / SF (Req' / Act') : 250 hp / 186 kW / 1.0 / 0.0
Impeller fastening : Colleted Vertical shaft type : Hollow
Column construction : Flanged Driver type : NEMA Electric Motor
Column flange spec'n : Taneytown Specification Frame size / Base dia :-
Column dia (nominal) : 8.00 in Enclosure :-
Column pipe length : 0.75 ft Duty type
Column section length : 60.00 in Efficiency type
Lineshaft brg spacing : 60.00 in Hazardous area class :-
Lineshaft diameter : 1.69 in Explosion 'T' rating :-
Lineshaft coupling type : Threaded coupling Volts / Phase / Hz : 480 / - / 60 Hz
Lineshaft bearings, qty :1 Amps-full load/locked rotor :-/-
Lineshaft construction : Open Motor starting : Direct on line (DOL)
Lineshaft lubrication : Pumpage Insulation :-
Disch size/rating/face : 8 in / 300 lb ANSI / RF Temperature rise :-
"TF" - Fab'd / Above grade Suct and Dischg Bearings / Lubrication :-/-
Thrust stand size :- Motor mounted by : Customer
Motor Thrust rating down/up :-/-
Materials Seal Information
Bowl : Cast Iron A48 CL30 Arrangement : Packed Box
Impeller : Bronze Size :-
Bowl bearing : Bronze C84400 Manufacturer / Type : - / Packing
Bowl shaft : 416SS A582 Gr 416 Material code (Man'f/API) :-/-
Bowl wear ring : None supplied Gland material :-
Impeller wear ring : None supplied Auxiliary seal device :-
Column : Steel A53 Type E GrB Seal flush plan :-
Lineshaft : 416 stainless steel Seal flush construction :-
Bearing retainer Paint and Package
Lineshaft bearing : Bronze C84400 Pump paint :-
Lineshaft sleeve :- Support plate paint :-
Discharge head : Carbon Steel Shipment type :-
Support plate : None supplied Additional information
Weights (Approx.) Pit / sump depth :-
Complete pump :- Pump length : 10.28 ft
Mounting plate :- mounting surface to bell/strainer bottom
Driver (net) :- Available well diameter :-
Testing Max dia below mtg surface : 14.00 in
Hydrostatic test : None
Performance test :-
NPSH test :-
Notes
-
Copyright © 2016 Flowserve. All rights reserved. Affinity v2.16.0
Full Page GA Drawing
-
Customer : Eduin Moreno Pump size & type : 12EHM Drawing number :-
Item number : Booster Inyección Castilla II Pump speed / Stages : 1785 rpm / 9 Date : February 27, 2020
Service : Agua Flow / Head : 1400.0 USgpm / 520.60 ft Certified by / Date : :-
Customer PO # :- Driver power / Frame : 250 hp / 186 kW / - Seal type : Packing
Flowserve reference : 2404455269 Volts / Phase / Hz : 480 / - / 60 Hz Seal flush plan :-
Copyright © 2016 Flowserve. All rights reserved. Affinity v2.16.0
Customer : Eduin Moreno Capacity : 1400.0 USgpm
Item number : Booster Inyección Castilla II Head : 520.60 ft
Service : Agua Density / Specific gravity : - / 1.000
Flowserve reference : 2404455269 Pump speed : 1785 rpm
Pump size & type / Stages : 12EHM /9 Ns / Nss : 2964 / 9250 (US units)
Based on curve no. : EC-2657
Impeller diameter : 9.25 in
Date : February 27, 2020
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Bowl performance shown below is corrected for materials, viscosity and construction.
Bowl head of 522.1 ft corresponds with 520.6 ft head at discharge flange adjusted for elevation and friction losses.
Copyright © 2016 Flowserve. All rights reserved. Affinity v2.16.0
