7/8/2019 A Regular ASME Design Checklist - deconeq Engineering Group
HOME ABOUT US SERVICES CAREERS
A REGULAR ASME DESIGN CHECKLIST
Home › Code Calculation › A Regular ASME Design Checklist
Here a short checklist is provided which is a minimum to a design according to the ASME Boiler and
Pressure Vessel Code Section VIII-1. For more detailed process, or speci c design condition, contact posts
deconeq Engineering Group design team or simply send an email to [email protected] .
Dimple Jacket Pressure Drop M
2019
WRC 107 vs WRC 537 Novembe
2018
CRN fee April 19, 2018
Unlisted Materials March 20, 20
How to Find CRN Number for a
September 24, 2017
1- De ning design conditions:
These information usually appear on the design documents and/or General Arrangement Drawings.
Search
1. Document/Drawing No. and Revision
2. ASME Code Edition and Addenda
Search …
3. Code Cases
4. Units: SI/U.S. Customary
5. Design- operational data
6. MDMT (Minimum Design Metal Temperature)
7. Materials of construction
Subscribe to Blog via Em
8. Main dimensions of the equipment or component
9. Applicable Loads
Email Address
10. Check permissible S- value listed in applicable Code Section
11. Services Restrictions
Subscribe
12. Nameplate data, location of nameplate
13. Check if National Board registration is required
14. Check if CRN- Registration is required for application or installation in Canada
15. Identi cation of joints
16. Assignment WPS to joints and preparing the welding methids
2. Test Pressure (Minimum):
1. Hydrostatic Test: which is de ned as 1.3*MAWP*LSR
2. Pneumatic Test: wgich is de ned as 1.1* MAWP*(S[T test/ S[T design])
3. Type of Weld Joint:
1. RT Examination Selection, location of “Spot”
2. NDE(PT/MT) on Corner Joints Joggle Joint
3. Hubbed anges from rolled plate
https://deconeq.com/a-regular-asme-design-checklist/ 1/3
7/8/2019 A Regular ASME Design Checklist - deconeq Engineering Group
4. Corrosion Allowance:
5.Tolerances:
1. Wall thickness, plate and pipe
2. Misalignment
3. Tapered transitions
4. Staggered longitudinal joints
5. Out-of-roundness for internal pressure
6. Out-of-roundness for ext. pressure calculated + data transfered to prod./QC
6. Inspection Openings:
7. Check whether design calculations have been made for all presure bearing parts:
1. Shell, conical reducer section(conical reducer section shall also meet the requirements of Appendix 1-5
and/or 1-8)
2. Dished heads, conical heads Compensation of openings(large openings see also App. 1-7 or 1-10)
3. Flanges (App. 2 or ASME B16.5)
4. Covers, at heads
5. Bolts
6. Tube sheets: applicability and use od UHX(otherwise, see also TEMA)
7. Expansion joint (see also EJMA)
8. Nozzle attachment welds(allowable stresses in welds)
9. External pressure
10. Jacketed vessel Appendix 9
11. loadings e.g. vessel supports
12. shell sections and heads extreme bre elongation
8. Minimum wall thickness:
1. Shell
2. Dished head
3. Nozzle
4. Remaining wall thickness underneath tapped holes
9. Minimum weld dimensions:
1. Flange attachment to the nozzle
2. Nozzle attachment to the shell or head
3. Attachment of at heads + covers
10. Pressure rating of standard parts:
Based on material and temperature (ASME Products) Calculated at straight seamless pipe
11. Heat treatment
12. Impact Test Requirements
(cryogenic vessels) Exemptions documented for all mat.
13. Exposed inside edges chamfered or rounded
14. Telltale holes in nozzle reinf. plates
15. Split/ segmental reinf. plates
16. Referenced standards
17. Proof Test
18. Partial Data Report
Share
https://deconeq.com/a-regular-asme-design-checklist/ 2/3
7/8/2019 A Regular ASME Design Checklist - deconeq Engineering Group
CONTACT INFO READ ABOUT RECENT POSTS
2302 - 2900 HWY 7 Code Calculation Dimple Jacket Pressure Drop
Vaughan, Ontario L4K 0G3 CRN Registration WRC 107 vs WRC 537
1-437-886-6120
Design Engineering CRN fee
[email protected] Unlisted Materials
Mon - Sat: 8:00 am to 5: pm
How to Find CRN Number for a
Product
@ Copyright 2016 deconeq deconeq | deconeq Eng
https://deconeq.com/a-regular-asme-design-checklist/ 3/3
