Installation Instructions

ArmorBlock 2-Port EtherNet/IP Module

Catalog Numbers 1732E-IB16M12R, 1732E-OB16M12R,
1732E-IB16M12DR, 1732E-OB16M12DR, 1732E-16CFGM12R,
1732E-IB16M12SOEDR, 1732E-8X8M12DR

Table of Contents
Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

Overview 4

Catalog Number Explanation 6

Install the Module 6

Set the Network Address 6

Mount the Module 7

Product Dimensions 8

Connect the I/O, Network and Auxiliary Cables to the Module 9

Configure the Module 12

Interpret LED Indicators 13

Specifications 15
2 ArmorBlock 2-Port EtherNet/IP Module

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls
(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at
http://www.rockwellautomation.com/literature/) describes some important differences between
solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also
because of the wide variety of uses for solid-state equipment, all persons responsible for applying this
equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular installation, Rockwell Automation, Inc.
cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,
property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you
identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or
motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or
motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the
product.

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 3

Environment and Enclosure

ATTENTION: This equipment is intended for use in overvoltage Category II

applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft)
without derating.
This equipment is considered Group 1, Class A industrial equipment according
to IEC/CISPR 11. Without appropriate precautions, there may be difficulties
with electromagnetic compatibility in residential and other environments due to
conducted and radiated disturbances.
This equipment is supplied as enclosed equipment. It should not require
additional system enclosure when used in locations consistent with the
equipment Enclosure Type Ratings. Subsequent sections of this publication
may contain more information regarding specific enclosure type ratings,
beyond what this product provides, that are required to comply with certain
product safety certifications.
In addition to this publication, see:
• Industrial Automation Wiring and Grounding Guidelines, Rockwell
Automation publication 1770-4.1, for additional installation requirements.
• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the
degrees of protection provided by different types of enclosure.

Preventing Electrostatic Discharge

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines
when you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.

Publication 1732E-IN004D-EN-E - March 2017

4 ArmorBlock 2-Port EtherNet/IP Module

Additional Resources
Resource Description

Pinout Guide for 1732 ArmorBlock 2 Port Detailed description of how to wire your module.
Ethernet Block, publication 1732E-WD001

1732E EtherNet/IP ArmorBlock supporting Detailed description of how to install, configure and use
Sequence of Events, your 1732E-IB16M12SOEDR module.
publication 1732E-UM002

Integrated Architecture and CIP Sync Detailed explanation on how to set up and use
Configuration, publication IA-AT003 ArmorBlock modules in a CIP Sync application.

Industrial Automation Wiring and Grounding More information on proper wiring and grounding
Guidelines, publication 1770-4.1 techniques.

If you would like a manual, you can:

• download a free electronic version from the internet:
http://www.rockwellautomation.com/literature/
• purchase a printed manual by contacting your local Allen-Bradley distributor or
Rockwell Automation representative

Overview
The EtherNet/IP ArmorBlock is a 24V DC I/O module that communicates via
EtherNet/IP. The sealed IP65, IP67 and IP69K housing of these modules requires no
enclosure. I/O connectors are sealed M12 style.
EtherNet/IP networks use advanced network technology, for example,
producer/consumer communication, to increase network functionality and throughput.

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 5

Module Identification

Status LEDs Functional Earth(1)

EtherNet/IP D-Code LINK 1 LINK 2 EtherNet/IP D-Code

M12 connector M12 connector

M12 I/O connectors M12 I/O connectors

Auxiliary power Node address

switches
Protective Earth(2)
44945

(1) Protective Earth is provided for the grounding of field devices and is internally connected to each Pin 5 of the M12 I/O
connectors. See I/O Connectors on page 9.

(2) Functional Earth grounds the I/O block’s EtherNet/IP communication circuitry which is designed to mitigate the effect of
noise on the network. See EtherNet/IP Connector on page 10.

Publication 1732E-IN004D-EN-E - March 2017

6 ArmorBlock 2-Port EtherNet/IP Module

Catalog Number Explanation

Refer to the table for a description of the module catalog numbers.
Catalog Number Description Network Auxiliary
Connector Power
1732E-IB16M12R 16 Channel 24V DC Digital Input Dual-Port Dual D-code Single
EtherNet Module M12 4-pin mini
1732E-OB16M12R 16 Channel 24V DC Digital Output Dual-Port
EtherNet Module
1732E-16CFGM12R 16 Channel 24V DC Configurable Digital I/O
Dual-Port EtherNet Module
1732E-IB16M12DR Diagnostic 16 Channel 24V DC Digital Input
Dual-Port EtherNet Module
732E-OB16M12DR Diagnostic 16 Channel 24V DC Digital Output
Dual-Port EtherNet Module
1732E-8X8M12DR Diagnostic 8-Input/8-Output 24V DC Digital I/O
Dual-Port EtherNet Module
1732E-IB16M12SOEDR Diagnostic Sequence of Events 16 Channel 24V
DC Digital Input Dual-Port EtherNet Module

Install the Module

To install the module:
• Set the network address
• Mount the module
• Connect the I/O, Network and Auxiliary cables to the module.

Set the Network Address

The I/O block ships with the rotary switches set to 999 and DHCP enabled.
To change the network address, you can do one of the following:
• adjust the switch on the front of the module.
• use a Dynamic Host Configuration Protocol (DHCP) server, such as Rockwell
Automation BootP/DHCP.
• retrieve the IP address from nonvolatile memory.
The I/O block reads the switches first to determine if the switches are set to a valid
number. To set the network address:
1. Rotate the three (3) switches on the front of the module using a small
blade screwdriver.

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 7

2. Line up the small notch on the switch with the number setting you wish to use.
Valid settings range from 001…254.
3. Cycle power.
Set Network Address

Example shows default

node address set at 163.

44233

When the switches are set to a valid number, the I/O block’s IP address is 192.168.1.xxx
(where xxx represents the number set on the switches). The I/O block’s subnet mask is
255.255.255.0 and the gateway address is set to 0.0.0.0. When the I/O block uses the
network address set on the switches, the I/O block does not have a host name assigned to it
or use any Domain Name Server.
If the switches are set to an invalid number (for example, 000 or a value greater than 254
excluding 888), the I/O block checks to see if DHCP is enabled. If DHCP is enabled, the
I/O block asks for an address from a DHCP server. The DHCP server also assigns other
Transport Control Protocol (TCP) parameters.
If DHCP is not enabled, the I/O block uses the IP address (along with other TCP
configurable parameters) stored in nonvolatile memory.

Mount the Module

Two sets of mounting holes are used to mount the module directly to a panel or machine.
Mounting holes accommodate #8 (M4) pan head screws. The torque specification is
1.13 Nm (10 in-lb).

Publication 1732E-IN004D-EN-E - March 2017

8 ArmorBlock 2-Port EtherNet/IP Module

Product Dimensions
Refer to the mounting dimensions illustration to help you mount the module.
Module Dimensions
43.25 mm
65 mm
(1.70 in.)
(2.56 in.)
26.5 mm
(1.04 in.)

LINK 1 LINK 2

179 mm
(7.05 in.)
169 mm
(6.65 in.)

44946

Front view Side view

Mount the Module in High Vibration Areas

If you mount the module in an area that is subject to shock or vibration, we recommend
you use a flat and a lock washer to mount the module. Mount the flat and the lock washer
as shown in the mounting illustration. Torque the mounting screws to 1.13 Nm (10 in-lb).

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 9

High Vibration Area Mounting

Lock washer

Flat washer 44766

Connect the I/O, Network and Auxiliary Cables to the Module

The ArmorBlock EtherNet/IP family has 5-pin micro-style connectors. We provide caps
to cover the unused connectors on your module. Connect the quick-disconnect cord sets
you selected for your module to the appropriate ports.

I/O Connectors

Refer to the pinout diagrams for the I/O connectors

Micro-style 5-Pin Input Female Connector
(View into connector)
1 2 Pin 1 Sensor source voltage
Pin 2 Input B
5 Pin 3 Return
Pin 4 Input A
4 3
Pin 5 PE
44807

Micro-style 5-Pin Output Female Connector

(View into connector)

1 2 Pin 1 Not used
Pin 2 Output B
5
Pin 3 Return
4 3 Pin 4 Output A
44807 Pin 5 PE

Publication 1732E-IN004D-EN-E - March 2017

10 ArmorBlock 2-Port EtherNet/IP Module

Self-configuring Connector

(View into connector)

1 2 Pin 1 Sensor source voltage
Pin 2 Input or output B
5
Pin 3 Return
4 3 Pin 4 Input or output A
44807 Pin 5 PE

I/O Self-configure Circuitry

Turn output on Output

circuit
From PLC Sensor or
Output scan list actuator
Input scan list
To PLC
Input Connector pin
Input is on circuit
43601
(or output is on)

EtherNet/IP Connector

D-Code Micro Network Female Connector

(View into connector)
4 Pin 1 M12_Tx+
Pin 2 M12_Rx+
3 1 Pin 3 M12_Tx-
Pin 4 M12_Rx-
2 Pin 5 Connector shell shield FE
5
44808

ATTENTION: Make sure all connectors and caps are securely tightened to
properly seal the connections against leaks and maintain IP enclosure
requirements.

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 11

IMPORTANT Use the 1585D–M4DC–H: Polyamide small body unshielded or the 1585D–
M4DC–SH: Zinc die-cast large body shielded mating connectors for the
D-Code M12 female network connector.

IMPORTANT Use two twisted pair CAT5E UTP or STP cables.

D-Code Wire color Signal 8-way modular
M12 Pin RJ45 pin
1 White-Orange TX+ 1
2 White-Green RX+ 3
3 Orange TX- 2
4 Green RX- 6

The 1732E-16CFGM12R self-configuring module contains both input and output

functionality.
• If an I/O point is to be an output, dedicate that point as an output with a wired
load and energize it through a control program.
• Energized outputs show an associated active input that can be used as a feedback
mechanism to make certain that the output is on.
• If an I/O point is to be an input, wire the input device as normal and leave the
associated output de-energized at all times.

Auxiliary Power Connector

Attach the mini-style 4-pin connector to the mini-style 4-pin receptacle as shown below.
Mini-style 4-Pin Input Male Receptacle
(View into receptacle)
Pin 1 Output power+
4 2
Pin 2 Sensor/MDL power+
Pin 3 Sensor/MDL power-
3 1 Pin 4 Output power-

44809
Auxiliary Power is based on a 4-pin connector system and is used to provide 24V DC
power to I/O modules and other devices. Running separate power to these devices is most
typically used for I/O devices with output connections to prevent power supply
interruption due to switching of outputs. However, some devices require separate auxiliary
power to power them regardless of the presence of outputs.

Publication 1732E-IN004D-EN-E - March 2017

12 ArmorBlock 2-Port EtherNet/IP Module

Depending on the devices used, it may be possible to provide power through only one pair
of the four available pins, and in this case the other available pair may be used for single
channel E-stop through the use of special E-stop drop or power T-ports and shorting
plugs. Allen-Bradley E-stop T-ports and shorting plugs are red in color for
easy identification.

ATTENTION: To comply with the CE Low Voltage Directive (LVD), this

equipment and all connected I/O must be powered from a source compliant
with the following:
Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).

ATTENTION: To comply with UL restrictions, this equipment must be powered

from a source compliant with the following: Limited Voltage/Current.

Configure the Module

Refer to the illustration for configuration operations.
Configure Operations

EtherNet/IP D-Code LINK 1 LINK 2

EtherNet/IP D-Code
M12 connector M12 connector

Eight M12 I/O

connectors

Network address
Auxiliary power
switches
44945

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 13

Refer to On-Machine Connectivity Catalog, publication M117-CA001, for Rockwell

Automation cable and cord set offerings or use the configuration tools available at
www.rockwellautomation.com/en/e-tools/.

Interpret LED Indicators

This module has the following indicators:
• Network, Module, and Link status indicators for EtherNet/IP
• Auxiliary Power indicator
• Individual I/O status indicators for inputs and outputs

Link Link
status status
indicator indicator
LINK 1 LINK 2

Module Module
status status
indicator indicator

I/O status I/O status

indicator indicator

Auxiliary power
indicator

44945

Publication 1732E-IN004D-EN-E - March 2017

14 ArmorBlock 2-Port EtherNet/IP Module

Indicator Status for Modules

Indicator Status Description
Module status Off No power applied to device.
Flashing red/green The module is performing POST (Power-On Self Test),
which completes within 30 s.
Green Device operating normally.
Flashing red Recoverable fault.
Red Unrecoverable fault – may require device
replacement.
Network status Off The device is not initialized or the module does not
have an IP address.
Flashing green The device has no CIP connections.
The device has an IP address, but no CIP connections
are established.
Green The device is online, has an IP address, and CIP
connections are established.
Flashing red One or more connections have timed out.
Red The module has detected that its IP address is already
in use.
Flashing red/green The module is performing a powerup self-test.
Network link status Off No link established.
Green Link established on indicated port at 100 Mbps.
Flashing green Link activity present on indicated port at 100 Mbps.
Yellow Link established on indicated port at 10 Mbps.
Flashing yellow Link activity present on indicated port at 10 Mbps.
Auxiliary status Off No auxiliary power to device or input not valid.
Green Auxiliary power applied to device.
Digital output status(1) Off Output not energized.
Yellow Output energized.
Red Output shorted.
Flashing red Output open load.
Digital input status(1) Off No valid input.
Yellow Valid input.
Red Sensor source voltage shorted.
Flashing red Sensor source open wire.
(1)
Only diagnostic modules 1732E-*DR have red I/O status indicators.

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 15

Specifications
1732E ArmorBlock 2-Port EtherNet Module Input – 1732E-8X8M12DR,
1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR,
1732E-16CFGM12R
Attribute Value
Number of inputs 8 – 1732E-8X8M12DR
16 – all other modules
Input type Sink, 24V DC
Voltage, off-state input, max 5V DC
Voltage, on-state input, max 30V DC
Voltage, on-state input, nom 24V DC
Voltage, on-state input, min 11V DC
Current, off-state input, max 1.5 mA @ 5V DC
Current, on-state input, max 5 mA @ 30V DC
Voltage, sensor source, max 30V DC
Voltage, sensor source, min 10V DC
Input delay time
ON to OFF 0…16000 μs
OFF to ON
Isolation voltage 50V (continuous), Basic Insulation Type, Inputs and Sensor Power
to Network.
No isolation between individual Inputs or between
Network channels.
Type tested at 707V DC for 60 s.

1732E ArmorBlock 2-Port EtherNet Module Output – 1732E-8X8M12DR,

1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R
Attribute Value
Number of outputs 8 – 1732E-8X8M12DR
16 – all other modules
Output type Source, 24V DC
Voltage drop, on-state output, max 0.5V DC
Voltage off-peak blocking, min 30V DC
Voltage, on-state output, max 30V DC
Voltage, on-state output, min 11V DC

Publication 1732E-IN004D-EN-E - March 2017

16 ArmorBlock 2-Port EtherNet/IP Module

1732E ArmorBlock 2-Port EtherNet Module Output – 1732E-8X8M12DR,

1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R
Attribute Value
Voltage, on-state output, nom 24V DC
Current on-state output, max 2.0 A – 1732E-OB16M12R
0.5 A – all other modules
Current per module, max 4.0 A – 1732E-8X8M12DR
8.0 A – all other modules
Leakage current, off-state output, max 50 μA – 1732E-OB16M12R, 1732E-16CFGM12R
500 μA – all other modules
Surge current per output, min 4.8 A for 10 ms, repeatable every 2 s – 1732E-OB16M12R
1.2 A for 10 ms, repeatable every 2 s – all other modules
Pilot duty rating DC-14
Isolation voltage 50V (continuous), Basic Insulation Type, Outputs and Output
Power to Network.
No isolation between individual Outputs or between Outputs
and Output power or between Network channels.
Type tested at 707V DC for 60 s.

General Specifications
Attribute Value
Voltage, auxiliary power, max 30V DC
Voltage, auxiliary power, min 12V DC
Current, Ethernet system power, max (pins 0.4 A – 1732E-OB16M12R, 1732E-OB16M12DR
2, 3 sensor source/module power) 0.8 A – 1732E-8X8M12DR
1.2 A – 1732E-IB16M12R, 1732E-IB16M12DR,
1732E-IB16M12SOEDR,1732E-16CFGM12R
Current, auxiliary power, max per output 4 A – 1732E-8X8M12DR
module (pins 2, 3 sensor source/module 8 A – all other modules
power plus pins 1, 4 for output loads)
Current, sensor source, per input, max 50 mA
Current, sensor source, per connector, max 100 mA
Communication rate EtherNet/IP
10/100 Mbps
Full or half-duplex
100 meter per segment

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 17

General Specifications
Attribute Value
Isolation voltage 50V (continuous), Basic Insulation Type, Inputs and Sensor
Power to Network
No isolation between individual Inputs or between
Network channels
Type tested at 707V DC for 60 s
Status indicators Module status - red/green
Network status - red/green
Link status - green/yellow
Auxiliary power - green
I/O LED - yellow
I/O LED - yellow/red – 1732E-*DR modules only
Dimensions (HxWxD), approx. 179 x 65 x 43.25 mm
(7.05 x 2.56 x 1.70 in.)
Weight, approx. 0.34 kg (0.75 lb)
Enclosure type rating Meets IP65/66/67/69K (when marked), and Type 4X with
receptacle dust caps or cable termination.
Wiring category(1) 1 – on signal ports
1 – on power ports
1 – on communications port

(1) Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring and
Grounding Guidelines, publication 1770-4.1.

Environmental Specifications
Attribute Value
Temperature, IEC 60068-2-1 (Test Ad, Operating Cold),
operating IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20…60 °C (-4…140 °F)
Temperature, 60 °C (140 °F)
surrounding, max.
Temperature, storage IEC 60068-2-1 (Test Ab, Unpackaged Non-operating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Non-operating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Non-operating Thermal Shock):
-40…85 °C (-40…185 °F)
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5…95% noncondensing
Vibration IEC 60068-2-6 (Test Fc, Operating):
5 g @ 10... 500 Hz
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
30 g

Publication 1732E-IN004D-EN-E - March 2017

18 ArmorBlock 2-Port EtherNet/IP Module

Environmental Specifications
Attribute Value
Shock, non-operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
50 g
Emissions CISPR 11
Group 1, Class A
ESD immunity IEC 61000-4-2:
6 kV contact discharges
8 kV air discharges
Radiated RF immunity IEC 61000-4-3:
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
10V/m with 200 Hz 50% Pulse 100% AM @ 900 Mhz
10V/m with 200 Hz 50% Pulse 100% AM @ 1890 Mhz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
EFT/B immunity IEC 61000-4-4:
±4 kV @ 5 kHz on power ports
±3 kV @ 5 kHz on signal ports
±3 kV @ 5 kHz on communications ports
Surge transient IEC 61000-4-5:
immunity ±1 kV line-line(DM) and ±2 kV line-earth(CM) on power ports
±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports
±2 kV line-earth(CM) on communications ports
Conducted RF IEC 61000-4-6:
immunity 10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz

Publication 1732E-IN004D-EN-E - March 2017

 ArmorBlock 2-Port EtherNet/IP Module 19

Certifications
Certification (when Value
product is marked)(1)

c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.

See UL File E322657.

CE European Union 2014/30/EU EMC Directive, compliant with:

EN 61326-1; Meas./Control/Lab., Industrial Requirements
EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)

RCM Australian Radiocommunications Act, compliant with:

AS/NZS CISPR 11; Industrial Emissions

EtherNet/IP ODVA conformance tested to EtherNet/IP specifications.

KC Korean Registration of Broadcasting and Communications Equipment,

compliant with:
Article 58-2 of Radio Waves Act, Clause 3

(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for Declaration of

Conformity, Certificates, and other certification details.

Publication 1732E-IN004D-EN-E - March 2017

Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its products. At
http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs,
technical and application notes, sample code and links to software service packs, and a MySupport feature
that you can customize to make the best use of these tools.

For an additional level of technical phone support for installation, configuration and troubleshooting, we
offer TechConnect support programs. For more information, contact your local distributor or Rockwell
Automation representative, or visit http://www.rockwellautomation.com/support/.

Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the information that's
contained in this manual. You can also contact a special Customer Support number for initial help in getting
your product up and running.

United States or Canada 1.440.646.3434

Outside United States or Use the Worldwide Locator at
Canada http://www.rockwellautomation.com/support/americas/phone_en.html, or
contact your local Rockwell Automation representative.

New Product Satisfaction Return

Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from
the manufacturing facility. However, if your product is not functioning and needs to be returned, follow
these procedures.

United States Contact your distributor. You must provide a Customer Support case number
(call the phone number above to obtain one) to your distributor to complete
the return process.
Outside United States Please contact your local Rockwell Automation representative for the return
procedure.

Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to
improve this document, complete this form, publication RA-DU002, available at
http://www.rockwellautomation.com/literature/.

Allen-Bradley, Rockwell Automation, ArmorBlock, and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Publication 1732E-IN004D-EN-E - March 2017

Supersedes Publication 1732E-IN004C-EN-E May 2012 Copyright © 2017 Rockwell Automation, Inc. All rights reserved.