UncUt antiextrUsion ring for metric o-ring
AM
MATERIAL
Type Designation Hardness
Thermoplastic SEALITE 55 55 °ShD
polyester resin
FIELD OF APPLICATION
Pressure See table below
0 m/s 2 4 6 8 10 12 14
Speed
≤ 0.8 m/s
Temperature -200 -150 -100 -50 0 °C 50 100 150
–40°C ÷ +140°C
(only for SEALITE
element)
Hydraulic oils (mineral oil based)
Fluids For other fluids contact our technical department
MAX. PRESSURE [bar]
Gap NBR 70 NBR 90 AM
[mm] [bar] [bar] [bar]
0,05 190 330 500
0,10 130 270 400
The function of ring type Aston Seals AM is to the manufacturing of antiextrusion rings, that 0,15 110 230 350
avoid the extrusion and damage of the O-Ring ensures an extra measure of performance and 0,20 100 210 300
0,25 90 190 270
that normally occurs in the presence of large service life in application where properties
0,30 80 170 240
gaps or high pressure. such as abrasion resistance and tear strength 0,35 75 160 220
If pressure arises on only one side of the O- are critical.
Ring, it will suffice to fit one antiextrusion ring • Very high resistance against extrusion NB: for the Gap calculation, it is necessary to consider the elastic
on the unexposed side. Two backup rings are deformation of metal elements under pressure loads.
• Uncut piece to avoid O-Ring damage
necessary if the pressure rises on both sides. SURFACE ROUGHNESS
• Low cost solution
The AM ring hasn’t a cut or spiral shape
• Extended service life of sealing components
AM
(typical of PTFE backup rings) that could help Dynamic surface Ra ≤ 0.3 µm Rt ≤ 2.5 µm
• Excellent wear-resistance Static surface Ra ≤ 1.6 µm Rt ≤ 6.3 µm
damage the O-Ring especially in the presence
of high pressure. • No close tolerances are necessary Before assembly good cleanliness and lubrication are recommended.
Thanks to its elasticity, it can be installed • Easy installation without expensive auxiliaries The above data are maximum values, they may be maintained for short
periods and can not be used at the same time simultaneously.
very easily in a short time and without any • Good temperature resistance
auxiliaries. • Easy installation without expensive auxiliaries
The material used is a medium modulus
thermoplastic polyester resin, mainly used in
Uncut antiextrusion ring for metric O-Ring
AM
Part. O-Ring d f7 D H9 h L1 +0.2 L2 +0.2 Part. O-Ring d f7 D H9 h L1 +0.2 L2 +0.2 Part. O-Ring d f7 D H9 h L1 +0.2 L2 +0.2
AM 3.8 6.5 1 4.1 x 1.6 3.8 6.5 1.0 3.1 4.1 AM 55 60 1.3 54.5 x 3 55 60 1.3 5.3 6.6 AM 80 87.6 1.75 80 x 4.5 80 87.6 1.75 7.5 9.2
AM 6 10.5 0.8 5.23 x 2.62 6 10.5 0.8 4.4 5.3 AM 55 65 1.7 54.2 x 5.7 55 65 1.7 9.5 11.5 AM 80 90 1.7 79.2 x 5.7 80 90 1.7 9.5 11.5
AM 10 14 1.3 9.3 x 2.4 10 14 1.3 4.5 5.8 AM 56.5 61 1.4 55.25 x 2.62 56.5 61 1.4 5.0 6.4 AM 83 90 1.5 83 x 4 83 90 1.5 6.8 8.3
AM 12 16 1.3 11.3 x 2.4 12 16 1.3 4.5 5.8 AM 58 63 1.3 57.0 x 3 58 63 1.3 5.3 6.6 AM 84 90 1.4 82.14 x 3.53 84 90 1.4 6.0 7.5
AM 16 20 1.3 15.3 x 2.4 16 20 1.3 4.5 5.8 AM 60 65 1.3 59.5 x 3 60 65 1.3 5.3 6.6 AM 85 90 1.3 84.5 x 3 85 90 1.3 5.3 6.6
AM 17 21 1.3 16.3 x 2.4 17 21 1.3 4.5 5.8 AM 60 67 1.5 59 x 4 60 67 1.5 6.9 8.4 AM 85 95 1.7 84.1 x 5.7 85 95 1.7 9.5 11.5
AM 20 25 1.3 19.2 x 3 20 25 1.3 5.3 6.6 AM 60 70 1.7 59.2 x 5.7 60 70 1.7 9.5 11.5 AM 89.4 100 2.5 88 x 6 89.4 100 2.5 10.7 13.2
AM 25 30 1.3 24.2 x 3 25 30 1.3 5.3 6.6 AM 64 70 1.4 63.5 x 3.53 64 70 1.4 6.0 7.5 AM 90 95 1.3 89.5 x 3 90 95 1.3 5.3 6.6
AM 25 32 1.3 24 x 4 25 32 1.3 6.7 8.2 AM 65 70 1.3 64.5 x 3 65 70 1.3 5.3 6.6 AM 90 100 1.7 89.1 x 5.7 90 100 1.7 9.5 11.5
AM 27 32 1.3 26.2 x 3 27 32 1.3 5.3 6.6 AM 65 75 1.7 64.2 x 5.7 65 75 1.7 9.5 11.5 AM 93.5 100 1.4 91.67x3.53 93.5 100 1.4 6.0 7.4
AM 29.3 35 1.4 28.17 x 3.53 29.3 35 1.4 6.0 7.5 AM 66 71 1.5 64.5 x 3 66 71 1.5 5.5 7.0 AM 94.5 101 1.5 94.84 x 3.53 94.5 101 1.5 6.1 7.6
AM 30 35 1.3 29.2 x 3 30 35 1.3 5.3 6.6 AM 66.4 72 1.4 65.09 x 3.53 66.4 72 1.4 6.0 7.4 AM 95 100 1.3 94.5 x 3 95 100 1.3 5.3 6.6
AM 33 38 1.3 32.2 x 3 33 38 1.3 5.3 6.6 AM 69 75 1.5 68.26x3.53 69 75 1.5 6.1 7.6 AM 95 105 1.7 94.1 x 5.7 95 105 1.7 9.5 11.5
AM 35 40 1.3 34.2 x 3 35 40 1.3 5.3 6.6 AM 70 75 1.3 69.5 x 3 70 75 1.3 5.3 6.6 AM 100 105 1.3 99.5 x 3 100 105 1.3 5.3 6.6
AM 36 41 1.75 34.5 x 3 36 41 1.75 5.75 7.5 AM 70 77 1.5 69 x 4 70 77 1.5 6.9 8.4 AM 100 110 1.7 99.1 x 5.7 100 110 1.7 9.5 11.5
AM
AM 40 45 1.3 39.2 x 3 40 45 1.3 5.3 6.6 AM 70 80 1.7 69.2 x 5.7 70 80 1.7 9.5 11.5 AM 103.5 110 1.5 102 x 4 103.5 110 1.5 6.7 8.2
AM 42.5 50 2 42 x 4.5 42.5 50 2.0 7.8 9.8 AM 74 80 1.5 72.62 x 3.53 74 80 1.5 6.1 7.6 AM 105 110 1.3 104.5 x 3 105 110 1.3 5.3 6.6
AM 45 50 1.3 44.2 x 3 45 50 1.3 5.3 6.6 AM 74.1 81 1.5 74 x 4 74.1 81 1.5 6.8 8.3 AM 105 115 1.7 104.1 x 5.7 105 115 1.7 9.5 11.5
AM 45 55 1.7 45.3 x 5.7 45 55 1.7 9.5 11.5 AM 74.4 80 1.4 73.03 x 3.53 74.4 80 1.4 6.0 7.4 AM 110 115 1.3 109.5 x 3 110 115 1.3 5.3 6.6
AM 50 55 1.3 49.5 x 3 50 55 1.3 5.3 6.6 AM 75 80 1.3 74.6 x 3 75 80 1.3 5.3 6.6 AM 110 120 1.7 109.1 x 5.7 110 120 1.7 9.5 11.5
AM 50 56.2 1.4 49.21 x 3.53 50 56.2 1.4 6.0 7.5 AM 75 85 1.7 74.2 x 5.7 75 85 1.7 9.5 11.5 AM 115 120 1.3 114.5 x 3 115 120 1.3 5.3 6.6
AM 50 60 1.7 49.2 x 5.7 50 60 1.7 9.5 11.5 AM 79.4 85 1.3 78.97 x 3.53 79.4 85 1.3 6.0 7.5 AM 115 125 1.7 114.3 x 5.7 115 125 1.7 9.5 11.5
AM 53 63 1.7 52.3 x 5.7 53 63 1.7 9.5 11.5 AM 80 85 1.3 79.5 x 3 80 85 1.3 5.3 6.6 AM 116.3 125 1.7 113.67 x 5.34 116.3 125 1.7 9.0 10.5
AM 54 59 1.4 53.1 x 3 54 59 1.4 5.4 6.8 AM 80 87 1.5 79 x 4 80 87 1.5 6.9 8.4 AM 119 126 1.5 118 x 4 119 126 1.5 6.9 8.4
Uncut antiextrusion ring for metric O-Ring
AM
Part. O-Ring d f7 D H9 h L1 +0.2 L2 +0.2
AM 120 125 1.3 119.5 x 3 120 125 1.3 5.3 6.6
AM 120 130 1.7 119.3 x 5.7 120 130 1.7 9.5 11.5
AM 125 130 1.3 124.5 x 3 125 130 1.3 5.3 6.6
AM 125 135 1.7 124.3 x 5.7 125 135 1.7 9.5 11.5
AM 130 140 1.7 129.3 x 5.7 130 140 1.7 9.5 11.5
AM 135 145 1.7 134.3 x 5.7 135 145 1.7 9.5 11.5
AM 140 150 1.7 139.3 x 5.7 140 150 1.7 9.5 11.5
AM 142 151 1.8 140 x 5.3 142 151 1.8 9.0 10.8
AM 145 155 1.7 144.3 x 5.7 145 155 1.7 9.5 11.5
AM 150 160 1.7 149.3 x 5.7 150 160 1.7 9.5 11.5
AM 152 161 1.8 150 x 5.3 152 161 1.8 9.0 10.8
AM 154 166 3 155.6 x 6.99 154 166 3.0 12.5 15.5
AM
