LB064V02-A1

Liquid Crystal Display

Product Specification

SPECIFICATION
FOR
APPROVAL

(●) Preliminary Specification

( ) Final Specification

Title 6.4” VGA TFT LCD

BUYER SUPPLIER LG.Philips LCD CO., Ltd.

MODEL *MODEL LB064V02

SUFFIX A1

*When you obtain standard approval,

please use the above model name without suffix

SIGNATURE DATE APPROVED BY DATE

C. S. Kyoung G.Manager
/
REVIEWED BY

/ H.J. Kim Manager

PREPARED BY

/ Y. I. Bang
Research Engineer
J. H. Kim
Assistant Research Engineer

Please return 1 copy for your confirmation with Product Engineering Dept.
your signature and comments. LG. Philips LCD Co., Ltd

Ver1. 2 MAR. 19, 2003 1 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

NO. ITEM Page

- COVER 1
- CONTENTS 2
- RECORD OF REVISIONS 3
1 GENERAL DESCRIPTION 4
2 ABSOLUTE MAXIMUM RATINGS 5
3 ELECTRICAL SPECIFICATIONS 6
3-1 ELECTRICAL CHARACTREISTICS 6
3-2 INTERFACE CONNECTIONS 8
3-3 SIGNAL TIMING SPECIFICATIONS 9
3-4 SIGNAL TIMING WAVEFORMS 10
3-5 COLOR INPUT DATA REFERNECE 11
3-6 POWER SEQUENCE 12
4 OPTICAL SPECIFICATIONS 13
5 MECHANICAL CHARACTERISTICS 17
6 RELIABILITY 21
7 INTERNATIONAL STANDARDS 22
7-1 SAFETY 22
7-2 EMC 22
8 PACKING 23
8-1 DESIGNATION OF LOT MARK 23
8-2 PAKING FORM 23
9 PRECAUTIONS 24
10 IIS(Incoming Inspection Standard) 26
Total page : 27

Ver1. 2 MAR. 19, 2003 2 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

RECORDS OF REVISIONS

Revision No Revision No Page DESCRIPTION

1.0 DEC 20,2002 - ● First Draft

1.1 JAN 27,2003 6 ● Modified a electrical characteristics

- PC , VBL , Vs, fBL, Ts, PBL, Lamp Life time
1.2 MAR 19,2003 4 ● Modified a general features
- power consumption
6 ● Modified a electrical characteristics
- Icc, Pc, VBL, IBL, fBL, PBL, Lamp Life time

Ver1. 2 MAR. 19, 2003 3 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

1. General Description

The LB064V02-A1 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive type display operating in the normally white mode. This TFT-LCD has 6.4 inches diagonally
measured active display area with VGA resolution(480 vertical by 640 horizontal pixel array) Each pixel is
divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot,
thus, presenting a palette of more than 262,144 colors. The LB064V02-A1 has been designed to apply the
interface method that enables low power consumption, weight and thickness are critical factors and graphic
display are important. In combination with the vertical arrangement of the sub-pixels, the LB064V02-A1
characteristics provide an excellent flat display for office automation products such as portable Computer
and FA.

Timing Column driver circuit

TTL 6bit Control --------------
Block
CN1

Row Driver circuit

----------

TFT-LCD
Power ( 640 X 480)
3.3Vdc
Block
CN2

Backlight Ass’y

CN1: GT101-30S-HR11 or equivalent CN2: BHSR-02VS-1(JST)

General Features
Active screen size 6.4 inches (163.2mm) diagonal
Outline Dimension 145.5(H) x 111.5(V) x 6.0(D) mm(Typ.)
Pixel Pitch 0.204 mm x 0.204mm
Pixel format 640 horiz. By 480 vert. Pixels RGB stripes arrangement
Color depth 6-bit, 262,144 colors
Luminance, white 250 cd/m2(Typ. 1point)
Power Consumption 2.310 Watt (Typ.)
Weight 160g(Typ.)
Display operating mode Transmissive mode, Normally white
Surface treatments Hard coating(3H)
Anti-glare treatment of the front polarizer, HAZE(13%)

Ver1. 2 MAR. 19, 2003 4 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS

Values
Parameter symbol Units Notes
Min. Max.

Power Input Voltage VCC -0.3 4.0 Vdc At 25 ± 5°C

Operating Temperature TOP 0 50 °C 1
Storage Temperature TST -20 60 °C 1
Operating Ambient Humidity HOP 10 90 %RH 1
Storage Humidity HST 10 90 %RH 1

Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 °C Max, and no condensation of water.

90% 80%

60 60%

Wet Bulb 50
Humidity[(%)RH]

Temperature [ ]
Storage
40 40%

30
Operation
20
20%
10
0
10%

-20 0 10 20 30 40 50 60 70 80

Dry Bulb Temperature [ ]

Ver1. 2 MAR. 19, 2003 5 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics
The LB064V02-A1 requires two power inputs. One is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second input which powers the CCFL, is typically generated
by an inverter. The inverter is an external unit to the LCD.

Table 2. ELECTRICAL CHARACTERISTICS TBD

Values
Parameter Symbol Units Notes
Min. Typ. Max.
MODULE :
Power Supply Input Voltage VCC 3.0 3.3 3.6 Vdc
Power Supply Input Current ICC 136 160 184 mA 1
Power Consumption PC - 0.530 0.636 Watts 1

LAMP :
Operating Voltage VBL 325 355 380 VRMS 2
Operating Current IBL 2.0 5.0 7.0 mA
Established Starting Voltage VS 3
at 25 °C - - 1000 VRMS
at 0 °C - - 1200 VRMS
Operating Frequency f BL 40 60 80 kHz 4
Discharge Stabilization Time Ts 1 Minutes 5
Power Consumption PBL - 1.78 2.28 Watts 6
Life Time 20,000 - - Hrs 7

Note : The design of the inverter must have specification for the lamp in LCD Assembly.
The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the
characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed
so as not to produce too much leakage current from high-voltage output of the inverter.
When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of
the lamp and the inverter(no lighting, flicker, etc) never occurs. When you confirm it, the LCD Assembly
should be operated in the same condition as installed in you instrument.
1. The specified current and power consumption are under the VCC=3.3V, 25°C,fV=60Hz condition
whereas mosaic pattern is displayed and fV is the frame frequency.
2. The variance of the voltage is ± 10%.
3. The voltage above VS should be applied to the lamps for more than 1 second for start-up.
Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current.

Ver1. 2 MAR. 19, 2003 6 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

4. The output of the inverter must have symmetrical(negative and positive) voltage waveform and
symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter
which has unsymmetrical voltage and unsymmetrical current and spike wave.
Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may
cause beat on the display. Therefore lamp frequency shall be as away possible from the
horizontal synchronous frequency and from its harmonics in order to prevent interference.
5. Let’s define the brightness of the lamp after being lighted for 5 minutes as 100%.
Ts is the time required for the brightness of the center of the lamp to be not less than 95%.
6. The lamp power consumption shown above does not include loss of external inverter.
The used lamp current is the lamp typical current.
7. The life is determined as the time at which brightness of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25 ± 2°C.
8. Do not attach a conducting tape to lamp connecting wire.
If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter
has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.

Ver1. 2 MAR. 19, 2003 7 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

3-2. Interface Connections

This LCD employs two interface connections, a 30 pin connector is used for the module electronics and the
other connector is used for the integral backlight system.
The electronics interface connector is a model GT101-30S-HR11 manufactured by LG Cable.
The pin configuration for the connector is shown in the table below.
Table 3. MODULE CONNECTOR PIN CONFIGURATION
Pin Symbol Description Notes

1 GND Ground
2 VCC Power (3.3V) 1. Connector
3 VCC Power (3.3V) 1.1 LCD : GT101-30S-HR11 (LG Cable)
4 GND Ground 1.2 Mating : FI-X30M ( JAE) or equivalent
5 DCLK Data Input Clock
6 DE Data Enable Signal 2.3 Connector pin arrangement
7 VSYNC Vertical Sync Signal
8 HSYNC Horizontal Sync Signal
9 GND Ground 30 1
10 R0 Red Data 0[LSB] ---------
11 R1 Red Data 1
12 R2 Red Data 2 [ LCD Module Rear View ]
13 R3 Red Data 3
14 R4 Red Data 4
15 R5 Red Data 5[MSB]
16 GND Ground
17 G0 Green Data 0[LSB]
18 G1 Green Data 1
19 G2 Green Data 2
20 G3 Green Data 3
21 G4 Green Data 4
22 G5 Green Data 5[MSB]
23 GND Ground
24 B0 Blue Data 0[LSB]
25 B1 Blue Data 1
26 B2 Blue Data 2
27 B3 Blue Data 3
28 B4 Blue Data 4
29 B5 Blue Data 5[MSB]
30 GND Ground

The backlight interface connector is a model BHSR-02VS-1, manufactured by JST. The mating connector
part number is SM02B-BHSS-1 by JST or equivalent.
The pin configuration for the connector is shown in the table below.
Table 4. BACKLIGHT CONNECTOR PIN CONFIGURATION
Pin Symbol Description Notes
1 HV Power supply for lamp(High voltage side) 1
2 LV Power supply for lamp(Low voltage side) 1

Notes : 1. The high voltage side terminal is colored pink. The low voltage side terminal is white.

Ver1. 2 MAR. 19, 2003 8 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

3-3. Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing
should be satisfied with the following specifications for it’s proper operation.

ITEM SYMBOL MIN TYP. MAX. UNIT NOTES

Period tCLK 35 39.7 46 ns

Dclk
Frequency fclk 22 25 28 MHz

Period tHP 696 800 880

Hsync tCLK
Width tWH 24 96 144

Period tVP 486 525 - tHP

Vsync Frequency fV 55 60 65 Hz

Width tWV 2 2 - tHP

DE Horizontal Valid tHV 640 640 640 tCLK

Horizontal Back Porch tHBP 16 40 -

(Data
Enable) Horizontal Front Porch tHFP 16 24 -

Horizontal Blank - 56 160 tHP - tHV tWH + tHBP + tHFP

Vertical Valid tVV 480 480 480 tHP

Vertical Back Porch tVBP 2 33 -

Vertical Front Porch tVFP 2 10 -

Vertical Blank - 6 45 tVP - tVV tWV + tVBP + tVFP

1. Hsync Period and Hsync Width-Active should be even number times of tCLK.
If the value is odd number times of tCLK, display control signal can be asynchronous

Ver1. 2 MAR. 19, 2003 9 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

3-4. Signal Timing Waveforms

0.7Vcc
Hsync, Vsync, DE, DATA
0.3Vcc

tCLK
0.5VCC

Dclk
VALID

INVALID INVALID
DATA

DE(Data Enable)

tHP
Hsync tWH

tHBP tHV tHFP

DE(Data Enable)
tVP
tWV
Vsync
tVBP tVV tVFP

DE(Data Enable)

Ver1. 2 MAR. 19, 2003 10 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

3-5. Color Input Data Reference

The brightness of each primary color(red,green and blue) is based on the 6-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.

Table 7. COLOR DATA REFERENCE

Input Color Data

Red Green Blue
Color MSB LSB MSB LSB MSB LSB
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Green(63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Basic Blue(63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Colors Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Red(00) Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Red(02) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
Red : : : : : : : : : : : : : : : : : : :
Red(61) 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Red(62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(63) Bright 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Green(00)Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
Green(02) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
Green : : : : : : : : : : : : : : : : : : :
Green(61) 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0
Green(62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0
Green(63)Bright 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Blue(00) Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue(01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Blue(02) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
Blue : : : : : : : : : : : : : : : : : : :
Blue(61) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1
Blue(62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0
Blue(63) Bright 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Ver1. 2 MAR. 19, 2003 11 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

3-6. Power Sequence

90% 90%
Power Supply For LCD
VCC
10% 10%

0V T7
T2 T6
T1 T5

Interface Signal,
Vi Valid Data
(TTL Signal)
0V T3
T4

Power for Lamp OFF LAMP ON OFF

Values
Parameter Units
Min. Typ. Max.

T1 - - 10 ms
T2 0 - 50 ms
T3 200 - - ms
T4 200 - - ms
T5 0 - 50 ms
T6 - - 10 ms
T7 400 - - ms

Notes : 1. Please avoid floating state of interface signal at invalid period.

2. When the interface signal is invalid, be sure to pull down the power
supply for LCD VCC to 0V.
3. Lamp power must be turn on after power supply for LCD and
interface signal are valid.

Ver1. 2 MAR. 19, 2003 12 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes
in a dark environment at 25 °C. The values specified are at an approximate distance 50cm from the LCD
surface at a viewing angle of Φ and θ equal to 0 °.
FIG. 1 presents additional information concerning the measurement equipment and method.

FIG. 1 Optical Characteristic Measurement Equipment and Method

Optical Stage(x,y)

LCD Module

Field = 1 °
Prichard PR880
or equivalent

500mm

(Ta=25 °C, VCC=3.3V, fV=60Hz

Table 8. OPTICAL CHARACTERISTICS Dclk=25MHz, IBL=5mA)
Values
Parameter Symbol Units Notes
Min. Typ. Max.
Contrast Ratio CR 200 300 - 1
Surface Luminance, white LWH 210 250 - cd/m2 2
Luminance Variation δ WHITE - 1.4 1.6 3
Response Time Tr ms 4
Rise Time TrR - 15 30
Decay Time TrD - 30 50
CIE Color Coordinates
Red Rx - TBD -
Ry - TBD -
Green Gx - TBD -
Gy - TBD -
Blue Bx - TBD -
By - TBD -
White Wx - TBD -
Wy - TBD -
Viewing Angle
x axis, right(φ=0°) θr 40 45 - degree 5
x axis, left (φ=180°) θl 40 45 -
y axis, up (φ=90°) θu 10 15 -
y axis, down (φ=270°) θd 30 35 -
Gray Sclae - - - - 6

Ver1. 2 MAR. 19, 2003 13 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

Notes : 1. Contrast Ratio(CR) is defined mathematically as :

Surface Luminance with all white pixels
Contrast Ratio =
Surface Luminance with all black pixels

2. Surface luminance is the center point across the LCD surface 50cm from the surface with all
pixels displaying white. For more information see FIG 2.
When IBL=5mA, LWH=210cd/m2(Min.) 250cd/m2(Typ.)

3. The variation in surface luminance , δ WHITE is determined by measuring LON at each test
position 1 through 5, and then dividing the maximum LON of 5 points luminance by minimum LON
of 5 points luminance. For more information see FIG 2.
δ WHITE = Maximum(LON1,LON2, ….. LON5) ÷ Minimum(LON1,LON2, ….. LON5)

4. Response time is the time required for the display to transition from to black(Rise Time, TrR)
and from black to white(Decay Time, TrD). For additional information see FIG 3.

5. Viewing angle is the angle at which the contrast ratio is greater than 5. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD surface. For more information see FIG 4.

6. Gray scale specification

Luminance(%)
Gray Level
(Typ.)
L0 TBD
L7 TBD
L15 TBD
L23 TBD
L31 TBD
L39 TBD
L47 TBD
L55 TBD
L63
TBD

Ver1. 2 MAR. 19, 2003 14 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

FIG. 2 Luminance

<measuring point for luminance variation> <measuring point for surface luminance>

H H
A H 400
2

V
2 3 2
B
300 V
V
1

4 5

A : H/4 mm
B : V/4 mm Active Area
H : 130.56 mm
V : 97.92 mm
@ H,V : Active Area

FIG. 3 Response Time

The response time is defined as the following figure and shall be measured by
switching the input signal for “black” and “white”.

TrR TrD
%

100
90
Optical
Response
10 white white
0 black

Ver1. 2 MAR. 19, 2003 15 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

FIG. 4 Viewing angle

<dimension of viewing angle range>

θ = 0¡ £
φ = 90¡ £ z A
yu
(12:00)
θ

φ =180¡ £ φ = 0¡ £
xl
(9:00) (3:00) xr

TFT LCD φ =270¡ £

z' yd
MODULE (6:00)

Ver1. 2 MAR. 19, 2003 16 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LB064V02-A1. In addition
the figures in the next page are detailed mechanical drawing of the LCD.

Horizontal 145.5 ± 0.5mm

Outside dimensions Vertical 111.5 ± 0.5mm
Depth 6.0 ± 0.3mm
Horizontal 133.8 ± 0.5mm
Bezel area
Vertical 101.1 ± 0.5mm
Horizontal 130.56mm
Active display area
Vertical 97.92mm
Weight(approximate) 160g(Typ.), 170g(Max.)
Hard coating(3H)
Surface Treatment Anti-glare treatment of the front polarizer
Haze(13%)

Ver1. 2 MAR. 19, 2003 17 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

<FRONT VIEW>

Ver1. 2 MAR. 19, 2003 18 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

<REAR VIEW>

Ver1. 2 MAR. 19, 2003 19 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

<DETAIL DESCRIPTION OF SIDE MOUNTING SCREW>

TOP CASE (SUS 304)

Panel

Supporter Main (PC)

4-M2
Bottom Cover (AL5052)

Notes : 1. Screw plated through the method of non-electrolytic nickel plating is preferred
to reduce possibility that results in vertical and/or horizontal line defect due to
the conductive particles from screw surface.

Ver1. 2 MAR. 19, 2003 20 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

6. Reliability

Environment test condition

No. Test Item Conditions

1 High temperature storage test Ta= 60°C 240h

2 Low temperature storage test Ta= -20°C 240h

3 High temperature operation test Ta= 50°C 50%RH 240h

4 Low temperature operation test Ta= 0°C 240h

5 Vibration test Sine wave, 10 ~ 500 ~ 10Hz, 1.5G, 0.37oct/min

(non-operating) 3 axis, 1hour/axis

6 Shock test Half sine wave, 180G, 2ms

(non-operating) one shock of each six faces(I.e. run 180G 2ms
for all six faces)

7 Altitude
operating 0 - 10,000 feet(3048m)
storage / shipment 0 - 40,000 feet(12,192m)

{ Result Evaluation Criteria }

There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.

Ver1. 2 MAR. 19, 2003 21 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

7. International Standards
7-1. Safety
a) UL 1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995.
Standard for Safety of Information Technology Equipment Including Electrical Business Equipment.
b) CAN/CSA C22.2 No. 950-95 Third Edition, Canadian Standards Association, Jan. 28, 1995.
Standard for Safety of Information Technology Equipment Including Electrical Business Equipment.
c) EN 60950 : 1992+A1: 1993+A2: 1993+A3: 1995+A4: 1997+A11: 1997
IEC 950 : 1991+A1: 1992+A2: 1993+A3: 1995+A4: 1996
European Committee for Electrotechnical Standardization(CENELEC)
EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical
Business Equipment.

7-2. EMC

a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical

and Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards
Institute(ANSI), 1992
b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of
Information Technology Equipment.“ International Special Committee on Radio Interference
c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of
Information Technology Equipment.“ European Committee for Electrotechnical Standardization
(CENELEC), 1998

Ver1. 2 MAR. 19, 2003 22 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

8. Packing
8-1. Designation of Lot Mark
a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE
D : YEAR
E : MONTH
F,G : PANEL CODE
H : ASSEMBLY CODE
I,J,K,L,M : SERIAL NO.

Note:
1. YEAR

YEAR 97 98 99 2000 2001 2002 2003 2004 2005 2006 2007

Mark 7 8 9 0 1 2 3 4 5 6 7

2. MONTH

MONTH Jan. Feb. Mar. Apr. May. Jun. Jul. Aug. Sep. Oct. Nov. Dec.

Mark 1 2 3 4 5 6 7 8 9 10 11 12

b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one box : 20 pcs

b) Box Size : 325mm X 271mm X 197mm

Ver1. 2 MAR. 19, 2003 23 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

9. PRECAUTIONS
Please pay attention to the following when you use this TFT LCD module.

9-1. MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force(ex. Twisted stress) is not applied
to the module.
And the case on which a module is mounted should have sufficient strength so that external force
is not transmitted directly to the module.
(3) Please attach a transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not describe because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit
break by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are determined
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
(10) If there are some problems by using system bracket, system bracket should be first modified
and then LCD module reconfirmed under mutual approval .

9-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to
polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference
shall be done by system manufacturers. Grounding and shielding methods may be important to
minimized the interference.

Ver1. 2 MAR. 19, 2003 24 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

9-3. ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain
that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.

9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.

Ver1. 2 MAR. 19, 2003 25 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

11. IIS (Incoming Inspection Standard)

11.1. Inspection Method

11.1.1. Ambient conditions

a. Temperature : 20~25
b. Humidity : 65 ±5 % RH
c. Illumination : Single 20W fluorescent lamp non-directive
(300 to 700 Lux)

11.1.2. Viewing distance

The distance between the LCM and the inspector’s eyes shall be at least 30-50Cm.

11.1.3. Viewing Angle

The inspection shall be conducted within normal viewing angle range.
Refer to 16pages for viewing angle.

11.1.4. Measurement mode

Inspection method is based on transmissive mode only.

11.2 Inspection Criteria

11.2.1. Dot Defect

11.2.1.1. Bright Dot

Dots(sub-pixels) which appeared brightly in the screen when the LCM
displayed with dark pattern.
- R,G or B 1 dot ------------------------------------ 4 Max
- Adjacent 2 dots ------------------------------------ 1 Max
- Total amount of Bright dots ---------------------- 4 Max
- Minimum Distance between bright dots ------ Within 20 mm, Max 2

11.2.1.2. Dark Dot

Dots(sub-pixels) which appeared darkly in the screen when the LCM
displayed with bright pattern.
- 1 dot -------------------------------------------------- 4 Max
- Adjacent 2 dots ------------------------------------- 1 Max
- Total amount of Dark dot ------------------------- 4 Max
- Minimum Distance between dark dots -------- Within 20 mm, Max 2

11.2.1.3. Total amount of Dot Defects ----------------------- 8 Max(Combination)

Note) a. Every dot herein means Sub-Pixel(Each Red,Green, or Blue Color)

b. Bright & Dark dots are larger than half sub-pixel.
(Dots smaller than half sub-pixel are not counted as a defect dots.)

Ver1. 2 MAR. 19, 2003 26 / 27

 LB064V02-A1
Liquid Crystal Display

Product Specification

11.3. Polarizer Defects

Items Criteria

Scratches Linear

Dent Circular 0.2 ≤ D ≤ 0.5, n ≤ 4 , 0.5 ≤ D ≤ 1.0, n ≤ 1

Note) W : Width
L : Length
b D : Average diameter
a. Average Diameter n : Number of Defects
D = a+b a
2

b. Linear : a 2b , Circular : a ≤ 2b
c. Extraneous substances which can be wiped out, like Finger Print, Particles, are not
considered as a defect.
d. Defects which is on the Black Matrix(outside of Active Area) are not considered as a defect.

11.4 Foreign Material

Items Criteria

Foreign Linear ≤ ≤ ≤ ≤
Material
(Bright & Gray) Circular ≤ Φ ≤

Note) W : Width
L : Length
a. Average Diameter b D : Average diameter
n : Number of Foreign Material
D = a+b
N : Number of Pixels on which
2 a Foreign Material resides
Φ :Distance of Other
b. Linear : a 2b , Circular : a ≤ 2b Foreign
Material
c. In case of Linear Foreign Material, both length(L) and number of pixels(N) are used as criteria
for the sake of inspection convenience.
d. The distance between inspector’s eyes and screen is 30cm(11.8inch)

11.5. Line Defect

All kinds of line defects such as vertical, horizontal or cross are not allowed.

11.6. Bezel Appearance

Scratches, minor bents, stains, particles on the Bezel frame are not considered as a defect.

11.7. Others
Issues which is not defined in this criteria shall be discussed with both parties, Customer and Supplier,
for better solution.

Ver1. 2 MAR. 19, 2003 27 / 27