8/8/2019 KlasOS Initial Configuration
Home (/s/)
KlasOS Initial Configuration
May 5, 2019 • Knowledge Base
Content
Background
This article provides instructions for initial configuration using the KlasOS command line interface (CLI). Operations such as
adding IP address to an interface, configuring a hostname and configuring SSH for remote access are covered.
Adding an IP Address to an Interface
To configure an interface with an IP address using the KlasOS CLI, follow these steps:
1. Press Return or Enter once you see the Press RETURN to get started message. The following prompt is displayed:
KlasOS>
2. Use the enable command to get to Privileged mode.
KlasOS> enable
KlasOS#
3. Enter configuration mode using the following commands.
KlasOS#configure terminal
4. Enter interface configuration mode using the following commands.
KlasOS(config)# interface Ethernet 0/0
5. Add a static IP address and exit interface configuration mode using the following commands.
https://helpdesk.klastelecomgov.com/s/article/klasos-initial-configuration1 1/4
8/8/2019 KlasOS Initial Configuration
KlasOS(config-if)# ip address 192.168.1.1 255.255.255.0
KlasOS(config-if)# exit
6. Check if the configuration has been applied by using the show ip interface brief command.
KlasOS# show ip interface brief
Interface IP-Address Status Protocol
Dot11Radio0 Device not found N/A
Ethernet 0/0 192.168.1.1/24 up up
Ethernet 0/1 unassigned up up
Ethernet 0/2 unassigned up up
Ethernet 0/3 unassigned up up
Ethernet 1/0 unassigned up up
Ethernet 1/1 unassigned up up
Ethernet 2/0 unassigned down down
Ethernet 2/1 unassigned down down
Ethernet 2/2 unassigned down down
Ethernet 2/3 unassigned down down
Tether 0 pending down down
KlasOS#
Configuring a Hostname
To configure a Hostname in KlasOS, follow this procedure:
NOTE: If no device hostname is configured, KlasOS uses the factory-assigned default hostname which is the product name
(e.g. "TRX-R6") or else "KlasOS"
1. Enter configuration mode using the following commands.
KlasOS# configure terminal
2. Assign or modify the hostname of the device using the following commands.
Router(config)# hostname MyDevice
3. (Optional) Return to privileged mode.
KlasOS(config)# end
https://helpdesk.klastelecomgov.com/s/article/klasos-initial-configuration1 2/4
8/8/2019 KlasOS Initial Configuration
Configuring SSH For Remote Access
To configure SSH v2 using the KlasOS CLI, follow these steps:
1. Enter configuration mode using the following commands.
KlasOS# configure terminal
2. Configure the DNS domain of the router.
KlasOS(config)# ip domain-name mydomain.com (http://mydomain.com)
3. Add a local username and password using the following command.
KlasOS(config)# username klas secret klas
4. Generate the SSH key to be used using the following commands.
KlasOS(config)# crypto key generate rsa general-keys modulus 2048
% The key modulus size is 2048 bits
% Generating 2048 bit RSA keys, keys will be non-exportable...[OK]
KlasOS(config)#
5. Add the aaa new-model command which causes the local username and password on the router to be used.
KlasOS(config)# aaa new-model
6. Add the aaa authentication login command to enable AAA authentication and use local username and password,
as shown.
KlasOS(config)# aaa authentication login default local
7. (Optional) Return to privileged mode.
KlasOS(config)# end
KlasOS#
8. Use the show ip ssh command to display the status of SSH server.
KlasOS# show ip ssh
SSH Enabled - version 2
Authentication timeout: 60s secs; Authentication retries: 3
NOTE: Telnet is disabled and only SSH is supported.
https://helpdesk.klastelecomgov.com/s/article/klasos-initial-configuration1 3/4
8/8/2019 KlasOS Initial Configuration
Was this article helpful? 0 0
Files (0)
Contact Us
Contact Support
Government
Support Phone:
+1 703 881 3156
Toll-Free: 844-411-KLAS (5527)
Email Support (mailto:[email protected])
Transportation
Support Phone:
U.S. +1 202 754 8732
EMEA: +353 1 685 5734
Email Support (mailto:[email protected])
https://helpdesk.klastelecomgov.com/s/article/klasos-initial-configuration1 4/4
