HvacLoadExplorer V1.1.

USER’S GUIDE

For updates, go to:

http://www.mae.okstate.edu/hvac
 TABLE OF CONTENTS
Chapter Page

I. INTRODUCTION 1

II. INSTALLATION OF HVACLOADEXPLORER 4

III. USING HVACLOADEXPLORER 5

3.1 Main window 6
3.2 Main Menu 8
3.2.1 File submenu 9
3.2.2 Edit submenu 10
3.2.3 Operations submenu 11
3.2.4 Units submenu 12
3.2.5 Calculate submenu 12
3.2.6 View submenu 14
3.2.7 Help submenu 15
3.3 Building Dialog Box 15
3.4 Location Dialog Box 17
3.5 Zone Dialog Box 19
3.6 Room Dialog Box 21
3.7 New Gain Dialog Box 23
3.8 Infiltration Information Dialog Box 24
3.9 Wall Information dialog Box 25
3.10 Window Information Dialog Box 29
3.11 Window Details Dialog Box 32
3.12 Layer Information Dialog Box 32
3.13 Wall construction library dialog Box 34
3.14 Wall other side temperature dialog Box 35
3.15 Other side room selection dialog Box 36
3.16 People Information Dialog Box 36
3.17 Light Information Dialog Box 38
3.18 Equipment Information Dialog Box 40
3.19 Daily Schedule Dialog Box 41
3.20 Notes Dialog Box 42
3.21 Result Display Dialog Box 43
3.22 Calculate For Building Dialog Box 46
3.23 Output Report Dialog Box 47
3.24 Select Loads Dialog Box 48
3.25 Select Zone/Room Dialog Box 48
3.26 Additional Information Dialog Box 49
3.27 Example of summary output 50
3.28 Generic Library Dialog Box 51
3.29 Add Layer Dialog Box 52
 3.30 Search Help Dialog Box 53

IV. CALCULATION OF RADIANT TIME SERIES FACTORS

AND RESPONSE FACTORS 54
 1

1.0– Introduction
Welcome to HvacLoadExplorer Version 1.1, the cooling/heating load calculation
software that accompanies the book “Heating, Ventilating, and Air Conditioning –
Analysis and Design, 6th Edition.” This software uses the heat balance method (HBM)
developed under ASHRAE Research Project 875 for calculating cooling and heating
loads in buildings. It also is capable of calculating conduction transfer function
coefficients and coefficients for the Radiant Time Series Method (RTSM), a simplified
method.
HvacLoadExplorer uses the load calculation “Engine”, developed by C.O.
Pedersen Associates, Urbana, Illinois. This is a Fortran program, compiled into a DLL,
capable of calculating the heating or cooling load for a single room. HvacLoadExplorer
provides a graphical user interface (GUI) that collects information for the building, then
will automatically call the Engine for each room, and then retrieves and collates the
results.
HvacLoadExplorer performs two types of calculations.
• First, it allows a user to run a cooling or heating load calculation for an entire
building to determine the cooling or heating loads and airflow rate of all the
rooms in a building or zone.
• Second, it allows a user to calculate the conduction transfer function
coefficients, response factors, radiant time series factors. The procedure for
radiant time series factors is discussed in chapter 4.

For purposes of load calculations, a building may be thought of as being

organized in a hierarchical fashion. That is, a building is made up of zones, zones are
made up of rooms, and rooms are made up of walls, roofs, floors, and other heat gain
elements such as people, lighting, equipment, and infiltration. In HVAC Load Explorer,
zones are collections of one or more rooms, all controlled to the same air temperature.
The primary purpose of zones in the program are to allow the user to compute total loads
for collections of rooms. For example, a user may wish to include all rooms served by a
 2

particular cooling coil in a single zone so that the peak load on the coil can be readily
determined.
Users of personal computers are well aware that computer file systems are also
organized hierarchically. Accordingly, the user interface for HVAC Load Explorer is
somewhat analogous to the user interface for the Windows File Explorer. There are two
views of the hierarchy in the building. Double-clicking on a zone will show all of the
rooms in the zone; double-clicking on a room will show all of the heat gain elements in
the room. The interface is described in Chapter 3 in more detail, but it should be
reasonably intuitive for most PC users.

Quick Start Guide

A few features that may not be obvious are discussed here. First, to start
describing a new building, go to the File menu and select “New”. This will ask you to
specify a file name. After this step, zones may be added to the building, rooms may be
added to the zone, and heat gain elements may be added to the room, with the “Add
Node” button shown in Figure 1.1.

Add Node Button

Fig. 1-1 Add Node Button

Jumping ahead (assuming many of the additional steps are intuitive) users need to
be aware that when they specify a wall, roof, or floor, it is important to specify an
 3

external boundary condition, as shown in Fig. 1-2. “TOS” should be used for exterior
surfaces; “TA” for interior surfaces1

Fig. 1-2 Setting the external boundary condition.

1
One difference between the heat balance method (HBM) and simplified methods is that, in the HBM, all
surfaces are described, because they are important for radiative/convective exchange and zone response. In
simplified methods, the zone response is usually pre-calculated in some fashion, so that interior surfaces
need not be specified.
 4

2.0 – Installation of HvacLoadExplorer

HvacLoadExplorer can be installed on a PC running Windows95,Windows98,
WindowsNT, Windows 2000, WindowsME, or Windows XP. The drive where
HvacLoadExplorer is to be installed needs to have 8.2 MB of free space. To install
HvacLoadExplorer from CD, follow the procedure given below.

• Put the accompanying CD in your CDROM drive

• Select “Run” from the start menu.
• Type D:\Setup in the text box. If your CD drive has a different name, change the ‘D’
to your CDROM drive letter.
• Press OK button
• Setup program will ask you to select the path where you want the HvacLoadExplorer
to be installed. By default, HvacLoadExplorer will be installed in the directory
Program Files\HvacLoadExplorer, which will also contain Two subdirectories:
• Database: contains the template building database file that is used for creating a
new building file and library database with libraries like, location library &
presets for the 24 hour schedules.
• TextFiles: which contains the three text files
• Default.txt: It contains the default setting for the location
• Param.txt: It contains the parameter values required for the programs.
• Timezone.txt: It contains the timezone values require for the locations.
 5

3.0 – Using HvacLoadExplorer

As mentioned above, the building may be considered to be organized in a
hierarchical fashion – the building has zones; zones have rooms; and rooms have heat
gain elements. The user interface of HvacLoadExplorer has been developed to have
some similarity to Windows File Explorer, which is also used to navigate a hierarchical
system, in this case consisting of directories and files, and with which most users will be
familiar. It has a tree view to show the hierarchy and relationships of the various elements
of a building and a list view to show the details of the levels selected in the tree view. For
example when the building is clicked in the tree view, it will show all the zones in the
building in the list view part of the main window. Click on a zone, and it will show all of
the rooms in the zone. In addition to navigation, input, and calculation of loads,
HvacLoadExplorer can display the results in both text and graphical forms. In the current
version, additional reporting features have also been added.

The main window, HvacLoadExplorer, of the program shown in Figure 3.1,

appears when the program starts. This window shows a representation of the data related
to a building. Like the Windows Explorer, the main window is divided in two main parts.
One part shows the tree view of the building, and the hierarchy of the different elements
in the building. List view shows a detail view of the current level selected in tree view.
Size of the tree view and list view can be changed just like Windows Explorer. All the
icons in the tree view as well as in the list view represent nodes or elements in the tree
and lists. So building, zones, rooms and gains are nodes.

This window also contains a toolbar and a menubar, as shown in Figure 3.2. It
also has a status bar with the loading indicator, which shows the status of the opening
process when a new file is opened. It shows the calculation status when the calculate
menu is selected.

3.1 Main Window

 6

Figure 3.1: Main Window of HvacLoadExplorer

Figure 3.2: Zoom View of Menu and Toolbar

 7

Figure 3.3: Zoom View Tree View

The relationship between different levels is shown in the tree view of the main
window. Double clicking on the any of the elements can bring up the dialog box with the
details of that specific node. Clicking on the + and - signs in the square box can expand
or fold the tree. For calculation purposes one must select an item in the tree view part of
the main window. Calculations for building, or any element at levels below building can
be selected. Cut and paste operations using the edit menu or shortcut keys can be
performed.

Figure 3.4 Zoom View of List View.

When a user clicks on an icon in the tree view part of the main window, all the
items one level below are shown in the list box except when the icon representing heat
gain (people, lights, equipment etc.) or wall are clicked, as those elements don’t have any
sub-elements. Double clicking on any element of the list view brings up the details about
that particular element. Cut and paste operations using the edit menu or shortcut key can
be performed.
 8

3.2 Main Menu

Following is the overview of the menu bar options. The menus are explained in
details in the following few pages along with the short cuts.
♦ File
♦ New
♦ Open
♦ Close
♦ Save As
♦ Backup
♦ Exit

♦ Edit
♦ Copy
♦ Paste

♦ Operations
♦ Add
♦ Details
♦ Delete

♦ Units
♦ SI
♦ IP

♦ Calculate
♦ Execute For Building
♦ Execute for zone
♦ Execute For Room
♦ View Output For Building
♦ Create Report File

♦ View
♦ Toolbar
♦ Status bar
♦ Load bar
♦ Large Icons
♦ Small Icons
♦ List
♦ Details
 9

♦ Help
♦ Contents
♦ Search Help On
♦ About

3.2.1 File Submenu

Figure 3.5 Zoom View of File Submenu

New
Shortcut keys: Ctrl+N
Function: Opens New Building File
Description: Brings up the new building dialog box with button to get the
location dialog box.

Open
Shortcut keys: Ctrl+O
Function: Opens Existing Building File
Description: Brings up the Windows standard open file dialog box showing
building files present.

Save As
Shortcut keys: -
Function: Saves a copy of the building (Changes current file to new copy)
Description: Saves a copy of the building under a new file name. Also changes
the current working file to the new file name
 10

Close
Shortcut keys: Ctrl+Q
Function: Closes Building File
Description: Closes the already opened building file so that user can open a new
building

Backup
Shortcut keys: Ctrl+U
Function: Saves a copy of the building
Description: Saves a copy of the building under new name. Retains the original
file as the current file

Exit
Shortcut keys: Ctrl+X
Function: Exits the application
Description: Closes the main window and exits the application

3.2.2 Edit Submenu

Figure 3.6 Zoom View of Edit Submenu

Copy
Shortcut keys: Ctrl+C
Function: Copies the selected element (i.e. building, zone, room, and gains).
Description: Select any icon in the tree view or list view, then use this menu to
copy the data related to that icon.
 11

Paste
Shortcut keys: Ctrl+V
Function: Pastes the copied element (i.e. building, zone, room, and gains).
Description: Select appropriate icon in the tree view, then use this menu to paste
the data already copied.

3.2.3 Operations Submenu

Figure 3.7 Zoom View of Operations Submenu

Add
Shortcut keys: Ctrl+A
Function: Adds New Element (i.e. building, zone, room, and gains)
Description: Add the element as a child (element one level below) of element
selected on the tree view controls. The type of new element
depends on the type of element selected by the user before using
this menu.

Details
Shortcut keys: Ctrl+L
Function: Shows details of the element (i.e. building, zone, room, and gains)
Description: Brings up the details of element selected on the tree view controls
or list view control.

Delete
Shortcut keys: Ctrl+D
Function: Deletes the element (i.e. building, zone, room, and gains)
 12

Description: Deletes the element selected in the tree view of the main window.
It also erases the corresponding entry in the building database.

3.2.4 Units Submenu

Figure 3.8 Zoom View of Calculate Submenu

SI
Shortcut keys: Ctrl+S
Function: Changes units to SI system.

IP
Shortcut keys: Ctrl+I
Function: Changes units to IP system.

3.2.5 Calculate Submenu

Figure 3.9 Zoom View of Calculate Submenu

Execute For Building

Shortcut keys: Ctrl+E
Function: Runs Load Calculation for the entire building
Description: Runs the simulation for the whole building, i.e. for all the rooms in
the building. It also stores the cumulative result, for all rooms, of
 13

the total air flow rate, cooling coil load (total, sensible and latent),
sensible heat load in the same building file.

Execute For Zone

Shortcut keys: Ctrl+ Z
Function: Runs Load Calculation for the selected zone
Description: Runs the simulation for the zone selected in the tree view. It shows
the result of the calculation immediately. These results are not
stored.

Execute For Room

Shortcut keys: Ctrl+R
Function: Runs Load Calculation for the specific room
Description: Runs the simulation for the room selected in the tree view. It
shows the result of the calculation immediately. These results are
not stored.

View Output For Building

Shortcut keys: Ctrl+W
Function: Views and prints results of the calculation for the entire building.
Description: It shows the calculation results done by the ‘Execute For building’
menu.

Create Report File

Shortcut keys: Ctrl+F
Function: Creates an output report.
Description: Performs the necessary load calculations, then creates an output
report file. The user can select to have either a text file or a comma
delimited file (CSV), which can be imported into a spreadsheet. A
wide range of options allows the reports to be customized.
 14

3.2.6 View Submenu

Figure 3.10 Zoom View of View Submenu

Toolbar
Function: Toggles the visibility of the toolbar

Status Bar
Function: Toggles the visibility of the status bar

Load Bar
Function: Toggles the visibility of the Load Bar

Large Icons
Function: Shows list view in the large icon form

Small Icons
Function: Shows list view in the small form

List
Function: Shows list view in the List form

Details
Function: Shows list view in the Detail form
 15

3.2.7 Help Submenu

Figure 3.11 Zoom View of Help Submenu

Contents
Function: Brings up the help contents window

Search Help On
Function: Brings up find help window

About HvacLoadExplorer
Function: Brings up the About dialog box.

3.3 Building Dialog Box

The building dialog box, shown in Figure 3.12, shows the details of a building.
The dialog box appears when either a new building is being created or the details of an
existing building is required. It can be used for setting the calculation option and location
details.

Figure 3.12 Building Dialog Box

 16

Name Of Building: User-specified name of the building.

Location: Brings up the dialog box related to the location data
Cooling Load Calculation: Uses the summer data of the location for the calculation
Heating Load Calculation: Uses the winter data of the location for the calculation.
Special Boundary Conditions: Brings up the dialog box with the schedule of the special
boundary temperatures for 24 hours. It stores the values
of special outside boundary temperatures at each hour of
the day. Walls that are specified to have an external
boundary condition of “TS” will utilize this temperature.
(It is also possible, with boundary condition “TIZ” to set
external boundary conditions for each surface or use
calculate values from free-floating rooms.

Only one mode, either heating or cooling, can be active at any time. However, the Create
Report command will cause the program to calculate both heating and cooling loads, if
requested. Clicking on ‘OK’ saves the changes if the new building is being created. The
user will then be prompted to enter the name of the file where all the data will be stored.
If the building is already created it saves the changes made in the file corresponding to
the building.
 17

3.4 Location Dialog Box

Figure 3.13 Location Dialog Box

The location dialog box, shown in Figure 3.13, appears when the ‘Location’
button on the New Building dialog is clicked. Locations are represented by the
geographical information about the location and the weather data for the summer and
winter conditions. All of these data can be selected from the library in one step, which
stores the details about the different locations. For additional U.S. and international
locations, refer to Appendix Table B-1 in the text or the 1997 ASHRAE Handbook of
Fundamentals. One can also add new locations in the library or modify them.
 18

Building City: Name of the city whose weather conditions are being applied for
the calculation purpose.
State: Name of the state where city is located.
Longitude: Longitude, in degree, for the location. Refer Table B-1 in appendix
B from text, for different locations

Latitude: Latitude, in degree, for the location. Refer Table B-1 in appendix B
from text, for different locations

Timezone: Timezone with respect to the Greenwich Mean Time for the
location. This is a combo box with preset values of timezones
commonly found with windows.
All the weather related conditions are for the summer and winter design conditions.

Dry Bulb Temperature: The peak design dry bulb temperatures for a location in the
summer or winter. Table B-1 in appendix B of text has the data for
different locations
Daily Range: The daily range for the variation of the dry bulb temperatures for a
location in the summer or winter. Table B-1 in appendix B of text
has the data for different locations
Wet Bulb Temperature: The wet bulb temperatures for a location in the summer and
winter. Table B-1 in appendix B of text has the data for different
locations
Ground Temperature: The surrounding ground surface temperatures for that location in
the summer and winter conditions, which helps calculating the heat
loss from the floors and walls in contact with the ground (in °C or
°
F).
Clearness: Suggested values of clearness are given in Figure 7-7 of the text
for non-industrial locations in the United States
 19

Ground Reflectivity: Ground reflectivity is the fraction of global horizontal solar

radiation reflected by the ground. Default value is 0.2.
Wind Speed: Wind speed (in m/s or mph) Default value is 3.35 m/s (7.5 mph)
for summer and 6.7 m/s (15 mph) for winter.
Wind Direction: Wind direction in degrees clockwise from north.
Month: any month can be selected for summer or winter. Note: all
buildings do not have peak cooling loads on July 21st! It may be
useful and necessary to check cooling loads in other months, even
December. If so, the “Summer month” would be set to be
December, and the cooling load would be calculated.
Days: any of the days can be selected from the combo box.
Default for date is 21st July for summer and 21st January for winter.
For summer design conditions, daylight savings switch can be set
to true/false.
Clicking on the ‘Default’ button can save the current location as the default
location for the program. It writes all the information to the text file called default.txt in
the directory named as ‘textfiles' in the home directory of the application. Clicking on the
‘OK’ button saves the location changes with the building database file. Clicking on the
‘Library’ button will bring up the library of locations, from where user can select the
location and then use it. User can also add new entries or modify the existing entries in
the library. Clicking on the ‘Notes’ button will bring up the notes dialog box where user
can add extra information about the location.

3.5 Zone Dialog Box

The zone dialog box, shown in Figure 3.14, appears when a new zone is to be
added by selecting building Element in the tree view and clicking the ‘Add Node’ menu
or details of an existing zone are shown.
 20

Figure 3.14 Zone Dialog Box

Zone Name: Name of the zone

Zone North Axis: orientation of zone with respect to north axis, measured in degrees
clockwise direction. This rotation is applied to the facing angles of
all the wall elements as shown in Figure 3.15. This allows a zone
oriented like that shown in the right-hand-side of Fig 3.15 to be
input as if it is oriented like that on the left-hand-side of Fig. 3.15.
Then, the correct rotation can be specified by inputting the angle θ
as the Zone North Axis.

Figure 3.15 Zone North Axis Rotation

System Air Supply Temperature Cooling: Supply air temperature for the zone to be
used when calculating air flow rates required to meet cooling loads
(in °F or °C).
 21

System Air Supply Temperature Heating: Supply air temperature for the zone to be
used when calculating air flow rates required to meet heating loads
(in °F or °C).
Normal zone option: On selecting this option all the rooms in this zone are conditioned
according to the temperature schedule, and cooling or heating
loads will be calculated for the rooms in this zone.

Free Floating zone: On selecting this option the rooms in this zone are not conditioned.
The temperatures for each room are calculated based on the
interaction with the boundary conditions. These temperatures can
be viewed by clicking on the “Temperatures” button on the room
dialog box. This option is used to calculate air temperatures for
attics, garages, etc. These temperatures can then be used as
boundary temperatures for other rooms.

Clicking on the ‘Edit’ Button will bring up the dialog box for a 24-hour schedule of the
interior temperature. Clicking the‘Notes’ button will bring up the notes dialog box where
user can add the extra information about the zone. Clicking on ‘OK’ will save the
information about the zone and exit the dialog or it will create a new zone and exit the
dialog box. A new node is also created in the tree view of the main window.

3.6 Room Dialog Box

The room dialog box, shown in Figure 3.16, appears when a new room is to being
added by selecting a zone element in the tree view and clicking the ‘Add Node’ menu or
details of an existing room are shown.
 22

Figure 3.16 Room Dialog Box

Room Name: Name of the Room

Room Ceiling Height: Height of the room for volume (m or ft).
Temperatures: Shows the temperatures of the room if the room is in a free floating
zone. If the room is not in a free floating zone the button is
disabled

Clicking ‘Notes’ button will bring up the notes dialog box where user can add
extra information about the zone. Clicking on ‘OK’ will save the information about the
room and exit the dialog if the room already exits or it will create a new room and exit
the dialog box. A new icon, representing the newly added room, is created in the tree
view of the main window.
 23

3.7 New Gain Dialog Box

Figure 3.17 New Gain Dialog Box

The New Gain dialog box, shown in Figure 3.17, comes up when new heat gain is
to be added in the selected room. There are eight different types of gains, which can be
added, and depending on the button clicked, a dialog corresponding to the selected gain is
shown.

Figure 3.18 New Gain Dialog Box with ‘Done’ Button

Many gains can be added to the room without exiting this dialog box. When user enters
the first node the ‘Done ‘ Button appears.
 24

3.8 Infiltration Information Dialog Box

Figure 3.19 Infiltration Information Dialog Box

The infiltration information dialog box, shown in Figure 3.19, appears when the
user adds infiltration or outdoor ventilation heat gain to the room or edits the details of
existing gains. This box can be used to enter either infiltration (heat gain to the room) or
ventilation (heat gain to the system, but proportioned at the room level.)

Infiltration Name: User-specified name of the infiltration/ventilation gain

Rate of Air Change Options
Air Changes/Hour: Peak flow rate in ACH. Room volume is taken from the
product of the floor area and ceiling height
Cubic Foot/min: Peak flow rate in CFM
CFM/person: Peak flow rate in CFM/person. The number of people is
obtained from the people schedule in the people gain.
Include in cooling check box: Specifies if the gain is to be used while calculating the
cooling load
Include in heating check box: Specifies if the gain is to be used while calculating the
heating load
 25

Infiltration is the uncontrolled flow of air through unintentional openings such as

cracks around windows and doors. There may be situations where outdoor air is
intentionally supplied directly to the space for indoor air quality or other purposes. In this
case, the outdoor air produces a heating or cooling load on the space in the same way as
infiltration air and should be treated as such.

For purposes of the program, ventilation air is outdoor air that is introduced at the
system. In this case, it affects the coil load, but does not affect the room load. However,
because outdoor air requirements for IAQ purposes are often specified on a per person
basis, it is convenient to be able to enter the quantity at the room level. Outdoor air
requirements for commercial facilities are given in the Table 4-2 of the text.

One can specify whether the air inflow should be considered as infiltration or
outdoor air entering the mixing box by checking the checkbox on the dialog box. If the
checkbox is checked then the gain is considered as infiltration, otherwise as outdoor air
entering the mixing box upstream of the coil.

Clicking on the ‘Edit’ button will bring up the dialog box for a 24-hour schedule
for the selected day. Enter the fraction of the peak rate for each hour. Clicking ‘OK’ will
save the information in the database and exit. Clicking the ‘Notes’ button will bring up
the notes dialog box.
.

3.9 Wall Information Dialog Box

The wall information dialog box, shown in Figure 3.20, is shown when a new
wall is to be added or the details related to the existing wall are to be displayed.
 26

Figure 3.20 Wall Information Dialog Box

Wall Name: User-specified name of the wall

Tilt: Tilt is the angle made by the wall with the horizontal in degrees.
Default is 900.
Facing Direction: Facing direction is the angle made by the normal vector of wall
with north, in degrees clockwise . 0° represents a north facing wall;
90° represents an east-facing wall; 180° represents a south-facing
wall; 270° represents a west-facing wall, etc.
Solar Aborptivity out: The solar (shortwave) absorptivity of the outside surface. It will
have values between 0 and 1, with a default is 0.9.
SW Aborptivity in: The solar (shortwave) absorptivity of the inside surface. It will
have values between 0 and 1, with a default is 0.9.
 27

LW Emissivity in: The emissivity for thermal (longwave) radiation of the inside
surface. It will have values between 0 and 1, with a default is 0.9
LW Emissivity out: The emissivity for thermal (longwave) radiation of the outside
surface. It will have values between 0 and 1, with a default is 0.9
External Boundary
Condition: Setting this parameter controls the boundary conditions on the
outside of the wall. The different options are discussed below.
Area Specification: The wall area can be either directly specified or specified in terms
of length and width.
Other side Temperatures: Brings up a dialog box where the other side temperature of the
wall to be used can be specified. This is enabled only if the TIZ
external boundary condition is specified for the wall.

This dialog box is also used for adding other elements-- Floor, Roof and Thermal
Mass2. The default tilt in case of floor is 180° and in case of roof is 0°. In case of floor and
thermal mass the windows button is disabled, as these types of elements cannot have a
window.
A variety of exterior boundary conditions may be selected.:
TOS Used for exterior walls and roofs. The outside of the wall will be exposed
to outdoor air, wind, and solar radiation.
TA Used for interior walls, ceilings, and floors, when the space on the other
side is controlled to approximately the same conditions. A surface with
this external boundary condition will have no net heat transfer, but may
store and release energy.
TG Used for basement walls, basement floors, and slab-on-grade floors.
These surfaces will have the user-specified ground temperature imposed
on the outside.
TB Used for walls, ceilings and floors, when the space on the other side is at a
substantially different temperature. In this case, the space temperature on

2
Thermal mass is usually used to approximately model the effects of interior furnishings. It has the effect
of providing some thermal storage, but also enhancing radiative/convective heat exchange. The surface
area of the thermal mass should represent the total thermal mass exposed to the zone air.
 28

the other side is set at the Building Dialog Box as a “Special Outside
Condition”. An example application might be a wall separating an office
space from a refrigerated warehouse. When the office is being described,
the wall boundary condition would be set as “TB”, and from the Building
Dialog Box, “Special Outside Conditions” would be set to the refrigerated
warehouse air temperature. TIZ may also be used for this purpose with
additional flexibility.
TSS The TSS boundary condition uses the outside DB temperature without
solar radiation or wind. This might be used for walls with well-ventilated,
uncontrolled spaces on the other side, e.g. a garage. It might also be used
for walls that are always shaded by a large overhang or very tall building.
TIZ Like the TB boundary condition, the TIZ boundary condition is used when
the space on the other side is at a substantially different temperature.
However, the TIZ condition allows the other side temperatures to be
specified individually for each wall. Alternatively, they can be calculated
using a free floating room analysis. In a house, this would be useful for a
ceiling below the attic. In the conditioned room, the ceiling can be set to
have a TIZ boundary condition, with the other side temperature coming
from the attic. In the attic, the floor can be set to have a fixed or
scheduled other side temperature equivalent to the controlled temperature
in the conditioned spaces..

Window area is subtracted from the wall area to get the effective area of the wall.
So the total area bounded by wall’s external edges should be entered.

Clicking the ‘Windows’ button brings up the window information dialog box for
that particular wall. Clicking on the ‘Layer Information’ brings up the layer information
dialog box where the wall construction corresponding to that particular wall is specified.
Layer-by-layer information is usually most conveniently entered into the library, then
chosen for repeated application inside the building. Clicking ‘Notes’ button will bring up
the notes dialog box .
 29

Clicking on the ‘Library’ button brings up the library of walls, floors and roofs
from which user can pick from different construction types.

Also, while on the subject of walls, roofs, and floors, it should be noted that all of
the walls, roofs, and floors of a room should be included, but:
1. The program will only allow 6 walls, roofs, and floors, plus a thermal
mass surface. Therefore, some surfaces might have to be combined.
Interior surfaces of the same construction may be lumped together (by
specifying their total area) regardless of surface orientation. Exterior
surfaces should only be lumped together if they have the same surface
orientation.
2. The program must have at least a floor and a wall or roof to run.

3.10 Window Information Dialog Box

Figure 3.21 Window Information Dialog Box

 30

The window information dialog box, shown in Figure 3.21, appears when a new
window is added or details of an existing window are to be displayed.

External shading surfaces reduce the transmitted solar radiation by intercepting

the direct beam component of the solar radiation. One of the most common shading
devices is a window overhang.. The simplified overhang model included in the program
assumes that the overhang is long relative to the width of the window. Thus only the
horizontal projection of the overhang is specified. It also assumes the window is square
so only the area of the window is expected.

Name: This is a name of the window

Area: Area of the window in m2 or ft2. This area is subtracted from the
respective wall area to get the effective wall area. Refer to Figure 3.22.
Overhang Width: The distance the overhang protrudes out from the face of the wall. The
overhang is assumed to extend far enough from side to side to shade the
entire width of the window (m or ft). Refer to Figure 3.22.
Reveal: Specifies the distance the outside surface of the window is set back from
the outside surface of the wall. This can produce a shadow on the window
that must be taken into account when calculating the solar gain (m or ft).
Distance from the overhang specifies how far above the top edge of the
window the overhang is attached to the wall (m or ft). Refer to Figure
3.22.
Normal SHGC: The Normal Solar Heat Gain Coefficient (SHGC) for the window.
LW Emissivity out: Specifies the emittance for long wavelength radiation for the
outside. This value is used for the surface heat balance calculation.
LW Emissivity in: Specifies the emittance for long wavelength radiation for the
inside. This value is used for the surface heat balance calculation.
U Factor: Specifies the U-Factor for the material used for the window (w/m2 or
Btu/[hr.ft2]). The ‘U factor’ specified for the window should not be zero.
 31

Transmittance of inside shade: The fraction of the solar radiation transmitted through the
window, which is, in turn, transmitted through the shade/drapery into the
room. The remainder is assumed to be convected to the zone air.

At present, the procedure utilized in the program does not match the method
described in the book. Given the information in the book, the best approach is probably
to simply multiply the SHGC by the IAC and enter the modified value as the SHGC.
Then, the transmittance of inside shade should be set to 1.

Clicking ‘Library’ brings up the Library of windows. Clicking ‘Delete’ deletes the
window details and exits the dialog box. Clicking ‘OK’ saves the information and then
exits the dialog box. Clicking the ‘Info’ button brings up the window details dialog box,
shown in the next section.

The ‘Delete’ button is not shown when the new window is being created. The
caption of the dialog changes depending whether the new window is being created or the
details of the existing one are being shown.
 32

3.11 Window Details Dialog Box

Figure 3.22 Window Details Dialog Box

The windows details dialog box, shown in Figure 3.22, comes up when user clicks
on the ‘Info’ button on the windows dialog box.. Clicking on ‘Done’ exits the dialog
box.

3.12 Layer Information Dialog Box

Figure 3.23 Layer Information Dialog Box

The layer information dialog box, shown in Figure 3.23, appears when the user
clicks the ‘Layer Information’ button on the wall dialog box. The layers are specified
from the outside of the surface to the inside.
 33

Clicking the ‘Insert Before’ will insert a new layer before the layer selected.
Then all the required values can be entered in this new row. Clicking the ‘Insert After’
will insert a new layer after the layer selected. Then all the required values can be filled
entered in this new row. Clicking the ‘Library’ button will bring up the external library of
materials from which a layer can be selected. Clicking ‘Delete’ will delete the selected
layer. ‘Done’ exits the dialog box. All data for a layer should be filled in before
proceeding. The appropriate units are shown in the column headers.

In some cases, the user may be interested in adding a purely resistive layer, e.g.
fiberglass insulation. In that case, the user may set the specific heat and density to zero,
set the conductivity to 1 and set the thickness to the desired resistance.

Table 5.1a and Table 5.1b of the text have values for thermal properties of
different materials normally used.
 34

3.13 Wall construction library dialog box

Figure 3.24 Wall Construction library Dialog Box

This window is brought up when the user clicks the construction library button
from the wall information dialog box. The user can then select a construction for the
wall. Further information about libraries is given in the “Generic library section” below
If the user wishes to change all the walls in the building with a certain
construction to different one then the user can select the “apply to all walls with this
construction” option before selecting the wall.
 35

3.14 Wall other side temperature dialog box

Figure 3.25 Wall other side temperature Dialog Box

This dialog box is shown when the user selects the TIZ boundary condition for a
wall and clicks the ”Other side temperatures” button.
This dialog allows the user to specify a constant or scheduled set of other side
temperatures, or to specify a free floating room from which to take the temperatures as
the boundary condition.
 36

Clicking on the “Free Floating room temperatures” option brings up a dialog box
that lets the user select the free floating zone and room. The user can then the change the
selected room by clicking the “Change” button.
Clicking on the “Custom temperatures” option lets the user edit the temperature
for each hour.

3.15 Other side room selection dialog box

Figure 3.26 Wall other side temperature dialog box

This dialog box is brought up when the free floating room is selected in the other
side temperature dialog box. The Available zones list box is populated with all the free
floating zones in the building. The select room list is populated with the rooms in the
zone selected in the list box. The user can then select the desired room by clicking on the
arrow.

3.16 People Information Dialog Box

The people information dialog box, shown in Figure 3.24, appears when either
new heat gain due to people is added or the details of existing people heat gain due to
people are to be displayed.
 37

Figure 3.27 People Information Dialog Box

Name: Name of heat gain due to people

Activity: Specifies the total sensible and latent heat gain per person
(Watts or Btu/hr)
Peak Number of People: Specifies the maximum number of people at any time
during the day. This is used along with the fraction
specified in the schedule to create a 24-hour schedule of the
people in the room.

Sensible Heat Fraction: Specifies the fraction of heat gain due to people that is
sensible often referred to as the sensible heat factor or
sensible heat ratio.
Latent Heat Fraction: Specifies the fraction of heat gain due to people that is
latent.
The latent heat fraction and sensible heat fraction must sum up to one.

Radiant Heat Fraction: Specifies the fraction of the sensible heat gain that is
radiative.
 38

Convective Heat Fraction: Specifies the fraction of the sensible heat gain that is
convective.
Include in cooling check box: Specifies if the people gain is to be used while calculating
the cooling load
Include in heating check box: Specifies if the people gain is to be used while calculating
the Heating load

The radiant heat fraction and convective heat fraction must sum up to one.
Typical metabolic heat generations for various activities are given in Table 4.4 of the
text. Also rates of occupants of conditioned spaces are given in the Table 8.7 of the text.

Clicking on the ‘Edit’ button will bring up the dialog box for the 24-hour schedule for
the day. The fraction of the peak heat gain is entered for each day. Clicking ‘OK’ will
save the information and exit. Clicking the ‘Notes’ will bring up the notes dialog box to
add the extra information about the people gain.

3.17 Light Information Dialog Box

Figure 3.28 Light Information Dialog Box

 39

The light information dialog box, shown in Figure 3.25, appears when either new
lighting heat gain is added or the details regarding existing lighting heat gain are to be
displayed. Since the light is often the major internal load component, an accurate estimate
of the space heat gain it imposes is needed.

Peak Light Gain: The peak lighting heat gain in the design day schedule. This value
is used along with the fraction of the peak heat gain to create the
24-hour schedule of the light gain (W/m2 or Btu/[hr.ft2]).
SW Radiant Fraction: The fraction of lighting heat gain in the short wavelength (visible)
radiation form
LW Radiant Fraction: The fraction of lighting heat gain in the long wavelength (infrared)
radiation form
Convective Heat Fraction: The fraction of lighting heat gain in the convective heat form

Fraction of Heat Returned to the Duct: The fraction of total heat that goes directly
to the return air duct.
Include in cooling check box: Specifies if the light gain is to be used while calculating the
cooling load
Include in heating check box: Specifies if the Light gain is to be used while calculating
the heating load

Convective heat fraction, LW Radiant Fraction and SW Radiant heat fraction

must sum to one.
Clicking on the ‘Edit’ button will bring up the dialog box for the 24-hour
schedule for the fraction. Clicking ‘OK’ will save the information and exit. Clicking the
‘Notes’ will bring up the notes dialog box to add the extra information about the light
gain. Recommended radiative and convective fractions are given in Table 8.20 of the
text.
 40

3.18 Equipment Information Dialog Box

Figure 3.29 Equipment Information Dialog Box

The dialog box, shown in Figure 3.29, comes up when either new equipment heat
gain is added or the details regarding existing equipment heat gain are to be displayed.

Peak Equipment Load: Specifies the peak equipment heat gain in the design day
schedule at any time during the day. This is used along with
the fraction specified below in the schedule to create a 24-
hour schedule of the equipment gain in the room (w/m2 or
Btu/[hr.ft2]).
Sensible Heat Fraction: Specifies the fraction of heat gain due to equipment that is
sensible.
Latent Heat Fraction: Specifies the fraction of heat gain due to equipment that is
latent.
The latent heat fraction and sensible heat fraction must sum up to one.
Radiant Heat Fraction: Specifies the fraction of the sensible heat gain that is
radiative.
Convective Heat Fraction: Specifies the fraction of the sensible heat gain that is
convective.
 41

Include in cooling check box: Specifies if the Equipment gain is to be used while
calculating the cooling load
Include in heating check box: Specifies if the Equipment gain is to be used while
calculating the heating load
The radiant heat fraction and convective heat fraction must sum up to one.
Clicking on the ‘Edit’ button will bring up the dialog box for the 24-hour schedule
for the fraction. Clicking ‘OK’ will save the information and exit. Clicking ‘Notes’ will
bring up the notes dialog box to add the extra information about the equipment gain.

3.19 Daily Schedule Dialog Box

Figure 3.30 Daily Schedule Dialog Box

 42

The dialog box, shown in Figure 3.30, appears whenever a 24-hour schedule is to
be displayed. It is used for displaying the fraction of peak gain for lighting, equipment
and people heat gains and displaying temperatures for the special outside boundary
conditions and internal temperatures.

When it is used for fractions it checks whether all the values in the dialog box are
between 0 and 1.

Clicking on the ‘Library Schedules’ brings up the library database, which give
several preset schedules for different conditions. ‘Done’ saves the value and exits the
dialog box. Clicking on the ‘Set All Fields to =>’ button sets the values in the all the text
fields.

3.20 Notes Dialog Box

Figure 3.31 Notes Dialog Box

The dialog box, in Figure 3.31, shows up whenever there is extra information to
be stored related to any element of the building.

Clicking ‘OK’ saves the information entered and exits the dialog box. The
changed value is stored in buffer. The change reflects in database only when ‘OK’ on the
parent dialog box is clicked.
 43

3.21 Result Display Dialog Box

Figure 3.32 Result Display Dialog Box Showing graph

Figure 3.33 Result Display Dialog Box Showing Text

 44

Figure 3.34 Result Display Dialog Box Showing graph in Line mode

Once a cooling or heating load calculation is performed for a room, zone, or

building, the results will be displayed in a dialog box, as shown in Figures 3.32-3.34.
The actual results displayed vary, depending on what type of load is calculated. Also,
some outputs, such as CTF coefficients are only given in the text display. For whole
building calculations, all loads can be displayed in the text display by selecting “Show all
rooms and zones.”

For an entire building calculation, the following outputs are displayed, either as cooling
loads or heating loads:
• Total Coil Load: Total load on coil (W or Btu/hr).
• Sensible Coil Load: Sensible load on coil (W or Btu/hr).
• Latent Coil Load: Latent load on coil (W or Btu/hr).
• Show All: Shows report about all the rooms. For each room the sensible load,
airflow required, coil loads (total, sensible and latent) are shown.
 45

For zone load calculations, all of the outputs for the building are displayed, plus the
required air flow rate for the zone.

For a room load calculation, the following outputs are displayed. For loads, they will be
given as either cooling or heating loads.
• Supply Air Flow Rate: supply air flow rate for the room (m3/s or CFM)
• Room Total Load: The total cooling or heating load for the room as determined
by the heat balance method (W or Btu/hr).
• Room Sensible Load: The sensible cooling or heating load for the room as
determined by the heat balance method (W or Btu/hr).
• Room Latent Load: The latent cooling or heating load for the room as determined
by the heat balance method (W or Btu/hr).
• Sensible Cooling Coil Load: Sensible load on coil (W or Btu/hr).
• Latent Cooling Coil Load: Latent load on coil (W or Btu/hr).
• RTF Coef I Loads: RTS coefficients for processing internal gains. As described
in Chapter 8, these coefficients may also be used for processing solar heat gains.
• RTF Coef Solar Loads: RTS coefficients for processing solar gains
• Conduction Transfer Coefficients: Conduction transfer coefficients for all the
surfaces. (Only shown in the text display)
• Response Factors: Steady periodic response factors for RTS calculation, all
surfaces (Only shown in the text display)

In addition to these reports, additional reporting capabilities are described below

in Section 3.23. One can also cut and paste the information from the text box and use it
to plot or print. The text data can be printed out using the ‘Print’ button on the dialog box.
 46

3.22 Calculate For Building Dialog Box

Figure 3.35 Calculate For Building Dialog Box

The dialog box, shown in Fgure 3.35, appears when the menu for running the
calculation for the entire building is chosen. Zone and room names are displayed as the
calculations are performed, and the number of rooms remaining and completed are also
displayed.
 47

3.23 Output Report Dialog Box

Figure 3.36 Report Options Dialog Box

This dialog box is brought up when the user selects the create report file option in
the calculate menu. This can be used to output the results of the calculation or details
about the building. The output can be in either text form or comma separated variable
(CSV) format for exporting to spreadsheets, such as Excel TM.
The user can select the various loads to be included in the output by clicking the
select loads button. The rooms and zone whose results are to be included can be selected
by clicking the “select Zones” and “select Rooms” button.
The options section allows the user to select the type of report and the type of
output file. In the case of a summary report only the peak loads are reported. In the case
of a detailed report the loads for all 24 hours are reported..
By clicking the “write cooling loads” or “Write heating loads” check boxes the
user can select either to output the cooling load or heating load or both. The loads are
calculated once the OK button is pressed.
The additional Information dialog box allows the user to select the various
construction details of the building.
 48

3.24 Select loads dialog box

Figure 3.37 Load Options Dialog Box

This dialog box is brought up when the user clicks the select loads button in the output
report dialog box. The loads in the list-box that are checked will be included in the output
report. The above dialog box shows an example of zone loads selected.

3.25 Select Zone/Room dialog box

Figure 3.38 Zone Options Dialog Box

 49

This dialog box is brought up when the user clicks the select zone or select room button
in the output report dialog box. The dialog boxes allows the user to select the rooms or
zones which are to be included.

3.26 Additional information dialog box

Figure 3.39 Additional information Dialog Box

This dialog box is brought up when the user clicks the “Additional Information” button
on the create report dialog box. It allows the user to select the additional information
about building construction to be output in the report.
 50

3.27 Example of summary Output

Summary Report(Peak Loads)
______________________________________________________

Name Of Building: Office Building

##Cooling Load Calculations##

Coil Loads
----------
| Load |Hour | Total CLg |Sensible CLg | Latent CLg | Air Flow
| | | Coil Load | Coil Load | Coil Load |
| | | (BTU/Hr) | (BTU/Hr) | (BTU/Hr) | (CFM)
____________________________________________________________________________________
North zone 17 43828.4 38145.9 5682.5 1734.7
South Zone 17 37936.2 30552.4 7383.8 1389.9
Sum 17 81764.6 68698.3 13066.3

Room Loads
----------
| Load |Hour | RoomTot | RoomSen | RoomLat | Supply
| | | Clg.Load | Clg.Load | Clg.Load | AirFlowRate
| | | (Btu/hr) | (Btu/hr) | (Btu/hr) | (CFM)
_____________________________________________________________________________________
North zone
office no 1 17 20239.2 18488.6 1750.6 840.3
office no3 17 7150.9 5888.6 1262.3 267.6
Store 17 5299.6 4442.3 857.3 201.9
toilet 17 3926.5 3412.1 514.4 155.1
corridor 17 7077.9 5934.8 1143.1 269.7
South Zone
Office no 2 17 7034.3 5772.0 1262.3 262.3
ConferenceRoom 17 18140.3 12947.2 5193.1 588.5
Lobby 15 12885.5 12172.9 712.6 553.3
 51

3.28 Generic Library dialog box

Figure 3.40 Generic Library dialog box.

Many parts of HvacLoadExplorer utilize a library, e.g. locations, walls, roofs, etc.
Each library uses dialog boxes as shown in the Figure 3.40.

The data are displayed in a tabular format in a grid. This grid displays data from
both the standard library and the User library. The information from the standard Library
is displayed in black text and the information from the User library is displayed in red
text.
Only one row in the grid is can be selected at any instant. Hence, there should be
no confusion about the record that is selected or that has to be modified or deleted. A
status bar has been included which gives information about the currently selected record,
whether it is from the standard library or the user library. Double clicking a particular
row brings the control back to the main form, which initiated the library form.
 52

Alternatively the user can also press the ‘Select’ push button after clicking on the row of
interest
The dialog box has push buttons with captions ‘Add’, ‘Modify’ and ‘Delete’. The
‘Add’ push button will always be enabled. The ‘Modify’ and ’Delete’ push buttons will
be enabled only when the currently selected record is from the user library. This prevents
the user from modifying or deleting records that belong to the standard library.

The dialog box also includes buttons with captions ‘Search’ and ‘Show All’. The
‘Search’ button brings up a search dialog box. When records matching the search criteria
are found, they are displayed in the grid. The user can revert to displaying all the records
by clicking the ‘Show All’ push button. The ‘Show All’ push button will be enabled only
when the grid displays search results.

The user can also ‘Import’ and ‘Export’ the libraries. Clicking the ‘Export’ button
while search results are being displayed will result in exporting the matching records
from the User Library to an ASCII text file with the ‘.lib’ extension. Clicking the
‘Export’ button with all records displayed will export the entire User Library to an
ASCII text file. With this file, one or a few library items can be moved between
computers or users.

3.29 Add Layer dialog box

Figure 3.41 Add Layer dialog box.

 53

The dialog box, shown in Figure 3.41, appears when a new layer is to be added in
the layer library. It shows the layer name as well as text fields for entering the properties
of the layer. Properties include conductivity, density, thickness, specific heat and layer
name. As the values of L/K (Thickness/Conductivity) are used to calculate the effective
thermal resistance of the wall. None of those two values should be zero as a ‘division by
zero’ error will occur in the solver. This check is made in the program.

In some cases, the user may be interested in adding a purely resistive layer, e.g.
fiberglass insulation. In that case, the user may set the specific heat and density to zero,
set the conductivity to 1 and set the thickness to the desired resistance.

Clicking on ‘Ok’ adds a new layer in the library database. The initial values in the
dialog box depend on whether user has clicked on any layer in the database. Name of the
layer has to be unique in the database.

3.30 Search Help dialog box

Figure 3.42 Search Help dialog box

This search help dialog box, shown in Figure 3.42, tells about the different
options that user can have while searching the library. This dialog box comes up when
the user clicks on the ‘help’ button on the dialog box, which comes up when he clicks on
the ‘Search’ button.
 54

4.0 – Calculation of Radiant Time Series

Factors and Response Factors
The Radiant Time Series Method (RTSM) is an approximation of the heat balance
method. A heat balance simulation is required to produce the coefficients of the radiant
time series for a given zone construction. A series of 24 radiant time series factors, which
completely describes the zone response to the steady periodic input, can be generated
using HvacLoadExplorer. Likewise HvacLoadExplorer can also calculate periodic
response factors used for computing conduction heat gains with the RTSM.

In order to use the heat balance method to generate the radiant time series, a zone
description consisting of geometric and construction information is needed. All surfaces
are represented as ‘partition’ heat storage surfaces that do not interact with the outside
environment. It is not necessary to describe weather conditions, internal heat gains
(people, lights, equipment), infiltration, zone axis orientation, or supply air temperatures.
But, it is necessary to describe all surfaces, including windows, and the room air
temperature must be set to a fixed value for all 24 hours.

If only periodic response factors are needed, only the minimal number of surfaces
must be described. (HvacLoadExplorer needs at least one wall type surface and a floor
type surface in a room to be able to complete the calculation successfully.

Once the above information has been entered, ‘Execute for Room’ will perform a
heat balance simulation and provide the radiant time factors and periodic response factors
as shown in Figures 4-1 and 4-2.
 55

Figure 4.1 Radiant Time Series Factors Displayed in Text Form

Figure 4.2 Radiant Time Series Factors Displayed in Graph Form

 56

Appendix 1
HVAC Load Explorer Version 1.1.0
new features
Version 1.1.0 has added several new features, summarized below. Many of these
features previously appeared in incremental releases made on the book website..

1. In order to support calculation of airflow rates for heating, it was necessary to

allow users to specify the supply air temperature for heating. This is done in the
Zone information dialog box, as shown below. The Zone Information dialog box
can be opened by double-clicking the zone icon, or by right-clicking on the zone
icon in the tree view, and choosing “Properties”.

Figure A1-1 Zone Information Dialog Box

 57

2. Calculations can now be done for all rooms in a zone. This allows the user to get
a “sub-total” of all the cooling or heating loads for the rooms in a particular zone.
This may be useful for sizing equipment that only serves a particular zone. To do
this, choose “Execute for Zone” from the Calculate menu, after selecting a
specific zone, as shown below.

Figure A1-2 Calculate Menu

3. Heat gains such as lighting, people, equipment, infiltration, and ventilation may
now be independently included or excluded from the cooling and heating load
calculations. As shown in the Light Information dialog box, two check boxes
have been added. If both boxes are checked, the program will work as before,
calculating the effect of the lighting heat gain on both the cooling and heating
load.
This feature is intended to support heating load calculations, where it is often
desirable to calculate the heating load without taking credit for heat gains due to
lights, people, and equipment.
 58

Figure A1-3 Equipment Gain Dialog Box

4. Items in the Tree View may be right-clicked; an appropriate menu will come up.
See example below.

Figure A1-4 Menu that Appears when Right-Clicking on Tree View Item

5. A feature to update all the walls with the same name to a different construction
has been added. This may be useful for cases where a user wishes to change the
 59

construction of a number of walls at once. For example, if the user has a

construction called “My House Wall” that appears in a number of rooms, and the
user wishes to increase the insulation level everywhere, this option may be used to
make the changes everywhere at once. This can be done from the construction
library dialog box that can be accessed through the wall information dialog box.

6. Free floating zones can now be included the building construction. This allows
the user to model attics, garages, crawlspaces, etc. . The free-floating room
temperature can then become a boundary condition for rooms in normal (or, for
that matter, in free-floating) zones. A common application would be attics above
conditioned rooms. In the conditioned room, the ceiling can be set to have a TIZ
boundary condition, with the other side temperature coming from the attic. In the
attic, the floor can be set to have a fixed or scheduled other side temperature
equivalent to the controlled temperature in the conditioned spaces. The
temperature of the free floating zone after the simulation can be viewed after the
simulation.

7. Output reports can be generated in either text or comma-separated-variable

format. The user can choose the types of output in the report. Specific zones and
rooms may be specified and/or specific load types may be specified. In addition,
the report can contain details of the building geometry and construction, etc. For
loads, either a comprehensive report, containing values for all 24 hours, may be
generated or a summary report containing only the peak loads may be produced.