Appendix A – Technical Specifications

Appendix A
Technical Specifications

158 www.qualitrolcorp.com
Appendix A – Technical Specifications

Appendix A – Technical Specifications

The following table lists the technical specifications for the IDM+ device.
Category Parameters Specifications
General Processor 32 bit, 400 MHz processor
9 configurable analog channels for IDM+ 3U device ,
9/18/27/36 configurable analog channels for IDM+ 6U
device.
Sampling rate 25.6 kHz at 50 Hz, 30.72 kHz at 60 Hz
Bandwidth 25 to 4600 Hz ± 0.5 dB
Operating System Monta Vista Linux with real time extensions
Status Indicators 9 LEDs (Healthy, Communication, clock sync, battery,
trigger, alarm and sensors (status))
Quality System Developed, designed, and manufactured according to
DN ISO 9001:2000.
Calibration Solid state design, no user adjustments.
Calibration check must be performed once in 5 years.
Data Storage Compact Flash for record storage 4 GB standard (8
GB/16 GB optional)
On-board Flash for firmware – 64 MB
A RAM based temporary file system is used to avoid
excessive Flash use avoiding Flash wear. The IDM+
firmware is designed to optimize the write operations
for every memory block.
Power Supply Input Range Type 1: 90 – 264 VAC (88-300 VDC), 47 –63 Hz
Type 2: 36 – 72 VDC
Maximum Load 40 VA for 3U IDM+ device and
80 VA for 6U IDM+ device
Typical Load
For 6U Device
110 VA (With UPS)
112 VA (With UPS)
Auxiliary Output DC output 12 VDC at 750 mA

159 www.qualitrolcorp.com
Appendix A – Technical Specifications

Category Parameters Specifications

Analog Inputs - Input Range Nominal (full scale) in VAC:
Voltage AC 63.5 (140)
120 (270)
240 (480)
440 (800)
Safety Rating 300 V CAT III, 150 V CAT IV
Maximum Overload 1000 VAC continuous
Input Option 1: Impedance: > 2.5 MΩ (at 63.5 V) ,> 2 MΩ (at 120 V) , >
TX_AFE 1 MΩ (at 240 V), > 0.1 MΩ (at 440 V)
16-bit resolution for voltage
Input Option 2: Impedance: > 4MΩ
HIA-AFE 24-bit resolution for voltage/current channels:
Accuracy ≤ 0.1°

Optional for The transient voltage (up to 6 kV) is detected by the TR

HIA-AFE: module with a bandwidth of 2.5 kHz to 5 MHz.
Fast Transient Sampling rates (user configurable):
Recording 20 MHz, 10 MHz, 5 MHz, 2.5 MHz, 1.25 MHz
12-bit resolution

Analog Inputs - Input Range Full scale in VDC: 12, 120, 240, 480
Voltage DC
(optional Safety Rating 300 V CAT III, 150 V CAT IV
instead of AC)
Maximum Overload 500 VDC continuous
Input Impedance >= 420 KΩ - (TX-AFE and HIA-AFE)

Analog Inputs – Input Range Nominal (full scale) in AAC: 1 (10), 2 (20), 5 (50), 10
Current (100)
Maximum Overload 200 A for 1 second, 40 A continuous
Input Impedance < 0.02 Ω
20-bit resolution for current
(To achieve a 20-bit resolution on a current channel,
two 16-bit A/D converters are used with different gain
factors to provide an effective 20-bit resolution.)
. Digital Inputs 32 (isolated into groups of 8)
Voltage range independent from 24/48 to 250 VDC

160 www.qualitrolcorp.com
Appendix A – Technical Specifications

Category Parameters Specifications

Alarm Notification 4 form A/B relay outputs (configurable - normally closed
or normally open at factory)
Relay 1 indicates system Healthy.
Relay 2, 3 are user configurable for PQ parameters.
Relay 4 is user configurable for either temperature
under/over temperature threshold.
Resistive load: 250 VAC 5 A, 110 VDC 0.5 A, 48 VDC
1.0 A
Options Time GPS (accuracy ± 300 ns between time masters)
Synchronization IRIG-B modulated and level shift (accuracy ± 2 ms
between time masters)
Time slave (synchronized through 1 PPS)
Mechanical Dimensions H x W x D: 132.5 mm 487 mm x 362.2 mm for IDM+ 3U
device
H x W x D: 265.8 mm 487 mm x 362.2 mm for IDM+ 6U
device
Weight 15 kg without battery and 15.5 kg with battery for IDM+
3U device
23 kg without any external battery and 4 kg with two
external batteries for IDM+ 6U device
Housing/Mounting Metal 19” rack mounted cabinet

Communication Ports Four Serial (of these, three are RS232 ports with male
DB-9 connectors, and one is RS485 with 1*5 pin
connector.)
Internal PSTN (V.90) modem (optional on RS232-2)
Two 100 Mb Ethernet ports with RJ45 connectors
Optional Fiber optic Ethernet (on rear port)
Differential (RS485 levels) for 1 PPS for time
synchronization
Fiber optic 1 PPS output (master)/input (slave)
Protocols TCP/IP, Modbus, IEC 60870-5, IEC 61850, GSM,
GPRS

Standard IEC 61000-4-30 Class A

Compliance IEC 61000-4-7 harmonics and inter-harmonics
IEC 61000-4-15 flicker
CBEMA, ITIC
IEEE 1159, IEEE 519

161 www.qualitrolcorp.com
Appendix A – Technical Specifications

Category Parameters Specifications

Environmental Temperature Operating: -5°C to 50°C (23°F to 122°F)
Cold start is not possible below 0°C (32°F)
Storage: -30°C to +70°C (-22°F to +158°F)
Humidity 0 to 95% non-condensing
Enclosure IP 40 according to IEC 60529

Others RoHS compliant

EMC Standards

Standards References/Test criteria

IEC 60255-22-6 / IEC 61000-4-6 Tested to IEC 61000-4-6, Tested for 10 V, 150 kHz –
Conducted Susceptibility (CS) 80 MHz
Tested on Power-line, RS232 -1, Ethernet port 1,
Analog inputs (V & I), Digital Inputs, and Relay Outputs.
Passed with : Criteria A

IEC 60255-22-4 / IEC 61000-4-4 & Tested to IEC 61000-4-4, Tested for : 4 kV,
ANSI C37.90.1.2002 Electrical fast 5KHz/100KHz/2.5KHz
transient burst test Tested on Power-line, RS232-1, Ethernet port 1, Analog
inputs (V & I), Digital Inputs, Relay outputs.
Passed with : Criteria A

IEC 60255-22-3 / IEC 61000-4-3 Tested to IEC 61000-4-3, Tested for 10 V/m, 80 MHz –
Radiated Susceptibility (RS) 1000 MHz
Tested on Complete Device
Passed with : Criteria A
EN 55011 Conducted Emission (CE) Tested to CISPR-11 Tested for 79 dB (µV) quasi-peak
and 66 dB (µV) average at 0.15 MHz to 0.5 MHz
73 dB (µV) quasi-peak and 60 dB (µV) average at 0.50
MHz to 5 MHz
73 dB (µV) quasi-peak and 60 dB (µV) average at 0.50
MHz to 30 MHz
Tested on : Complete Device
Passed & the Emission levels are within the Specified
limits of CISPR 11

162 www.qualitrolcorp.com
Appendix A – Technical Specifications

Standards References/Test criteria

EN 55011 Radiated Emission (CE) Tested to CISPR-11 Tested for 40 dB (µV/m) quasi-
peak from 30 MHz to 230 MHz
at 10 m (32.8 ft)
47 dB (µV/m) quasi-peak from 230 MHz to 1000 MHz at
10 m (32.8 ft)
Tested on : Complete Device
Passed & the Emission levels are within the Specified
limits of CISPR 11
IEC 61000-4-8 Power frequency Tested to IEC 61000-4-8 ,Tested for 30 A/m, x, y, z
magnetic field test axis
Tested on : Complete Device
Passed with : Criteria A
IEC 60255-22-1 / IEC 61000-4-12 & Tested to IEC 61000-4-12 ,Tested for 2.5 kV Common
ANSI C37.90.1.2002 Damped Mode, 1 kV Differential Mode, 1MHz
oscillatory wave disturbance tests Tested on : Power-line, Digital, Analog inputs( V ),
Relay
Passed with : Criteria A
IEC 61000-4-12 Ring wave test Tested to IEC 61000-4-12, Tested for Level 3,+/- 2 kV
Common Mode, 1 kV Differential Mode, 100 KHz
Tested on Power-line, Digital, Analog inputs (V), Relay
Passed with : Criteria A
IEC 61000-4-5 Surge test Tested to IEC 61000-4-5 ,Tested for Class 4, I/O 4 KV
Common Mode, 2 KV Differential Mode
Tested on Power-line, Digital, Analog inputs (V), Relay
Passed with : Criteria A

ENV 50204 Immunity to EMI from Tested to ENV 50204, Tested for level 3, 10 V/m, @900
digital radio telephones MHz +/- 5 MHz, @1890 MHz +/- 10 MHz keyed at
frequency 200 Hz +/- 1%, 50% duty cycle [2.5 ms ON
2.5 ms OFF].
Tested on Complete Device
Passed with : Criteria A
IEC 60255-5 Clause 6 Dielectric test Tested to 2.5 kV for 1 minute, Tested for 2.5 kV for
ANSI IEEE C37.90 – 1989 SWC Power-port, Analog inputs (V & I), Digital inputs, Relay,
dielectric tests and 1 kV for isolated communication ports (RS232 &
RS485).
No flashover or breakdown occurred.

163 www.qualitrolcorp.com
Appendix A – Technical Specifications

Standards References/Test criteria

IEC 60255-5 Clause 7 Insulation test Tested to applied 500 VDC with respect to Earth.
Tested on Power port, Analog inputs (V & I), Digital
inputs & Relay.
The impedance was greater than 100Mohms.

IEC 60255-5 Clause 8 Impulse voltage Tested to +/-5 kV, 0.5 J.

test Tested on: Power-line, digital, Analog inputs (V & I) &
Relay.
No flashover or breakdown occurred.
IEC 61000-4-11 Supply Voltage Dips Tested to Dips-Class-3,Interruptions-Class-3
and Interruptions Tested on Power-port.
Passed with : Dips - Criteria A
Interruptions - Criteria B
IEC 60255-22-2 / IEC 61000-4-2 Tested to IEC 61000-4-2,Tested for : 8 kV contact, 15
Electro static discharge tests kV air
Tested on Enclosure, all accessible I/O lines and ports.
Passed with : Criteria A
IEC 60255-6/EN60255-6 Supply Tested for PSU Tested for DC range 80 VDC to
voltage limit test 300VDC

IEC 60068-2-1/EN60068-2-1 Cold Tested for Cold Storage -45˚C (49˚F) for 96 hours
tests Cold Operating: -5˚C (23˚F) for 16 hours
Tested on Complete Device
IEC 60068-2-6 Vibration tests Tested for 2g Acceleration, Frequency is 10- 150 HZ, 20
sweep cycles in each of three mutually perpendicular
planes (x, y, and z).
Tested on Complete Device
IEC 60068-2 Cyclic Temperature Test Tested for Cyclic Temperature test for 5 cycles. Each
cycle has 3 hours for 70 degrees & 3 hours for -5
degree in Power off Condition
Tested on Complete Device

164 www.qualitrolcorp.com
Appendix A – Technical Specifications

IEC 61000-4-30 Class A

The following table summarizes the IDM+ accuracy and range specification of IEC 61000-4-
30 Class A parameters. The IDM+ is specified for Udin = 230V, 50/60 Hz.
Parameter Accuracy Measuring Accuracy
Specified over Range
Range
Frequency 42.5 Hz ~ 57.5 42.5 Hz ~ 57.5 +/- 0.01 Hz of injected
Hz, Hz,
51 Hz ~ 69 Hz 51 Hz ~ 69 Hz
Voltage RMS 10%~150% of 10%~200% Udin +/- 0.1% of Udin
Udin.
Flicker short term 0.2~10.0 Pst 0~20 Pst 5% of Measured Value / applied
(10 min)-Pst input
Supply Voltage Dips N/A N/A ±0.2% of Udin.
and Swells
Voltage interruptions N/A N/A ±0.2% of Udin.

Voltage Unbalance 1 – 5% 0 – 100% If unbalance is in the range 1 to

5% = +/-0.15%

Harmonics (up to 10% to 200% of 200% of Class 3 Um >= 1% Unom Æ 5% of Um

50th order) Class 3 IEC of IEC 61000-2- Um < 1% Unom Æ .05% Unom
61000-2-4 4 ( Max allowed THD = 20% )
Interharmonics (up to 10% to 200% of 200% of Class 3 Um >= 1% Unom Æ 5% of Um
50th order) Class 3 IEC of IEC 61000-2-4 Um < 1% Unom Æ0.05% Unom
61000-2-4 ( Max allowed THD = 20% )

Signaling Voltages 0% to 15% of 0% ~ 15% Udin 1% and 3% of UdinÆ ±0.15% of

Udin [below 3 Udin
kHz] 3% and 15% of UdinÆ ±5 % of
the measured value

Supply Voltage Under 10% ~ 150% of N/A +/- 0.1% of Udin

and Over deviation Udin.

Note Udin = Nominal voltage

Um = Measured Voltage
Unom = Nominal voltage

165 www.qualitrolcorp.com