Conductivity Brix Transmitter-
NCBTM-59
Product Descriptions:
Narendra Electronics and Technology here introduces the brix
Transmitter .Our device can efficiently measure the brix The
Industries that require to measure the sugar content .It can be used
in sugar mills or the food industries that require a sucrose
measurement can rely on our product like in candy making ,cookie
manufacturing ,beverages production etc . Our Brix Transmitter
are working successfully in many sugar factory since last two years.
Introduction:
This is Microprocessor Based Online Conductivity Transmitter for Brix
Reference Measurement System. The Instrument Measure Conductivity
of Brix in Batch/Continuous Vacuum Pans etc., our transmitter has an
efficient working in B batch pan B continuous pan and C batch pan and
C continuous pan and A Batch pan etc. It Have Two Relay control o/p
for electrode Auto Cleaning. In the parameter of auto cleaning user can
be set time for auto cleaning interval (As time In minutes, Like 30/60
etc.). During The auto cleaning instrument hold last o/p value up to
cleaning process complete. Its fundamental principle is conductivity. It
is used to measure messecute’s conductivity. Conductivity is inversely
proportional to brix (if conductivity increases then brix decreases and
vice – versa). Here the constant is K its value is dependent upon two
factor i.e temperature and Conductivity.
BRIX = K *1 /CONDUCTIVITY
The Instrument is Field Programmable and user friendly. The
Instrument Have One computer communication Port (Rs485). It also
has an Optional feature of WIFI connection Along with one Analog
Isolated of 4-20mA.
How To Use ?
Step1: Switch the power on
Step2: Select The Parameter Temperature and set the value of
temperature as that is found near the sensor.
Step3: set the value of Action parameter As 0 value.
Step4 : Now Select the output parameter , Here The user can decide
whether they want output in Brix Or Conductivity. It can be Done in the
Following Way:
0 value for conductivity
1 Value for Brix
Step5: Auto Cleaning Mode can be used in two following ways
During This Mode if we measure the liquid Sugar Then Water
connection should be disconnected.
Or If we measure Of Brix in Pan there is a need of hot water
connection for Sensor.
Note:
Set the value as 10 in the parameter of cyl_in_out
Set the value(minutes) in the parameter of Auto Cleaning time so
that after the given time it will auto clean.
Step6: Communication Parameter Can be Selected from Any of the One
from Following.
Value 0 for Disable Communication.
Value 1 for Modbus Commination(RS485) ,If this value is set Then
we have to set Slave ID Parameter value from 1-255.
Configuration: Press PRG key for 5Seconds Display Parameter
Action. Now user can select Parameter that they want to modify by use Of
Up/Dn key , Then press Enter Key after That use Up/Dn key to modify
further And then Press Enter Key to Store. Now Select Next parameter
and apply same . If want Exit from Configuration Mode then select Exit by
Use UP/DN key and Press E key Now System in Run Mode.
Calibration:
Press PRG Key for 5 seconds and display Action parameter ,Now use UP/DN
Key To select Auto Tune Parameter . After that press and hold PRG key for
1 second now press E key and now leaves both keys, NOW the transmitter will
display “Calibration On>>”Wait for up to calibration has to be done. After
calibration complete, it will Show value of Brix.
Applications:
Batch Pan Automation.
Continuous Pan Automation.
Molasses Conditioner Automation
Liquid Sugar syrup Brix measurement etc.
Parameters & Descriptions:
Action : 0= Forward, 1= Revers Action ( On Display & Output
2k=100% (20mA) & 200E = 0% (4mA) )
Auto Cleaning Time : For Electrode Auto Cleaning Time set (0-
60000 Minutes)
Auto Tune: For Auto calibration
Temperature: set the value of temperature
Nos.Of In/Out CyL : In this parameter User can be set value of
pneumatic cylinder In/Out Numbers(During Auto Cleaning).
Output: Here The user can decide whether they want output in
Brix Or Conductivity.(1/0)
Modbus Comm. Id. :
Note: During Auto Cleaning hot water not apply when you are using in
syrup brix sensing.
Modbus Comm. Id. : set Slave ID Parameter value from 1-255.
An Optional feature of WIFI connection.
SPESCIFICATION
Power Supply : 220V AC, @50HZ
Display : Blue LCD/ Backlit LED
Enclosure : ABS plastic 96x194x223 mm (HxWxD )
Overall size : 96x194x223 mm (HxWxD )
Panel cutout : 184X92mm(WxH)
Output : 4-20 mA Isolated (Conductivity/Brix)
Accuracy : 99.8%
Input : S.S Conductivity Electrode
Auto Cleaning Timer :0- 60000 Minutes.
2Nos Relay : Both Relay use for Auto Cleaning
Relay RL1 : For Water on solenoid value
Relay Rl2 : For cylinder In/out solenoid value
Terminal Details
L : Phase of 220v AC @50Hz
N : Neutral
E : Earth
Sensor Input : S1, S2 from electrode unit
C1, NO1 : Water on solenoid value
C2 , NO2 : In/out solenoid value
+ /- : o/p 4-20 mA(Isolated)
o/p 4-20 MA
S2
S1
C2,
NO2
C1,NO1
NO1
Auto Cleaning Type Sensor
