ORDER NO.

CRT4513
GM-3400T/XJUC

BRIDGEABLE TWO-CHANNEL POWER AMPLIFIER

GM-3400T /XJUC

GM-3400T/XJEW5
GM-3400T/XJES

For details, refer to "Important Check Points for Good Servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2009
K-ZZZ. DEC. 2009 Printed in Japan
 1 2 3 4

SAFETY INFORMATION
CAUTION
A This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65

B
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:

GM-3400T/XJUC
2
1 2 3 4
 5 6 7 8

[Important Check Points for Good Servicing]

In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.

3 Make sure the soldering of repaired locations is properly performed. B

When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C

7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.

a Safe environment should be secured during servicing. D

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws

To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

GM-3400T/XJUC
5 6 7 8
3
 1 2 3 4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS......................................................................................................................... 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 7
2. SPECIFICATIONS ............................................................................................................................................ 8
2.1 SPECIFICATIONS...................................................................................................................................... 8
2.2 PANEL FACILITIES .................................................................................................................................. 10
2.3 CONNECTION DIAGRAM ....................................................................................................................... 11
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 12
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 12
3.2 JIGS LIST ................................................................................................................................................ 12
4. BLOCK DIAGRAM.......................................................................................................................................... 12
5. DIAGNOSIS.................................................................................................................................................... 13
5.1 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 13
B 6. SERVICE MODE ............................................................................................................................................ 13
7. DISASSEMBLY............................................................................................................................................... 14
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 15
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 16
9.1 PACKING ................................................................................................................................................. 16
9.2 EXTERIOR............................................................................................................................................... 18
10. SCHEMATIC DIAGRAM ............................................................................................................................... 20
10.1 AMP UNIT(GUIDE PAGE)...................................................................................................................... 20
11. PCB CONNECTION DIAGRAM ................................................................................................................... 26
11.1 AMP UNIT .............................................................................................................................................. 26
12. ELECTRICAL PARTS LIST .......................................................................................................................... 30
C

GM-3400T/XJUC
4
1 2 3 4
 5 6 7 8

1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A

1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic
induction.
3. When you tighten the screws No. 1 to 10, tightly hold a transistor or a diode to be fixed to prevent the part from
turning by the force of tightening the screw.
(If the part turned, a stress will be applied to the solder and may cause a failure such as a solder crack.)

4. When you replace a part fixed to the heatsink (Q515, Q516, Q517,Q518, Q519, Q520, Q803, Q804, D821 and D822),
adjust the position of the part according to the following.

Put the Amp Unit on blocks.

D

GM-3400T/XJUC
5 6 7 8
5
 1 2 3 4

Put a paper between the block and the Amp Unit,

and outline transistors and diodes.
A Put a part to replace in the outline.

Align the bottom of a transistor or a diode with the

top of the PC board, and solder it.
Apply grease, GEM1057 to the back of the part.

5. Silk-prints of "L" and "R" on the Amp Unit are printed wrongly each other. ("L" should be "R", and "R" should be "L".)
D

GM-3400T/XJUC
6
1 2 3 4
 5 6 7 8

1.2 NOTES ON SOLDERING

For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
A
accompanied by reworking of soldering.

Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).

The following lead-free solders are available as service parts:

Parts numbers of lead-free solder: B
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

GM-3400T/XJUC
5 6 7 8
7
 1 2 3 4

2. SPECIFICATIONS
2.1 SPECIFICATIONS
A

GM-3400T/XJUC

Power source...........................14.4 V DC (10.8 V to 15.1 V Low pass filter:

allowable) Cut off frequency ......... 80 Hz
Grounding system.................Negative type Cut off slope .................. –12 dB/oct
Current consumption .......... 15 A (at continuous power, Gain control:
4 ohm) RCA ................................. 200 mV to 6.5 V
Average current drawn........ 4 A (4 ohm for two channels) Speaker ........................... 0.8 V to 26 V
7.8 A (4 ohm for one channel) Maximum input level / impedance:
B
Backup current ...................... 0.1 mA or less RCA .................................. 6.5 V / 22 k ohm
Fuse ......................................... 25 A × 1 Speaker ............................ 26 V / 90 k ohm
Dimensions (W × H × D) ... 263 mm × 61 mm × 206
mm(10-3/8 in. × 2-3/8 in. × CEA2006 Specifications
8-1/8 in.)
Weight ..................................... 2 kg (4.4 lbs)
(Leads for wiring not in-
cluded)
Maximum power output ...... 120 W × 2 (4 ohm)
/ 350 W × 1 (4 ohm)
Continuous power output ..60 W × 2 (at 14.4 V, 4 ohm
Power output .......................... 60 W RMS × 2 Channels (at
, 20 Hz to 20 kHz 0.2% THD)
C 14.4 V, 4 ohm and 1 % THD
175 W × 1 (at 14.4 V, 4 ohm
+N)
, 20 Hz to 20 kHz 0.8% THD)
175 W RMS × 1 Channels
85 W × 2 (at 14.4 V, 2 ohm
(at 14.4 V, 4 ohm BRIDGE and
, 20 Hz to 20 kHz 0.8% THD)
1 % THD+N)
Load impedance ................... 4 ohm (2 ohm to 8 ohm allowable)
85 W RMS × 2 Channels (at
(Bridge connection: 4 ohm to 8
14.4 V, 2 ohm and 1 % THD
ohm allowable)
+N)
Frequency response............ 10 Hz to 50 kHz (+0 dB, –1
S/N ratio .................................. 75 dBA (reference: 1 W into
dB)
4 ohm)
Signal-to-noise ratio............ 95 dB (IHF-A network)
Distortion ................................ 0.01 % (10 W, 1 kHz)
D
Separation .............................. 70 dB (1 kHz) Notes
• Specifications and the design are subject to
modifications without notice due to improve-
ments.
• The average current drawn is nearly the maxi-
mum current drawn by this unit when an
audio signal is input. Use this value when
working out total current drawn by multiple
power amplifiers.

GM-3400T/XJUC
8
1 2 3 4
 5 6 7 8

GM-3400T/XJEW5, GM-3400T/XJES A

Power source..........................14.4 V DC (10.8 V to 15.1 V Notes

allowable)
Grounding system.................Negative type • Specifications and the design are subject to
Current consumption .......... 15 A (at continuous power, modifications without notice due to improve-
4 ohm) ments.
Average current drawn........ 4 A (4 ohm for two channels) • The average current drawn is nearly the maxi-
7.8 A (4 ohm for one channel)
Backup current ....................... 0.1 mA or less
mum current drawn by this unit when an
Fuse ......................................... 25 A × 1 audio signal is input. Use this value when
Dimensions (W × H × D) ... 263 mm × 61 mm × 206 working out total current drawn by multiple
mm B
power amplifiers.
Weight ..................................... 2 kg (Leads forwiring not in-
cluded)
Maximum power output ....... 120 W × 2 (4 ohm)
/ 350 W × 1(4 ohm)
Continuous power output ... 60 W × 2 (at 14.4 V, 4 ohm)
, 20 Hz to 20 kHz 0.2% THD)
175 W × 1 (at 14.4 V, 4 ohm)
, 20 Hz to 20 kHz 0.8% THD)
85 W × 2 (at 14.4 V, 2 ohm)
, 20 Hz to 20 kHz 0.8% THD)
Load impedance ................... 4 ohm (2 ohm to 8 ohm allowable)
(Bridge connection: 4 ohm to 8 C
ohm allowable)
Frequency response............. 10 Hz to 50 kHz (+0 dB, –1
dB)
Signal-to-noise ratio............ 95 dB (IEC-A network)
Distortion ................................ 0.01 % (10 W, 1 kHz)
Separation ............................. 70 dB (1 kHz)
Low pass filter:
Cut off frequency ......... 80 Hz
Cut off slope .................. –12 dB/oct
Gain control:
RCA ................................ 200 mV to 6.5 V
Speaker .......................... 0.8 V to 26 V D

Maximum input level / impedance:

RCA ................................ 6.5 V / 22 k ohm
Speaker .......................... 26 V / 90 k ohm

GM-3400T/XJUC
5 6 7 8
9
 1 2 3 4

2.2 PANEL FACILITIES

What ’s what 3 LPF (low-pass filter) switch

Switch the settings based on the connected
Front side
speaker.
• When the Subwoofer is connected:
Select ON. This eliminates high range
frequency and outputs low range fre-
quency.
• When the full range speaker is con-
nected:
Rear side Select OFF. OFF outputs the entire fre-
B
quency range.

To adjust the switch, use a flathead screwdri-

ver if needed.

1 Power indicator
C
The power indicator lights up to indicate
power ON.

2 GAIN (gain) control

If output remains low, even when the car
stereo volume is turned up, turn controls to
lower level. If distortion occurs when the car
stereo volume is turned up, turn these con-
trols to higher level.
• For use with an RCA equipped car stereo
D
(standard output of 500 mV), set to the
NORMAL position. For use with an RCA
equipped Pioneer car stereo, with max.
output of 4 V or more, adjust level to
match that of the car stereo output.
• If you hear too much noise when using
the speaker input terminals, turn the
gain control to higher level.

GM-3400T/XJUC
10
1 2 3 4
 5 6 7 8

2.3 CONNECTION DIAGRAM

A
Connection diagram Connect male terminal of this wire to the sys-
tem remote control terminal of the car stereo
(SYSTEM REMOTE CONTROL ). The female
terminal can be connected to the auto-anten-
na relay control terminal. If the car stereo
lacks a system remote control terminal, con-
nect the male terminal to the power terminal
via the ignition switch.
9 Speaker output terminals
Please see the following section for speaker
B
connection instructions. Refer to Connections
when using the speaker input wire.
a Fuse (25 A) × 1
b Fuse (30 A) × 2
c Grommet
d Rear side
e Front side

1 Special red battery wire

RD-223 (sold separately)
After completing all other amplifier connec-
tions, finally connect the battery wire terminal
of the amplifier to the positive ( ) battery
terminal.
2 Ground wire (Black)
D
RD-223 (sold separately)
Connect to metal body or chassis.
3 Car stereo with RCA output jacks (sold sepa-
rately)
4 External output
5 Connecting wire with RCA pin plugs (sold se-
parately)
6 Speaker input terminal
7 RCA input jack
8 System remote control wire (sold separately)
E

GM-3400T/XJUC
5 6 7 8
11
 1 2 3 4

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
A

To keep the product quality after servicing, please confirm following check points.

No. Procedures Item to be confirmed

1 Confirm whether the customer complain has The customer complain must not be
been solved. reappeared.
Audio and operations must be normal.
2 Check the output sound. Audio and operations must be normal.
3 Appearance check No scratches or dirt on its appearance after
B receiving it for service.

See the table below for the items to be checked regarding audio:

Item to be checked regarding audio

Distortion
Noise
Volume too low
Volume too high
Volume fluctuating
C
Sound interrupted

3.2 JIGS LIST

D
- Lubricants and Glues List
Name Grease No. Remarks
Grease GEM1057 Applying to Heatsink
Bond GYL1006 Applying to choke coil, resistor and capacitor

4. BLOCK DIAGRAM
There is not information to be shown in this chapter.

GM-3400T/XJUC
12
1 2 3 4
 5 6 7 8

5. DIAGNOSIS
5.1 CONNECTOR FUNCTION DESCRIPTION
A

6. SERVICE MODE D
There is not information to be shown in this chapter.

GM-3400T/XJUC
5 6 7 8
13
 1 2 3 4

7. DISASSEMBLY
- Removing the Case (Fig.1)
A

1 1

1 Remove the four screws

and then remove the Case.

1 1

Fig.1

Case

- Removing the Amp Unit (Fig.2)

1 1
C

1 Remove the two screws.

3
2
3
2 Remove the ten screws.
2 3 2
Remove the eight screws 2 2
3
and then remove the Amp Unit. 3 3
2 2
2 3 2
When you tighten the screws indicated
D by Arrow 2, tightly hold a transistor or 3
a diode to be fixed to prevent the part 2
3
from turning by the force of tightening
the screw. Fig.2
(If the part turned, a stress will be
applied to the solder and may cause a
failure such as a solder crack.) Amp Unit

GM-3400T/XJUC
14
1 2 3 4
 5 6 7 8

Bonding Position

1 GYL1006

1
B

1 1

C
1

1 1 1

8. EACH SETTING AND ADJUSTMENT

There is not information to be shown in this chapter.

GM-3400T/XJUC
5 6 7 8
15
 1 2 3 4

9. EXPLODED VIEWS AND PARTS LIST

NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
"
Screw adjacent to mark on the product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
9.1 PACKING

GM-3400T/XJUC
16
1 2 3 4
 5 6 7 8

(1) PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Cushion CZH6698 7 Contain Box CZH6703

* 2 Polyethylene Bag CEG1250 8 •••••
A
* 3 Warranty Card See Contrast table(2) 9 Owner's Manual See Contrast table(2)
4 Cord Assy CZD5517 10 Screw Assy CEA5330
* 5 Polyethylene Bag See Contrast table(2)
11 Screw BYC40P180FTB
6 Unit Box See Contrast table(2) * 12 Polyethyene Seet CNM4338

(2) CONTRAST TABLE

GM-3400T/XJUC, GM-3400T/XJEW5 and GM-3400T/XJES are constructed the same except for the following:
Mark No. Description GM-3400T/XJUC GM-3400T/XJEW5 GM-3400T/XJES
* 3 Warranty Card CRY1276 CRY1279 Not used
B
* 5 Polyethylene Bag CZE2992 CZE2991 CZE2991
6 Unit Box CZH6702 CZH6700 CZH6704
7 Contain Box CZH6703 CZH6701 CZH6705
9 Owner's Manual CZR5552 CZR5551 CZR5553

Owner's Manual,Installation Manual

Part No. Language

CZR5551 English, Spanish(Espanol), German, French, Italian, Dutch, Russian

CZR5552 English, French, Spanish(Espanol)

CZR5553 English, Spanish(Espanol), Portuguese(B), Arabic C

GM-3400T/XJUC
5 6 7 8
17
 1 2 3 4

9.2 EXTERIOR

GM-3400T/XJUC
18
1 2 3 4
 5 6 7 8

(1) EXTERIOR SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

> 1 Fuse(25 A) CEK1329 9 Panel F (2CH) CZN8458

2 Screw PBH26P120FTC 10 Panel R (2CH) CZN8459
A
3 Screw BBZ30P080FTB
4 Screw BBZ30P080FTC 11 Amp Unit See Contrast table (2)
5 Screw BBZ30P080FTC 12 Holder CZN8430
13 Screw PPZ30P100FNN
6 Screw BSZ30P060FTB 14 Screw PPZ30P100FTB
7 Screw PPZ30P100FTB 15 Case Unit See Contrast table (2)
8 Chassis (Botom) CZN8457

(2) CONTRAST TABLE

GM-3400T/XJUC, GM-3400T/XJEW5 and GM-3400T/XJES are constructed the same except for the following:
B
Mark No. Description GM-3400T/XJUC GM-3400T/XJEW5 GM-3400T/XJES
11 Amp Unit CZW5581 CZW5581 CZW5582
15 Case Unit CZX6655 CZX6654 CZX6654

GM-3400T/XJUC
5 6 7 8
19
 1 2 3 4

10. SCHEMATIC DIAGRAM

10.1 AMP UNIT(GUIDE PAGE)
A Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".

A-a A-b
Large size
SCH diagram
A-a
BUFFER/ISO.AMP LPF GAIN
0 dB / 0 dB 0 dB -31.5 dB ~

TP48

TP49

TP56
A-a A-b Guide page

0.25%
R11110K

C10747P
C123
Detailed page

1SS355
A-a A-b

D109
NM

BOUTPUT

B+INPUT
B-INPUT
B

V+
OFF
8 7 6 5

0.25%

0.25%

0.25%
TP44
TP45
TP46
TP47

C103
1SS355

1SS355

1SS355
R10910K

R10710K

R10510K
47P
D101

D105

D111
IC101NJM4565M-D

TP60
RCA INPUT

1 2 3 4

AOUTPUT
C113

A+INPUT
JA101

A-INPUT

V-

TP57
CKB1068-B NM R309
C124
C111 R113 NM
Lch R119 470 2.2K

C812

0.033
1/4W NM
10/25 C301
Rch

1SS355

1SS355
R120 470 LPF
C101

R103

D103

D107

TP50

TP51
470P

22K

R311
C114 1/4W

56
0.039
NM R305 R307

R313

130K
68K 68K LPF OFF MI

A_OUT
A_+IN

A_-IN
C303

0.022
C115 S301
R121 R125 R831 C105

V-
NM
00221461
SP LEVEL INPUT

51K NM NM 4 3 2 1
10/25
1/4W
JA103 C117 R123 R127 L802 NM R101 NM
IC301 NJM4558MD
CKM1463-A VR301

TP58
5 6 7 8

B_OUT
51K NM 10K

C304

V+
L+

0.022

B_+IN
4 3 2 1

10/25 C106 0.0047

B_-IN
C119

NM

1/4W
R+
KN802

R312
L-
R306 R308

R314

130K
R-
NM

C811

0.033
68K 68K
C302 R310
10K

0.25%
C116
C108 47P

1SS355
R122 R126

D110
LPF 2.2K
51K NM 0.039
R112

10/25

TP52

TP53
1/4W
C118 R124 R128

TP59

TP61
TP40
TP41
TP42
TP43

51K NM
10/25
1/4W
C125 OFF
C BOUTPUT

B+INPUT
NM

B-INPUT
V+
10K

R108 10K
0.25%

0.25%
1SS355

1SS355
D102

D106

C104

47P

10K

8 7 6 5
0.25%

1SS355
R110

D112
IC102 NJM4565M-D

1 2 3 4
VD VH 15 V
R106

AOUTPUT

A+INPUT
A-INPUT

V-
C126 1W +27.8 V +28.0 V +15.1 V
C112 R114
NM OUTPUT -27.8 V -27.9 V -15.2 V
NM
10/25
1SS355

1SS355
C102

R104

D104

D108
470P

22K

TP54

TP55
TP37

TP36

TP38

+15V
+VD
R827
C832
NM

10 1/2W C830
220/35

C831
D
C833
NM
TP34

R828 220/35

10 1/2W
TP39

+VH
-VD

*JW122

*JW123
Q821
TP32

KTC9014
ABCD R825 *L803
EC
TP30

TP29

NM
BL02RN1R3N1A
FML-22S

KTC3875S

B
D821

E1
Q823
R835

R829

1/2W
3.3K
R832

1/4W
100

E2
NM1/2W

NM1/2W

D
R833

3.9K

R807
R836

R838

G C2
Q803
NM 1/2W

S 120
FKV550N
KTC9014
ABCD

1/2W Vcc
Q825

R837

R839

C822

R820

R809

1/2W
0.001
1/2W NM

NM

22

OPC
R813
MTZJ16B

27K
3300/35
C828

D805

C826

C824

KTA1504S
47/16

22/25

10:5 Ref
105

OYG
0.0047

Q801
R834

C805

R805

R803
3.3K

4.7K

3.3K
R821

C820
1/2W

NM

T801
22

2IN-

C810 R812 2IN+

3300/16 11K
TP27

105
KTA1504S
0.0047
R823

R822

C821

C806
1/2W

1/2W

E
NM

NM

OYG
Q802
R806

R804
22
MTZJ16B

4.7K

3.3K
3300/35
C829

D806

C827

C825
47/16

22/25

105

R824

C823

R810
1/2W

1/2W
0.001
NM

22

R808
S
G 120
Q804
1/2W R711 TH7
KTC3875S

FKV550N D TP26
R830

1/2W
3.3K

Q824

100
47
FML-22R
D822

BL02RN1R3N1A
TP28

B
-15V *L804
R826
TP31

EC NM
Q822 -VH *JW124
TP33

KTC9015
TP35

ABC *JW126
TP10
TP6
TP7
TP8
TP9

MODEL L803 L804 JW122 JW123 JW124 JW126

F GM-3400T/XJUC
GM-3400T/XJEW5

GM-3400T/XJES

A
GM-3400T/XJUC
20
1 2 3 4
 H
S301
221461

7.9 V
LPF

8.0 V
LPF
TP61 TP60

OFF

OFF

11K
R812
LPF
TP27 R813

TP26
27K

2.2K
2.2K

R310
R309

OFF

15 V

-15.2 V
+15.1 V

100
10K
VR301
R312 R311

Ref
Vcc

2IN-
E2
E1

C2
56

2IN+
OPC

470
MIN
GAIN
56

R711 TH701
16 15 14 13 12 11 10 9

C807
R815
R709 R708

NM
R707
IC801KIA494AF

Q714
2.2K 22K

MAX
Q712

47K
1 2 3 4 5 6 7 8
DTA124EKA

2SA1037AKR
220/6.3
D708 R706

C1

CT
RT

1IN-
DTC

1IN+
GND
1SS133 NM

-31.5 dB ~ -2.2 dB

FEEDBACK
R710 D709

10K
10K

R302
R301
-9.3 dB
1SS133
3.9K
5

5
TP67 TP66

NM

47
C801
R801
R734

R717
R814
C712 Q302 Q301

R802

NM
C711 2SC2412K 2SC2412K

15K

1K
0.001
D707 NM R R

10K
10K

R502
R501
NM
HZS3A2TD-E
C502 C501

R
Q713
TH702 R715 R716

2SC2412K
33P 33P
220 1K A_OUT V+

1
8
10K

IC501
R732 A_-IN B_OUT

2
7

22K
10K

R712
R714
2.7K C506
C706 A_+IN B_-IN

3
6
68P
0.22

R733
V- B_+IN

4
5
NJM2068MD
R713

1/4W
100
330K

68P

C504
C505
C503

100/10
100/10
D706 R721 R720

1SS133 NM R504 R503

4.7K
1/2W 270
C708 270

0.01

68P
22K
68P
22K

2012

C508
R506
C507
R505
2012

D705
NHSB046AT
BLUE LED
R723

R
Q705
47K

2SC2412K
C707 R722 R731 C511 C509
C512 C510
100 6.8K 10P 10P

6
6

10P 10P
22/25

R508 R510 R512 R514 R513 R511 R509 R507

560 15K 15K 560 560 15K 15K 560
1/4W 1/4W 1/4W 1/4W

identical designation.
C704
C514 C516 C515 C513

NM NM NM NM NM

R516 R518 R517 R515

TP68

TP69
47K 47K 47K 47K
C703

D710

1SS133
100/16

10P
10P
10P
10P

C518
C520
C519
C517

Q703 C523

TP24
C522
KN2907AS D711 C524 C521
0.22 0.22 0.22 0.22
1SS133
R520 R522 R524 R526 R528 R527 R525 R523 R521 R519

2.2K

the importance of the safety factor of the part.

R705
120 1.1K 4.7K 2.2K 120 120 2.2K 4.7K 1.1K 120
Q512 Q514 Q513 Q511
1/4W 1/4W 1/4W 1/4W
A-b

2SA1038S 2SC2389S 2SC2389S 2SA1038S

Therefore, when replacing, be sure to use parts of

Q516 Q515
Q702 Q709 TP73 TP72 TP71 TP70

4.7K
R704
2SC2412K 2SA1037AK KTC3114A KTC3114A

The > mark found on some component parts indicates

R D702 R702 R724 R C526 C525

1SS133 7.5K 22K 0.001

0.001
22
22

GM-3400T/XJUC
3216
3216

22
22

TP20
R531
R529

3216
3216

R530
R532

C531 R535 R533 C527

C528 R534 R536 C532
NM 47K 47K NM
NM 47K 47K NM TP75 TP74
C709 TP79 TP78
NM
C533

R703
NM
C529

NM
NM

C530
C534

0.01
2.2K
R538 R540 R539 R537

7
7

1/4W Q711

330

NOTE :
R725
2SC2412K 0.1 0.1 0.1 0.1 Q517
Q518 Q520 Q519

D701
R R728 R726 2W 2W 2W 2W 2SD2439
2SD2439 2SB1588 2SB1588

MTZJ7.5B
C702 0.001
12K 33K OP OP OP OP
Q710
R54247K
R54147K

2SC2412K
R

2.2K
1/4W
R701
D502 R544 R543 D501
C701 NM TP81 TP77
MA111 560K 560K
MA111
C536 C535
R730

NM : No Mount
NM NM
16K
Q522 Q521

2.2K
R727
KTC3911S KTC3911S

discrete resistors.
6.8K
R729
GL GL

discrete capacitors.
TP19

D804 C710
TP17
1A4-E

CZK2969-A-T
R546 R545

KN801
TP1 220/6.3
D803

Symbol indicates a resistor.

TP2 47K 47K

Symbol indicates a capacitor.

TP18
TP3 1A4-E
R548 C538 C537 R547
are printed wrongly each other.

TP4
C802
TP5 10 0.033 0.033 10
1/4W 1/4W
0.01
2012 C5400.001 C5390.001
+29 dB

C542 NM C541 NM
3216 3216 TP85
A
Silk-prints of "L" and "R" on the Amp Unit

TP97 TP84
("L" should be "R", and "R" should be "L".)

TP96 TP83
TP95 TP82
C803 TP94

L801

36uH
TP93
TP92
TP91
TP90
TP89
TP88
TP87
TP86

NM 3216 C544 NM C543 NM

No differentiation is made between chip resistors and

K000225700
C804
8

No differentiation is made between chip capacitors and

8
TP16
0.22 TP11 2 1 2 1 JA501
TP12
JA502
CKE1057-A CKE1057-A
L-

R-
L+

R+

TP13
SP OUTPUT

TP14
AMP UNIT

3 2 1 TP15

+B

REM
GND
CND2458-A

CND2458-A
JA805

JA804
FUSE (25A)

CKE1055-A
JA801
>

A
21
E
A

D
C

F
B
 4 3 2 1
22
GM-3400T/XJUC
K
301

R312 R311
56
MIN
AIN

56
NM
R707

A-b
MAX

Q712
DTA124EKA
D708 R706 F
1SS133 NM
B ~ -2.2 dB

D709
10K
10K

R302
R301
-9.3 dB

1SS133
TP67 TP66
NM
R734

C712 Q302 Q301

2SC2412K 2SC2412K
NM R R
10K
10K

R502
R501

C502 C501
33P 33P
A_OUT V+
1
8

IC501

A_-IN B_OUT
2
7

C506
A_+IN B_-IN
3
6

68P
V- B_+IN
4
5
NJM2068MD
68P

C504
C505
C503

100/10
100/10

E
R504 R503
270
270
68P
22K
68P
22K

2012

C508
R506
C507
R505
2012

C511 C509
C512 C510
10P 10P
10P 10P
R508 R510 R512 R514 R513 R511 R509 R507
560 15K 15K 560 560 15K 15K 560
1/4W 1/4W 1/4W 1/4W D
C514 C516 C515 C513
NM NM NM NM
R516 R518 R517 R515
TP68

TP69

47K 47K 47K 47K

10P
10P
10P
10P

C518
C520
C519
C517

C523
C522
C524 C521
0.22 0.22 0.22 0.22
R520 R522 R524 R526 R528 R527 R525 R523 R521 R519
120 1.1K 4.7K 2.2K 120 120 2.2K 4.7K 1.1K 120
Q512 Q514 Q513 Q511
1/4W 1/4W 1/4W 1/4W
2SA1038S 2SC2389S 2SC2389S 2SA1038S
A-a A-b

Q516 Q515
TP73 TP72 TP71 TP70
KTC3114A KTC3114A
C526 C525
0.001
0.001
22
22

3216
3216

22
22
R531
R529

3216
3216

R530
R532
C531 R535 R533 C527
C
C528 R534 R536 C532
NM 47K 47K NM
NM 47K 47K NM TP75 TP74
TP79 TP78
NM
C533
NM
C529

NM
NM

C530
C534
R538 R540 R539 R537
0.1 0.1 0.1 0.1 Q517
Q518 Q520 Q519
2W 2W 2W 2W 2SD2439
2SD2439 2SB1588 2SB1588
OP OP OP OP

R54247K
R54147K

D502 R544 R543 D501

TP81 TP77
MA111 560K 560K
MA111
C536 C535
NM NM
Q522 Q521
KTC3911S KTC3911S
GL GL
B
R546 R545
47K 47K
R548 C538 C537 R547
10 0.033 0.033 10
1/4W 1/4W
C5400.001 C5390.001

+29 dB
are printed wrongly each other.

C542 NM C541 NM
3216 3216 TP85
A

TP97 TP84
TP96 TP83
TP95 TP82
TP94

TP93
TP92
TP91
TP90
TP89
TP88
TP87
TP86
C544 NM C543 NM
Silk-prints of "L" and "R" on the Amp Unit

("L" should be "R", and "R" should be "L".)

2 1 2 1 JA501
JA502
CKE1057-A CKE1057-A

L-

R-
L+

R+
SP OUTPUT
AMP UNIT
A
4 3 2 1
 560
120
NM

R50
1/4W
C52
0.22
R52
1/4W
R734

NM

NM

D708
D709
C712

1SS133
1SS133
5

5
D710 R725 R727

1SS133 330 2.2K

33K

C709
0.01
R726

D711
Q709

1SS133
TP19

2SA1037AK
12K

R728

22K

R724
TP24
R729 TP18

Q710
6.8K

2SC2412K
16K

R730
E1 C1
R802

9
8
R

Q711
E2 GND NM

R731
6.8K

7
2SC2412K

10
C2 RT

11
R801 15K
Vcc CT
C710

12
220/6.3

6
6

C801 0.001
OPC DTC

13
R814 1K
Ref FEEDBACK

14
IC801KIA494AF
2IN- 1IN-

15
C706
0.22
R713
330K
TP16
TP11
TP12
TP13
TP14
TP15

2IN+ 1IN+ R714

16
10K

NM

C711
R815 47K R717 JA805

R702
7.5K
CND2458-A
TP17

47

47K

R723
C807 220/6.3 Q713 >
2SC2412K L801 FUSE (25A)

D702
R R712
1SS133
K000225700 JA804
Q714 22K
36uH CND2458-A

NM
2SA1037AKR

R710
3.9K
C704

1K
R704 TP20

R716
BLUE LED

Q703
4.7K

KN2907AS

GM-3400T/XJUC
11 TH701

220

R715
D705 Q705

NM
0 D701 R701

R720
470 NHSB046AT 2SC2412K R705
R

Q702

R 2.2K
2.2K MTZJ7.5B
2SC2412K

1/4W

22K

R708
100

R722
C703

7
7

100/16

R721
4.7K
1/2W
NM

JA801

10K
0.001

D707
R732
2.7K

TH702

R709
2.2K
CKE1055-A
R703
2.2K
1/4W
D804
D803
C802
0.01
2012
C803
C804
0.22

1A4-E
1A4-E

HZS3A2TD-E
NM 3216

+B

D706
C708
0.01
C707
C702
C701

22/25

1SS133
R733 100 GND
3 2 1

REM
1/4W
TP1
TP2
TP3
TP4
TP5

KN801
CZK2969-A-T

NOTE :
The > mark found on some component parts indicates
Symbol indicates a resistor.
the importance of the safety factor of the part.
No differentiation is made between chip resistors and
Therefore, when replacing, be sure to use parts of
discrete resistors.
8

8
identical designation.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.

A-a A-b NM : No Mount

A-b
23
E
A

D
C

F
B
 4 3 2 1
24
GM-3400T/XJUC
A-a
SP LEVEL INPUT RCA INPUT
L-
R-
L+
Lch

R+
Rch

TP37
4 3 2 1
CKB1068-B
JA101

TP40
F
TP41 TP44
CKM1463-A
JA103

TP42 TP45
TP43 TP46
TP36 TP47
+15V
NM
NM

C114
C113

10/25
10/25
10/25
10/25

C118
C116
C117
C115
R120
R119

51K
51K
51K
51K

1/4W
1/4W
1/4W
1/4W

R124
R122
R123
R121
1/4W
1/4W
470
470

NM
NM
NM
NM

R128
R126
R127
R125

C119
10/25
10/25

C112
C111

NM E
L802

C102 C101
NM
R831

470P 470P
R104 R103
NM

22K 22K
C106

KN802
R101
C105

NM
NM

R114
R113

NM
D104 D102 D103 D101
NM
NM

0.0047

1SS355 1SS355 1SS355 1SS355

D108 D106 D107 D105
1SS355 1SS355 1SS355 1SS355
R11110K
0.25%
R110 10K R10910K
0.25% 0.25% C10747P
R108 10K
0.25% R112 10K R10710K
C104 0.25% 0.25%
47P C108 47P C103
D
47P
R106 10K R10510K
0.25% 0.25%
TP54 AOUTPUT 1 V+ TP50 AOUTPUT V+
8
1
8

IC102
A-INPUT BOUTPUT TP52 A-INPUT BOUTPUT
TP48

2
7
2
7

R827
A-a A-b

NM
NM

C126
C124

TP55 B-INPUT TP51 B-INPUT

3
6
3
6
0 dB / 0 dB

TP38
A+INPUT A+INPUT
C125
IC101NJM4565M-D

NM
NM
C123

NJM4565M-D
TP53 B+INPUT
TP49

4
4

5
5

V- B+INPUT V-

+VD
D112 D110 D111 D109
BUFFER/ISO.AMP

1SS355 1SS355 1SS355 1SS355

TP56
C
C811 C812
0.033
0.033
TP58

68K
68K

R306
R305

1W
OUTPUT
68K
68K

0.039
0.039

C302
R308
R307
C301
C304 C303

VD
0.022 0.022
TP59 TP57

-27.8 V
+27.8 V
5
4
B_+IN V-

IC301
R314
0 dB

6
3
LPF

VH
130K B_-IN A_+IN
B
R313

7
2

-27.9 V
B_OUT A_-IN 130K

+28.0 V
8
1

NJM4558MD
V+ A_OUT

15 V
S301

-15.2 V
00221461

+15.1 V
LPF

LPF
TP61 TP60

OFF

OFF
LPF

2.2K
2.2K

R310
R309

OFF

10K
VR301
R312 R311
56

MIN
GAIN
56
A

NM
R707
A-b

MAX
Q712
DTA124EKA
D708 R706
1SS133 NM

-31.5 dB ~ -2.2 dB

R
R

1
1
D709

-9.3 d
4 3 2 1
 8 7 6 5
25
GM-3400T/XJUC
A-a
-15V

F
R834 R833 R835
3.3K 3.9K 0
+15V

R832
100
Q825
1/4W
KTC9014
C829 C828
ABCD
47/16 47/16
EC

D806 D805
EC
B

Q822

ABC
Q821

ABCD

MTZJ16B MTZJ16B
KTC9015
KTC9014

R830 C827 C826 R829

3.3K 3.3K
22/25 22/25 R836
1/2W 1/2W
R837 NM1/2W
1/2W NM R838
E
R839 NM1/2W
NM
NM

R826
R825

C825 C824 NM 1/2W

TP35 TP34
3300/35 3300/35
105 105
-VH
+VH

R824 R823
NM NM
1/2W 1/2W
TP6
TP7
MODEL
TP8
TP9

GM-3400T/XJES
GM-3400T/XJUC
GM-3400T/XJEW5
TP10
C823 R822 R821 C822
*L804
*L803

0.001 22 22
*JW126
*JW124
*JW123
*JW122

0.001
1/2W 1/2W

L803
BL02RN1R3N1A
BL02RN1R3N1A

TP33
D
TP32
D822

L804
FML-22R D821
FML-22S
C821 C820 R820
NM NM NM
R828
R827

A-a A-b
10 1/2W
10 1/2W

TP39 TP38
-VD
+VD

C831
C830

220/35
220/35

JW122 JW123 JW124

10:5

T801

TP30
TP31
C833 C832

JW126
NM NM
105
C810

3300/16

C
R810 C806 C805 R809
22 22
0.0047 0.0047
1/2W 1/2W

Q804
Q803
FKV550N

S
S

FKV550N D
D

G
G

120
120

1/2W
1/2W

R808
R807
R806 R805
4.7K 4.7K
Q824 Q802 Q801 Q823
KTC3875S KTA1504S KTA1504S KTC3875S
OYG OYG
B
TP29
TP28
R804 R803
3.3K 3.3K

11K
R812
TP27 R813

TP26
27K

100
Ref
Vcc

2IN-
E2
E1

C2

2IN+
OPC

470
R711 TH701
16 15 14 13 12 11 10 9

C807
R815
A R709 R708
IC801KIA494AF

Q714
A-b
2.2K 22K

47K
1 2 3 4 5 6 7 8

2SA1037AKR
220/6.3
D708

C1

CT
RT

1IN-
DTC

1IN+
GND
1SS133

FEEDBACK
R710 D709
8 7 6 5
 1 2 3 4

11. PCB CONNECTION DIAGRAM

11.1 AMP UNIT
A NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB
include all necessary parts for
A AMP UNIT
several destination.
For further information for
respective destinations, be sure
to check with the schematic dia-
gram.
2.Viewpoint of PCB diagrams
Connector Capacitor

SIDE A

B
SIDE B
P.C.Board Chip Part

FRONT

A
GM-3400T/XJUC
26
1 2 3 4
5 6 7 8

A
SIDE A

A
GM-3400T/XJUC
5 6 7 8
27
 1 2 3 4

A AMP UNIT

A
GM-3400T/XJUC
28
1 2 3 4
5 6 7 8

A
SIDE B

Silk-prints of "L" and "R" on the Amp Unit

are printed wrongly each other.
("L" should be "R", and "R" should be "L".)

A
GM-3400T/XJUC
5 6 7 8
29
 1 2 3 4

12. ELECTRICAL PARTS LIST

NOTE:
A Parts whose parts numbers are omitted are subject to being not supplied.
The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Meaning of the figures and others in the parentheses in the parts list.
B Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 714 Transistor 2SA1037K
Unit Number : CZW5581(UC,EW5) Q 801 Transistor KTA1504S
Unit Number : CZW5582(ES) Q 802 Transistor KTA1504S

Unit Name : Amp Unit Q 803 Transistor FKV550N

Q 804 Transistor FKV550N
Q 821 Transistor KTC9014
C
Q 822 Transistor KTC9015

A
Unit Number : CZW5581(UC,EW5)
Q 823 Transistor KTC3875S

Q 824 Transistor KTC3875S

Unit Number : CZW5582(ES) Q 825 Transistor KTC9014
D 101 Diode 1SS355
Unit Name : Amp Unit D 102 Diode 1SS355
D 103 Diode 1SS355
MISCELLANEOUS
D 104 Diode 1SS355
IC 101 IC NJM4565MD D 105 Diode 1SS355
IC 102 IC NJM4565MD D 106 Diode 1SS355
IC 301 IC NJM4558MD D 107 Diode 1SS355
D
IC 501 IC NJM2068MD D 108 Diode 1SS355
IC 801 IC KIA494AF
D 109 Diode 1SS355
Q 301 Transistor 2SC2412K D 110 Diode 1SS355
Q 302 Transistor 2SC2412K D 111 Diode 1SS355
Q 511 Transistor 2SA1038S D 112 Diode 1SS355
Q 512 Transistor 2SA1038S D 501 Diode 1SS355
Q 513 Transistor 2SC2389S
D 502 Diode 1SS355
Q 514 Transistor 2SC2389S D 701 Diode MTZJ7R5(B)
Q 515 Transistor KTC3114 D 702 Diode 1SS133
Q 516 Transistor KTC3114 D 705 Chip LED NHSB046AT
E Q 517 Transistor 2SD2439 D 706 Diode 1SS133
Q 518 Transistor 2SD2439
D 707 Diode HZS3L(A2)
Q 519 Transistor 2SB1588 D 708 Diode 1SS133
Q 520 Transistor 2SB1588 D 709 Diode 1SS133
Q 521 Transistor KTC3911S D 803 Diode 1A4-E
Q 522 Transistor KTC3911S D 804 Diode 1A4-E
Q 702 Transistor 2SC2412K
D 805 Diode MTZJ16(B)
Q 703 Transistor KN2907AS D 806 Diode MTZJ16(B)
Q 705 Transistor 2SC2412K D 821 Diode FML22S
Q 709 Transistor 2SA1037K D 822 Diode FML22R
Q 710 Transistor 2SC2412K L 801 Choke Coil 36 uH CZT2944
F Q 711 Transistor 2SC2412K
L 803 Coil(ES) CZT2945
Q 712 Chip Digital Transistor DTA124EKA L 804 Coil(ES) CZT2945
Q 713 Transistor 2SC2412K T 801 Transformer CZT2946

GM-3400T/XJUC
30
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
TH701 Posistor CZC2982 R 518 RS1/16S473J
TH702 Thermistor CZC2994 R 519 120 ohm CZC2986
R 520 120 ohm CZC2986
S 301 Switch(LPF-OFF) CZS2928 R 521 RS1/16S112J A
VR301 Variable Resistor 10 kohm CZC2975 R 522 RS1/16S112J
JA101 Pin Jack CKB1068
JA103 Socket CKM1463 R 523 RS1/16S472J
JA501 Terminal CKE1057 R 524 RS1/16S472J
R 525 RS1/16S222J
JA502 Terminal CKE1057 R 526 RS1/16S222J
JA801 Terminal CKE1055 R 527 120 ohm CZC2986
JA804 Terminal CND2458
JA805 Terminal CND2458 R 528 120 ohm CZC2986
KN801 Terminal CZK2969 R 529 RS1/8S220J
R 530 RS1/8S220J
RESISTORS R 531 RS1/8S220J
R 532 RS1/8S220J B
R 103 RS1/16S223J
R 104 RS1/16S223J R 533 RS1/16S473J
R 105 10 kohm CCN1152 R 534 RS1/16S473J
R 106 10 kohm CCN1152 R 535 RS1/16S473J
R 107 10 kohm CCN1152 R 536 RS1/16S473J
R 537 0.1 ohm CZC2974
R 108 10 kohm CCN1152
R 109 10 kohm CCN1152 R 538 0.1 ohm CZC2974
R 110 10 kohm CCN1152 R 539 0.1 ohm CZC2974
R 111 10 kohm CCN1152 R 540 0.1 ohm CZC2974
R 112 10 kohm CCN1152 R 541 RS1/16S473J
R 542 RS1/16S473J
R 119 470 ohm CZC2987 C
R 120 470 ohm CZC2987 R 543 RS1/16S564J
R 121 51 kohm CZC2988 R 544 RS1/16S564J
R 122 51 kohm CZC2988 R 545 RS1/16S473J
R 123 51 kohm CZC2988 R 546 RS1/16S473J
R 547 10 ohm CZC2984
R 124 51 kohm CZC2988
R 301 RS1/16S103J R 548 10 ohm CZC2984
R 302 RS1/16S103J R 701 2.2 kohm CZC2980
R 305 RS1/16S683J R 702 RS1/16S752J
R 306 RS1/16S683J R 703 2.2 kohm CZC2980
R 704 RS1/16S472J
R 307 RS1/16S683J
R 308 RS1/16S683J R 705 RS1/16S222J D
R 309 RS1/16S222J R 708 RS1/16S223J
R 310 RS1/16S222J R 709 RS1/16S222J
R 311 RS1/16S560J R 710 RS1/16S392J
R 711 RS1/16S101J
R 312 RS1/16S560J
R 313 RS1/16S134J R 712 RS1/16S223J
R 314 RS1/16S134J R 713 RS1/16S334J
R 501 RS1/16S103J R 714 RS1/16S103J
R 502 RS1/16S103J R 715 RS1/16S221J
R 716 RS1/16S102J
R 503 RS1/16S271J
R 504 RS1/16S271J R 717 RS1/16S470J
E
R 505 RS1/10S223J R 721 RD1/2PM472J
R 506 RS1/10S223J R 722 RS1/16S101J
R 507 560 ohm CZC2981 R 723 RS1/16S473J
R 724 RS1/16S223J
R 508 560 ohm CZC2981
R 509 RS1/16S153J R 725 RS1/16S331J
R 510 RS1/16S153J R 726 RS1/16S333J
R 511 RS1/16S153J R 727 RS1/16S222J
R 512 RS1/16S153J R 728 RS1/16S123J
R 729 RS1/16S682J
R 513 560 ohm CZC2981
R 514 560 ohm CZC2981 R 730 RS1/16S163J
R 515 RS1/16S473J R 731 RS1/16S682J F
R 516 RS1/16S473J R 732 RS1/16S272J
R 517 RS1/16S473J R 733 100 ohm CZC2985
R 801 RS1/16S153J

GM-3400T/XJUC
5 6 7 8
31
 1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 803 RS1/16S332J C 537 CKSRYB333K50
R 804 RS1/16S332J C 538 CKSRYB333K50
R 805 RS1/16S472J C 539 CQMA102J50
R 806 RS1/16S472J C 540 CQMA102J50
A
R 807 RD1/2PM121J C 702 CKSRYB102K50

R 808 RD1/2PM121J C 703 100 uF/16 V CZC2991

R 809 RD1/2PM220J C 706 CKSRYB224K16
R 810 RD1/2PM220J C 707 22 uF/25 V CZC2989
R 812 RS1/16S113J C 708 CKSRYB103K50
R 813 RS1/16S273J C 709 CKSRYB103K50

R 814 RS1/16S102J C 710 220 uF/6.3 V CZC2992

R 815 RS1/16S473J C 801 CCSRCH102J50
R 821 RD1/2PM220J C 802 CKSQYB103K50
R 822 RD1/2PM220J C 804 CFTLA224J50
B R 827 RD1/2PM100J C 805 CKSRYB472K50

R 828 RD1/2PM100J C 806 CKSRYB472K50

R 829 RD1/2PM332J C 807 220 uF/6.3 V CZC2992
R 830 RD1/2PM332J C 810 3 300 uF/16 V CZC2977
R 832 100 ohm CZC2985 C 811 CKSRYB333K50
R 833 RS1/16S392J C 812 CKSRYB333K50

R 834 RS1/16S332J C 822 CCSRCH102J50

R 835 RS1/16S0R0J C 823 CCSRCH102J50
C 824 3 300 uF/35 V CZC2978
CAPACITORS C 825 3 300 uF/35 V CZC2978
C 826 22 uF/25 V CZC2989
C C 101 CCSRCH471J50
C 102 CCSRCH471J50 C 827 22 uF/25 V CZC2989
C 103 CCSRCH470J50 C 828 47 uF/16 V CZC2990
C 104 CCSRCH470J50 C 829 47 uF/16 V CZC2990
C 106 CQMA472J50 C 830 220 uF/35 V CZC2993
C 831 220 uF/35 V CZC2993
C 107 CCSRCH470J50
C 108 CCSRCH470J50
C 111 CEAT100M50
C 112 CEAT100M50
C 115 CEAT100M50

C 116 CEAT100M50
D C 117 CEAT100M50
C 118 CEAT100M50
C 301 CFTLA393J50
C 302 CFTLA393J50

C 303 CKSRYB223K50
C 304 CKSRYB223K50
C 501 CCSRCH330J50
C 502 CCSRCH330J50
C 503 CEAT101M10

C 504 CEAT101M10
C 505 CCSRCH680J50
E
C 506 CCSRCH680J50
C 507 CCSRCH680J50
C 508 CCSRCH680J50

C 517 CCSRCH100D50
C 518 CCSRCH100D50
C 519 CCSRCH100D50
C 520 CCSRCH100D50
C 521 CKSRYB224K16

C 522 CKSRYB224K16
C 523 CKSRYB224K16
F C 524 CKSRYB224K16
C 525 CKSRYB102K50
C 526 CKSRYB102K50

GM-3400T/XJUC
32
1 2 3 4