MODEL ZQ127/25Y
DRILL PIPE POWER TONG
PARTS OPERATION AND
MAINTENACE MANUAL
Model ZQ127/25Y Drill Pipe Power Tong
SAFETY CAUTION
1.Operators should read and understand this manual before operation.
2.Operators should wear protective clothing, hard hat and safety boots.
3.Tie the back guy according to the instructions.
4.Make sure to operate at the side of the tong opening.
5.Close the safety door in make-up/break-out operation.
6.Keep hands away from rotating parts.
7.Keep sundries out of the operation range.
8.Cut off the hydraulic source and move the tong off the wellhead during maintenance,
changing dies or other parts.
9.Never use the power tong under over-pressure or over-torque conditions, otherwise
the tubing will be damaged and so the planetary gear of the tong will be damaged.
10.Keep the tong turning center according to the center of tubing before
make-up/break-out, otherwise the planetary gear of the tong would be damaged.
11.Don’t dismantle or add parts to the tong.
12.Please adopt the original fitting parts made by TEDA.
If the manual is changed or revised later, we have no obligation to notify any
person.
Model ZQ127/25Y Drill Pipe Power Tong
TABLE OF CONTENTS
1 . S ummary ………………………………………………………………1
2 . Techni cal parameter……………………………………………………1
3 . Ins tal l ati o n……………………………………………………………1
3 . 1 l i f ti ng …………………………………………………………………1
3 . 2 l e v e l i ng ………………………………………………………………1
3 .3 Tie the back g uy………………………………………………………1
4. Operation Instruction……………………………………………………2
4.1 The Choice of Die Seats………………………………………………2
4.2 The Choice of Die………………………………………………………2
4.3 Note of break out operation……………………………………………2
5. Maintenance and lubrication……………………………………………3
6. Common troubles and remedy……………………………………………4
7. Attached figures and part list……………………………………………5
8 . Eas y - damag ed parts l i s t……………………………………………2 3
Model ZQ127/25Y Drill Pipe Power Tong
1. Summary
Model ZQ127-25Y Drill Pipe Tong is mouth-opening type power tong used for make up and break out 2
3/8"-3 1/2" drill pipe, 3 1/2"-4 1/2"tubing and 4 1/2"-5 1/2"casing in the oil field well workover operation.
2. Technology Parameter
2.1 Application Range
2 3/8"-3 1/2"drill pipe, 3 1/2"-4 1/2" tubing and 4 1/2"-5 1/2" casing
2.2 Rated Oil Supply Pressure 16Mpa
2.3 Rated Oil Supply Amount 120 lpm
2.4 Rated High Gear Torque 5.1 KN.m
2.5 Rated Low Gear Torque 25 KN.m
2.6 Rated Rotation Speed at High Gear 43 rpm
2.7 Rated Rotation Speed at Low Gear 8 rpm
2.8 Overall Weight 680 kg
2.9 Dimension of Combination tongs 1270×770×780mm
3. Installation
3.1 Lifting
Connect the lifting bucket to the lifting bar of the master tong, lift the drill pipe tong at the well servicing
rig. The lifting point is supposed to be 15m above the wellhead. In the state of free suspension, the center of
the tong head is 0.5m away from the wellhead. The suspension height is appropriate when the backup tong
clamps the drill pipe connector or the coupling of tubing, or casing.
3.2 Leveling
Adjusting the adjusting screws on the lifting bar to keep the drill pipe level, if not, the clamping will fail to
work.
3.3 Tie the back guy
Tie one end of the back guy to the rig, the other end to the seat of the back guide pole of the drill pipe
tong, the back guy is supposed to be able to bear load of 50 KN. When the drill pipe is in the making-up state,
the back guy should be vertical to the drill pipe so as to make the operator safety.
1
Model ZQ127/25Y Drill Pipe Power Tong
4.Operation Instruction
4.1 The Choice of Die Seats
Steel
Part No. Part Name Application Range Note
Mark
ZQ25.1.1-7(1) Die Seat (1) 2 3/8" drill pipe, 3 1/2"tubing 3 1/2"
ZQ25.1.1-7(2) Die Seat (2) 2 7/8" drill pipe, 4"tubing 4"
4 1/2" tubing, 3 1/2" tubing coupling, 4 1/2" For
ZQ25.1.1-7(3) Die Seat (3)
4 1/2"casing selection
3 1/2" drill pipe, 4" tubing coupling, 5"
ZQ25.1.1-7(4) Die Seat (4)
5" casing, 4 1/2" casing coupling
4 1/2" tubing coupling, 5 1/2" casing, 5 1/2"
ZQ25.1.1-7(5) Die Seat (5)
5" casing coupling
5 1/2"casing coupling 6 1/8" For
ZQ25.1.1-7(6) Die Seat (6)
selection
Choose die seats according to the seat marks and part numbers.
4.2 Choice of dies
Part No. Part Name Application Range Steel Mark Note
2 3/8"-3 1/2" drill pipe, 3 1/2"-4 1/2" 89-114
XYQ12.Z-01.12(2) Die tubing, 3 1/2" tubing coupling, 4 1/2"
casing
3 1/2" drill pipe, 4"-4 1/2" tubing 121-156
XYQ12.Z-01.12(3) Die coupling, 5"-5 1/2" casing, 5"-5 1/2"
casing coupling
Choose dies according to the steel marks and part numbers.
4.3 Note of break out operation
The pin axle of the guide pole must be moved to the lowest hole when break out operation.
2
Model ZQ127/25Y Drill Pipe Power Tong
5. Maintenance and lubrication
5.1 Before work, the fastening screws must be checked to see whether they are loose, if loose, the screws
must be tightened.
5.2 Before work, enough lubricating grease should be added to each transmitting part.
5.3 After each use, the tong body must be check to clean up water or oil stain in time.
5.4 After each well operation is over, the tong must be cleaned with diesel fuel, and lubricating grease must
be added to each transmitting part after cleaning.
5.5 After each operation, the steam is prohibited to clean the power tong for it could cause the grease lost.
5.6 The temperature of the hydraulic should be kept below 65℃, overheating may lead to the failure of the
hydraulic system sealing.
5.7 The hydraulic oil must be kept clean to guarantee the normal filtering of the oil filter, if the oil is dirty, it
should be replaced in time.
5.8 The choice of hydraulic oil
5.8.1 YC-N46 low freezing hydraulic oil, suitable ambient temperature: -20℃-+40℃.
5.8.2 YB-N46 wear resistant hydraulic oil, suitable ambient temperature: -10℃-+40℃.
5.8.3 YA-N46 ordinary hydraulic oil, suitable ambient temperature: 0℃-+40℃.
3
Model ZQ127/25Y Drill Pipe Power Tong
6. Common troubles and remedy
Common troubles Reason Remedy
Cleaning up sundries in the
Die groove fill with hard objects
groove
Tong dies slip Dies over worn Replace new dies
Adjusting tong level (master
Tong body not level
tong and backup tong)
Master tong head backup
Retaining pin can’t be contained by Turn the reset knob and reset
tong head not in alignment
reset knob axle again
with the opening
The turning direction of jaw plate
Master tong clamps well frame of backup tong opposite to Exchange the positions of the
while backup tong slips the turning direction of the master two hoses.
tong
4
Model ZQ127/25Y Drill Pipe Power Tong
7. Attached figures and part list.
7.1 General assembly (Fig1. Table1)
Fig1. General assembly
Table1. Detailed table for General assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-1 ZQ25.1 Master tong 1
2 ZQ25-3 ZQ25.3 Front guide pole assembly 2
3 ZQ25-2 ZQ25.2 Backup tong 1
4 ZQ25-4 ZQ25.4 Back guide pole assembly 1
5 ZQ25-5 XYQ12.YD-01.1 Hydraulic bucket 1
5
Model ZQ127/25Y Drill Pipe Power Tong
7.2 Master tong (Fig2. Table2)
Fig2. Master tong
Table2. Detailed table for Master tong
Item Purchase No. Part No. Part name and Description QTY
1 Shell assembly and parts 1
tong head assembly and brake
2 1
mechanism
3 ZQ25-30 Hydraulic motor J6K-625 1
4 Hand control valve and lift valve 1
5 Drive gear assembly and parts 1
6 ZQ25-21 ZQ25.1.6 Shift mechanism assembly 1
6
Model ZQ127/25Y Drill Pipe Power Tong
7.2.1 Shell assembly and parts (Fig3. Table3)
Fig3. Shell assembly and parts
7
Model ZQ127/25Y Drill Pipe Power Tong
Table3. Detailed table for Shell assembly and parts
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-47 GB70 Hexagon socket head cap screw M10×25 29
2 ZQ25-111 GB93 Washer 10 23
3 ZQ25-126 ZQ25.1.9-1 Safety door shaft 1
4 ZQ25-127 GB91 Cotter pin 5×35 1
5 ZQ25-53 Tension spring（Φ17×95） 1
6 ZQ25-125 ZQ25.1.9.1 Main body of safety door 1
7 ZQ25-121 ZQ25.1.8-6 Pin shaft 1
8 ZQ25-116 ZQ25.1.8-1 Tong head cover 1
9 ZQ25-12 ZQ25.1-2 Tong body 1
10 ZQ25-8 XYQ3C.Z.3 Fore handle（RH） 1
11 ZQ25-6 ZQ25.1-1 Fore support seat 2
12 ZQ25-7 GB70 Hexagon socket head cap screw M12×25 4
13 ZQ25-202 GB93 Washer 12 4
14 ZQ25-10 GB5781 Hex head bolt M10×20 6
15 ZQ25-177 GB65-85 Slotted cylinder head screw M6×10 12
16 ZQ25-203 ZQ25.1-14A Name plate 1
17 ZQ25-48 ZQ25.1.7 Hanging rod 1
18 ZQ25-51 GB70 Hexagon socket head cap screw M12×100 2
19 ZQ25-204 ZQ25.1.7-1A Hanging caput 2
20 ZQ25-50 GB91 Cotter pin 4×30 2
21 ZQ25-49 ZQ25.1-16 Hanging pin shaft 2
22 ZQ25-29 GB1152 Oil cup M10×1 2
23 ZQ25-46 ZQ25.1-13A hanging seat 2
24 ZQ25-9 XYQ3C.Z.4 Fore handle（LH） 1
25 ZQ25-55 XYQ3C.Z-37 Back handle 2
26 ZQ25-26 XYQ12.Z-62 Tail guy pin 1
27 ZQ25-27 GB91 Cotter pin 5×35 1
28 ZQ25-24 ZQ25.1-4 Back guide rod seat 1
29 ZQ25-25 GB1096 Parallel key 12×40 2
30 ZQ25-23 XYQ3C.Z-21 spring 1
31 ZQ25-22 XYQ12.Z.1-21 Locating block 1
32 ZQ25-100 ZQ25.1.5-8 Bearing cover 1
33 ZQ25-20 GB70 Hexagon socket head cap screw M8×25 6
8
Model ZQ127/25Y Drill Pipe Power Tong
7.2.2 Tong head assembly(Fig4. Table4)
Fig4. tong head assembly
9
Model ZQ127/25Y Drill Pipe Power Tong
Table4. Detailed table for tong head assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-69 ZQ25.1.1-9 Retainer pin 1
2 ZQ25-70 GB70 Hexagon socket head cap screw M12×30 30
3 ZQ25-68 ZQ25.1.1-8 Open gear 1
4 ZQ25-58 ZQ25.1.1-3 Jaw set bracket 1
5 ZQ25-57 ZQ25.1.1-2 Ramp 4
6 ZQ25-7 GB70 Hexagon socket head cap screw M12×25 12
7 ZQ25-56 ZQ25.1.1-1 Main body 1
Each
ZQ25-65 XYQ12.Z-01.12（2-3） Die （2-3）
8 for 4
Each
ZQ25-64 ZQ25.1.1-7（1-5） Die seat（1-5）
9 for 2
10 ZQ25-62 ZQ25.1.1-6 Roller shaft 2
11 ZQ25-63 GB71 Slotted cone end fastening screw M8×10 4
12 ZQ25-59 ZQ25.1.1-4 Jaw set 2
13 ZQ25-61 ZQ25.1.1-5 Roller 2
14 ZQ25-60 GB119 Cylindrical pin 6×18 4
15 ZQ25-66 XYQ12.Z-01.11 Screw retainer pin 20
16 ZQ25-67 XYQ12.B-10 Set screw 2
10
Model ZQ127/25Y Drill Pipe Power Tong
7.2.3 Tong head brake mechanism(Fig5. Table5)
Fig5. tong head brake mechanism
11
Model ZQ127/25Y Drill Pipe Power Tong
Table5. Detailed table for tong head brake mechanism
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-124 ZQ25.1.8-9 Brake blot 11
2 ZQ25-123 ZQ25.1.8-8 Brake spring 11
3 ZQ25-117 ZQ25.1.8-2 Friction disc 3
4 ZQ25-16 GB68 Slotted countersunk screw M5×10 63
5 ZQ25-109 ZQ25.1.6-2 shim 1
6 ZQ25-118 ZQ25.1.8-3 Brake steel plate 1
7 ZQ25-119 ZQ25.1.8-4 Knob shaft 1
8 ZQ25-14 XYQ12.Z-03 Centralizing roller 21
9 ZQ25-13 ZQ25.1-3 Centralizing roller shaft 21
10 ZQ25-116 ZQ25.1.8-1 Tong head cover 1
11 ZQ25-122 ZQ25.1.8-7 Brake disc 1
Hexagon socket head cap screw M6
12 ZQ25-87 GB70 1
×10
13 ZQ25-120 ZQ25.1.8-5 knob 1
Hexagon socket head cap screw M10
14 ZQ25-47 GB70 4
×25
15 ZQ25-55 XYQ3C.Z-37 Back handle 2
16 ZQ25-121 ZQ25.1.8-6 Pin shaft 1
12
Model ZQ127/25Y Drill Pipe Power Tong
7.2.4 Idle shaft assembly (Fig6. Table6)
Fig6.Idle shaft assembly
Table6. Detailed table for Idle shaft assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-86 XYQ3C.Z-5 Locating disc 2
2 ZQ25-80 ZQ25.1.3-4 Idler shaft 2
3 ZQ25-76 ZQ25.1.3-2 Seal ring（1） 4
4 ZQ25-77 GB1235-76 O ring 63×5.7 4
5 ZQ25-75 ZQ25.1.3-1 idler（1） 2
6 ZQ25-78 Roller Φ10×30 40
7 ZQ25-79 ZQ25.1.3-3 Shaft sleeve（1） 2
13
Model ZQ127/25Y Drill Pipe Power Tong
7.2.5 Duplex gear assembly (Fig7. Table7)
Fig7. Duplex gear assembly
Table7. Detailed table for Duplex gear assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-87 GB70 Hexagon socket head cap screw M6×10 1
2 ZQ25-86 XYQ3C.Z-5 Locating disc 1
3 ZQ25-84 ZQ25.1.4-4 Idler (2) 1
4 ZQ25-76 ZQ25.1.3-2 Seal ring（1） 4
5 ZQ25-77 GB1235-76 O ring 63×5.7 4
6 ZQ25-29 GB1152 Oil cup M10×1 1
7 ZQ25-85 ZQ25.1.4-5 Duplex shaft 1
8 ZQ25-78 Roller Φ10×30 60
9 ZQ25-83 ZQ25.1.4-3 shim 1
10 ZQ25-82 ZQ25.1.4-2 Shaft sleeve（2） 1
14
Model ZQ127/25Y Drill Pipe Power Tong
11 ZQ25-81 ZQ25.1.4-1 Duplex gear（1） 1
7.2.6 Power input shaft assembly (Fig8. Table8)
Fig8. Power input shaft assembly
15
Model ZQ127/25Y Drill Pipe Power Tong
Table8. Detailed table for Power input shaft assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-88 ZQ25.1.5-1 Power input shaft 1
2 ZQ25-89 GB276 Deep groove ball bearing 112 1
3 ZQ25-92 ZQ25.1.5-3 Duplex gear（2） 1
4 ZQ25-91 GB1567 Thin flat key 28×10×63 4
5 ZQ25-90 ZQ25.1.5-2 Clutch gear 1
6 ZQ25-94 ZQ25.1.5-5 Inner gear sleeve 1
7 ZQ25-93 ZQ25.1.5-4 Inner spline gear 1
8 ZQ25-95 ZQ25.1.5-6 Shifting gear 1
9 ZQ25-96 ZQ25.1.5-7 Seal ring（2） 1
10 ZQ25-99 GB1235 O ring 80×3.1 1
11 ZQ25-98 GB276 Deep groove ball bearing 207 1
12 ZQ25-100 ZQ25.1.5-8 Bearing cover 1
13 ZQ25-78 Roller Φ10×30 68
14 ZQ25-97 GB1235 O ring 40×3.1 1
16
Model ZQ127/25Y Drill Pipe Power Tong
7.2.7 Shifting mechanism assembly (Fig9. Table9)
Fig9. Shifting mechanism assembly
Table9. Detailed table for Shifting mechanism assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-101 XYQ12.Z-19.01 Shaft sleeve 2
2 ZQ25-104 XYQ3C.Z.6-4 Roller shaft 1
3 ZQ25-105 GB91 Cotter pin 2×10 1
4 ZQ25-103 XYQ3C.Z.6-3 roller 1
5 ZQ25-106 XYQ3C.Z.6-5 Roller support seat 1
6 ZQ25-107 GB1096 Flat key 6×6×40 1
7 ZQ25-109 ZQ25.1.6-2 shim 1
8 ZQ25-87 GB70 Hexagon socket head cap screw M6×10 1
9 ZQ25-112 XYQ12.Z-19.04 Bolt shaft 2
10 ZQ25-114 GB276 Deep groove ball bearing 100 2
11 ZQ25-113 GB848 Washer 10 2
12 ZQ25-102 XYQ12.Z-19.02 fork 1
13 ZQ25-111 GB93 Washer 10 2
14 ZQ25-110 GB6170 Nut M10 2
15 ZQ25-108 ZQ25.1.6-1 Fork shaft 1
16 ZQ25-115 ZQ25.1.6.1 Operating handle assembly 1
17 ZQ25-205 XYQ3C.Z.5-10 Handle 1
17
Model ZQ127/25Y Drill Pipe Power Tong
7.3 Backup tong
7.3.1 Backup tong head assembly (Fig10. Table10)
Fig10. Backup tong head assembly
18
Model ZQ127/25Y Drill Pipe Power Tong
Table10. Detailed table for Backup tong head assembly
Item Purchase No. Part No. Part name and Description QTY
Each
1 ZQ25-65 XYQ12.Z-01.12 Die （2-3）
for 4
2 ZQ25-62 ZQ25.1.1-6 Roller shaft 2
3 ZQ25-63 GB71 Slotted cone end fastening screw M8×10 4
4 ZQ25-59 ZQ25.1.1-4 Jaw set 2
Each
5 ZQ25-64 ZQ25.1.1-7 Die seat (1、2、4、6)
for 2
6 ZQ25-61 ZQ25.1.1-5 Roller 2
7 ZQ25-60 GB119 Cylindrical pin 6×18 4
8 ZQ25-66 ZQ25.1.1-8 Screw retainer pin 24
9 ZQ25-67 XYQ12.B-10 Set screw 2
10 ZQ25-130 ZQ25.2-3 Ramp 4
11 ZQ25-129 ZQ25.2-2 Main body 1
12 ZQ25-7 GB70 Hexagon socket head cap screw M12×25 34
13 ZQ25-128 ZQ25.2-1 Fore support seat 2
14 ZQ25-187 GB119 Cylindrical pin 5×25 1
15 ZQ25-184 ZQ25.1.8-5A knob 1
16 ZQ25-185 XYQ3C.B-10 spring 2
17 ZQ25-186 GB308 Steel ball Φ5 2
18 ZQ25-187 GB70 Hexagon socket head cap screw M10×30 12
19 ZQ25-146 ZQ25.2-10 Cover board 1
20 ZQ25-183 ZQ25.1.8-4A Knob shaft 1
21 ZQ25-132 ZQ25.2-5 Retainer pin 1
22 ZQ25-131 ZQ25.2-4 Jaw set bracket 1
23 ZQ25-136 GB1096 Ordinary parallel key 16×90 1
19
Model ZQ127/25Y Drill Pipe Power Tong
7.3.2 Backup tong tail assembly (Fig11. Table11)
Fig11. Backup tong tail assembly
Table11. Detailed table for Backup tong tail assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-152 GB70 Hexagon socket head cap screw M6×20 1
2 ZQ25-147 XYQ3C.Z-5 Locating disc 1
3 ZQ25-148 ZQ25.2-11 shaft（1） 1
4 ZQ25-152 GB70 Hexagon socket head cap screw M6×20 5
5 ZQ25-151 ZQ25.2-13 Gear cover 1
6 ZQ25-150 GB1235 O ring 50×3.1 1
7 ZQ25-149 ZQ25.2-12 Duplex gear 1
8 ZQ25-135 ZQ25.2-7 Tail handle 1
9 ZQ25-156 ZQ25.2-16 Cylinder sleeve 1
10 ZQ25-157 ZQ25.2-17 Rack plunger 1
11 ZQ25-137 GB93 Standard spring washer 16 4
12 ZQ25-138 GB5781 Hex head bolt M16×40 4
13 ZQ25-140 GB1235 O ring 45×3.1 4
14 ZQ25-141 GB1235 ring 45 2
15 ZQ25-142 GB1235 O ring 22×2.4 4
20
Model ZQ127/25Y Drill Pipe Power Tong
16 ZQ25-143 XYQ3C.B-21（1） Oil passage bolt（1） 2
17 ZQ25-206 XYQ3 B.B-10 Adapter 2
18 ZQ25-144 JB/ZQ4427 Hose adaptor 10Ⅱ-1400 2
19 ZQ25-139 ZQ25.2-8 Cylinder cover 2
20 ZQ25-145 ZQ25.2-9 Plunger 2
21 ZQ25-154 ZQ25.2-14 Stop screw 1
22 ZQ25-153 GB93 Standard spring washer 16 1
23 ZQ25-15 ZQ25.2-15 Tail seat 1
7.4 Fore guide pole assembly (Fig12. Table12)
Fig12. Fore guide pole assembly
Table12. Detailed table for Fore guide pole assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-164 ZQ25.3.1 Fore guide pole assembil 2
2 ZQ25-166 XYQ12.QD-04 Fore guide pole spring 2
3 ZQ25-165 XYQ12.QD-03B Fore guide pole 2
4 ZQ25-163 XYQ12.QD-01 Fore guide pole seat 2
5 ZQ25-168 GB91 Cotter pin 2.5×20 2
6 ZQ25-167 XYQ12.QD-05 Pin shaft 2
21
Model ZQ127/25Y Drill Pipe Power Tong
7.5 Back guide pole assembly (Fig13. Table13)
Fig13. Back guide pole assembly
Table13. Detailed table for Back guide pole assembly
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-175 ZQ25.4-1 Sleeve 1
2 ZQ25-170 ZQ25.4.1 Back guide pole sleeve 1
3 ZQ25-172 XYQ12.HD-06A Back guide pole spring 1
4 ZQ25-171 XYQ12.HD-03(1C) Back guide pole 1
5 ZQ25-169 XYQ12.HD-01 Back guide pole seat 1
6 ZQ25-174 GB91 Cotter pin 3.2×20 1
7 ZQ25-173 XYQ12.HD-06A Pin shaft 1
22
Model ZQ127/25Y Drill Pipe Power Tong
8 .Easy-damaged parts list
Item Purchase No. Part No. Part name and Description QTY
1 ZQ25-13 ZQ25.1-3 Centralizing roller shaft 37
2 ZQ25-14 XYQ12.Z-03 Centralizing roller 37
3 ZQ25-16 GB68 Slotted countersunk screw M5×10 79
4 ZQ25-33 GB1235 O ring 28×2.4 2
5 ZQ25-37 GB1235 O ring 24×2.4 8
6 ZQ25-40 GB1235 O ring 36×3.5 4
7 ZQ25-43 GB1235 O ring 32×3.5 2
8 ZQ25-45 GB1235 O ring 38×3.5 2
9 ZQ25-65 XYQ12.Z-01.12(2-3) die（2-3） Each for 24
10 ZQ25-72 XYQ12.Z-48 roller 16
11 ZQ25-73 XYQ12.Z-49 Pin shaft 16
12 ZQ25-77 GB1235 O ring 63×5.7 16
13 ZQ25-78 Roller Φ10×30 168
14 ZQ25-97 GB1235 O ring 40×3.1 2
15 ZQ25-99 GB1235 O ring 80×3.1 2
16 ZQ25-117 ZQ25.1.8-2 Friction disc 6
17 ZQ25-140 GB1235 O ring 45×3.1 8
18 ZQ25-142 GB1235 O ring 22×2.4 8
19 ZQ25-150 GB1235 O ring 50×3.1 2
23
