30/5/2020 PINTLE INJECTOR: Design of a pintle injector for 5000 N liquid rocket propellant engine
Liên kết khác [email protected] Bảng điều khiển Đăng xuất
PINTLE INJECTOR
This blog is about pintle injector used in Space X Falcon 9 rocket. As a part of my
Masters theisis, I have fabricated several pintle injectors and tested it in propulsion
lab. This blog is intended to simplify the efforts of rocket propulsion enthusiasists to
easily grasp and fabricated an injector for their rocket engine.
Sunday, January 15, 2017 I am very passionate about rockets and looking
forward to work in rocket propulsion research.
Design of a pintle injector for 5000 N liquid rocket propellant Unknown
engine View my complete profile
Posts
A 5000N engine with LOX anf Kerosine has been selected and a pintle
▼
▼ 17 (5)
injector has been designed to meet the requirements of this engine. The ►
► May (1)
combustion chamber pressure was 25 bar (2500000 Pa). The specific heat ratio
►
► Mar (1)
(K) was 1.16. Gas constant R was 704.8 J/Kg-K. Exit Pressure Pe was 1 bar.
►
► Feb (1)
The temperature at the combustion chamber was taken as 3141.07 K.
▼
▼ Jan (2)
Computer software for pintle injector
Thrust co-efficient was calculated using the below mentioned equation. design data
Design of a pintle injector for 5000 N
liquid rock...
►
► 16 (4)
Throat area of the Nozzle can be found out using:
pintleinjector.blogspot.com/2017/01/design-of-pintle-injector-for-5000-n.html 1/6
30/5/2020 PINTLE INJECTOR: Design of a pintle injector for 5000 N liquid rocket propellant engine
Now we have to find the characteristics velocity c* to know the mass flow
required for this 5000N engine.
The characteristic velocity, also called c-star or simply c*, is a figure of
thermochemical merit for a particular propellant and may be considered to be
indicative of the combustion efficiency.
Now mass flow rate can be found out from
The stoichiometric mixture ratio was taken for the calculation of propellant
flow rates. The stoichiometric oxidizer to fuel ratio for liquid kerosene and
liquid oxygen is 2.5.
pintleinjector.blogspot.com/2017/01/design-of-pintle-injector-for-5000-n.html 2/6
30/5/2020 PINTLE INJECTOR: Design of a pintle injector for 5000 N liquid rocket propellant engine
Oxidizer flow rate can be found out using:
Area required to inject the propellants at the above mentioned flow rates can
be found out from
Veleocity of fuel discharge is 19.09 m/s
Where Cd is the discharge co-efficient, discharge coefficient (also known as
coefficient of discharge) is the ratio of the actual discharge to the theoretical
discharge.
Discharge co-efficient of .7 was assumed as it was found experimentally for
the pintle injector design in one of the research papers. Density of kerosene at
15° was 806 kg/m3. Density of kerosene at -182.96° is 1141 kg/m3.
A reasonable pressure drop of 3 bar for the propellants was assumed.
pintleinjector.blogspot.com/2017/01/design-of-pintle-injector-for-5000-n.html 3/6
30/5/2020 PINTLE INJECTOR: Design of a pintle injector for 5000 N liquid rocket propellant engine
Corresponding fuel injection velocity is found out in the last equation
mentioend above.
Corresponding oxidizer injection velocity can be found out using
1.1 PINTLE DESIGN
As per the design procedure mentioned by Min son et all, a pintle diameter of
20 mm was chosen.
Now, the gap between pintle’s slanted surface and annular casing has to be
determined. This area is the area of the cylinder with the diameter of pintle
pintle. Area of that Oxidizer discharge gap is
pintleinjector.blogspot.com/2017/01/design-of-pintle-injector-for-5000-n.html 4/6
30/5/2020 PINTLE INJECTOR: Design of a pintle injector for 5000 N liquid rocket propellant engine
Fuel discharge gap-"annular gap" between two concentric circles is 0.43 mm.
Drawing of a pintle injector dimensions for 5000 N engine using LOX and kerosine
Cut away view of pintle injector with two inlets marked on the right side
Posted by Unknown at 3:55 AM
pintleinjector.blogspot.com/2017/01/design-of-pintle-injector-for-5000-n.html 5/6
30/5/2020 PINTLE INJECTOR: Design of a pintle injector for 5000 N liquid rocket propellant engine
No comments:
Post a Comment
Enter your comment...
Comment as: tridinhquoc@gm Sign out
Publish Preview Notify me
Newer Post Home Older Post
Subscribe to: Post Comments (Atom)
Total Pageviews
18,599
Text is available under the Creative Commons Attribution-ShareAlike License.. Simple theme. Theme images by gaffera. Powered by Blogger.
pintleinjector.blogspot.com/2017/01/design-of-pintle-injector-for-5000-n.html 6/6
