Date: __________ Init.
: __________
Settings for Unisab III 1.03
Customer:
End user:
Compressor shop no.:
Local compr. no. :
ROC no.:
Order no.:
Plant type:
Compressor type:
Software version/date:
Set up >Compr. Control Set up >Sequencing
No Function Setting No Function Setting
1 Mode 1 Start no
2 Control On 2 System no
3 Capacity controller 3 System controller
4 Auto Start
5 Auto Stop Set up > Multisab
6 Cold Store 1 Parallel offset
7 Climate Compensation
8 Multisab master
Setup> Configuration>Calibrate
>Press transducer >Process out Temp. >Position >Motor Freq
Suction Adjust Process out Adj Cap. Pos Motor Freq
Discharge Adjust Cap. Zero Ad Frq. Zero Adj
Oil Adjust Cap. 100 Adj Freq. 100 Adj
Diff./Imed Adjust Vi Position
Oil. Adjust Vi. Zero Adj
Eco Adjust Vi. 100 Adj
Page 1/4
Settings for Unisab III 1.03
Setup>Configuration
>Drive >Oil system >Communication
No. Function Setting No. Function Setting No. Function Setting
1 Motor range Amp 1 Oil pump 1 Compressor
2 Motor range KW 2 Full Flow Pump 2 Baud rate
3 Motor nom kW 3 Oil Cooling 3 Profibus
4 Display 4 Oil controller 4 Profi. node no.
5 Motor input signal 5 Water Cooling 5 Profi. baud rate
6 Rotatune 6 Oil Rectifier 6 GSD file no.
7 Motor rpm min. 7 Sep.Vel.Ref
8 Motor rpm max. 8 Sep.Vel.CR
>Compressor block
No. Function Setting >Measuring
1 Compressor Type No. Function Setting
2 Swept Volume 1 Press./Temp.
3 Volume Ratio 2 Pressure range
4 Vi Low Range 3 Low Suct. Press
5 Vi Mode % 4 Capacity signal
6 Mech. Zero
7 Manual Zero >Aux output >Dig. In Via Profibus
8 Booster No. Function Setting No. Function
9 Economizer 1 Activate when 1 Dig. Input 1
10 Eco Low Cap. 2 Signal Low 2 Dig. Input 2
11 Neutral zone 3 Signal High 3 Dig. Input 3
12 Eco High Suction 4 Dig. Input 4
13 Unloading >External (user 1) input 5 Dig. Input 5
14 Unload assist 1 Function 6 Dig. Input 6
15 Cap.decr.assist rate 2 4 mA 7 Dig. Input 7
16 Volume dead band 3 20 mA 8 Dig. Input 8
9 Dig. Input 9
>Plant 10 Dig. Input 10
No. Function Setting 11 Dig. Input 11
1 Refrigerant 12 Dig. Input 12
2 Compressor Setup>Session 13 Dig. input 13
3 Start 1 Language 14 Dig. Input 14
4 System
Common
5
Evap/Cond
6 HP on Two Stage
7 High Limit >Factory reset
8 Take Over No. Function Setting
9 COP Active 1 Factory reset
10 Chiller
11 Flow factor
12 Liquid subcool
Setup>Configuration>R000
Temp °C/R Press Bar Temp °C/R Press Bar Temp °C/R Press Bar
-90 -30 30
-85 -25 35
-80 -20 40
-75 -15 45
-70 -10 50
-65 -05 55
-60 00 60
-55 05 65
-50 10 70
-45 15 75
-40 20 80
-35 25
Page 2/4
Settings for Unisab III 1.03
Setup>Timers>Timers Setup (1)
No. Function Setting No. Function Setting No. Function Setting
Oil Pressure Low
45/300/25
(*S)
01 Start-Start Delay 13 25 Oil Rect. Start
Oil Pressure Low
60
(*R)
Filter diff high (*S) 300
02 Stop-Start Delay 14 26 Oil Rect. Pause
Oil press high (*R) 20
03 Start Delay 15 Oil Temp Low 300 27 Oil Rect. Disable
16 300
04 Stop Delay Oil Temp High 28 Start HP
0
300
05 Suction Ramp 17 Superheat Low 29 No Chiller 10
15
Slide Max (*S) 18
06 Superheat High 300 30 Cap. Negative (*S)
Delay Up (*R)
Pre lubrication 10/60/0/6/
Disch Press
07 (*S) 50/0 19 300 31 Start Unload (*S)
O/load
Delay Down (*R)
Oil Flow 600/90/60/
08 (*S) 120/600/0 20 Current Overload 300 32 Low suct. press
Transfer max (*R)
Oil Flow Delay
50/0/20/10
(*S)
09 21 Motor Start 33 Lub Pressure (*S) 145
Take Over Delay
300
(*R)
No Oil Flow 10/2/6/120
(*S) /30 22 PMS Feedback
10 34 Vi pause (*S) 60
Interm Press Low
20
(*R)
Lub time/flow F.F. Pump Oil Log Shutdown
60/300 35 60
(*S) Start(*S) (*S)
11
Filter Diff High 23 Oil Cool On
300 36 Low Oil Flow (*S) 180
(*R) (*R)
Diff press OK (*S) 60 Oil Pump Start(*S) 37 Oil Cir. Alm (*S) 600
12 24 Oil Cir. Shutdown
Total unload (*R) Oil Return (*R) 38 900
(*S)
39 SSSTV delay
Setup>Timers>P Band Factor Setup>Timers>Transfer Setup>Timers>Take Over
(1) (1) (1)
Delay Up (*R) Factor Down (*R) Factor Up (*R)
Delay Down (*R) Zone (*R) Factor Start (*R)
Start Delay Zone (*R)
Stop Delay
Setup>Service>Maintenance
Estimated compressor main service
Hour counter
Time to next main service C
Time to next part service B
Time to next part service A
Page 3/4
Settings for Unisab III 1.03
Control values>
Alarm-/Shutdown Limits & High High Low Low SP SP NZ PB T. T. MIN RUN
Regulator Settings (1) Shut Alarm Alarm Shut No. 1 No. 2 Integ. Diff. PULS TIME
down down
Suction>Suction pressure
[ºC/R]
Suction>Suction superheat
Discharge>Disch. pressure
[ºC/R]
Discharge>Disch.
Temperature
Discharge>Disch. Superheat
Oil>Oil pressure
Oil>Oil filter pressure
(*S)
Oil>Oil temperature
Oil>Oil separator temperature
(*S)
Motor>Motor current
Motor>Motor Power
Capacity>Capacity
(*S)
Capacity>Vi Position
(*S)
Process temp>Process out
temp
User> User input 1
Intermediate>Interm. pres.
[ºC/R] (*R)
Intermediate>Interm.
temperature (*R)
Notes:
(*S) = Screw, (*R) = Reciprocating
(1) The value(s) will be changed to factory settings by a “Factory reset”.
Page 4/4
