G3516 Engine Electronic Ignition System 4EK00001-UP(SEBP2185 - 78) - Documentation Page 1 of 3
Shutdown SIS
Previous Screen
Product: GAS ENGINE
Model: G3516 GAS ENGINE 4EK02191
Configuration: G3516 Engine Electronic Ignition System 4EK00001-UP
Disassembly and Assembly
G3500 Engines
Media Number -SENR6419-13 Publication Date -01/08/2013 Date Updated -08/08/2013
i03867080
Camshaft Bearings - Install
SMCS - 1211-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
6V-4077 Camshaft Bearing Tool Group 1
125-2739 (1)
Bearing Pilot 1
A
125-2740 (1)
Back Up Plate 1
125-2741 (1)
Bearing Sleeve 1
B 8S-2241 Camshaft Bearing Tool Group 1
C 5P-5247 Hydraulic Puller 1
D 8H-0684 Ratchet Wrench 1
(1)
Alternate Tooling for camshaft bearings with a large diameter
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2016
G3516 Engine Electronic Ignition System 4EK00001-UP(SEBP2185 - 78) - Documentation Page 2 of 3
Illustration 1 g00578338
Typical example
1. Install camshaft bearing (1) on Tooling (A) .
Note: Tooling (B) can be used to install the camshaft bearings when the flywheel housing and
the front housing have been removed.
Illustration 2 g02108639
Rear View
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2016
G3516 Engine Electronic Ignition System 4EK00001-UP(SEBP2185 - 78) - Documentation Page 3 of 3
(X) Location of camshaft bearing joints
(Y) Location of oil holes
2. Position camshaft bearing (1) and Tooling (A) in the bore.
Note: The camshaft bearing joint must be on the horizontal centerline of the bore. The upper oil
hole must be 20 ± 5 degrees above the horizontal centerline of the bore. The lower oil hole of
the camshaft bearing must be 20 ± 5 degrees below the horizontal centerline of the bore. The
camshaft bearing joints must face the inside of the cylinder block.
Illustration 3 g00578349
3. Install Tooling (C) on Tooling (A) and pull the camshaft bearing into the bore.
Note: Tooling (D) can be used in place of Tooling (C) .
4. Check the bore of the camshaft bearing after installation. The bore must be 86.00 ± 0.06 mm
(3.385 ± 0.002 inch).
End By: Install the camshafts. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2016 Caterpillar Inc. Sat Dec 3 12:53:23 UTC+0330 2016
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2016
