SAFETY DATA SHEET
NALCO® 7330
SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
Product name : NALCO® 7330
Other means of identification : Not applicable
Recommended use : BIOCIDE
Restrictions on use : Refer to available product literature or ask your local Sales
Representative for restrictions on use and dose limits.
Company : Nalco Company
1601 W. Diehl Road
Naperville, Illinois 60563-1198
USA
TEL: (630)305-1000
Emergency telephone : (800) 424-9300 (24 Hours) CHEMTREC
number
Issuing date : 08/21/2014
SECTION 2. HAZARDS IDENTIFICATION
GHS Classification
Acute toxicity (Inhalation) : Category 4
Skin corrosion : Category 1A
Serious eye damage : Category 1
Skin sensitization : Category 1
GHS Label element
Hazard pictograms :
Signal word : Danger
Hazard statements : Causes severe skin burns and eye damage.
May cause an allergic skin reaction.
Harmful if inhaled.
Precautionary statements : Prevention:
Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray. Wash skin
thoroughly after handling. Use only outdoors or in a well-ventilated
area. Contaminated work clothing should not be allowed out of the
workplace. Wear protective gloves/ protective clothing/ eye
protection/ face protection.
Response:
IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. IF ON
SKIN (or hair): Remove/ Take off immediately all contaminated
clothing. Rinse skin with water/ shower. IF INHALED: Remove
victim to fresh air and keep at rest in a position comfortable for
breathing. IF IN EYES: Rinse cautiously with water for several
1 / 11
SAFETY DATA SHEET
NALCO® 7330
minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. Immediately call a POISON CENTER or doctor/
physician. If skin irritation or rash occurs: Get medical advice/
attention. Wash contaminated clothing before reuse.
Storage:
Store locked up.
Disposal:
Dispose of contents/ container to an approved waste disposal
plant.
Other hazards : None known.
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Pure substance/mixture : Mixture
Chemical Name CAS-No. Concentration: (%)
Magnesium Nitrate 10377-60-3 1-5
5-Chloro-2-Methyl-4-Isothiazolin-3-one 26172-55-4 1-5
2-Methyl-4-Isothiazolin-3-one 2682-20-4 0.1 - 1
SECTION 4. FIRST AID MEASURES
In case of eye contact : Rinse immediately with plenty of water, also under the eyelids, for at
least 15 minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. Get medical attention immediately.
In case of skin contact : Wash off immediately with plenty of water for at least 15 minutes.
Use a mild soap if available. Wash clothing before reuse.
Thoroughly clean shoes before reuse. Get medical attention
immediately.
If swallowed : Rinse mouth with water. Do NOT induce vomiting. Never give
anything by mouth to an unconscious person. Get medical attention
immediately.
If inhaled : Remove to fresh air. Treat symptomatically. Get medical attention.
Protection of first-aiders : In event of emergency assess the danger before taking action. Do
not put yourself at risk of injury. If in doubt, contact emergency
responders.Use personal protective equipment as required.
Notes to physician : Treat symptomatically.
See toxicological information (Section 11)
SECTION 5. FIREFIGHTING MEASURES
Suitable extinguishing media : Use extinguishing measures that are appropriate to local
circumstances and the surrounding environment.
Unsuitable extinguishing : None known.
media
Specific hazards during : Not flammable or combustible.
firefighting
Hazardous combustion : Carbon oxides
2 / 11
SAFETY DATA SHEET
NALCO® 7330
products
Special protective equipment : Use personal protective equipment.
for firefighters
Specific extinguishing : Fire residues and contaminated fire extinguishing water must
methods be disposed of in accordance with local regulations. In the
event of fire and/or explosion do not breathe fumes.
SECTION 6. ACCIDENTAL RELEASE MEASURES
Personal precautions, : Ensure adequate ventilation. Keep people away from and upwind of
protective equipment and spill/leak. Avoid inhalation, ingestion and contact with skin and eyes.
emergency procedures When workers are facing concentrations above the exposure limit
they must use appropriate certified respirators. Ensure clean-up is
conducted by trained personnel only. Refer to protective measures
listed in sections 7 and 8.
Environmental precautions : Do not allow contact with soil, surface or ground water.
Methods and materials for : Stop leak if safe to do so. Contain spillage, and then collect with
containment and cleaning up non-combustible absorbent material, (e.g. sand, earth,
diatomaceous earth, vermiculite) and place in container for disposal
according to local / national regulations (see section 13). Flush away
traces with water. For large spills, dike spilled material or otherwise
contain material to ensure runoff does not reach a waterway.
SECTION 7. HANDLING AND STORAGE
Advice on safe handling : Do not ingest. Do not breathe dust/ fume/ gas/ mist/ vapours/ spray.
Do not get in eyes, on skin, or on clothing. Wash hands thoroughly
after handling. Use only with adequate ventilation.
Conditions for safe storage : Keep out of reach of children. Keep container tightly closed. Store in
suitable labeled containers.
Suitable material : HDPE (high density polyethylene), PTFE, PVC, Polyvinylidene
difluoride, Polypropylene, Plexiglass, Perfluoroelastomer, CPVC
(rigid), Buna-N
Keep in properly labelled containers.
Unsuitable material : The following compatibility data is suggested based on similar
product data and/or industry experience: Shipping and long term
storage compatibility with construction materials can vary; we
therefore recommend that compatibility is tested prior to use.
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Components with workplace control parameters
Contains no substances with occupational exposure limit values.
Engineering measures : Effective exhaust ventilation system Maintain air concentrations
below occupational exposure standards.
Personal protective equipment
3 / 11
SAFETY DATA SHEET
NALCO® 7330
Eye protection : Safety goggles
Face-shield
Hand protection : Wear the following personal protective equipment:
Standard glove type.
Gloves should be discarded and replaced if there is any indication of
degradation or chemical breakthrough.
Skin protection : Personal protective equipment comprising: suitable protective
gloves, safety goggles and protective clothing
Respiratory protection : When workers are facing concentrations above the exposure limit
they must use appropriate certified respirators.
Hygiene measures : Handle in accordance with good industrial hygiene and safety
practice. Remove and wash contaminated clothing before re-use.
Wash face, hands and any exposed skin thoroughly after handling.
Provide suitable facilities for quick drenching or flushing of the eyes
and body in case of contact or splash hazard.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance : Liquid
Colour : colourless
Odour : Mild
Flash point : > 93.3 °C
Estimated
pH : 2.0 - 5.0, 100 %
(25 °C)
Odour Threshold : No data available
Melting point/freezing point : FREEZING POINT: -4 °C, ASTM D-1177
Initial boiling point and boiling : 100 °C Method: ASTM D 86
range
Evaporation rate : No data available
Flammability (solid, gas) : No data available
Upper explosion limit : No data available
Lower explosion limit : No data available
Vapour pressure : similar to water
Relative vapour density : No data available
Relative density : 1.026 (25 °C)
Density : 8.5 lb/gal
Water solubility : completely soluble
Solubility in other solvents : No data available
Partition coefficient: n- : No data available
octanol/water
Auto-ignition temperature : No data available
Thermal decomposition : Carbon oxides
Viscosity, dynamic : No data available
4 / 11
SAFETY DATA SHEET
NALCO® 7330
Viscosity, kinematic : 3 mm2/s (20 °C)
VOC : 0.80 %
8.39 g/l
SECTION 10. STABILITY AND REACTIVITY
Chemical stability : Stable under normal conditions.
Possibility of hazardous : No dangerous reaction known under conditions of normal use.
reactions
Conditions to avoid : None known.
Incompatible materials : Contact with strong oxidizers (e.g. chlorine, peroxides, chromates,
nitric acid, perchlorate, concentrated oxygen, permanganate) may
generate heat, fires, explosions and/or toxic vapors.
Hazardous decomposition : Oxides of carbon
products Oxides of nitrogen
Oxides of sulfur
HCl
SECTION 11. TOXICOLOGICAL INFORMATION
Information on likely routes of : Inhalation, Eye contact, Skin contact
exposure
Potential Health Effects
Eyes : Causes serious eye damage.
Skin : Causes severe skin burns. May cause allergic skin reaction.
Ingestion : Causes digestive tract burns.
Inhalation : Harmful if inhaled. May cause nose, throat, and lung irritation.
Chronic Exposure : Health injuries are not known or expected under normal use.
Experience with human exposure
Eye contact : Redness, Pain, Corrosion
Skin contact : Redness, Pain, Irritation, Corrosion, Allergic reactions
Ingestion : Corrosion, Abdominal pain
Inhalation : Respiratory irritation, Cough
Toxicity
Product
Acute oral toxicity : Acute toxicity estimate : > 5,000 mg/kg
5 / 11
SAFETY DATA SHEET
NALCO® 7330
Acute inhalation toxicity : LC50 Rat: 13.7 mg/l
Exposure time: 4 hrs
Test substance: Product
Acute dermal toxicity : No data available
Skin corrosion/irritation : No data available
Serious eye damage/eye : No data available
irritation
Respiratory or skin : No data available
sensitization
Carcinogenicity : No data available
Reproductive effects : No data available
Germ cell mutagenicity : No data available
Teratogenicity : No data available
STOT - single exposure : No data available
STOT - repeated exposure : No data available
Aspiration toxicity : No data available
Components
Acute dermal toxicity : Magnesium Nitrate
LD50 Rat: > 5,000 mg/kg
5-Chloro-2-Methyl-4-Isothiazolin-3-one
LD50 Rabbit: 200 mg/kg
2-Methyl-4-Isothiazolin-3-one
LD50 Rabbit: 200 mg/kg
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
Environmental Effects : Very toxic to aquatic life.
Product
Toxicity to fish : LC50 Sheepshead Minnow: 32.000 mg/l
Exposure time: 96 hrs
Test substance: Product
LC50 Bluegill Sunfish: 18.67 mg/l
Exposure time: 96 hrs
Test substance: Product
LC50 Rainbow Trout: 12.67 mg/l
6 / 11
SAFETY DATA SHEET
NALCO® 7330
Exposure time: 96 hrs
Test substance: Product
LC50 Inland Silverside: 16.62 mg/l
Exposure time: 96 hrs
Test substance: Product
LC50 Sheepshead Minnow: 0.3 mg/l
Exposure time: 96 hrs
Test substance: Active Substance
Toxicity to daphnia and other : LC50 Mysid Shrimp (Mysidopsis bahia): 18.000 mg/l
aquatic invertebrates Exposure time: 96 hrs
Test substance: Product
LC50 Ceriodaphnia dubia: 13 mg/l
Exposure time: 48 hrs
Test substance: Product
LC50 Daphnia magna: 8.7 - 12 mg/l
Exposure time: 48 hrs
Test substance: Product (estimated)
LC50 Blue Mussel: 865 mg/l
Exposure time: 48 hrs
Test substance: Product (estimated)
LC50 American Oyster: 1,730 mg/l
Exposure time: 48 hrs
Test substance: Product (estimated)
Toxicity to algae : EC50 Marine Algae (Skeletonema costatum): 0.003 mg/l
Exposure time: 72 h
Test substance: Active Substance
EC50 Green Algae (Pseudokirchneriella subcapitata,
previously Selenastrum capricornutum): 0.018 mg/l
Exposure time: 72 h
Test substance: Active Substance
Toxicity to terrestrial : LC50 Pekin Duck: > 100 mg/kg
organisms Exposure time: 8 Days
Test substance: Active Substance
LC50 Bobwhite Quail: 85 mg/kg
Exposure time: 21 Days
Test substance: Active Substance
LC50 Bobwhite Quail: > 60 mg/kg
Exposure time: 8 Days
Test substance: Active Substance
Persistence and degradability
The degradation of the major active substance begins with ring opening and elimination of chloride ion.
Degradation leads to the formation of a variety of small organic acids, methylamine, carbon dioxide
and elemental sulfur. The half life of each active substance is dependent upon the initial concentration.
7 / 11
SAFETY DATA SHEET
NALCO® 7330
Total Organic Carbon (TOC) : 7,850 mg/l
Chemical Oxygen Demand (COD): 20,000 mg/l
Biochemical Oxygen Demand (BOD):
Incubation Period Value Test Descriptor
20 mg/l
Mobility
The environmental fate was estimated using a level III fugacity model embedded in the EPI (estimation
program interface) Suite TM, provided by the US EPA. The model assumes a steady state condition
between the total input and output. The level III model does not require equilibrium between the
defined media. The information provided is intended to give the user a general estimate of the
environmental fate of this product under the defined conditions of the models.
If released into the environment this material is expected to distribute to the air, water and
soil/sediment in the approximate respective percentages;
Air : <5%
Water : 30 - 50%
Soil : 50 - 70%
The portion in water is expected to be soluble or dispersible.
Bioaccumulative potential
This preparation or material is not expected to bioaccumulate.
Other information
No data available
SECTION 13. DISPOSAL CONSIDERATIONS
If this product becomes a waste, it could meet the criteria of a hazardous waste as defined by the
Resource Conservation and Recovery Act (RCRA) 40 CFR 261. Before disposal, it should be
determined if the waste meets the criteria of a hazardous waste.
Disposal methods : The product should not be allowed to enter drains, water
courses or the soil. Where possible recycling is preferred to
disposal or incineration. If recycling is not practicable, dispose
of in compliance with local regulations. Dispose of wastes in
an approved waste disposal facility.
Disposal considerations : Dispose of as unused product. Empty containers should be
taken to an approved waste handling site for recycling or
disposal. Do not re-use empty containers.
SECTION 14. TRANSPORT INFORMATION
The shipper/consignor/sender is responsible to ensure that the packaging, labeling, and markings are
in compliance with the selected mode of transport.
Land transport (DOT)
The presence of an RQ component (Reportable Quantity for U.S. EPA and DOT) in this product
causes it to be regulated with an additional description of RQ for road, or as a class 9 for road and air,
ONLY when the net weight in the package exceeds the calculated RQ for the product.
Proper shipping name : CORROSIVE LIQUID, ACIDIC, ORGANIC, N.O.S.
8 / 11
SAFETY DATA SHEET
NALCO® 7330
Technical name(s) : ISOTHIAZOLINONE MICROBIOCIDE
UN/ID No. : UN 3265
Transport hazard class(es) : 8
Packing group : II
Reportable Quantity (per : 132,270 lbs
package)
RQ Component : CUPRIC NITRATE
Air transport (IATA)
The presence of an RQ component (Reportable Quantity for U.S. EPA and DOT) in this product
causes it to be regulated with an additional description of RQ for road, or as a class 9 for road and air,
ONLY when the net weight in the package exceeds the calculated RQ for the product.
Proper shipping name : CORROSIVE LIQUID, ACIDIC, ORGANIC, N.O.S.
Technical name(s) : ISOTHIAZOLINONE MICROBIOCIDE
UN/ID No. : UN 3265
Transport hazard class(es) : 8
Packing group : II
Reportable Quantity (per : 132,270 lbs
package)
RQ Component : CUPRIC NITRATE
Sea transport (IMDG/IMO)
Proper shipping name : CORROSIVE LIQUID, ACIDIC, ORGANIC, N.O.S.
Technical name(s) : ISOTHIAZOLINONE MICROBIOCIDE
UN/ID No. : UN 3265
Transport hazard class(es) : 8
Packing group : II
*Marine pollutant : ISOTHIAZOLINONE MICROBIOCIDE
*Note: This product is regulated as a Marine Pollutant when shipped by Rail, Highway (in bulk
quantities), or Air (if no other hazard class applies), and when shipped by water in all quantities.
SECTION 15. REGULATORY INFORMATION
EPA Reg. No. : 1706-153
EPCRA - Emergency Planning and Community Right-to-Know Act
CERCLA Reportable Quantity
Components CAS-No. Component RQ (lbs) Calculated product RQ
(lbs)
Cupric Nitrate 3251-23-8 100 132275
SARA 304 Extremely Hazardous Substances Reportable Quantity
This material does not contain any components with a section 304 EHS RQ.
SARA 311/312 Hazards : Acute Health Hazard
SARA 302 : No chemicals in this material are subject to the reporting requirements
of SARA Title III, Section 302.
SARA 313 : This material does not contain any chemical components with known
CAS numbers that exceed the threshold (De Minimis) reporting levels
established by SARA Title III, Section 313.
9 / 11
SAFETY DATA SHEET
NALCO® 7330
California Prop 65
This product does not contain any chemicals known to State of California to cause cancer, birth
defects, or any other reproductive harm.
INTERNATIONAL CHEMICAL CONTROL LAWS :
TOXIC SUBSTANCES CONTROL ACT (TSCA)
This product is exempted under TSCA and regulated under FIFRA. The inerts are on the Inventory
List.
CANADIAN ENVIRONMENTAL PROTECTION ACT (CEPA)
Substances regulated under the Pest Control Products Act are exempt from CEPA New Substance
Notification requirements.
AUSTRALIA
All substances in this product comply with the National Industrial Chemicals Notification & Assessment
Scheme (NICNAS).
CHINA
All substances in this product comply with the Provisions on the Environmental Administration of New
Chemical Substances and are listed on or exempt from the Inventory of Existing Chemical Substances
China (IECSC).
EUROPE
The substances in this preparation have been reviewed for compliance with the EINECS or ELINCS
inventories.
JAPAN
All substances in this product comply with the Law Regulating the Manufacture and Importation Of
Chemical Substances and are listed on the Existing and New Chemical Substances list (ENCS).
KOREA
All substances in this product comply with the Toxic Chemical Control Law (TCCL) and are listed on
the Existing Chemicals List (ECL)
NEW ZEALAND
All substances in this product comply with the Hazardous Substances and New Organisms (HSNO)
Act 1996,and are listed on or are exempt from the New Zealand Inventory of Chemicals.
PHILIPPINES
All substances in this product comply with the Republic Act 6969 (RA 6969) and are listed on the
Philippines Inventory of Chemicals & Chemical Substances (PICCS).
SECTION 16. OTHER INFORMATION
10 / 11
SAFETY DATA SHEET
NALCO® 7330
NFPA: HMIS III:
Flammability
HEALTH 3
0
Instability
Health
3 0 FLAMMABILITY 0
PHYSICAL HAZARD 0
0 = not significant, 1 =Slight,
2 = Moderate, 3 = High
Special hazard. 4 = Extreme, * = Chronic
Revision Date : 08/21/2014
Version Number : 1.0
Prepared By : Regulatory Affairs
REVISED INFORMATION: Significant changes to regulatory or health information for this revision
is indicated by a bar in the left-hand margin of the SDS.
The information provided in this Safety Data Sheet is correct to the best of our knowledge,
information and belief at the date of its publication. The information given is designed only as a
guidance for safe handling, use, processing, storage, transportation, disposal and release and is
not to be considered a warranty or quality specification. The information relates only to the specific
material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
For additional copies of an MSDS visit www.nalco.com and request access.
11 / 11