LM2901/ LM2901A/ LM2903/ LM2903A

DUAL AND QUAD DIFFERENTIAL COMPARATORS

Description Pin Assignments

The LM2901/2903 series comparators consist of four and two
independent precision voltage comparators with very low input offset
voltage specification. They are designed to operate from a single
(Top View)
power supply over a wide range of voltages; however operation from
split power supplies is also possible. They offer low power supply 1OUT 1 8 VCC
current independent of the magnitude of the power supply voltage. 1IN- 2 - 7 2OUT
1
3 6

+
1IN+ - 2IN-
The LM2901/2903 series comparators are designed to directly 2

+
interface with TTL and CMOS. When operating from both plus and GND 4 5 2IN+
minus power supplies, the LM2901/2903 series comparators will
directly interface with MOS logic where their low power drain is a SO-8/TSSOP-8/MSOP-8
distinct advantage over standard comparators. LM2903/ LM2903A

The dual devices are available in SO-8, TSSOP-8, and MSOP-8, and
the quad devices available in SO-14 and TSSOP-14 with industry (Top View)
standard pinouts. Both use green mold compound as standard.
1OUT 1 14 3OUT
Features 2OUT 2 13 4OUT
VCC 3 12 GND
• Wide Power Supply Range:
 Single Supply: 2V to 36V 2IN- 4 - 11 4IN+

+
2 4
 Dual Supplies: ±1.0V to ±18V 5 - 10 4IN-

+
2IN+
• Very Low Supply Current Drain—Independent of Supply Voltage 1IN- 6 - 9 3IN+

+
 LM2903: 0.6mA 1 3
1IN+ 7 - 8

+
3IN-
 LM2901: 0.9mA
• Low Input Bias Current: 25nA
• Low Input Offset Current: ±5nA SO-14/TSSOP-14
• Typical Offset Voltage: LM2901/ LM2901A
 Non-A Device: 2mV
 A Device: 1mV
• Common-Mode Input Voltage Range Includes Ground
• Differential Input Voltage Range Equal to the Power Supply
Voltage
• Low Output Saturation Voltage:
 LM2903: 200mV at 4mA
 LM2901: 100mV at 4mA
• Output Voltage Compatible with TTL, MOS and CMOS
• Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
• Halogen and Antimony Free. “Green” Device (Note 3)

Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant.
2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and
Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.

LM2901/ LM2901A/ LM2903/ LM2903A 1 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Schematic Diagram
V CC

Q2 Q3
+INPUT Q1 Q4

OUTPUT
-INPUT Q8

Q7

Q5 Q6

Functional Block Diagram of LM2901/2901A/2903/2903A

(Each Comparator)

Pin Descriptions
LM2901, LM2901A
Pin Name Pin # Function
1OUT 1 Channel 1 Output
2OUT 2 Channel 2 Output
VCC 3 Chip Supply Voltage
2IN- 4 Channel 2 Inverting Input
2IN+ 5 Channel 2 Non-Inverting Input
1IN- 6 Channel 1 Inverting Input
1IN+ 7 Channel 1 Non-Inverting Input
3IN- 8 Channel 3 Inverting Input
3IN+ 9 Channel 3 Non-Inverting Input
4IN- 10 Channel 4 Inverting Input
4IN+ 11 Channel 4 Non-Inverting Input
GND 12 Ground
4OUT 13 Channel 4 Output
3OUT 14 Channel 3 Output
LM2903, LM2903A
1OUT 1 Channel 1 Output
1IN- 2 Channel 1 Inverting Input
1IN+ 3 Channel 1 Non-Inverting Input
GND 4 Ground
2IN+ 5 Channel 2 Non-Inverting Input
2IN- 6 Channel 2 Inverting Input
2OUT 7 Channel 2 Output
VCC 8 Chip Supply Voltage

LM2901/ LM2901A/ LM2903/ LM2903A 2 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Absolute Maximum Ratings (Note 4) (@TA = +25°C, unless otherwise specified.)

Symbol Parameter Rating Unit
VCC Supply Voltage 36 V
VID Differential Input Voltage 36 V
VIN Input Voltage -0.3 to +36 V
IIN Input Current (VIN < -0.3V) 50 mA
VO Output Voltage 36 V
IO Output Current 20 mA
— Duration of Output Short Circuit to Ground (Note 5) Unlimited —
SO-8 110
MSOP-8 160
Package Thermal Impedance
θJA TSSOP-8 185 °C/W
(Note 6)
SO-14 100
TSSOP-14 129
SO-8 8.5
MSOP-8 25
Package Thermal Impedance
θJC TSSOP-8 17 °C/W
(Note 6)
SO-14 16
TSSOP-14 6.3
TA Operating Temperature Range -40 to +125 °C
TJ Operating Junction Temperature 150 °C
TST Storage Temperature Range -65 to +150 °C
TLEAD Lead Temperature (Soldering, 10 seconds) 260 °C
Human Body Mode ESD Protection (Note 7) 500
ESD V
Machine Mode ESD Protection 100
Notes: 4. Stresses beyond those listed under Absolute Maximum Ratings can cause permanent damage to the device. These are stress ratings only; functional
operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to
absolute-maximum-rated conditions for extended periods can affect device reliability.
5. Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
6. Maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is
PD = (TJ(MAX) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
7. Human body model, 1.5kΩ in series with 100pF.

LM2901/ LM2901A/ LM2903/ LM2903A 3 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Electrical Characteristics (Notes 8 & 9) (@VCC = 5.0V, GND = 0V, TA = +25°C, unless otherwise specified.)
LM2901, LM2901A
Parameter Conditions TA Min Typ Max Unit

VIC = VCMR Min, TA = +25°C — 2 7

Non-A Device
VO = 1.4V, Full Range — — 15
VIO Input Offset Voltage mV
VCC = 5V to 30V TA = +25°C — 1 2
A-Suffix Device
(Note 10) Full Range — — 4
IIN+ or IIN− with OUT in Linear Range, TA = +25°C — 25 250
IB Input Bias Current nA
VCM = 0V (Note 11) Full Range — — 500
TA = +25°C — 5 50
IIO Input Offset Current IIN+ - IIN−, VCM = 0V nA
Full Range — — 200
0 to
TA = +25°C — —
Input Common-Mode VCC -1.5
VCMR VCC = 30V (Note 12) V
Voltage Range 0 to
Full Range — —
VCC-2
TA = +25°C — 1.2 2.5
VCC = 30V
Supply Current RL = ∞ on Full Range — — 3.5
ICC mA
(Four Comparators) Quad Channels TA = +25°C — 0.9 2
VCC = 5V
Full Range — — 3.0
VCC = 15V, VOUT = 1V to 11V,
AV Voltage Gain TA = +25°C 50 200 — V/mV
RL ≥ 15kΩ,
VIN = TTL Logic Swing, VREF = 1.4V,
— Large Signal Response time TA = +25°C — 300 — ns
VRL = 5V, RL = 5.1kΩ
— Response Time VRL = 5V, RL = 5.1kΩ (Note 13) TA = +25°C — 1.3 — µs
IO(SINK) Output Sink Current VIN− = 1V, VIN+ = 0, VO ≤ 1.5V TA = +25°C 6 16 — mA
TA = +25°C — 100 400
VSAT Saturation Voltage VIN− = 1V, VIN+ = 0, ISINK ≤ 4mA mV
Full Range — — 700
VIN− = 0V, VIN+ = 1, VO = 5V TA = +25°C — 0.1 — nA
IO(LEAK) Output Leakage Current
VIN− = 0V, VIN+ = 1, VO = 30V Full Range — — 1 µA
VID Differential Input Voltage All VIN ≥0V (or V- if used) (Note 14) Full Range — — 36 V
Notes: 8. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
9. All limits are guaranteed by testing or statistical analysis. Limits over the full temperature are guaranteed by design, but not tested in production.
10. VO ≅ 1.4V, RS = 0Ω with VCC from 5V to 30V;
11. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the input lines.
12. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (@ +25°C). The upper end of the
common-mode voltage range is VCC -1.5V (@ +25°C), but either or both inputs can go to +36V without damage, independent of the magnitude of VCC.
13. The response time specified is for a 100mV step input with 5mV overdrive. For larger overdrive signals 300ns can be obtained, see typical performance
characteristics.
14. Positive excursions of input voltage may exceed the power supply level. As long as other voltages remain within the common mode range, the
comparator will provide a proper output stage. The low voltage state must not be less than -0.3V (or 0.3V below the magnitude of the negative power
supply, if used).

LM2901/ LM2901A/ LM2903/ LM2903A 4 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Electrical Characteristics (Notes 8 & 9) (@VCC = 5.0V, GND = 0V, TA = +25°C, unless otherwise specified.)
LM2903, LM2903A
Parameter Conditions TA Min Typ Max Unit

VIC = VCMR Min, TA = +25°C — 2 7

Non-A Device
VO = 1.4V, Full Range — — 15
VIO Input Offset Voltage mV
VCC = 5V to =30V TA = +25°C — 1 2
A-Suffix Device
(Note 10) Full Range — — 4
IIN+ or IIN− with OUT in Linear Range, TA = +25°C — 25 250
IB Input Bias Current nA
VCM = 0V (Note 11) Full Range — — 500
TA = +25°C — 5 50
IIO Input Offset Current IIN+ - IIN−, VCM = 0V nA
Full Range — — 200
0 to
TA = +25°C — —
Input Common-Mode Voltage VCC -1.5
VCMR VCC = 30V (Note 12) V
Range 0 to
Full Range — —
VCC-2
TA = +25°C — 0.7 1.7
VCC = 30V
RL = ∞ on Full Range — — 3.0
ICC Supply Current mA
Both Channels TA = +25°C — 0.6 1
VCC = 5V
Full Range — — 2.0
VCC = 15V, VOUT = 1V to 11V,
AV Voltage Gain TA = +25°C 50 200 — V/mV
RL ≥ 15kΩ,
VIN = TTL Logic Swing, VREF = 1.4V,
— Large Signal Response Time TA = +25°C — 300 — ns
VRL = 5V, RL = 5.1kΩ
— Response Time VRL = 5V, RL = 5.1kΩ (Note 13) TA = +25°C — 1.3 — µs
IO(SINK) Output Sink Current VIN− = 1V, VIN+ = 0, VO ≤ 1.5V TA = +25°C 6 16 — mA
TA = +25°C — 200 400
VSAT Saturation Voltage VIN− = 1V, VIN+ = 0, ISINK ≤ 4mA mV
Full Range — — 700
VIN− = 0V, VIN+ = 1, VO = 5V TA = +25°C — 0.1 — nA
IO(LEAK) Output Leakage Current
VIN− = 0V, VIN+ = 1, VO = 30V Full Range — — 1 µA
VID Differential Input Voltage All VIN ≥0V (or V- if used) (Note 14) Full Range — — 36 V
Notes: 8. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
9. All limits are guaranteed by testing or statistical analysis. Limits over the full temperature are guaranteed by design, but not tested in production.
10. VO ≅ 1.4V, RS = 0Ω with VCC from 5V to 30V;
11. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the input lines.
12. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (@ +25°C). The upper end of the
common-mode voltage range is VCC -1.5V (@ +25°C), but either or both inputs can go to +36V without damage, independent of the magnitude of VCC.
13. The response time specified is for a 100mV step input with 5mV overdrive. For larger overdrive signals 300ns can be obtained, see typical performance
characteristics.
14. Positive excursions of input voltage may exceed the power supply level. As long as other voltages remain within the common mode range, the
comparator will provide a proper output stage. The low voltage state must not be less than -0.3V (or 0.3V below the magnitude of the negative power
supply, if used).

LM2901/ LM2901A/ LM2903/ LM2903A 5 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Performance Characteristics

Supply Current vs. Supply Voltage Supply Current vs. Supply Voltage

Supply Current vs. Temperature Supply Current vs. Temperature

Output Saturation Voltage vs. Sink Current Output Saturation Voltage vs. Sink Current

LM2901/ LM2901A/ LM2903/ LM2903A 6 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Performance Characteristics (continued)

Response Time for Various Input Overdrive Response Time for Various Input Overdrive

Input Current vs. Supply Voltage Input Current vs. Temperature

LM2901/ LM2901A/ LM2903/ LM2903A 7 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Application Information
General Information
The LM2901/2903 series comparators are high-gain, wide bandwidth devices. Like most comparators, the series can easily oscillate if the output
lead is inadvertently allowed to capacitive couple to the inputs via stray capacitance. This shows up only during the output voltage transition
intervals as the comparators change states. Standard PC board layout is helpful as it reduces stray input-output coupling. Reducing the input
resistors to <10kΩ reduces the feedback signal levels. Finally, adding even a small amount (1.0mV to 10mV) of positive feedback (hysteresis)
causes such a rapid transition that oscillations, due to stray feedback, are not possible. Simply socketing the IC and attaching resistors to the pins
will cause input-output oscillations during the small transition intervals unless hysteresis is used. If the input signal is a pulse waveform, with
relatively fast rise and fall times, hysteresis is not required. All input pins of any unused comparators should be tied to the negative supply.

The bias network of the LM2901/2903 series comparators establishes a quiescent current independent of the magnitude of the power supply
voltage over the range of from 2.0VDC to 30VDC.

The differential input voltage may be larger than VCC without damaging the device. Protection should be provided to prevent the input voltages from
going negative more than -0.3VDC (@ +25°C). An input clamp diode can be used as shown in the applications section.

The output of the LM2901/2903 series comparators is the uncommitted collector of a grounded-emitter NPN output transistor. Many collectors can
be tied together to provide an output ORing function. An output pull-up resistor can be connected to any available power supply voltage within the
permitted supply voltage range and there is no restriction on this voltage due to the magnitude of the voltage applied to the VCC terminal of
LM2901/2903 series comparator package. The output can also be used as a simple SPST switch to ground (when a pull-up resistor is not used).

The amount of current the output device can sink is limited by the drive available (which is independent of VCC) and the β of this device. When the
maximum current limit is reached (approximately 16mA), the output transistor will come out of saturation and the output voltage will rise very
rapidly. The output saturation voltage is limited by the approximately 60Ω RSAT of the output transistor. The low offset voltage of the output
transistor (1.0mV) allows the output to clamp essentially to ground level for small load currents.

LM2901/ LM2901A/ LM2903/ LM2903A 8 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Typical Application Circuit (VCC = 5.0VDC)

Vcc
5V

3KΩ
100KΩ
+VIN + +VIN + 8
Vo
Vo ½ LM2903/A

+VREF - +VREF -

Basic Comparator Driving CMOS

+5VDC V+

10KΩ +VREF - 3KΩ

+
Vo Vo
10KΩ
+
10MΩ
- +VIN

Non-Inverting Comparator with

Hysteresis
Driving TTL

V+
V+

+VIN - 3KΩ

Vo + 5.1KΩ
1MΩ +
V+ + VIN Vo
1MΩ
-
1MΩ -5 VDC
V

Inverting Comparator with Comparator with a

Hysteresis Negative Reference

LM2901/ LM2901A/ LM2903/ LM2903A 9 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Typical Application Circuit (VCC = 5.0VDC) (continued)

V+ V+
R1 D1 15KΩ
200KΩ 2KΩ 1MΩ 1N914

100KΩ
R2 D2
100KΩ 1N914

80pF
V+ V+
- - 6us 60us
0.1uF 0 0
t 0 t1 t2

Vo Vo
+15VDC 1MΩ
+ +
1MΩ

200KΩ CRYSTAL 1MΩ

f = 100KHz
* For large ratios of R1/R2, D1 can
be omitted.

Crystal Controlled Oscillator Pulse Generator

V+
V+

6.2KΩ 39KΩ
3KΩ
- +0.375V
-
Vo 100KΩ 1KΩ
A f
100KΩ
+ STROBE B +
INPUT
* C
100KΩ
V+ 1KΩ

*Or logic gate without pull-up resistor 0

“0”"1”

Output Strobing AND Gate

V+
V+
V+

200KΩ
3KΩ 0
+0.075V “0”"1” 100KΩ
10KΩ 3KΩ
-
100KΩ 1KΩ
-
D1
A f 100KΩ
100KΩ A
B + D2 Vout
B +
C D3
100KΩ C
V+ 1KΩ
D4
0
“0”"1”
D

OR Gate
Large Fan-in AND Gate

LM2901/ LM2901A/ LM2903/ LM2903A 10 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Typical Application Circuit (VCC = 5.0VDC) (continued)

V+(12VDC)

2RS
+VREF HIGH + 10KΩ
2N2222

100KΩ
- +VIN1
RS
LAMP
- 5.1KΩ
+ 12 ESB 100KΩ
VIN + -VIN2

2N2222
+
2RS
+VREF LOW -
Comparing Input Voltage of
Limit Comparator Opposite Polarity

V+ V+
V+

0
+ 3.0KΩ
“0”"1” 100KΩ
100KΩ 5.1KΩ
5.1KΩ
VO -
VIN 5.1KΩ
-
1N914
Vo
+
+ 20MΩ

10KΩ

Zero Crossing Detector

ORing the Outputs
(Single Power Supply)

V+ V+

4.3KΩ

1MΩ 100KΩ
10KΩ
100pF V+
- 75pF
+ 0
- 1:100KHz
0 1MΩ
t0 1N914 Vo
Vo
V+ 100KΩ
+ 1ms PW
0.001uF
0 +
t0 t1 V+ 100KΩ

1MΩ
1N914 100KΩ

One-Shot Multivibrator Squarewave Oscillator

LM2901/ LM2901A/ LM2903/ LM2903A 11 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Ordering Information (Note 15)

LM290X X XXX - 13

Channel Grade Package Packing

1 : Quad Blank : Normal T14 : TSSOP-14 13 : Tape & Reel
3 : Dual A : Low VIO S14 : SO-14
S : SO-8
M8: MSOP-8
TH: TSSOP-8

13” Tape and Reel

Part Number Package Code Packaging
Quantity Part Number Suffix
LM2901T14-13 T14 TSSOP-14 2500/Tape & Reel -13
LM2901AT14-13 T14 TSSOP-14 2500/Tape & Reel -13
LM2901S14-13 S14 SO-14 2500/Tape & Reel -13
LM2901AS14-13 S14 SO-14 2500/Tape & Reel -13
LM2903S-13 S SO-8 2500/Tape & Reel -13
LM2903AS-13 S SO-8 2500/Tape & Reel -13
LM2903AM8-13 M8 MSOP-8 2500/Tape & Reel -13
LM2903M8-13 M8 MSOP-8 2500/Tape & Reel -13
LM2903ATH-13 TH TSSOP-8 2500/Tape & Reel -13
LM2903TH-13 TH TSSOP-8 2500/Tape & Reel -13
Note: 15. For packaging details, go to our website at http://www.diodes.com/products/packages.html.

LM2901/ LM2901A/ LM2903/ LM2903A 12 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Marking Information

(1) TSSOP-14 and SO-14

(2) SO-8

(3) MSOP-8 & TSSOP-8

LM2901/ LM2901A/ LM2903/ LM2903A 13 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Package Outline Dimensions

Please see http://www.diodes.com/package-outlines.html for the latest version.

SO-8

SO-8
Dim Min Max
A − 1.75

0.254
E1 E A1 0.10 0.20
Gauge Plane A2 1.30 1.50
A1 Seating Plane
L A3 0.15 0.25
b 0.3 0.5
Detail ‘A’ D 4.85 4.95
E 5.90 6.10
h 7°~9° E1 3.85 3.95
45° e 1.27 Typ
Detail ‘A’ h − 0.35
A2 A A3
L 0.62 0.82
b θ 0° 8°
e
All Dimensions in mm
D

TSSOP-8

TSSOP-8
Dim Min Max Typ
See Detail C
a 0.09 − −
E A − 1.20 −
E1 A1 0.05 0.15 −
A2 0.825 1.025 0.925
b 0.19 0.30 −
c 0.09 0.20 −
D 2.90 3.10 3.025
e c e − − 0.65
b E − − 6.40
Gauge plane
E1 4.30 4.50 4.425
a
A A2 L 0.45 0.75 0.60
L All Dimensions in mm
D A1
Detail C

MSOP-8
D

MSOP-8
Dim Min Max Typ
4X
10 A − 1.10 −
°
A1 0.05 0.15 0.10
0.25
A2 0.75 0.95 0.86
E A3 0.29 0.49 0.39
x Gauge Plane
Seating Plane
b 0.22 0.38 0.30
c 0.08 0.23 0.15
y
a

L D 2.90 3.10 3.00

4X10° E 4.70 5.10 4.90
Detail C E1 2.90 3.10 3.00
1 E3 2.85 3.05 2.95
b
E3 e − − 0.65
L 0.40 0.80 0.60
A3
a 0° 8° 4°
A2 A x − − 0.750
y − − 0.750
e
E1 All Dimensions in mm
A1 c
See Detail C

LM2901/ LM2901A/ LM2903/ LM2903A 14 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Package Outline Dimensions (continued)

Please see http://www.diodes.com/package-outlines.html for the latest version.

SO-14

SO-14
Dim Min Max
E H Gauge Plane A 1.47 1.73
A1 0.10 0.25
L A2 1.45 Typ
θ
B 0.33 0.51
Detail “A”
D 8.53 8.74
E 3.80 3.99
D A2 e 1.27 Typ
7° A
(4 H 5.80 6.20
x)
L 0.38 1.27
θ 0° 8°
B e All Dimensions in mm
Detail “A”
A1

TSSOP-14

TSSOP-14
0.25

Dim Min Max

Pin# 1 Indent Gauge Plane a1 7° (4X)
B L a2 0° 8°
Seating Plane
F1
A 4.9 5.10
a2

B 4.30 4.50
F
Detail ‘A’
C − 1.2
D 0.8 1.05
F 1.00 Typ
G K
F1 0.45 0.75
A
G 0.65 Typ
a1 D K 0.19 0.30
L 6.40 Typ
C
All Dimensions in mm
Detail ‘A’

LM2901/ LM2901A/ LM2903/ LM2903A 15 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Suggested Pad Layout

Please see http://www.diodes.com/package-outlines.html for the latest version.

SO-8
X

Dimensions Value (in mm)

X 0.60
C1 Y 1.55
C1 5.4
C2 C2 1.27

TSSOP-8

Dimensions Value (in mm)

X X 0.45
C3 C1
Y 1.78
C1 7.72
C2 C2 0.65
G
C3 4.16
G 0.20

MSOP-8

X C

Y
Value
Dimensions
(in mm)
C 0.650
X 0.450
Y1
Y 1.350
Y1 5.300

LM2901/ LM2901A/ LM2903/ LM2903A 16 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

Suggested Pad Layout (continued)

Please see http://www.diodes.com/package-outlines.html for the latest version.

SO-14
X

Dimensions Value (in mm)

X 0.60
Y 1.50
C1
C1 5.4
C2 C2 1.27

TSSOP-14

Dimensions Value (in mm)

X 0.45
Y 1.45
C1 C1 5.9
C2 0.65
C2

LM2901/ LM2901A/ LM2903/ LM2903A 17 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated
 LM2901/ LM2901A/ LM2903/ LM2903A

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.

This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

1. are intended to implant into the body, or

2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.

Copyright © 2018, Diodes Incorporated

www.diodes.com

LM2901/ LM2901A/ LM2903/ LM2903A 18 of 18 September 2018

Document number: DS36779 Rev 4 - 2 www.diodes.com © Diodes Incorporated