Victaulic® QuickVic™ Rigid Coupling

Style 107N 06.23

2 - 12"/50 - 300 mm

1.0  PRODUCT DESCRIPTION

Available Sizes
• 2 – 12"/50 – 300 mm
Pipe Material
• Carbon steel, Stainless steel
Maximum Working Pressure
• Accommodates pressures ranging from full vacuum (29.9 in Hg/760 mm Hg) up to 750 psi/5171 kPa.
• Working pressure dependent on material, wall thickness and size of pipe.
Operating Temperature
• Dependent on gasket selection from section 3.0.
Function
• Joins carbon steel and/or stainless steel pipe.
• Provides a rigid pipe joint designed to restrict axial or angular movement.
Pipe Preparation
• Cut or roll grooved in accordance with Submittal 25.01: Victaulic Standard Groove Specifications.
Codes and Requirements
• Hanger support spacing corresponds to ASME B31.1 Power Piping Code and ASME B31.9 Building Services
Piping Code.

2.0 CERTIFICATION/LISTINGS

NOTES
• See Submittal 10.01: Victaulic Products for Fire Protection Piping Systems - Regulatory Approval Reference Guide for details.
• See Submittal 02.06: Victaulic Potable Water Approvals ANSI/NSF for potable water approvals if applicable.

ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION, MAINTENANCE OR SUPPORT.

System No. Location Spec Section Paragraph

Submitted By Date Approved Date

victaulic.com
06.23 7470 Rev C Updated 04/2017 © 2017 Victaulic Company. All rights reserved.
1
victaulic.com

3.0  SPECIFICATIONS - MATERIAL

Housing:
Ductile iron conforming to ASTM A536, Grade 65-45-12. Ductile iron conforming to ASTM A395, Grade 65-45-
15, is available upon special request.
Housing Coating: (specify choice)
Standard: Orange enamel.
Optional: Hot dipped galvanized.
Optional: Contact Victaulic with your requirements for other coatings.
Gasket: (specify choice1)
Grade "EHP" EPDM

EHP (Red and Green stripes color code). Temperature range –30ºF to +250ºF/–34ºC to +121ºC. May be specified
for hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many
chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +73ºF/+23ºC and hot +180ºF/+82ºC
potable water service and ANSI/NSF 372. NOT COMPATIBLE FOR PETROLEUM SERVICES.
Grade “T” Nitrile

Nitrile (Orange stripe color code). Temperature range -20ºF to +180ºF/-29ºC to +82ºC. May be specified for
petroleum products, air with oil vapors, and vegetable and mineral oils within the specified temperature range.
Not compatible for hot water services over +150ºF/+66ºC or for hot dry air over +140ºF/+60ºC.
Others

For alternate gasket selection, reference Submittal 05.01: Victaulic Seal Selection Guide - Elastometric Seal
Construction.
1 Services listed are General Service Guidelines only. It should be noted that there are services for which these gaskets are not compatible. Reference should
always be made to the latest Victaulic Seal Selection Guide for specific gasket service guidelines and for a listing of services which are not compatible.

Bolts/Nuts: (specify choice2)

Standard: Carbon steel oval neck track bolts meeting the physical and chemical requirements of ASTM
A449 (imperial) and ISO 898-1 Class 9.8 (metric). Carbon steel hex nuts meeting the physical and chemical
requirements of ASTM A563 Grade B (imperial - heavy hex nuts) and ASTM A563M Class 9 (metric - hex nuts).
Track bolts and hex nuts are zinc electroplated per ASTM B633 ZN/FE5, finish Type III (imperial) or Type II
(metric).
Optional: Stainless steel oval neck track bolts meeting the requirements of ASTM F593, Group 2 (316 stainless
steel), condition CW. Stainless steel heavy hex nuts meeting the requirements of ASTM F594, Group 2 (316
stainless steel), condition CW, with galling-resistant coating.2
2 Optional bolts/nuts are available in imperial size only.

06.23 7470 Rev C Updated 04/2017 © 2017 Victaulic Company. All rights reserved.

victaulic.com 2
victaulic.com

4.0 DIMENSIONS
Style 107N

Y Z Y Z

X X

Pre-Assembled
Joint Assembled
(Installation-Ready™ Condition)

Pipe End
Size Separation3 Bolt/Nut4 Dimensions Weight
Actual Pre-Assembled
Outside (Installation-Ready™ Condition) Joint Assembled Approximate
Nominal Diameter Allowable Qty. Size X Y X Y Z (Each)
inches inches inches inches inches inches inches inches inches lb
DN mm mm mm mm mm mm mm mm kg
2 2.375 0.15 1/2 x 3 4.00 6.13 3.63 6.13 2.13 2.7
2
DN50 60.3 3.8 M12 x 76 100 156 92 156 54 1.2
2 1/2 2.875 0.15 1/2 x 3 4.50 6.75 4.00 6.75 2.13 3.0
2
73.0 3.8 M12 x 76 114 171 102 171 54 1.4
3.000 0.15 1/2 x 3 4.63 6.88 4.13 6.88 2.13 3.1
2
DN65 76.1 3.8 M12 x 76 118 175 105 175 54 1.4
3 3.500 0.15 1/2 x 3 1/4 5.25 7.38 4.63 7.50 2.13 3.7
2
DN80 88.9 3.8 M12 x 83 133 187 118 191 54 1.7
4 4.500 0.15 1/2 x 3 1/4 6.63 8.75 5.88 8.75 2.13 5.1
2
DN100 114.3 3.8 M12 x 83 168 222 149 222 54 2.3
4.250 0.15 1/2 x 3 1/4 6.38 8.50 5.75 8.50 2.13 4.7
2
108.0 3.8 M12 x 83 162 216 146 216 54 2.1
5 5.563 0.15 5/8 x 4 7.75 10.25 7.13 10.25 2.25 7.0
2
141.3 3.8 M16 x 101 197 260 181 260 57 3.2
5.250 0.15 5/8 x 4 7.50 10.00 6.75 9.88 2.25 6.1
2
133.0 3.8 M16 x 101 191 254 171 251 57 3.0
5.500 0.15 5/8 x 4 7.75 10.25 7.00 10.13 2.25 6.7
2
DN125 139.7 3.8 M16 x 101 197 260 178 257 57 3.0
6 6.625 0.15 5/8 x 4 8.88 11.38 8.13 11.25 2.25 8.2
2
DN150 168.3 3.8 M16 x 101 226 289 207 286 57 3.7
6.250 0.15 5/8 x 4 8.50 11.00 7.75 10.88 2.25 7.6
2
159.0 3.8 M16 x 101 216 279 197 276 57 3.4
6.500 0.15 5/8 x 4 8.75 11.25 8.00 11.13 2.25 7.9
2
165.1 3.8 M16 x 101 222 286 203 283 57 3.6
8.515 0.22 3/4 x 5 11.25 14.25 10.38 14.13 2.63 15.0
2
216.3 5.6 M20 x 127 286 362 264 359 67 6.8
8 8.625 0.22 3/4 x 5 11.25 14.37 10.50 14.25 2.63 15.1
2
DN200 219.1 5.6 M20 x 127 286 365 267 362 67 6.8
10 10.750 0.20 7/8 x 61/2 13.25 17.00 13.00 17.13 2.75 23.6
2
DN250 273.0 5.1 M22 x 165 337 432 330 435 70 10.7
12 12.750 0.20 7/8 x 61/2 15.63 19.00 15.00 19.00 2.75 27.2
2
DN300 323.9 5.1 M22 x 165 397 483 381 483 70 12.3
3 The allowable pipe end separation dimension shown is for system layout purposes only. Style 107N QuickVic™ rigid couplings are considered rigid connections
and will not accommodate expansion or contraction of the piping system.
4 Number of bolts required equals number of housing segments.

06.23 7470 Rev C Updated 04/2017 © 2017 Victaulic Company. All rights reserved.

victaulic.com 3
victaulic.com

5.0 PERFORMANCE
Style 107N – ANSI Standard
Size Schedule 10 Schedule 40
Maximum Maximum Maximum Maximum
Actual Outside Joint Working Permissible Joint Working Permissible
Nominal Diameter Wall Thickness Pressure5 End Load5 Wall Thickness Pressure5 End Load5
inches inches inches psi lb inches psi lb
DN mm mm kPa N mm kPa N
2 2.375 0.109 750 3323 0.154 750 3323
DN50 60.3 2.8 5171 14781 3.9 5170 14780
2 1/2 2.875 0.120 600 3895 0.203 750 4869
73.0 3.1 4135 17325 5.2 5170 21658
3 3.500 0.120 600 5773 0.216 750 7216
DN80 88.9 3.1 4135 25680 5.5 5170 32098
4 4.500 0.120 600 9543 0.237 750 11928
DN100 114.3 3.1 4135 42449 6.0 5170 53058
5 5.563 0.134 500 12153 0.258 750 18229
141.3 3.4 3447 54059 6.6 5171 81087
6 6.625 0.134 500 17236 0.280 700 24130
DN150 168.3 3.4 3450 76670 7.1 4825 107335
8 8.625 0.148 300 17528 0.322 600 35056
DN200 219.1 3.8 2070 77970 8.2 4135 155936
10 10.750 0.165 300 27200 0.365 500 45400
DN250 273.0 4.2 2065 121040 9.3 3450 202030
12 12.750 0.180 200 25500 0.375 400 51000
DN300 323.9 4.6 1375 113475 9.5 2750 226950
5 Working Pressure and End Load are total, from all internal and external loads, based on ANSI B36.10 sized carbon steel pipe, grooved in accordance with
Victaulic specifications. Contact Victaulic for performance on other pipe.
NOTES
• WARNING: FOR ONE-TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to 11/2 times the figures shown.
• LPCB and VdS approved for DIN wall pipe (6.3mm thickness) for 10" rated to 232 psi/16 bar, (7.8mm thickness) for 12" rated to 232 psi/16 bar.
• FM approved on schedule 10 pipe: 2-4 inch sizes rated to 400 psi/28 bar; 5-6 inch sizes rated to 300 psi/21 bar; and 8 and 10 inch sizes (.188" wall
thickness) rated to 300 psi/21 bar. FM approved on schedule 40 pipe: 2-4 inch sizes rated to 600 psi/41 bar; 5-6 inch sizes rated to 500 psi/34 bar; and 10
and 12 inch sizes rated to 400 psi/28 bar. Includes all metric sizes in range.
• UL listed on schedule 10 pipe: 2, 2 ½, 3 and 4 inch sizes rated to 400 psi; and 6, 8 and 10 inch sizes rated to 300 psi. Schedule 40 pipe: 2, 2 ½ and 3 inch
sizes rated to 600 psi; 4 inch rated to 450 psi; and 6, 8, 10 and 12 inch sizes rated to 400 psi.

06.23 7470 Rev C Updated 04/2017 © 2017 Victaulic Company. All rights reserved.

victaulic.com 4
victaulic.com

5.1 PERFORMANCE
Style 107N – ISO Standard
Size ISO Wall Pipe
Maximum Maximum Maximum Maximum
Actual Outside Joint Working Permissible Joint Working Permissible
Nominal Diameter Wall Thickness Pressure6 End Load6 Wall Thickness Pressure6 End Load6
inches inches inches psi lb inches psi lb
DN mm mm kPa N mm kPa N
2 2.375 0.091 750 3323 0.157 750 3323
50 60.3 2.3 5171 14781 4.0 5171 14780
3.000 0.150 600 4239 0.200 750 5299
DN65 76.1 3.8 4135 18856 5.1 5170 73571
3 3.500 0.114 600 5773 0.197 750 7216
80 88.9 2.9 4135 25680 5.0 5171 32098
4 4.500 0.126 600 9543 0.220 750 11928
100 114.3 3.2 4137 42449 5.6 5171 53058
4.250 0.114 600 8507 0.220 750 10634
108.0 2.3 4135 37841 5.6 5170 47302
5.250 0.142 500 10818 0.248 750 16227
133.0 3.6 3447 48121 6.3 5170 72181
5.500 0.150 500 11873 0.220 750 17810
DN125 139.7 3.8 3447 52814 5.6 5170 79223
6 6.625 0.157 500 17236 0.280 700 24130
150 168.3 4.0 3450 76670 7.1 4826 107335
6.250 0.197 500 15332 0.276 700 21465
159.0 5..0 3447 68200 7.0 4825 95481
6.500 0.134 500 16583 0.276 700 23216
165.1 3.4 3447 73765 7.0 4825 103270
8.515 0.228 300 17075 0.315 600 34150
216.3 5.8 2070 75953 8.0 4135 151907
8 8.625 0.177 300 17528 0.315 600 35056
200 219.1 4.5 2070 77970 8.0 4137 155936
10 10.750 0.228 300 27200 0.248 500 45400
250 273.0 5.8 2065 121040 6.3 3450 202030
12 12.750 0.264 200 25500 0.307 400 51000
300 323.9 6.7 1375 113475 7.8 2750 226950
6 Working Pressure and End Load are total, from all internal and external loads, based on ISO 4200 sized carbon steel pipe, grooved in accordance with
Victaulic specifications. Contact Victaulic for performance on other pipe.
NOTES
• WARNING: FOR ONE-TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to 11/2 times the figures shown.
• LPCB and VdS approved for DIN wall pipe (6.3mm thickness) for 10" rated to 232 psi/16 bar, (7.8mm thickness) for 12" rated to 232 psi/16 bar.
• FM approved on schedule 10 pipe: 2-4 inch sizes rated to 400 psi/28 bar; 5-6 inch sizes rated to 300 psi/21 bar; and 8 and 10 inch sizes (.188" wall
thickness) rated to 300 psi/21 bar. FM approved on schedule 40 pipe: 2-4 inch sizes rated to 600 psi/41 bar; 5-6 inch sizes rated to 500 psi/34 bar; and 10
and 12 inch sizes rated to 400 psi/28 bar. Includes all metric sizes in range.
• UL listed on schedule 10 pipe: 2, 2 ½, 3 and 4 inch sizes rated to 400 psi; and 6, 8 and 10 inch sizes rated to 300 psi. Schedule 40 pipe: 2, 2 ½ and 3 inch
sizes rated to 600 psi; 4 inch rated to 450 psi; and 6, 8, 10 and 12 inch sizes rated to 400 psi.

06.23 7470 Rev C Updated 04/2017 © 2017 Victaulic Company. All rights reserved.

victaulic.com 5
victaulic.com

6.0 NOTIFICATIONS

WARNING
• Victaulic RX roll sets must be used when grooving light-wall/thin-wall stainless steel pipe for use with Victaulic
Couplings.
Failure to use Victaulic RX roll sets when grooving light-wall/thin-wall stainless steel pipe may cause joint failure,
resulting in serious personal injury and/or property damage.

NOTICE
• Victaulic RX grooving rolls must be ordered separately. They are identified by a silver color and the designation
RX on the front of the roll sets.

CAUTION
• When assembling Style 107N Couplings onto end caps, take additional care to ensure the end cap is seated fully
against the center leg of the gasket.
• Use only Victaulic No. 60 End Caps containing the "EZ QV" marking on the inside face.
• Victaulic recommends the use of Victaulic fittings with Style 107N Couplings.
• Victaulic No. 460-SS Stainless Steel End Caps shall not be used with Style 107N Couplings. No. 460-SS End
Caps shall be used only with Style 89 Rigid Couplings for stainless steel pipe.
Failure to follow this instruction could cause improper product installation, resulting in personal injury and/or
property damage.

7.0  REFERENCE MATERIALS

02.06: Victaulic Potable Water Approvals ANSI/NSF
05.01: Victaulic Seal Selection Guide - Elastometric Seal Construction
06.15: Victaulic Pressure Ratings and End Loads for Victaulic Couplings on Steel Pipe
10.01: Victaulic Products for Fire Protection Piping Systems - Regulatory Approval Reference Guide
17.01: Victaulic Pipe Preparation for Use on Stainless Steel Pipe With Victaulic Products
17.09: Victaulic Pressure Ratings and End Loads for Victaulic Ductile Iron Grooved Couplings on Stainless Steel Pipe
25.01: Victaulic Standard Groove Specifications
26.01: Victaulic Design Data
29.01: Victaulic Terms and Conditions of Sale
I-100: Victaulic Field Installation Handbook
I-107: Victaulic Installation Instructions - Style 107N QuickVic™ Installation-Ready™ Rigid Coupling

User Responsibility for Product Selection and Suitability Note

Each user bears final responsibility for making a determination as to the suitability of This product shall be manufactured by Victaulic or to Victaulic specifications. All products
Victaulic products for a particular end-use application, in accordance with industry to be installed in accordance with current Victaulic installation/assembly instructions.
standards and project specifications, as well as Victaulic performance, maintenance, Victaulic reserves the right to change product specifications, designs and standard
safety, and warning instructions. Nothing in this or any other document, nor any verbal equipment without notice and without incurring obligations.
recommendation, advice, or opinion from any Victaulic employee, shall be deemed to Installation
alter, vary, supersede, or waive any provision of Victaulic Company's standard conditions Reference should always be made to the Victaulic installation handbook or installation
of sale, installation guide, or this disclaimer. instructions of the product you are installing. Handbooks are included with each shipment
Intellectual Property Rights of Victaulic products, providing complete installation and assembly data, and are available
No statement contained herein concerning a possible or suggested use of any material, in PDF format on our website at www.victaulic.com.
product, service, or design is intended, or should be constructed, to grant any license Warranty
under any patent or other intellectual property right of Victaulic or any of its subsidiaries Refer to the Warranty section of the current Price List or contact Victaulic for details.
or affiliates covering such use or design, or as a recommendation for the use of such
material, product, service, or design in the infringement of any patent or other intellectual Trademarks
property right. The terms “Patented” or “Patent Pending” refer to design or utility patents Victaulic and all other Victaulic marks are the trademarks or registered trademarks of
or patent applications for articles and/or methods of use in the United States and/or other Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries.
countries.

06.23 7470 Rev C Updated 04/2017 © 2017 Victaulic Company. All rights reserved.

victaulic.com 6