JinkoSolar

Photovoltaic Module

Installation Manual
Contents
1 General Information 1
1.1 Overview 1
1.2 Warnings 1

2. Installation 3
2.1 Installation Safety 3
2.2 Installation Condition 4
2.2.1 Climate Condition 4
2.2.2 Site Selection 4
2.2.3 Tilt Angle Selection 5
2.3 Mechanical Installation Introduction 5
2.3.1 Mounting with Bolts 6
2.3.2 Mounting with Clamps 12

3 Wiring and Connections 22

4 Maintenance and Care 24

4.1 Visual Inspection 24
4.2 Cleaning 24
4.3 Inspection of Connector and Cable 25

5 Electrical Specification 25

6 Disclaimer of Liability 25

Appendix1：Applicable Products 26

Appendix2：Electrical Specifications 31

Edition 04/2020
1. General Information

1.1 Overview

Thanks for choosing Jinko Solar PV modules. In order to ensure the PV modules are installed correctly,
please read the following installation instructions carefully before modules are installed and used.
Please remember that these products generate electricity and certain safety measures need to be taken
to avoid danger.
Make sure the module array is designed in such a way not to exceed the maximum system voltage of
any system component such as connectors or inverters.
The assembly is to be mounted over a fire resistant roof covering rated for the application. Before
mounting the module, please consult your local building department to determine approved roofing
materials.
The modules are qualified for application class A: Hazardous voltage (IEC 61730: higher than 50V DC;
EN 61730: higher than 120V), hazardous power applications (higher than 240W) where general contact
access is anticipated. Modules qualified for safety through EN IEC 61730 -1 and - 2 within this application
class are considered to meet the requirements for Safety Class II.

1.2 Warnings

 PV modules generate DC electrical energy when exposed to sunlight or other light sources. Active
parts of module such as terminals can result in burns, sparks, and lethal shock.
 Artificially concentrated sunlight shall not be directed on
the module or panel.
 Front protective glass is utilized on the module. Broken
solar module glass is an electrical safety hazard (may
cause electric shock or fire). These modules cannot be
repaired and should be replaced immediately.
 To reduce the risk of electrical shocks or burns, modules
may be covered with an opaque material during installation to avoid injury.
 The installation work of the PV array can only be done under the protection of sun-sheltering covers
or sunshades and only qualified person can install or perform maintenance work on this module.
 Follow the battery manufacture’s recommendations if batteries are used with modules.
 Do not use this module to replace or partly replace roofs and walls of living buildings.
 Do not install modules where flammable gas may be present.
 Do not remove any part installed by Jinko Solar or disassemble the module.

-1-
 All instructions should be read and understood before attempting to install, wire, operate and
maintain the module.
 Don’t lift up PV modules using the attached cables or the junction box.
 Do not touch live terminals with bare hands. Use insulated tools for electrical connections.

 All PV systems must be grounded to earth. If there is no special regulation, please follow the National
Electrical Code or other national code.
 Under normal conditions, a photovoltaic module is likely to experience conditions that produce more
current and/or voltage than reported at standard test conditions. Accordingly, the value of Isc and
Voc marked on the module should be multiplied by 1.25 when determining PV system component
voltage ratings, conductor current ratings, fuse sizes, and size of controls connected to the PV output.
 Once the PV module has been shipped to the installation site, all of the parts should be unpacked
properly with care.
 Do not stand or step on the PV module like below pictures show. This is prohibited and there is a
risk of damage to the module and cause injury for you.

 Only PV modules with the same cell size should be connected in series.
 During transporting modules, please attempt to minimize shock or vibration to the module, as this
may damage the module or lead to cell micro cracks.
 During all transportation situations, never drop the module from a vehicle, house or hands. This will
damage module.
 Do not clean the glass with chemicals. Only use tap water. Make sure the module surface
temperature is cool to the touch. Cleaning modules with cool water when module surface temp is
high may result in glass breakage.

-2-
 Do not disconnect any of the modules when under load.
 When looking at PV modules with anti-reflection (AR) coating technology, it will be normal to see
some cells with a slight color difference at different angles. Modules with LRF(light reflective film)
and without LRF should not be built in the same array or roof.
 Connector of junction box can not be contacted with oily substances, for example, lubricant, rust
inhibitor etc.
 The maximum altitude the PV module is designed for ≤ 2000m.
 The maximum irradiance is 1300W/m2 for module with transparent rear.
 Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities.
Contact your local government for information regarding the collection
systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain,
damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally
obligated to take back your old appliance for disposals at least free of
charge.

2. Installation

2.1 Installation Safety

 Always wear protective head gear, insulating gloves and safety shoes (with rubber soles).
 Keep the PV module packed in the carton until installation.
 Do not touch the PV module unnecessarily during installation. The glass surface and the frame may
be hot. There is a risk of burns and electric shock.
 Do not work in rain, snow or windy conditions.
 Due to the risk of electrical shock, do not perform any work if the terminals of the PV module are wet.
 Use insulated tools and do not use wet tools.
 When installing PV modules, do not drop any objects (e.g., PV modules or tools).
 Make sure flammable gasses are not generated or present near the installation site.
 Insert module connectors fully and correctly. An audible "click" sound should be heard. This sounds
confirms the connectors are fully seated. Check all connections.
 The module leads should be securely fastened to the module frame, Wire Management should be

-3-
 done in a way to avoid the connector from scratching or impacting the back sheet of the module.
 Do not touch the junction box and the end of the interconnect cables (connectors) with bare hands
during installation or under sunlight, regardless if the PV module is connected to or disconnected
from the system.
 Do not expose the PV module to excessive loads on the surface of the PV module or twist the frame.
 Do not hit or put excessive load on the glass or back sheet, this may break the cells or cause micro
cracks.
 During the installation or operation, don’t use sharp tools to wipe the back sheet and glass. Scratches
can appear on the module.
 Do not drill holes in the frame. It may cause corrosion of the frame.
 When installing modules on roof mounted structures, please try to follow the “from top to bottom”
and/or “from left to right” principle, and don’t step on the module. This will damage the module and
would be dangerous for personal safety.

2.2 Installation Condition

2.2.1 Climate Condition

Please install the modules in the following conditions:
a) Operating temperature: within –40°C(-40℉) to 85°C (185℉)
b) Humidity: < 85RH%
﹡Note: The mechanical load bearing (include wind and snow loads) of the module is based on the
approved mounting methods. The professional system installer must be responsible for mechanical load
calculation according to the system design.
2.2.2 Site Selection
In most applications, Jinko solar PV modules should be installed in a location where they will receive
maximum sunlight throughout the year. In the Northern Hemisphere, the module should typically face
south, and in the Southern Hemisphere, the modules should typically face north. Modules facing 30
degrees away from true South (or North) will lose approximately10 to 15 percent of their power output. If
the module faces 60 degrees away from true South (or North), the power loss will be 20 to 30 percent.
When choosing a site, avoid trees, buildings or obstructions, which could cast shadows on the solar
photovoltaic modules especially during the winter months when the arc of the sun is lowest over the
horizon. Shading causes loss of output, even though the factory fitted bypass diodes of the PV module
will minimize any such loss.
Do not install the PV module near open flame or flammable materials.
When solar modules are used to charge batteries, the battery must be installed in a manner, which will
protect the performance of the system and the safety of its users. Follow the battery manufacturer’s

-4-
guidelines concerning installation, operation and maintenance recommendations. In general, the battery
(or battery bank) should be away from the main flow of people and animal traffic. Select a battery site
that is protected from sunlight, rain, snow, debris, and is well ventilated. Most batteries generate hydrogen
gas when charging, which can be explosive. Do not light matches or create sparks near the battery bank.
When a battery is installed outdoors, it should be placed in an insulated and ventilated battery case
specifically designed for the purpose.
Do not install the PV module in a location where it would be immersed in water or continually exposed to
water from a sprinkler or fountain etc.
2.2.3 Tilt Angle Selection
The tilt angle of the PV module is measured between the surface of the PV module and a horizontal
ground surface (Figure 1). The PV module generates maximum output power when it faces the sun
directly.
For standalone systems with batteries where the PV modules are attached to a permanent structure, the
tilt angle of the PV modules should be selected to optimize
the performance based on seasonal load and sunlight. In
general, if the PV output is adequate when irradiance is
low (e.g., winter), then the angle chosen should be
adequate during the rest of the year. For grid-connected
installations where the PV modules are attached to a
permanent structure, PV modules should be tilted so that
the energy production from the PV modules will be
maximized on an annual basis.
Figure1: PV module tilt angle

2.3 Mechanical Installation Introduction

Solar PV modules usually can be mounted by using the following methods: bolts and clamps.
﹡Note:
1) All installation methods herein are only for reference, and Jinko solar will not provide related mounting
components, the system installer or trained professional personnel must be responsible for the PV
system’s design, installation, and mechanical load calculation and security of the system.
2) Before installation, the following items should be addressed:
a) Visually check the module for any damage. Clean the module if any dirt or residue remains from
shipping .
b) Check if module serial number stickers match.
3) Jinko modules are designed to meet a maximum positive (or downward) pressure of 3600Pa (Only

-5-
 refer to the mentioned module type in this manual) and negative (or upward) pressure of 1600Pa.
This design load was then tested with a safety factor of 1.5 times. So Jinko modules are tested under
a maximum downward pressure of 5400Pa and upward pressure of 2400Pa. When mounting
modules in snow-prone or high-wind environments, special care should be taken to mount the
modules in a manner that provides sufficient design strength while meeting local code requirements.
2.3.1 Mounting with Bolts
For mounting with bolts, the following modules in tables 1 are applicable.
The frame of each module has 8 mounting holes (Length* Width: 14mm*9mm) used to secure the
modules to support structure. Always use all the eight mounting holes to secure the modules. The module
frame must be attached to a mounting rail using M8 corrosion-proof bolts together with spring washers
and flat washers in eight symmetrical locations on the PV module. The applied torque value should be
big enough to fix the modules steadily. The reference value for M8 bolt is 16~20N*m. As to special support
system or special installation requirement, please reconfirm with the support’s supplier for the torque
value. Please find detailed mounting information in the below illustration as Figure 2&3&4.

2.3.1.1 Mounting with Bolts（eight mounting holes）

Figure 2: PV module installed with bolt fitting method（eight mounting holes）

-6-
 Max. Design Pressure: 3600Pa (positive )
Max. Design Pressure:
&1600Pa (negative) mechanical load
3600Pa (positive ) &1600Pa
Note：The installation method is based
Module type (negative) mechanical load
on the internal results in Jinko.
Module dimensions(mm)
A*B
Height of the frame（mm） 35 30
Group 1 1650*992 & 1665*1002
Group 2 1665*992 & 1684*1002
Group 3 1650*992 & 1665*1002
Group 4 1665*992 & 1684*1002
Group 5 1650*992 & 1665*1002
Group 6 1665*992 & 1684*1002
60P Group 7 1650*992 & 1665*1002
Group 8 1665*992 & 1684*1002
1665*992 & 1684*1002
Group 9
1672*992 & 1704*1008
Group 20 1704*1008
Group 22 1684*1002
Group 30 1704*1008
Group 46 1684*1002
Height of the frame（mm） 40 30
Group 10 1956*992 & 1979*1002
Group 11 1987*992 & 2008*1002
Group 12 1956*992 & 1979*1002
Group 13 1987*992 & 2008*1002
Group 14 1956*992 & 1979*1002
Group 15 1987*992 & 2008*1002
72P
Group 16 1956*992 & 1979*1002
Group 17 1987*992 & 2008*1002
Group 18 1987*992 & 2008*1002 & 2031*1008
Group 19 2031*1008
Group 21 2008*1002
Group 29 2031*1008
Group 45 2008*1002
Height of the frame（mm） 35 30
Group 24 1796*995 & 1796*998
Group 26 1822*1008
66P
Group 28 1822*1008
Group 32 1840*998 & 1841*1002
Group 34 1868*1008 & 1865*1005

-7-
 Group 36 1868*1008 & 1865*1005
Group 38 1840*998 & 1841*1002
1842*1021 & 1842*1024
Group 40
1855*1029 & 1855*1032
Group 42 1868*1034 & 1878*1032
Group 44 1868*1034 & 1878*1032
1842*1021 & 1842*1024
Group 48
1855*1029 & 1855*1032
Height of the frame（mm） 40 35
Group 23 2113*995 & 2113*998
Group 25 2130*1002 & 2139*1008
Group 27 2130*1002 & 2139*1008
Group 31 2163*995 & 2167*997 & 2167*998 & 2166*1002
Group 33 2194*1008 & 2190*1005
Group 35 2194*1008 & 2190*1005
78P
Group 37 2163*995 & 2167*997 & 2167*998 & 2166*1002
2168*1021 & 2168*1024
Group 39
2182*1029 & 2182*1032
Group 41 2194*1034 & 2205*1032
Group 43 2194*1034 & 2205*1032
2168*1021 & 2168*1024
Group 47
2182*1029 & 2182*1032

Table 1: Mechanical dimensions for bolt fitting method（eight mounting holes）

Notes：Group 1~48 refer to appendix 1 for details.
According to IEC 61215 for a maximum positive design loading of below 3600Pa, and negative design
loading 1600Pa, with 1.5 times safety factor.
2.3.1.2 Mounting with Bolts（four mounting holes）

Figure 3: PV module installed with bolt fitting method（four mounting holes）

-8-
 Max. Design Pressure: 3600Pa (positive )
&1600Pa (negative) mechanical load
Module type
Module dimensions(mm)
A*B
Height of the frame（mm） 30
Group 1 1650*992 & 1665*1002
Group 2 1665*992 & 1684*1002
Group 3 1650*992 & 1665*1002
Group 4 1665*992 & 1684*1002
Group 5 1650*992 & 1665*1002
Group 6 1665*992 & 1684*1002
60P Group 7 1650*992 & 1665*1002
Group 8 1665*992 & 1684*1002
1665*992 & 1684*1002
Group 9
1672*992 & 1704*1008
Group 20 1704*1008
Group 22 1684*1002
Group 30 1704*1008
Group 46 1684*1002
Height of the frame（mm） 30
Group 10 1956*992 & 1979*1002
Group 11 1987*992 & 2008*1002
Group 12 1956*992 & 1979*1002
Group 13 1987*992 & 2008*1002
Group 14 1956*992 & 1979*1002
Group 15 1987*992 & 2008*1002
72P
Group 16 1956*992 & 1979*1002
Group 17 1987*992 & 2008*1002
Group 18 1987*992 & 2008*1002 & 2031*1008
Group 19 2031*1008
Group 21 2008*1002
Group 29 2031*1008
Group 45 2008*1002
Height of the frame（mm） 30
Group 24 1796*995 & 1796*998
Group 26 1822*1008
Group 28 1822*1008
66P
Group 32 1840*998 & 1841*1002
Group 34 1868*1008 & 1865*1005
Group 36 1868*1008 & 1865*1005
Group 38 1840*998 & 1841*1002

-9-
 1842*1021 & 1842*1024
Group 40
1855*1029 & 1855*1032
Group 42 1868*1034 & 1878*1032
Group 44 1868*1034 & 1878*1032
1842*1021 & 1842*1024
Group 48
1855*1029 & 1855*1032
Height of the frame（mm） 35
Group 23 2113*995 & 2113*998
Group 25 2130*1002 & 2139*1008
Group 27 2130*1002 & 2139*1008
2163*995 & 2167*997
Group 31
2167*998 & 2166*1002
Group 33 2194*1008 & 2190*1005
Group 35 2194*1008 & 2190*1005
78P
2163*995 & 2167*997
Group 37
2167*998 & 2166*1002
2168*1021 & 2168*1024
Group 39
2182*1029 & 2182*1032
Group 41 2194*1034 & 2205*1032
Group 43 2194*1034 & 2205*1032
2168*1021 & 2168*1024
Group 47
2182*1029 & 2182*1032

Table 2: Mechanical dimensions for bolt fitting method（four mounting holes）

Note：The installation method of bolt fitting（four mounting holes）is based on the internal results in Jinko.
According to IEC 61215 for a maximum positive design loading of below 3600Pa, and negative design
loading 1600Pa, with 1.5 times safety factor.
2.3.1.3 Mounting with Bolts（Nextracker four mounting holes）

Figure 4: PV module installed with bolt fitting method (NEX)

-10-
 Max. Design Pressure: 1067Pa (positive ) &1067Pa
(negative) mechanical load
Module type
Module dimensions(mm)
A*B
Height of the frame（mm） 35 30
Group 1 1650*992 & 1665*1002
Group 2 1665*992 & 1684*1002
Group 3 1650*992 & 1665*1002
Group 4 1665*992 & 1684*1002
Group 5 1650*992 & 1665*1002
Group 6 1665*992 & 1684*1002
60P Group 7 1650*992 & 1665*1002
Group 8 1665*992 & 1684*1002
1665*992 & 1684*1002
Group 9
1672*992 & 1704*1008
Group 20 1704*1008
Group 22 1684*1002
Group 30 1704*1008
Group 46 1684*1002
Height of the frame（mm） 40 30
Group 10 1956*992 & 1979*1002
Group 11 1987*992 & 2008*1002
Group 12 1956*992 & 1979*1002
Group 13 1987*992 & 2008*1002
Group 14 1956*992 & 1979*1002
Group 15 1987*992 & 2008*1002
72P
Group 16 1956*992 & 1979*1002
Group 17 1987*992 & 2008*1002
Group 18 1987*992 & 2008*1002 2031*1008
Group 19 2031*1008
Group 21 2008*1002
Group 29 2031*1008
Group 45 2008*1002
Height of the frame（mm） 40 35
Group 23 2113*995 & 2113*998
Group 25 2130*1002 & 2139*1008
Group 27 2130*1002 & 2139*1008
78P
Group 31 2163*995 & 2167*997 & 2167*998 & 2166*1002
Group 33 2194*1008 & 2190*1005
Group 35 2194*1008 & 2190*1005
Group 37 2163*995 & 2167*997 & 2167*998 & 2166*1002

-11-
 Group 39 2168*1021 & 2168*1024 & 2182*1029 & 2182*1032
Group 41 2194*1034 & 2205*1032
Group 43 2194*1034 & 2205*1032

Group 47 2168*1021 & 2168*1024 & 2182*1029 & 2182*1032

Table 3: Mechanical dimensions for bolt fitting method (NEX)

Note：The installation method of bolt fitting (NEX) is based on the experimental results in Jinko.
According to IEC 61215 for a maximum positive design loading of below 1067Pa, and negative design
loading 1067Pa, with 1.5 times safety factor.

2.3.2 Mounting with clamps

The module clamps should not come into contact with the front glass and must not deform the frame. Be
sure to avoid shadowing effects from the module clamps. The module frame is not to be modified under
any circumstances. When choosing this type of clamp-mounting method, please be sure to use at least
four clamps on each module, two clamps should be attached on each long sides of the module.
Depending on the local wind and snow loads, if excessive pressure load is expected, additional clamps
or support would be required to ensure the module can bear the load. The applied torque value should
be big enough to fix the modules steadily (Please consult with the clamp or support’s supplier for the
specific torque value). Please find detailed mounting information in the below illustration, the mounting
place distance is suggested bigger than J and less than K. The installation diagram of clamp is shown in
figure 5.
Note: The Movement of the mounting rail and the clamps center line are recommended to be within the
black arrow area.
The min length of clamps is 50mm.

-12-
 Middle modules Fringe modules

Figure 5: PV module installed at the side with Clamp fitting method

When installing modules using clamps on the long side of the frame, the applicable product types and
installation locations are shown in figure 6 and table 4.
When installing modules using clamps on the short side of the frame, the applicable product types and
installation locations are shown in figure 7 and table 5.
When installing modules using clamps on the long side & short side of the frame, the applicable product
types and installation locations are shown in figure 8 and table 6.
When installing modules using clamps on the long side of the frame, the applicable product types and
installation locations (The without C transparent backsheet series module) are shown in figure 9 and
table 7.

-13-
2.3.2.1 Clamp Mounting on Long Sides of the Frames

Figure 6: Installation of clamps on long side of frames

3600Pa (positive )
&1600Pa (negative)
3600Pa (positive )
mechanical load
Max. Design Pressure: &1600Pa (negative)
Note：The installation
Module type mechanical load
method is based on the
internal results in Jinko.
Module dimensions(mm)
J K J K
A*B
Height of the frame（mm） 35 30
Group 1 1650*992 & 1665*1002 280 420
Group 2 1665*992 & 1684*1002 280 420
Group 3 1650*992 & 1665*1002 280 420
Group 4 1665*992 & 1684*1002 280 420
Group 5 1650*992 & 1665*1002 280 420
Group 6 1665*992 & 1684*1002 280 420
L/4±50mm( L is the
60P Group 7 1650*992 & 1665*1002 280 420
length of the long side
Group 8 1665*992 & 1684*1002 280 420
of the module)
1665*992 & 1684*1002
Group 9 280 420
1672*992 & 1704*1008
Group 20 1704*1008 280 420
Group 22 1684*1002 280 420
Group 30 1704*1008 280 420
Group 46 1684*1002 280 420

-14-
 Height of the frame（mm） 40 30
Group 10 1956*992 & 1979*1002 280 420
Group 11 1987*992 & 2008*1002 280 420
Group 12 1956*992 & 1979*1002 280 420
Group 13 1987*992 & 2008*1002 280 420
Group 14 1956*992 & 1979*1002 280 420
Group 15 1987*992 & 2008*1002 280 420 L/4±50mm( L is the
72P
Group 16 1956*992 & 1979*1002 280 420 length of the long side
Group 17 1987*992 & 2008*1002 280 420 of the module)
Group 18 1987*992 & 2008*1002 & 2031*1008 280 420
Group 19 2031*1008 280 420
Group 21 2008*1002 280 420
Group 29 2031*1008 280 420
Group 45 2008*1002 280 420
Height of the frame（mm） 35 30
Group 24 1796*995 & 1796*998 280 420
Group 26 1822*1008 280 420
Group 28 1822*1008 280 420
Group 32 1840*998 & 1841*1002 280 420
Group 34 1868*1008 & 1865*1005 280 420
Group 36 1868*1008 & 1865*1005 280 420 L/4±50mm( L is the
66P
Group 38 1840*998 & 1841*1002 280 420 length of the long side
1842*1021 & 1842*1024 & of the module)
Group 40 280 420
1855*1029 & 1855*1032
Group 42 1868*1034 & 1878*1032 280 420
Group 44 1868*1034 & 1878*1032 280 420
1842*1021 & 1842*1024 &
Group 48 280 420
1855*1029 & 1855*1032
Height of the frame（mm） 40 35
Group 23 2113*995 & 2113*998 380 520
Group 25 2130*1002 & 2139*1008 380 520
Group 27 2130*1002 & 2139*1008 380 520
2163*995 & 2167*997
Group 31 380 520
2167*998 & 2166*1002
L/4±50mm( L is the
78P Group 33 2194*1008 & 2190*1005 380 520
length of the long side
Group 35 2194*1008 & 2190*1005 380 520
of the module)
2163*995 & 2167*997
Group 37 380 520
2167*998 & 2166*1002
2168*1021 & 2168*1024 &
Group 39 385 530
2182*1029 & 2182*1032
Group 41 2194*1034 & 2205*1032 390 540

-15-
 Group 43 2194*1034 & 2205*1032 390 540
2168*1021 & 2168*1024 &
Group 47 385 530
2182*1029 & 2182*1032
Table 4: Mechanical dimensions of modules installed with clamps on long side of frame
According to IEC 61215 for a maximum positive design loading of below 3600Pa, and negative design
loading 1600Pa, with 1.5 times safety factor.

2.3.2.2 Clamp Mounting on Short Sides of the Frames

Figure 7: Installation of clamps on short side of frames

1067Pa (positive ) 1067Pa (positive )

Max. Design Pressure: &1067Pa (negative) &1067Pa (negative)
Module type mechanical load mechanical load
Module dimensions(mm)
J K J K
A*B
Height of the frame（mm） 35 30
Group 1 1650*992 & 1665*1002 50 240 100 240
Group 2 1665*992 & 1684*1002 50 240 100 240
Group 3 1650*992 & 1665*1002 50 240 100 240
Group 4 1665*992 & 1684*1002 50 240 100 240
Group 5 1650*992 & 1665*1002 50 240 100 240
Group 6 1665*992 & 1684*1002 50 240 100 240
60P Group 7 1650*992 & 1665*1002 50 240 100 240
Group 8 1665*992 & 1684*1002 50 240 100 240
1665*992 & 1684*1002
Group 9 50 240 100 240
1672*992 & 1704*1008
Group 20 1704*1008 50 240 100 240
Group 22 1684*1002 50 240 100 240
Group 30 1704*1008 50 240 100 240
Group 46 1684*1002 50 240 100 240
72P Height of the frame（mm） 40 30

-16-
 Group 10 1956*992 & 1979*1002 50 240 100 240
Group 11 1987*992 & 2008*1002 50 240 100 240
Group 12 1956*992 & 1979*1002 50 240 100 240
Group 13 1987*992 & 2008*1002 50 240 100 240
Group 14 1956*992 & 1979*1002 50 240 100 240
Group 15 1987*992 & 2008*1002 50 240 100 240
Group 16 1956*992 & 1979*1002 50 240 100 240
Group 17 1987*992 & 2008*1002 50 240 100 240
1987*992 & 2008*1002 &
Group 18 50 240 100 240
2031*1008
Group 19 2031*1008 50 240 100 240
Group 21 2008*1002 50 240 100 240
Group 29 2031*1008 50 240 100 240
Group 45 2008*1002 50 240 100 240
Height of the frame（mm） 35 30
Group 24 1796*995 & 1796*998 130 240 130 240
Group 26 1822*1008 130 240 130 240
Group 28 1822*1008 130 240 130 240
Group 32 1840*998 & 1841*1002 130 240 130 240
Group 34 1868*1008 & 1865*1005 130 240 130 240
Group 36 1868*1008 & 1865*1005 130 240 130 240
66P
Group 38 1840*998 & 1841*1002 130 240 130 240
1842*1021 & 1842*1024 &
Group 40 130 240 130 240
1855*1029 & 1855*1032
Group 42 1868*1034 & 1878*1032 130 240 130 240
Group 44 1868*1034 & 1878*1032 130 240 130 240
1842*1021 & 1842*1024 &
Group 48 130 240 130 240
1855*1029 & 1855*1032
Table 5: Mechanical dimensions of modules installed with clamps on short side of frame
Note：The installation method of clamps on short sides is based on the internal results in Jinko.
According to IEC 61215 for a maximum positive design loading of below 1067Pa, and negative design
loading 1067Pa, with 1.5 times safety factor.

-17-
2.3.2.3 Clamp Mounting on Long & Short Sides

Figure 8: Installation methods of clamps on long and short sides

Max. Design 1600Pa (positive ) &1600Pa 1600Pa (positive ) &1600Pa (negative)

Pressure: (negative) mechanical load mechanical load
Module type
Module
dimensions(mm) J K M N J K M N
A*B
Height of the frame（mm） 35 30
1650*992 &
Group 1 50 240 280 420 100 240
1665*1002
1665*992 &
Group 2 50 240 280 420 100 240
1684*1002
1650*992 &
Group 3 50 240 280 420 100 240
1665*1002
1665*992 &
Group 4 50 240 280 420 100 240
1684*1002 L/4±50mm( L is
60P 1650*992 & the length of the
Group 5 50 240 280 420 100 240
1665*1002 long side of the
1665*992 & module)
Group 6 50 240 280 420 100 240
1684*1002
1650*992 &
Group 7 50 240 280 420 100 240
1665*1002
1665*992 &
Group 8 50 240 280 420 100 240
1684*1002
1665*992 &
Group 9 50 240 280 420 100 240
1684*1002

-18-
 1672*992 &
1704*1008
Group 20 1704*1008 50 240 280 420 100 240
Group 22 1684*1002 50 240 280 420 100 240
Group 30 1704*1008 50 240 280 420 100 240
Group 46 1684*1002 50 240 280 420 100 240
Height of the frame（mm） 40 30
1956*992 &
Group 10 50 240 280 480 100 240
1979*1002
1987*992 &
Group 11 50 240 280 480 100 240
2008*1002
1956*992 &
Group 12 50 240 280 480 100 240
1979*1002
1987*992 &
Group 13 50 240 280 480 100 240
2008*1002
1956*992 &
Group 14 50 240 280 480 100 240
1979*1002
L/4±50mm( L is
1987*992 &
72P Group 15 50 240 280 480 100 240 the length of the
2008*1002
long side of the
1956*992 &
Group 16 50 240 280 480 100 240 module)
1979*1002
1987*992 &
Group 17 50 240 280 480 100 240
2008*1002
1987*992 &
Group 18 2008*1002 & 50 240 280 480 100 240
2031*1008
Group 19 2031*1008 50 240 280 480 100 240
Group 21 2008*1002 50 240 280 480 100 240
Group 29 2031*1008 50 240 280 480 100 240
Group 45 2008*1002 50 240 280 480 100 240
Height of the frame（mm） 35 30
1796*995 &
Group 24 130 240 280 420 130 240
1796*998
Group 26 1822*1008 130 240 280 420 130 240
Group 28 1822*1008 130 240 280 420 130 240 L/4±50mm( L is
66P 1840*998 & the length of the
Group 32 130 240 280 420 130 240
1841*1002 long side of the
1868*1008 & module)
Group 34 130 240 280 420 130 240
1865*1005
1868*1008 &
Group 36 130 240 280 420 130 240
1865*1005

-19-
 1840*998 &
Group 38 130 240 280 420 130 240
1841*1002
1842*1021 &
1842*1024 &
Group 40 130 240 280 420 130 240
1855*1029 &
1855*1032
1868*1034 &
Group 42 130 240 280 420 130 240
1878*1032
1868*1034 &
Group 44 130 240 280 420 130 240
1878*1032
1842*1021 &
1842*1024 &
Group 48 130 240 280 420 130 240
1855*1029 &
1855*1032
Height of the frame（mm） 40 35
2113*995 &
Group 23 130 240 380 520 130 240
2113*998
2130*1002 &
Group 25 130 240 380 520 130 240
2139*1008
2130*1002 &
Group 27 130 240 380 520 130 240
2139*1008
2163*995 &
2167*997
Group 31 130 240 380 520 130 240
2167*998 &
2166*1002
2194*1008 &
Group 33 130 240 380 520 130 240
2190*1005 L/4±50mm( L is
78P 2194*1008 & the length of the
Group 35 130 240 380 520 130 240
2190*1005 long side of the
2163*995 & module)
2167*997
Group 37 130 240 380 520 130 240
2167*998 &
2166*1002
2168*1021 &
2168*1024 &
Group 39 130 240 385 530 130 240
2182*1029 &
2182*1032
2194*1034 &
Group 41 130 240 390 540 130 240
2205*1032
2194*1034 &
Group 43 130 240 390 540 130 240
2205*1032

-20-
 2168*1021 &
2168*1024 &
Group 47 130 240 385 530 130 240
2182*1029 &
2182*1032
Table 6: Mechanical dimensions of modules installed with clamps on short side of frame
Note：The installation method of clamps on long and short sides is based on the internal results in Jinko.
According to IEC 61215 for a maximum positive design loading of below 1600Pa, and negative design
loading 1600Pa, with 1.5 times safety factor.

2.3.2.4 Clamp Mounting on Long Sides of the Frames (The without C transparent
backsheet series module)

Figure 9: Installation methods of clamps on long sides

3600Pa (positive )
Max. Design Pressure: &1600Pa (negative)
Module type mechanical load
Module dimensions(mm)
J K
A*B
Height of the frame（mm） 40
72P Group 19 2031*1008 300 480
Group 29 2031*1008 300 480
Height of the frame（mm） 40
2130*1002 &
Group 25 300 480
2139*1008 & 2110*998
78P 2130*1002 &
Group 27 300 480
2139*1008 & 2110*998
Group 33 2194*1008 & 2190*1005 300 480
Group 35 2194*1008 & 2190*1005 300 480

-21-
 Group 41 2194*1034 & 2205*1032 390 540
Group 43 2194*1034 & 2205*1032 390 540
Table 7: Mechanical dimensions when modules installed at long side with Clamp fitting method
According to IEC 61215 for a maximum positive design loading of below 3600Pa, and negative design
loading 1600Pa, with 1.5 times safety factor.

3. Wiring and Connection

a) Before this procedure, please read the operation instructions of the PV system carefully. Make wiring
by Multi-connecting cables between the PV modules in series or parallel connection, which is
determined by user’s configuration requirement for system power, current and voltage.
b) PV modules connected in series should have similar current, and modules must not be connected
together to create a voltage higher than the permitted system voltage. The maximum number of
modules in series depends on system design, the type of inverter used and environmental conditions.
c) The maximum fuse rating value in an array string can be found on the product label or in the product
datasheet. The fuse rating value is also corresponding to the maximum reverse current that a module
can withstand, i.e. when one string is in shade then the other parallel strings of modules will be loaded
by the shaded string and the current will pass through to create a current circuit. Based on the
maximum series fuse rating of module and local electrical codes and standards, make sure the
modules strings in parallel are protected with the appropriate in-line string fusing.
d) Open the combiner box of the control system and connect the conductor from the PV arrays to the
combiner box in accordance with the design and local codes and standards. The cross-sectional area
and cable connector capacity must satisfy the maximum short-circuit of the PV system (for a single
component, we recommended that the cross-sectional area of cables be 4mm2 and the rated current
of connectors be more than 10A), otherwise cables and connectors will become overheating for large
current. Please pay attention to the temperature limit of cables is 85℃.
e) All module frames and mounting racks must be properly grounded in accordance with local and
national electrical codes. Attach the equipment grounding conductor to the module frame using the
hole and hardware provided. Note that a stainless steel star washer is used between the ground wire
and module frame (see Figure 10 below).This washer is used to avoid corrosion due to dissimilar
metals. Tighten the screw securely.

-22-
 Figure 10：Ground installation of PV modules
f) Follow the requirements of applicable local and national electrical codes.
g) These modules contain factory installed by pass diode .If these modules are incorrectly connected to
each other, the bypass diodes, cable or junction box may be damaged.
h) The cable of the junction box is defined as L, as showed below in Figure 11. For Jinko standard full
module L is 900/1200mm, the half–cut module L is 145/290mm, and the SWAN bifacial module L is
150/250mm. For customized module, L can be based on your condition. Please take the cable length
into consideration before designing the wiring layout.

Figure 11 (1): The full module junction box

Figure 11 (2): The half–cut module/SWAN bifacial module junction box

i) It is recommend to use negatively grounded inverters to avoid the PID effect for non-PID free
modules.
j) If modules are connected in series, the total voltage is equal to the sum of individual voltages. The
recommended as below,

-23-
 System voltage≥N*Voc[1+TCVoc* (Tmin-25)]
Where
N module numbers in series
Voc Open circuit voltage (refer to product label or data sheet)
TCVoc Temperature coefficient of open circuit voltage (refer to product label or data sheet)
Tmin Minimum ambient temperature

4. Maintenance and Care

It is required to perform regular inspection and maintenance of the modules, especially during the
warranty period. To ensure optimum module performance, Jinko recommends the following maintenance
measures:

4.1 Visual Inspection

Inspect the modules visually to find if there are any visual defects, If there are, the following items should
be evaluated:
a) If modules are observed having slight cell color differences at different angles, this is a normal
phenomenon of modules with anti-reflection coating technology.
b) Whether the glass is broken.
c) No sharp objects are in contact with the PV module surfaces.
d) PV modules are not shaded by unwanted obstacles and; or foreign material.
e) Corrosion along the cells’ bus-bar. The corrosion is caused by moisture intrusion thought the module
back sheet. Check the back sheet for damage.
f) Check whether the back sheet is burn out.
g) Check if screws and mounting brackets are tight, adjust and tighten as necessary.

4.2 Cleaning

a) A build up of dust or dirt on the module(s) front face will result in a decreased energy output. Clean
the panel(s) preferably once per annum if possible (depend on site conditions) using a soft cloth dry
or damp, as necessary. Water with high mineral content may leave deposits on the glass surface
and is not recommended.
b) Never use abrasive material under any circumstances.
c) In order to reduce the potential for electrical and thermal shock, Jinko recommends cleaning PV
modules during early morning or late afternoon hours when solar radiation is low and the modules
are cooler, especially in regions with hotter temperatures.
d) Never attempt to clean a PV module with broken glass or other signs of exposed wiring, as this

-24-
 presents a shock hazard.
e) Never use chemicals when cleaning modules as this may affect the module warranty and energy
output.

4.3 Inspection of Connector and Cable

It’s recommended to implement the following preventive maintenance every 6 months:

a) Check the sealing gels of the junction box for any damage.
b) Examine the PV module(s) for signs of deterioration. Check all wiring for possible rodent damage,
weathering and that all connections are tight and corrosion free. Check electrical leakage to ground.

5. Electrical Specification

The module electrical rating are measured under Standard Test Conditions, which are 1000W/m2,
irradiance with AM 1.5 spectrum and 25 deg (77°F) ambient temperature. The module might produce
more or less voltage or current than rated value in uncertainty condition.

6. Disclaimer of Liability

Because the use of the manual and the conditions or methods of installation, operation, use and
maintenance of photovoltaic (PV) product are beyond Jinko’s control, Jinko does not accept responsibility
and expressly disclaims liability for loss ,damage, or expense arising out of or in any way connected with
such installation, operation, use or maintenance.
No responsibility is assumed by Jinko for any infringement of patents or other rights of third parties, which
may result from use of the PV product. NO license is granted by implication or otherwise under any patent
or patent rights.
The information in this manual is based on Jinko’s knowledge and experience and is believed to be
reliable, but such information including product specification (without limitations) and suggestions do not
constitute a warranty, expresses or implied. Jinko reserve the right to change the manual, the PV produce,
the specifications, or product information sheets without prior notice.

-25-
Appendix 1： Applicable Products

This document is applicable to the series of solar modules as listed below:

With 6” poly and mono c-Si:
Group 1
① ② ③
JKMxxxPP -60 JKMxxxPP-60(Plus) JKMS xxxPP-60 JKMSxxxPP-60-J
④
JKMxxxPP-60-V JKMxxxPP-60(Plus) -V JKMSxxxPP-60-V JKMSxxxPP-60-V-J

(xxx=260~290,in increment of 5)
Group 2
⑤
JKMxxxPP-60H JKMxxxPP-60H-V JKMxxxPP-60HB
(xxx =260~315,in increment of 5)
Group 3
JKMSxxxPP-60-V-MX3 JKMSxxxPP-60B-V-MX3 JKMSxxxPP-60-MX3 JKMSxxxPP-60B -MX3
(xxx =260~290,in increment of 5)
JKMSxxxPP-60L-V-MX3 JKMSxxxPP-60BL-V-MX3 JKMSxxxPP-60L -MX3 JKMSxxxPP-60BL -MX3
(xxx =260~290,in increment of 5)
Group 4
JKMSxxxPP-60H-V-MX3 JKMSxxxPP-60HB-V-MX3 JKMSxxxPP-60H-MX3 JKMSxxxPP-60HB -MX3
(xxx =260~315,in increment of 5)
JKMSxxxPP-60HL-V-MX3 JKMSxxxPP-60HBL-V-MX3 JKMSxxxPP-60HL -MX3 JKMSxxxPP-60HBL -MX3
(xxx =260~315,in increment of 5)
Group 5
JKMxxxM-60 JKMxxxM-60(Plus) JKMSxxxM-60 JKMSxxxM-60-J
JKMxxxM-60-V JKMxxxM-60(Plus)- V JKMSxxxM-60-V JKMSxxxM-60-V-J
JKMxxxM-60B
(xxx =270~340,in increment of 5)
⑥
JKMxxxM-60L JKMxxxM-60L-V JKMxxxM-60BL
(xxx =270~340,in increment of 5)
Group 6
JKMxxxM-60H JKMxxxM-60H-V JKMxxxM-60HB
(xxx =270~350,in increment of 5)
JKMxxxM-60HL JKMxxxM-60HL-V JKMxxxM-60HBL
(xxx =270~350,in increment of 5)
Group 7
JKMSxxxM-60-V-MX3 JKMSxxxM-60B-V-MX3 JKMSxxxM-60-MX3 JKMSxxxM-60B -MX3
(xxx =270~340,in increment of 5)
JKMSxxxM-60L-V-MX3 JKMSxxxM-60BL-V-MX3 JKMSxxxM-60L- MX3 JKMSxxxM-60BL -MX3
(xxx =270~340,in increment of 5)
Group 8

-26-
 JKMSxxxM-60H-V-MX3 JKMSxxxM-60HB-V-MX3 JKMSxxxM-60H-MX3 JKMSxxxM-60HB-MX3
(xxx =270~340,in increment of 5)
JKMSxxxM-60HL-V-MX3 JKMSxxxM-60HBL-V-MX3 JKMSxxxM-60HL-MX3 JKMSxxxM-60HBL-MX3
(xxx =270~340,in increment of 5)
Group 9
JKMxxxM-60H-TV JKMxxxM-60HL-TV JKMxxxM-60H-T JKMxxxM-60HL-T
(xxx =315~355,in increment of 5)
JKMxxxN-60H-TV JKMxxxN-60HL-TV JKMxxxN-60H-T JKMxxxN-60HL-T
(xxx =315~355,in increment of 5)
Group 10
JKMxxxPP-72 JKMxxxPP-72(Plus) JKMSxxxPP-72 JKMSxxxPP-72-J
JKMxxxPP-72-V JKMxxxPP-72(Plus)-V JKMSxxxPP-72-V JKMSxxxPP-72-V-J
JKMxxxPP-72B
(xxx =320~355,in increment of 5)
Group 11
JKMxxxPP-72H JKMxxxPP-72H-V JKMxxxPP-72HB
(xxx =330~380,in increment of 5)
Group 12
JKMSxxxPP-72-V-MX3 JKMSxxxPP-72B-V-MX3 JKMSxxxPP-72-MX3 JKMSxxxPP-72B-MX3
(xxx =320~355,in increment of 5)
JKMSxxxPP-72L-V-MX3 JKMSxxxPP-72BL-V-MX3 JKMSxxxPP-72L-MX3 JKMSxxxPP-72BL-MX3
(xxx =320~355,in increment of 5)
Group 13
JKMSxxxPP-72H-V-MX3 JKMSxxxPP-72HB-V-MX3 JKMSxxxPP-72H-MX3 JKMSxxxPP-72HB-MX3
(xxx =330~380,in increment of 5)
JKMSxxxPP-72HL-V-MX3 JKMSxxxPP-72HBL-V-MX3 JKMSxxxPP-72HL-MX3 JKMSxxxPP-72HBL-MX3
(xxx =330~380,in increment of 5)
Group 14
JKMxxxM-72 JKMxxxM-72(Plus) JKMSxxxM-72 JKMSxxxM-72-J
JKMxxxM-72-V JKMxxxM-72(Plus)-V JKMSxxxM-72-V JKMSxxxM-72-V-J
JKMxxxM-72B
(xxx =335~410，in increment of 5)
JKMxxxM-72L JKMxxxM-72L-V JKMxxxM-72BL
(xxx =335~410，in increment of 5)
Group 15
JKMxxxM-72H JKMxxxM-72H-V JKMxxxM-72HB
(xxx =335~425,in increment of 5)
JKMxxxM-72HL JKMxxxM-72HL-V JKMxxxM-72HBL
(xxx =335~425,in increment of 5)
Group 16
JKMSxxxM-72-V-MX3 JKMSxxxM-72B-V-MX3 JKMSxxxM-72-MX3 JKMSxxxM-72B-MX

-27-
(xxx =335~395,in increment of 5)
JKMSxxxM-72L-V-MX3 JKMSxxxM-72BL-V-MX3 JKMSxxxM-72L-MX3 JKMSxxxM-72BL-MX3
(xxx =335~395,in increment of 5)
Group 17
JKMSxxxM-72H-V-MX3 JKMSxxxM-72HB-V-MX3 JKMSxxxM-72H-MX3 JKMSxxxM-72HB-MX3
(xxx =335~395,in increment of 5)
JKMSxxxM-72HL-V-MX3 JKMSxxxM-72HBL-V-MX3 JKMSxxxM-72HL-MX3 JKMSxxxM-72HBL-MX3
(xxx =335~395,in increment of 5)
Group 18
JKMxxxM-72H-TV JKMxxxM-72HL-TV JKMxxxM-72H-T JKMxxxM-72HL-T
(xxx =375~425,in increment of 5)
JKMxxxN-72H-TV JKMxxxN-72HL-TV JKMxxxN-72H-T JKMxxxN-72HL-T
(xxx =375~425,in increment of 5)
Group 19
JKMxxxN-72H-MBB-TV JKMxxxN-72H-MBB-T
(xxx =390~420,in increment of 5)
Group 20
JKMxxxN-60H-MBB-TV JKMxxxN-60H-MBB-T
(xxx =330~350,in increment of 5)
Group 21
JKMxxxM-72H-MBB JKMxxxM-72H-MBB-V
(xxx =385~415,in increment of 5)
Group 22
JKMxxxM-60H-MBB JKMxxxM-60H-MBB-V
(xxx =320~345,in increment of 5)
Group 23
JKSM3-DACA-xxx JKSM3-DFCA-xxx
(xxx =400~440,in increment of 5)
Group 24
JKSM3-CACA-xxx JKSM3-CFCA-xxx
(xxx =335~370,in increment of 5)
Group 25
JKSM3-DCCA-xxx JKSM3-DHCA-xxx
(xxx =400~450,in increment of 5)
Group 26
JKSM3-CCCA-xxx JKSM3-CHCA-xxx
(xxx =340~380,in increment of 5)
Group 27
JKSN3-DCCA-xxx JKSN3-DHCA-xxx
(xxx =410~440,in increment of 5)
Group 28

-28-
 JKSN3-CCCA-xxx JKSN3-CHCA-xxx
(xxx =345~370,in increment of 5)
Group 29
JKMxxxM-72H-MBB-TV JKMxxxM-72H-MBB-T
(xxx =385~405,in increment of 5)
Group 30
JKMxxxM-60H-MBB-TV JKMxxxM-60H-MBB-T
(xxx =320~335,in increment of 5)
Group 31
JKMxxxM-78H-V JKMxxxM-78H
(xxx =405-445,in increment of 5)
Group 32
JKMxxxM-66H-V JKMxxxM-66H
(xxx =340-375,in increment of 5)
Group 33
JKMxxxM-78H-TV JKMxxxM-78H-T
(xxx =405-455,in increment of 5)
Group 34
JKMxxxM-66H-TV JKMxxxM-66H-T
(xxx =340-385,in increment of 5)
Group 35
JKMxxxN-78H-TV JKMxxxN-78H-T
(xxx =410-460,in increment of 5)
Group 36
JKMxxxN-66H-TV JKMxxxN-66H-T
(xxx =345-385,in increment of 5)
Group 37
JKMxxxM-78HB-V JKMxxxM-78HB
(xxx =405-435,in increment of 5)
Group 38
JKMxxxM-66HB-V JKMxxxM-66HB
(xxx =340-365,in increment of 5)
Group 39
JKMxxxM-7RL3-V JKMxxxM-7RL3 JKMxxxM-7RL3-V-J JKMxxxM-7RL3-J
(xxx = 430~470,in increment of 5)
Group 40
JKMxxxM-6RL3-V JKMxxxM-6RL3 JKMxxxM-6RL3-V-J JKMxxxM-6RL3-J
(xxx = 360~395,in increment of 5)
Group 41
JKMxxxM-7RL3-TV JKMxxxM-7RL3-T JKMxxxM-7RL3-TV-J JKMxxxM-7RL3-T-J
(xxx = 420~470,in increment of 5)

-29-
 Group 42
JKMxxxM-6RL3-TV JKMxxxM-6RL3-T JKMxxxM-6RL3-TV-J JKMxxxM-6RL3-T-J
(xxx = 355~395,in increment of 5)
Group 43
JKMxxxN-7RL3-TV JKMxxxN-7RL3-T JKMxxxN-7RL3-TV-J JKMxxxN-7RL3-T-J
(xxx = 425~470,in increment of 5)
Group 44
JKMxxxN-6RL3-TV JKMxxxN-6RL3-T JKMxxxN-6RL3-TV-J JKMxxxN-6RL3-T-J
(xxx = 355~395,in increment of 5)
Group 45
JKMxxxN-72H-MBB JKMxxxN-72H-MBB-V
(xxx = 385~425,in increment of 5)
Group 46
JKMxxxN-60H-MBB JKMxxxN-60H-MBB-V
(xxx = 320~350,in increment of 5)
Group 47
JKMxxxN-7RL3-V JKMxxxN-7RL3 JKMxxxN-7RL3-V-J JKMxxxN-7RL3-J
(xxx = 430~470,in increment of 5)
Group 48
JKMxxxN-6RL3-V JKMxxxN-6RL3 JKMxxxN-6RL3-V-J JKMxxxN-6RL3-J
(xxx = 360~395,in increment of 5)

Notes:
 PP: the eagle series module
 Plus: the eagle+ series module
 JKMS: the smart module
 V:module with 1500V
 H:half-cut series module
 L: large cell series module
 T/TV: transparent backsheet series module
 MX3: module with Z8S Junction Box
 MBB: nine busbar
 B: black backsheet
 RL3：large cell TR series module
Jinko Cell Junction
Wafer type Technology Module Type Cell
Module Number Box
STC condition: Normal mono- 158 5BB Mono-
p-type Mono: M Full cell: 1 60: A Normal: A
JKS facial: A facial: A
BSTC All black mono- 158 5BB Bi-
Poly: P Half cell: 2 72: B MX: B
condition: JKB facial: B facial: B
Transparent back 158 9BB Bi-
N-type Mono: N TR: 3 66: C MX3: C
sheet: C facial: C
Shingling: 4 78: D Bifacial dual 161 9BB Bi- EP: D

-30-
 glass: D facial: D

Appendix 2：Electrical Specifications

Rated
Rated Max.
Maximum Maximum Maximum Open- Short- Max.
output
Module Power at Power Power circuit circuit output
current
Type STC (Pmax, Voltage(Vmp Current(I Voltage(Vo Current(Is voltage
(Optimized
Wp) ,V) mp, A) c,V) c,A) (Optimize
) [A]:
d) [V]:
260 31.1 8.37 37.9 9.08
265 31.4 8.44 38.1 9.19
270 31.7 8.52 38.4 9.27
Group 1
275 32 8.61 38.7 9.38
Group 2
280 32.3 8.69 39 9.5
285 32.5 8.77 39.3 9.78
290 32.8 8.85 39.6 9.85
295 33.1 8.93 39.9 9.93
300 33.4 9 40.2 10.01
Group 2 305 33.6 9.09 40.5 10.09
310 33.9 9.16 40.8 10.16
315 34.1 9.25 41.1 10.24
260 31.1 8.37 37.9 9.08 12.0 33.6
265 31.4 8.44 38.1 9.19 12.0 33.6
270 31.7 8.52 38.4 9.27 12.0 33.6
Group 3
275 32 8.61 38.7 9.38 12.0 33.6
Group 4
280 32.3 8.69 39 9.5 12.0 33.6
285 32.5 8.77 39.3 9.78 12.0 33.6
290 32.8 8.85 39.6 9.85 12.0 33.6
295 33.1 8.93 39.9 9.93 12.0 33.6
300 33.4 9 40.2 10.01 12.0 33.6
Group 4 305 33.6 9.09 40.5 10.09 12.0 33.6
310 33.9 9.16 40.8 10.16 12.0 33.6
315 34.1 9.25 41.1 10.24 12.0 33.6
270 31.4 8.6 38.4 9.29
275 31.6 8.71 38.5 9.4
Group 5 280 31.8 8.81 38.6 9.51
Group 6 285 32 8.91 38.7 9.63
290 32.2 9.02 39.5 9.76
295 32.4 9.11 39.7 9.88

-31-
 300 32.6 9.21 40.1 9.98
305 32.8 9.3 40.3 10.07
310 33 9.4 40.5 10.15
315 33.2 9.49 40.7 10.23
320 33.4 9.59 40.9 10.31
325 33.6 9.68 41.1 10.5
330 33.8 9.77 41.3 10.61
335 34 9.86 41.5 10.73
340 34.2 9.95 41.7 10.82
345 34.4 10.03 41.9 10.91
350 34.6 10.12 42.1 11.00
270 31.4 8.6 38.4 9.29 12.0 33.6
275 31.6 8.71 38.5 9.4 12.0 33.6
280 31.8 8.81 38.6 9.51 12.0 33.6
285 32 8.91 38.7 9.63 12.0 33.6
290 32.2 9.02 39.5 9.76 12.0 33.6
295 32.4 9.11 39.7 9.88 12.0 33.6
300 32.6 9.21 40.1 9.98 12.0 33.6
Group 7
305 32.8 9.3 40.3 10.07 12.0 33.6
Group 8
310 33 9.4 40.5 10.15 12.0 33.6
315 33.2 9.49 40.7 10.23 12.0 33.6
320 33.4 9.59 40.9 10.31 12.0 33.6
325 33.6 9.68 41.1 10.5 12.0 33.6
330 33.8 9.77 41.3 10.61 12.0 33.6
335 34 9.86 41.5 10.73 12.0 33.6
340 34.2 9.95 41.7 10.82 12.0 33.6
315 32.7 9.63 39.9 9.99
320 32.9 9.73 40.1 10.07
325 33.1 9.82 40.3 10.15
330 33.24 9.93 40.39 10.25
Group 9
335 33.4 10.03 40.46 10.34
（P 型）
340 33.62 10.11 40.6 10.43
345 33.76 10.22 40.75 10.53
350 33.94 10.31 40.87 10.62
355 34.11 10.41 41 10.71
315 33 9.55 40.19 10.12
Group 9 320 33.17 9.65 40.32 10.23
（N 型） 325 33.38 9.74 40.43 10.32
330 33.51 9.85 40.56 10.43

-32-
 335 33.68 9.95 40.73 10.53
340 33.88 10.04 40.84 10.64
345 34.07 10.13 40.94 10.73
350 34.16 10.25 41.1 10.82
355 34.32 10.35 41.2 10.93
320 37.4 8.56 45.3 9.21
325 37.6 8.66 45.5 9.28
330 37.8 8.74 45.8 9.35
335 38 8.82 46.1 9.43
Group 10
340 38.2 8.91 46.5 9.54
345 38.4 8.99 46.9 9.63
350 38.6 9.07 47.2 9.71
355 38.9 9.13 47.5 9.79
330 37.8 8.74 45.8 9.35
335 38 8.82 46.1 9.43
340 38.2 8.91 46.5 9.54
345 38.4 8.99 46.9 9.63
350 38.6 9.07 47.2 9.71
Group 11 355 38.9 9.13 47.5 9.79
360 39.1 9.21 47.8 9.87
365 39.3 9.29 48.1 9.95
370 39.5 9.37 48.4 10.02
375 39.7 9.45 48.7 10.09
380 39.9 9.53 49 10.16
320 37.4 8.56 45.3 9.21 12.0 37.2
325 37.6 8.66 45.5 9.28 12.0 37.2
330 37.8 8.74 45.8 9.35 12.0 37.2
335 38 8.82 46.1 9.43 12.0 37.2
Group 12
340 38.2 8.91 46.5 9.54 12.0 37.2
345 38.4 8.99 46.9 9.63 12.0 37.2
350 38.6 9.07 47.2 9.71 12.0 37.2
355 38.9 9.13 47.5 9.79 12.0 37.2
330 37.8 8.74 45.8 9.35 12.0 37.2
335 38 8.82 46.1 9.43 12.0 37.2
340 38.2 8.91 46.5 9.54 12.0 37.2
Group 13 345 38.4 8.99 46.9 9.63 12.0 37.2
350 38.6 9.07 47.2 9.71 12.0 37.2
355 38.9 9.13 47.5 9.79 12.0 37.2
360 39.1 9.21 47.8 9.87 12.0 37.2

-33-
 365 39.3 9.29 48.1 9.95 12.0 37.2
370 39.5 9.37 48.4 10.02 12.0 37.2
375 39.7 9.45 48.7 10.09 12.0 37.2
380 39.9 9.53 49 10.16 12.0 37.2
335 38.4 8.72 46.9 9.79
340 38.7 8.79 47.1 9.81
345 38.9 8.87 47.3 9.85
350 39.1 8.94 47.5 9.88
355 39.3 9.04 47.8 9.93
360 39.5 9.12 48 10.02
365 39.7 9.2 48.2 10.09
370 39.9 9.28 48.5 10.15
375 40.2 9.33 48.7 10.23
Group 14
380 40.5 9.39 48.9 10.3
Group 15
385 40.8 9.44 49.1 10.38
390 41.1 9.49 49.3 10.46
395 41.4 9.55 49.5 10.54
400 41.7 9.6 49.8 10.61
405 42 9.65 50.1 10.69
410 42.3 9.7 50.3 10.76
415 42.6 9.75 50.6 10.82
420 42.9 9.80 50.9 10.88
425 43.2 9.85 51.2 10.94
335 38.4 8.72 46.9 9.79 12.0 37.2
340 38.7 8.79 47.1 9.81 12.0 37.2
345 38.9 8.87 47.3 9.85 12.0 37.2
350 39.1 8.94 47.5 9.88 12.0 37.2
355 39.3 9.04 47.8 9.93 12.0 37.2
360 39.5 9.12 48 10.02 12.0 37.2
Group 16
365 39.7 9.2 48.2 10.09 12.0 37.2
Group 17
370 39.9 9.28 48.5 10.15 12.0 37.2
375 40.2 9.33 48.7 10.23 12.0 37.2
380 40.5 9.39 48.9 10.3 12.0 37.2
385 40.8 9.44 49.1 10.38 12.0 37.2
390 41.1 9.49 49.3 10.46 12.0 37.2
395 41.4 9.55 49.5 10.54 12.0 37.2
375 39.25 9.56 47.92 9.92
Group 18
380 39.36 9.66 47.96 10.02
（P 型）
385 39.5 9.76 48.1 10.08

-34-
 390 39.62 9.84 48.14 10.17
395 39.83 9.92 48.26 10.23
400 40.01 10 48.35 10.32
405 40.19 10.08 48.45 10.42
410 40.38 10.16 48.56 10.51
415 40.5 10.25 48.64 10.61
420 40.65 10.33 48.74 10.7
375 39.32 9.54 48.1 10.07
380 39.43 9.64 48.2 10.17
385 39.53 9.74 48.31 10.26
390 39.64 9.84 48.4 10.36
395 39.74 9.94 48.5 10.45
Group 18
400 39.85 10.04 48.63 10.54
（N 型）
405 39.99 10.13 48.7 10.65
410 40.09 10.23 48.8 10.75
415 40.22 10.32 48.9 10.86
420 40.32 10.42 49 10.96
425 40.43 10.51 49.1 11.07
390 39.64 9.84 48.4 10.36
395 39.74 9.94 48.5 10.45
400 39.85 10.04 48.63 10.54
Group 19 405 39.99 10.13 48.7 10.65
410 40.09 10.23 48.8 10.75
415 40.22 10.32 48.9 10.86
420 40.31 10.42 49 10.96
330 33.51 9.85 40.56 10.43
335 33.68 9.95 40.73 10.53
Group 20 340 33.88 10.04 40.84 10.64
345 34.07 10.13 40.94 10.73
350 34.16 10.25 41.1 10.82
385 40.66 9.47 47.9 10.19
390 40.76 9.57 48.05 10.24
395 40.85 9.67 48.2 10.3
Group 21 400 40.95 9.77 48.35 10.36
405 41.04 9.87 48.5 10.42
410 41.13 9.97 48.65 10.48
415 41.26 10.06 48.8 10.54
320 33.76 9.48 39.87 10.18
Group 22
325 33.89 9.59 40.02 10.24

-35-
 330 34.03 9.7 40.17 10.3
335 34.15 9.81 40.32 10.36
340 34.28 9.92 40.47 10.42
345 34.4 10.03 40.62 10.48
400 42.97 9.31 52 9.99
405 43.13 9.39 52.1 10.05
410 43.25 9.48 52.2 10.11
415 43.42 9.56 52.3 10.17
Group 23 420 43.57 9.64 52.4 10.23
425 43.73 9.72 52.5 10.29
430 43.88 9.80 52.60 10.35
435 44.03 9.88 52.7 10.41
440 44.18 9.96 52.80 10.47
335 36.55 9.17 43.9 9.71
340 36.65 9.28 44 9.79
345 36.75 9.39 44.1 9.87
350 36.85 9.5 44.2 9.95
Group 24
355 36.95 9.61 44.30 10.03
360 37.04 9.72 44.40 10.11
365 37.14 9.83 44.50 10.19
370 37.23 9.94 44.60 10.27
400 43.3 9.24 52 9.86
405 43.41 9.33 52.1 9.91
410 43.53 9.42 52.2 9.96
415 43.64 9.51 52.3 10.01
420 43.75 9.6 52.4 10.07
Group 25 425 43.86 9.69 52.5 10.16
430 43.97 9.78 52.6 10.25
435 44.08 9.87 52.7 10.34
440 44.18 9.96 52.80 10.38
445 44.28 10.05 52.90 10.47
450 44.38 10.14 53.00 10.56
340 36.65 9.28 44 9.87
345 36.75 9.39 44.1 9.93
350 36.85 9.5 44.2 9.99
Group 26 355 36.95 9.61 44.30 10.05
360 37.04 9.72 44.40 10.11
365 37.14 9.83 44.50 10.22
370 37.23 9.94 44.60 10.33

-36-
 375 37.32 10.05 44.70 10.44
380 37.44 10.15 44.80 10.55
400 43.3 9.24 52 10.05
405 43.41 9.33 52.1 10.1
410 43.53 9.42 52.2 10.15
415 43.64 9.51 52.3 10.2
Group 27 420 43.75 9.6 52.4 10.25
425 43.86 9.69 52.5 10.3
430 43.97 9.78 52.6 10.35
435 44.08 9.87 52.7 10.40
440 44.18 9.96 52.80 10.45
340 36.65 9.28 44 10.05
345 36.75 9.39 44.1 10.11
350 36.85 9.5 44.2 10.18
Group 28 355 36.95 9.61 44.3 10.24
360 37.04 9.72 44.4 10.31
365 37.14 9.83 44.50 10.37
370 37.23 9.94 44.60 10.44
385 40.66 9.47 48.47 10.31
390 40.76 9.57 48.57 10.38
Group 29 395 40.85 9.67 48.67 10.45
400 40.95 9.77 48.77 10.52
405 41.04 9.87 48.87 10.59
320 33.76 9.48 40.31 10.22
325 33.89 9.59 40.43 10.29
Group 30
330 34.03 9.7 40.55 10.36
335 34.15 9.81 40.67 10.43
405 42.91 9.44 51.07 10.20
410 43.03 9.53 51.16 10.27
415 43.10 9.63 51.25 10.34
420 43.17 9.73 51.34 10.41
Group 31 425 43.23 9.83 51.43 10.48
430 43.49 9.89 51.52 10.57
435 43.55 9.99 51.61 10.67
440 43.65 10.08 51.70 10.77
445 43.72 10.18 52.04 10.84
340 36.56 9.30 43.24 10.20
Group 32 345 36.67 9.41 43.32 10.27
350 36.77 9.52 43.41 10.34

-37-
 355 36.87 9.63 43.49 10.41
360 36.97 9.74 43.58 10.48
365 37.06 9.85 43.66 10.55
370 37.15 9.96 43.75 10.62
375 37.24 10.07 44.02 10.69
405 42.90 9.44 51.55 10.15
410 43.03 9.53 51.58 10.20
415 43.20 9.61 51.61 10.28
420 43.35 9.69 51.64 10.36
425 43.50 9.77 51.67 10.44
Group 33 430 43.66 9.85 51.70 10.52
435 43.85 9.92 51.80 10.60
440 43.92 10.02 51.90 10.68
445 43.98 10.12 52.00 10.78
450 44.04 10.22 52.10 10.87
455 44.14 10.31 52.20 10.96
340 36.72 9.26 43.56 10.12
345 36.82 9.37 43.64 10.20
350 36.92 9.48 43.67 10.28
355 37.02 9.59 43.71 10.36
360 37.12 9.70 43.75 10.44
Group 34
365 37.21 9.81 43.83 10.52
370 37.30 9.92 43.92 10.60
375 37.39 10.03 44.00 10.68
380 37.48 10.14 44.11 10.76
385 37.57 10.25 44.17 10.84
410 42.71 9.60 51.58 10.42
415 42.79 9.70 51.61 10.51
420 42.86 9.80 51.64 10.60
425 42.93 9.90 51.67 10.69
430 43.00 10.00 51.70 10.78
Group 35
435 43.07 10.10 51.80 10.87
440 43.14 10.20 51.90 10.96
445 43.21 10.30 52.00 11.05
450 43.27 10.40 52.10 11.14
455 43.34 10.50 52.20 11.23
460 43.40 10.60 52.30 11.32
345 36.82 9.37 43.64 10.51
Group 36
350 36.93 9.48 43.67 10.60

-38-
 355 37.02 9.59 43.70 10.69
360 37.12 9.70 43.72 10.78
365 37.21 9.81 43.75 10.87
370 37.30 9.92 43.83 10.96
375 37.39 10.03 43.92 11.05
380 37.48 10.14 44.01 11.14
385 37.57 10.25 44.11 11.23
405 43.23 9.37 51.55 10.01
410 43.3 9.47 51.58 10.11
415 43.37 9.57 51.61 10.21
Group 37 420 43.44 9.67 51.64 10.31
425 43.51 9.77 51.67 10.41
430 43.57 9.87 51.7 10.51
435 43.64 9.97 51.73 10.61
340 36.56 9.3 43.6 10.01
345 36.63 9.42 43.63 10.13
350 36.69 9.54 43.65 10.25
Group 38
355 36.76 9.66 43.68 10.37
360 36.81 9.78 43.7 10.49
365 36.87 9.9 43.73 10.61
430 42.41 10.14 51.10 10.96
435 42.52 10.23 51.20 11.05
440 42.64 10.32 51.30 11.14
445 42.75 10.41 51.40 11.23
Group 39 450 42.86 10.50 51.50 11.32
455 42.97 10.59 51.60 11.41
460 43.08 10.68 51.70 11.50
465 43.18 10.77 51.92 11.59
470 43.28 10.86 52.14 11.68
360 35.90 10.03 43.24 10.85
365 36.00 10.14 43.32 10.94
370 36.10 10.25 43.41 11.03
375 36.20 10.36 43.49 11.12
Group 40
380 36.30 10.47 43.58 11.21
385 36.39 10.58 43.66 11.30
390 36.49 10.69 43.75 11.39
395 36.58 10.80 43.93 11.48
420 42.77 9.82 51.10 10.63
Group 41
425 42.85 9.92 51.20 10.72

-39-
 430 42.92 10.02 51.30 10.81
435 42.99 10.12 51.40 10.90
440 43.06 10.22 51.50 10.99
445 43.13 10.32 51.60 11.08
450 43.19 10.42 51.70 11.17
455 43.25 10.52 51.80 11.26
460 43.32 10.62 51.90 11.35
465 43.38 10.72 52.00 11.44
470 43.44 10.82 52.10 11.53
355 36.49 9.73 43.32 10.45
360 36.55 9.85 43.41 10.55
365 36.61 9.97 43.49 10.65
370 36.67 10.09 43.58 10.75
Group 42 375 36.73 10.21 43.66 10.85
380 36.79 10.33 43.75 10.95
385 36.85 10.45 43.83 11.05
390 36.90 10.57 43.92 11.15
395 36.95 10.69 44.00 11.25
425 43.15 9.85 51.20 10.62
430 43.22 9.95 51.30 10.71
435 43.29 10.05 51.40 10.80
440 43.36 10.15 51.50 10.89
445 43.42 10.25 51.60 10.98
Group 43
450 43.48 10.35 51.70 11.07
455 43.54 10.45 51.80 11.16
460 43.60 10.55 51.90 11.25
465 43.66 10.65 52.00 11.34
470 43.72 10.75 52.10 11.43
355 36.38 9.76 43.32 10.54
360 36.44 9.88 43.41 10.68
365 36.50 10.00 43.49 10.80
370 36.56 10.12 43.58 10.92
Group 44 375 36.62 10.24 43.66 11.04
380 36.68 10.36 43.75 11.16
385 36.74 10.48 43.83 11.28
390 36.80 10.60 43.92 11.40
395 36.85 10.72 44.00 11.52
385 39.65 9.71 47.90 10.42
Group 45
390 39.76 9.81 48.05 10.48

-40-
 395 39.86 9.91 48.20 10.54
400 39.96 10.01 48.35 10.60
405 40.06 10.11 48.50 10.66
410 40.16 10.21 48.65 10.72
415 40.26 10.31 48.80 10.78
420 40.35 10.41 48.95 10.84
425 40.44 10.51 49.10 10.90
320 33.03 9.69 39.95 10.40
325 33.13 9.81 40.08 10.46
330 33.24 9.93 40.21 10.52
Group 46 335 33.37 10.04 40.34 10.58
340 33.47 10.16 40.47 10.64
345 33.60 10.27 40.60 10.70
350 33.72 10.38 40.73 10.76
430 42.45 10.13 51.10 10.96
435 42.57 10.22 51.20 11.05
440 42.68 10.31 51.30 11.14
445 42.79 10.40 51.40 11.23
Group 47 450 42.90 10.49 51.50 11.32
455 43.01 10.58 51.60 11.41
460 43.12 10.67 51.70 11.50
465 43.22 10.76 51.90 11.59
470 43.32 10.85 52.10 11.68
360 35.72 10.08 43.24 10.93
365 35.79 10.20 43.32 11.03
370 35.86 10.32 43.41 11.13
375 35.92 10.44 43.49 11.23
Group 48
380 35.99 10.56 43.58 11.33
385 36.05 10.68 43.66 11.43
390 36.11 10.80 43.75 11.53
395 36.18 10.92 43.92 11.63

-41-
Note
___________________________________________________________________________

___________________________________________________________________________

___________________________________________________________________________

___________________________________________________________________________

___________________________________________________________________________

___________________________________________________________________________

___________________________________________________________________________

___________________________________________________________________________

___________________________________________________________________________

-42-
Global Sales & Marketing Center Jiangxi Manufacture Base Zhejiang Manufacture Base
Jinko Building No.1 Jinko Road, No.58 Yuanxi Road,
#99 Shouyang Road, Jingan District, Shangrao Economic Development Zone, Haining Yuanhua Industrial Park,
Shanghai, China 200027 Jiangxi Province, China 334100 Zhejiang Province, China 314416
Tel: +86 21 5183 8777 Tel:+86 793 858 8188 Tel: +86 573 8798 5678
Fax: +86 21 5180 8600 Fax:+86 793 846 1152 Fax: +86 573 8787 1070

www.jinkosolar.com | Technic Support: [email protected] | After-sales: [email protected]