M3G150-NA07-B0 EC motor

for barn ventilation

ebm-papst Mulfingen GmbH & Co. KG

Bachmühle 2 · D-74673 Mulfingen
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]
www.ebmpapst.com
Limited partnership · Headquarters Mulfingen
Amtsgericht (court of registration) Stuttgart · HRA 590344

General partner Elektrobau Mulfingen GmbH · Headquarters Mulfingen

Amtsgericht (court of registration) Stuttgart · HRB 590142

Nominal data

Type M3G150-NA07-B0
Motor M3G150-NA

Phase 3~
Nominal voltage VAC 400
Nominal voltage range VAC 380 .. 480
Frequency Hz 50/60

Method of obtaining data ml

Status prelim.
Speed (rpm) min-1 580
Power consumption W 1530
Power output W 1380
Current draw A 2.4
Rated torque Ncm 2300
Min. ambient temperature °C -40
Max. ambient temperature °C 40
ml = Max. load · me = Max. efficiency · fa = Free air · cs = Customer specification · ce = Customer equipment
Subject to change

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 1 / 8

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
 M3G150-NA07-B0 EC motor
for barn ventilation

Technical description

Weight 27.9 kg
Motor size 150
Rotor surface Painted black
Electronics housing material Die-cast aluminum, painted gray
Direction of rotation Counterclockwise, viewed toward rotor
Degree of protection IP55
Insulation class "F"
Moisture (F) / Environmental (H) H2+
protection class
Ambient temperature note Occasional start-up at temperatures between -40°C and -25°C is permitted. For
continuous operation at ambient temperatures below -25°C (such as refrigeration
applications), use must be made of a fan design with special low-temperature bearings.
Max. permitted ambient temp. +80 °C
for motor (transport/storage)
Min. permitted ambient temp. for -40 °C
motor (transport/storage)
Installation position Shaft horizontal or rotor on bottom; rotor on top on request
Condensation drainage holes On rotor side
Mode S1
Motor bearing Ball bearing; (sealed)
Technical features - Operation and alarm display with LED
- External 15-50 VDC input (parameterization)
- Alarm relay
- Integrated PI controller
- Configurable inputs/outputs (I/O)
- MODBUS V6.0
- Motor current limitation
- RFID - ISO 15693 compatible
- RS-485 MODBUS-RTU
- Soft start
- Voltage output 3.3-24 VDC, Pmax = 800 mW
- Control interface with SELV potential safely disconnected from the mains
- Thermal overload protection for electronics/motor
- Line undervoltage / phase failure detection
Touch current according to IEC <= 3.5 mA
60990 (measuring circuit Fig. 4,
TN system)
Electrical hookup Terminal box
Motor protection Electronic motor protection
Protection class I (with customer connection of protective earth)
Conformity with standards EN 61800-5-1; CE
Approval CSA C22.2 No. 77 + CAN/CSA-E60730-1; EAC; UL 1004-7 + 60730-1

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 2 / 8

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
 M3G150-NA07-B0 EC motor
for barn ventilation

Product drawing

1 Direction of rotation counterclockwise, viewed toward shaft

2 Max. clearance for screw 20 mm
3 Cable diameter min. 4 mm, max. 10 mm, tightening torque 2±0.3 Nm
4 Tightening torque 1.5 ± 0.2 Nm
Fa Max. permissible axial load: 370 N
Fr Max. permissible radial load: 70 N
Accessory part: Fastening set 38923-1-5191 for impeller installation included in scope of delivery
Impeller 60702-1-3234 accessory part not included in scope of delivery
S Center of gravity

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 3 / 8

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
 M3G150-NA07-B0 EC motor
for barn ventilation

Connection diagram

No. Conn. Designation Function/assignment

CON1 L1, L2, L3 Power supply, phase, see nameplate for voltage range
PE PE Protective earth
CON2 RSA RS485 interface for MODBUS, RSA; SELV
CON2 RSB RS485 interface for MODBUS, RSB; SELV
CON2 GND Reference ground for control interface, SELV
CON2 IO1 Function parameterizable (see “Optional interface functions” table)
Factory setting:
Digital input - high active, function: Disable input, SELV
- inactive: Pin open or applied voltage < 1.5 VDC
- active: applied voltage 3.5-50 VDC
Reset function: Triggering of error reset on change of state from "enabled" to "disabled"
CON2 IO2 Function parameterizable (see “Optional interface functions” table)
Factory setting:
Analog input 0-10 V / PWM, Ri=100 kΩ, function: Set value
Characteristic curve parameterizable (see input characteristic curve P1-IN), SELV
CON2 IO3 Function parameterizable (see “Optional interface functions” table)
Factory setting:
Analog output 0-10 V, max. 5 mA, function: Fan modulation level
Characteristic curve parameterizable (see output characteristic curve P3-OUT), SELV
CON2 Vout Voltage output 3.3-24 VDC ±5%, Pmax=800 mW, voltage parameterizable
Factory setting: 10 VDC
short-circuit-proof, supply for external devices, SELV
alternatively: 15-50 VDC input for parameterization via MODBUS without line voltage
CON2 COM Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1) / min. 10
mA, reinforced insulation on supply side and on control interface side
CON2 NC Status relay, floating status contact, break for failure
LED green: status = good, ready for operation
orange: status = warning
red: status = failure
P1-IN Input characteristic curve
P3-OUT Output characteristic curve

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 4 / 8

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
 ○ configurable option

For further information and additional functions see EC Control Software, Fan-Set-App,

D101 [...]
D147 [...]
D104 [...]
D12E [...]
D148 [...]
D16C [...]
D16A [...]
(selected directly
via IO mode)
(selected directly
D130 [0]
D130 [1]
D130 [2]
D130 [5]
D00C [1]
D130 [4]

via IO mode)
or MODBUS Parameter Specification V6.0
INPUT OUTPUT

inverse
M3G150-NA07-B0

configurable IO
functions: normal /
Terminal/plug assignment

MODBUS
Register for IO
mode

source: set value

source: sensor value
switch: parameter set: #1 / #2
switch: control function: heating (pos.) /
switch: direction of rotation: cw / ccw

cooling (neg.)
signal: actual speed
signal: system modulation level %
signal: remote control output 0-10V
pulse input for auto-adressing
pulse output for auto-adressing

switch: set value source

switch: fan enable / disable
signal: tach out
signal: diagnostics out
signal: fan modulation level %
CON2 configurable IO mode electrical specification configuration
Din1 (active high): digital input not active: pin open or applied voltage < 1,5VDC D158 [0]
○ ○ ○ ○ ○ ○
active: applied voltage 3,5-50VDC, SELV
IO1 ○ Ain1 0-10V/PWM: analog input Ri=100K, characteristic curve parameterizable, fPWM=1k..10KHz, SELV D158 [2] ○ ○
○ Tach out (open collector output) Umax=50VDC, Imax=20mA, SELV D158 [5] ○
○ Diagnostics out (open collector output) Umax=50VDC, Imax=20mA, SELV D158 [6] ○
○ Din2 (active high): digital input not active: pin open or applied voltage < 1,5VDC D159 [0]
○ ○ ○ ○ ○
active: applied voltage 3,5-50VDC, SELV
IO2
Ain2 0-10V/PWM: analog input Ri=100K, characteristic curve parameterizable, fPWM=1k..10KHz, SELV D159 [2]
○ ○

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 5 / 8

○ Ain2 4-20mA: analog input Ri=125R, characteristic curve parameterizable, SELV D159 [3]
○ Din3 (active high): digital input not active: pin open or applied voltage < 1,5VDC D15A [0]
EC motor
for barn ventilation

active: applied voltage 3,5-50VDC, SELV

○ Din3 (active low): digital input
○ ○ ○ ○ ○
active: pin open or applied voltage 3,5-50VDC D15A [1]
not active: applied voltage < 1,5VDC, SELV
○ PWMin3: digital input 40Hz - 10kHz, characteristics parameterizable D15A [7]
IO3
not active: pin open or applied voltage 3,5-50VDC ○
active: applied voltage < 1,5VDC, SELV
Aout3 0-10V: analog output function parameterizable, max. 5mA, max output frequency 300Hz, SELV D15A [4] ○ ○ ○ ○ ○
○ Tacho out (pulses), analog output 0-10V max. 5mA, max output frequency 300Hz, SELV D15A [5] ○
○ Diagnostics out (pulses) 0-10V max. 5mA, max output frequency 300Hz, SELV D15A [6] ○
RSA RS485 bus connection, MODBUS RTU, specification V6.0, SELV
○ ○ ○ ○ ○ ○
RSB
voltage output voltage parameterizable 3,3...24VDC +/- 5,5%, Pmax=800mW, short-circuit-proof, D16E [...]
Vout
supply for external devices, SELV
alternatively: Input auxillary power supply for 15...50VDC
parameter-ization via RS485/MODBUS RTU without line
voltage

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
 M3G150-NA07-B0 EC motor
for barn ventilation

Curves: Air performance without diffuser

in. wg
Pa

50 4
0.2

ρ = 1.15 kg/m³ ± 2 %
Measurement: LU-195180-1

Air performance measured according to ISO

40
5801 installation category A. For detailed
0.15

8 information on the measurement setup,

contact ebm-papst. Intake sound level:
3 Sound power level according to ISO 13347 /
sound pressure level measured at 1 m
distance from fan axis. The values given are
30 valid under the specified measuring
conditions and may vary due to conditions
7 of installation. For deviations from the
0.1

standard configuration, the parameters

12 have to be checked on the installed unit.

20 2
The measurement was carried out with the
11
6 ebm-papst impeller 60702-1-3234
16
0.05

10 10
15

14

13 920000 525000 1 cfm

pfs

0 5000 10000 15000

qv 10000 20000 30000 40000 m³/h

Measured values
Wired U f n Ped I LpAin LwAin LwAout qV pfs qV pfs
V Hz min-1 W A dB(A) dB(A) dB(A) m3/h Pa cfm in. wg
1 3~ 230 50 580 1310 3.66 71 79 80 46970 0 27645 0.00
2 3~ 230 50 580 1415 3.94 71 79 80 43585 20 25655 0.08
3 3~ 230 50 580 1477 4.10 71 79 80 40755 35 23990 0.14
4 3~ 230 50 580 1530 4.25 71 79 80 37480 50 22060 0.20
5 3~ 230 50 500 840 2.34 67 76 77 40490 0 23830 0.00
6 3~ 230 50 500 906 2.52 67 75 76 37570 16 22115 0.06
7 3~ 230 50 500 946 2.62 67 75 76 35135 26 20680 0.10
8 3~ 230 50 500 982 2.71 67 76 76 32310 37 19015 0.15
9 3~ 230 50 400 430 1.20 62 70 71 32395 0 19065 0.00
10 3~ 230 50 400 464 1.29 62 70 71 30060 10 17690 0.04
11 3~ 230 50 400 484 1.34 62 70 70 28110 17 16545 0.07
12 3~ 230 50 400 503 1.39 62 70 70 25850 24 15215 0.10
13 3~ 230 50 300 181 0.51 54 63 64 24295 0 14300 0.00
14 3~ 230 50 300 196 0.54 54 63 63 22545 6 13270 0.02
15 3~ 230 50 300 204 0.57 54 63 63 21080 9 12410 0.04
16 3~ 230 50 300 212 0.59 54 63 63 19385 13 11410 0.05
Wired = Wiring · U = Voltage · f = Frequency · n = Speed (rpm) · Ped = Power consumption · I = Current draw · LpAin = Sound pressure level intake side · LwAin = Sound power level intake side
LwAout = Sound power level outlet side · qV = Air flow · pfs = Pressure increase

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 6 / 8

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
 M3G150-NA07-B0 EC motor
for barn ventilation

Curves: Air performance with diffuser

in. wg
Pa

70 4

ρ = 1.15 kg/m³ ± 2 %
0.25

60
Measurement: LU-195181-1

Air performance measured according to ISO

8 5801 installation category A. For detailed
50 3 information on the measurement setup,
0.2

contact ebm-papst. Intake sound level:

Sound power level according to ISO 13347 /
sound pressure level measured at 1 m
distance from fan axis. The values given are
40 valid under the specified measuring
0.15

7 conditions and may vary due to conditions of

installation. For deviations from the standard
12 configuration, the parameters have to be
checked on the installed unit.
30

2 The measurement was carried out with the

0.1

11
20 ebm-papst impeller 60702-1-3234
16 6
15
0.05

10
10
14

13 9 5 1
pfs

0 5000 10000 15000 20000 25000 30000 cfm

qv 10000 20000 30000 40000 50000 m³/h

Measured values
Wired U f n Ped I LpAin LwAin LwAout qV pfs qV pfs
V Hz min-1 W A dB(A) dB(A) dB(A) m3/h Pa cfm in. wg
1 3~ 230 50 580 914 2.69 73 81 84 54895 0 32310 0.00
2 3~ 230 50 580 1173 3.33 71 79 83 49005 25 28840 0.10
3 3~ 230 50 580 1379 3.85 71 79 82 42920 50 25260 0.20
4 3~ 230 50 580 1530 4.25 71 79 82 37590 70 22125 0.28
5 3~ 230 50 500 586 1.72 69 77 81 47320 0 27855 0.00
6 3~ 230 50 500 751 2.13 67 76 79 42245 18 24865 0.07
7 3~ 230 50 500 884 2.47 67 75 78 37000 37 21780 0.15
8 3~ 230 50 500 965 2.67 67 75 78 32405 52 19075 0.21
9 3~ 230 50 400 300 0.88 64 71 75 37860 0 22280 0.00
10 3~ 230 50 400 385 1.09 62 70 73 33795 12 19890 0.05
11 3~ 230 50 400 452 1.26 61 69 73 29600 24 17420 0.10
12 3~ 230 50 400 494 1.37 61 70 73 25925 33 15260 0.13
13 3~ 230 50 300 127 0.37 56 64 68 28395 0 16710 0.00
14 3~ 230 50 300 162 0.46 55 63 66 25345 7 14920 0.03
15 3~ 230 50 300 191 0.53 54 62 65 22200 13 13065 0.05
16 3~ 230 50 300 208 0.58 54 62 66 19445 19 11445 0.08
Wired = Wiring · U = Voltage · f = Frequency · n = Speed (rpm) · Ped = Power consumption · I = Current draw · LpAin = Sound pressure level intake side · LwAin = Sound power level intake side
LwAout = Sound power level outlet side · qV = Air flow · pfs = Pressure increase

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 7 / 8

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
 M3G150-NA07-B0 EC motor
for barn ventilation

Curves: Speed (rpm)

2.600 1.300
6,4
6,2 2.500 1.250

6 2.400 1.200
5,8 2.300 1.150
5,6
2.200 1.100
5,4
5,2 2.100 1.050

5 2.000 1.000
4,8
1.900 950
4,6
1.800 900
4,4
4,2 1.700 850

4 1.600 800
3,8 1.500 750
3,6
1.400 700
3,4
n [1/min]
P1 [W]
I1 [A]

1.300 650
3,2
3 1.200 600
2,8 1.100 550
2,6
1.000 500
2,4
2,2 900 450

2 800 400
1,8 700 350
1,6
600 300
1,4
1,2 500 250

1 400 200
0,8
300 150
0,6
200 100
0,4
0,2 100 50

0 0
0 200 400 600 800 1.000 1.200 1.400 1.600 1.800 2.000 2.200 2.400 2.600 2.800 3.000 3.200
Md [Ncm]

Item no. 56852-5-9980 · ENU · Change 204336 · Approved 2019-09-13 · Page 8 / 8

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com