Technical Data Sheet

Approved 23820;23840 1 23820 epoxy ^(ValidationDate) 1

Penguard EXA

Product description
This is a two component polyamine cured epoxy coating. It is an aluminium pigmented product. It is a fast
drying, abrasion resistant, high solids, high build product. Can be used as primer, mid coat, finish coat or as
single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and
aged coating surfaces. It can be applied at sub zero surface temperatures.

Typical use
Protective:
Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed.
Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment.
Other

Colours
aluminium, aluminium red toned

Product data
Property Test/Standard Description
Solids by volume ISO 3233 72 ± 2 %
Gloss level (GU 60 °) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 28,5 °C
VOC-US/Hong Kong US EPA method 24 (tested) 260 g/l
VOC-EU IED (2010/75/EU) (calculated) 269 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 277 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Film thickness per coat

Typical recommended specification range

Dry film thickness 100 - 200 μm

Wet film thickness 140 - 280 μm
Theoretical spreading rate 7,2 - 3,6 m²/l

Date of issue: 24 May 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard EXA

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1)

Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)

Application
Application methods
The product can be applied by

Spray: Use airless spray.

Brush: Recommended for stripe coating and small areas, care must be taken to achieve the
specified dry film thickness.
Roller: May be used for small areas. Not recommended for first primer coat. Care must be taken
to achieve the specified dry film thickness.

Product mixing ratio (by volume)

Penguard EXA Comp A 4 part(s)

Penguard EXA Comp B 1 part(s)

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Guiding data for airless spray

Nozzle tip (inch/1000): 17-23

Pressure at nozzle (minimum): 200 bar/2900 psi

Date of issue: 24 May 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard EXA

Drying and Curing time

Substrate temperature -5 °C 0 °C 5 °C 10 °C 23 °C 40 °C

Surface (touch) dry 10 h 8h 5h 4h 2 h 1 h

Walk-on-dry 39 h 26 h 19 h 9h 5 h 2 h
Dry to over coat, minimum 39 h 26 h 19 h 9h 5 h 2 h
Dried/cured for service 21 d 14 d 10 d 7 d 3 d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Pot life 1h

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 140 °C

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: inorganic zinc silicate shop primer, epoxy, epoxy mastic, zinc epoxy, zinc silicate
Subsequent coat: acrylic, epoxy, polyurethane, polysiloxane

Packaging (typical)

Date of issue: 24 May 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard EXA

Volume Size of containers

(litres) (litres)

Penguard EXA Comp A 16 20

Penguard EXA Comp B 4 5

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Penguard EXA Comp A 24 month(s)
Penguard EXA Comp B 24 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

Date of issue: 24 May 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard EXA

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 24 May 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
 Technical Data Sheet

Approved 612;617 1 617 epoxy ^(ValidationDate) 1

Penguard Primer

Product description
This is a two component, polyamide cured, high molecular weight epoxy coating. Designed as a primer for new
construction. Can be used as primer as a part of a complete system in atmospheric and immersed environments.
Suitable for properly prepared carbon steel, stainless steel, aluminium, concrete, galvanised steel, shop primed
steel and thermally sprayed zinc substrates.

Typical use
Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed.
Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment.
Other

Colours
grey, red

Product data
Property Test/Standard Description
Solids by volume ISO 3233 51 ± 2 %
Gloss level (GU 60 °) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 25 °C
Density calculated 1,24 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 440 g/l
VOC-EU IED (2010/75/EU) (calculated) 456 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 415 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Film thickness per coat

Typical recommended specification range

Dry film thickness 40 - 60 μm

Wet film thickness 80 - 120 μm
Theoretical spreading rate 12,8 - 8,5 m²/l

Date of issue: 10 May 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Primer

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1)

Stainless steel The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using approved non-
or bonded fibre machine or hand metallic abrasive media which is
abrasive pads to impart a scratch suitable to achieve a sharp and
pattern to the surface and to remove angular surface profile.
all polish from the surface.
Aluminium The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using approved non-
or bonded fibre machine or hand metallic abrasive media which is
abrasive pads to impart a scratch suitable to achieve a sharp and
pattern to the surface and to remove angular surface profile.
all polish from the surface.
Galvanised steel The surface shall be clean, dry and Light brush blasting using non-
appear with a rough and dull profile. metallic abrasive leaving a clean,
rough and even pattern.
Shop primed steel Dry, clean and intact shop primer. Abrasive swept or alternatively
blasted to Sa 2 (ISO 8501-1) of at
least 70 % of the surface.
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)
Concrete Moisture content maximum 5 %. Minimum 4 weeks curing. Moisture
Mechanically prepare the existing content maximum 5 %. Prepare the
concrete surface by scabbling, needle surface by means of enclosed blast
gun, mechanical disc grinding. shot or diamond grinding and other
appropriate means to abrade the
surrounding concrete and to remove
laitance.

Application
Application methods
The product can be applied by

Spray: Use airless spray.

Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.

Product mixing ratio (by volume)

Penguard Primer Comp A 4 part(s)

Penguard Comp B 1 part(s)

Date of issue: 10 May 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Primer

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Guiding data for airless spray

Nozzle tip (inch/1000): 15-19
Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time

Substrate temperature 10 °C 23 °C 40 °C

Surface (touch) dry 2h 1h 30 min

Walk-on-dry 14 h 6.5 h 3h
Dry to over coat, minimum 8h 4h 3h
Dried/cured for service 14 d 7d 3d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Induction time 30 min

Pot life 8h

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 140 °C

Immersed, sea water 50 °C 60 °C

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

Date of issue: 10 May 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Primer

Note that the coating will be resistant to various immersion temperatures depending on the specific chemical
and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If
used as part of a system, ensure all coatings in the system have similar heat resistance.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: epoxy, epoxy mastic, zinc epoxy, zinc silicate

Subsequent coat: acrylic, epoxy, polyurethane, polysiloxane

Packaging (typical)
Volume Size of containers
(litres) (litres)

Penguard Primer Comp A 4/16 5/20

Penguard Comp B 1/4 1/5

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Penguard Primer Comp A 24 month(s)
Penguard Comp B 48 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Date of issue: 10 May 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Primer

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 10 May 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
 Technical Data Sheet

Approved 3140;3240;4320 1,2 3140 polyurethane ^(ValidationDate) 1

Hardtop XP

Product description
This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very
good gloss retention. It is a high solids product. The product has good application properties with low dry spray.
To be used as topcoat in atmospheric environments.

Typical use
Marine:
Recommended for topside, deck and superstructure.

Protective:
Recommended for offshore environments, refineries, power plants, bridges and buildings. Suitable for a wide
range of industrial structures. Used as a topcoat in pre-qualified NORSOK systems.
Other

Approvals and certificates

NORSOK System 1, Rev.5
Low flame spread certificate according to IMO/Solas directive
Grain, Newcastle Occupational Health
Food, Compliant with USA, FDA Title 21, Part 175.300 for dry solids
Additional certificates and approvals may be available on request.

Other variants available

Hardtop XP Alu
Hardtop XPL
Hardtop XPF
Refer to separate TDS for each variant.

Colours
according to colour card and Multicolor Industry tinting system (MCI)

Product data
Property Test/Standard Description
Solids by volume ISO 3233 63 ± 2 %
Gloss level (GU 60 °) ISO 2813 gloss (70-85)
Flash point ISO 3679 Method 1 30 °C
Density calculated 1,22 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 336 g/l
VOC-EU IED (2010/75/EU) (calculated) 336 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 336 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Date of issue: 29 March 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XP

Film thickness per coat

Typical recommended specification range

Dry film thickness 50 - 100 μm

Wet film thickness 80 - 160 μm
Theoretical spreading rate 12,6 - 6,3 m²/l

Bright colours may need film thickness in the high end of the recommended specification range to achieve
opacity.

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)

Application
Application methods
The product can be applied by

Spray: Use air spray or airless spray.

Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Roller: May be used. Care must be taken to achieve the specified dry film thickness.

Product mixing ratio (by volume)

Hardtop XP Comp A 10 part(s)

Hardtop XP Comp B 1 part(s)

Date of issue: 29 March 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XP

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 10 / Jotun Thinner No. 26

Jotun Thinner No. 26 is supplied and used in USA due to legislation.

Guiding data for airless spray

Nozzle tip (inch/1000): 13-19

Pressure at nozzle (minimum): 150 bar/2100 psi

Guiding data for air spray

Nozzle tip (inch/1000): 11-19 (HVLP) / 1.1-1.9 mm (pressure pot)
Pressure at nozzle (minimum): 2.1 bar/30 psi (HVLP) / 2.1 bar/30 psi (pressure pot)

Drying and Curing time

Substrate temperature 5 °C 10 °C 23 °C 40 °C

Surface (touch) dry 16 h 6h 3.5 h 2 h

Walk-on-dry 24 h 14 h 7h 4 h
Dry to over coat, minimum 24 h 14 h 7h 4 h
Dried/cured for service 21 d 14 d 7d 3 d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Pot life 1.5 h

Date of issue: 29 March 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XP

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 140 °C

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: epoxy, zinc epoxy, epoxy mastic, polyurethane

Packaging (typical)
Volume Size of containers
(litres) (litres)

Hardtop XP Comp A 4.55 / 18.2 5 / 20

Hardtop XP Comp B 0.45 / 1.8 1/3

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Hardtop XP Comp A 48 month(s)
Hardtop XP Comp B 48 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Date of issue: 29 March 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XP

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 29 March 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
 Technical Data Sheet

Approved 9560;9660;3240 1,2 9560 polyurethane ^(ValidationDate) 1

Hardtop XPF

Product description
This is a two component chemically curing aliphatic acrylic polyurethane coating. It is fast drying. It is a high
solids product. It has a glossy finish with very good gloss retention. To be used as topcoat in atmospheric
environments. It can be applied at sub zero surface temperatures.

Typical use
Marine:
Recommended for topside, deck and superstructure.

Protective:
Recommended for offshore environments, refineries, power plants, bridges and buildings. Suitable for a wide
range of industrial structures. Used as a topcoat in fast drying pre-qualified NORSOK systems.
Other

Approvals and certificates

NORSOK System 1, Rev.5
Low flame spread certificate according to IMO/Solas directive
Grain, Newcastle Occupational Health
Additional certificates and approvals may be available on request.

Colours
according to colour card and Multicolor Industry tinting system (MCI)

Product data
Property Test/Standard Description
Solids by volume ISO 3233 63 ± 2 %
Gloss level (GU 60 °) ISO 2813 gloss (70-85)
Flash point ISO 3679 Method 1 30 °C
Density calculated 1,39 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 336 g/l
VOC-EU IED (2010/75/EU) (calculated) 361 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 324 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Date of issue: 29 March 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XPF

Film thickness per coat

Typical recommended specification range

Dry film thickness 40 - 80 μm

Wet film thickness 65 - 130 μm
Theoretical spreading rate 15,8 - 7,9 m²/l

Bright colours may need film thickness in the high end of the recommended specification range to achieve
opacity.

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)

Application
Application methods
The product can be applied by

Spray: Use air spray or airless spray.

Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Roller: May be used. Care must be taken to achieve the specified dry film thickness.

Product mixing ratio (by volume)

Hardtop XPF Comp A 10 part(s)

Hardtop XP Comp B 1 part(s)

Date of issue: 29 March 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XPF

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 10

Guiding data for airless spray

Nozzle tip (inch/1000): 15-21

Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time

Substrate temperature -10 °C 0 °C 5 °C 10 °C 23 °C

Surface (touch) dry 48 h 10 h 6h 4h 1.5 h

Walk-on-dry 60 h 24 h 16 h 10 h 5h
Dry to over coat, minimum 72 h 24 h 16 h 10 h 5h
Dried/cured for service 60 d 20 d 15 d 10 d 5d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Pot life 1h

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 140 °C

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

Date of issue: 29 March 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XPF

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: epoxy, zinc epoxy, epoxy mastic, polyurethane

Subsequent coat: polyurethane

Packaging (typical)
Volume Size of containers
(litres) (litres)

Hardtop XPF Comp A 4.55 / 18.2 5 / 20

Hardtop XP Comp B 0.45 / 1.8 1/3

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Hardtop XPF Comp A 48 month(s)
Hardtop XP Comp B 48 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation

Date of issue: 29 March 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Hardtop XPF

When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 29 March 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
 Technical Data Sheet

Approved 462;463;9880;464;1500;7021 1,2 462 epoxy ^(ValidationDate) 1

Jota Armour

Product description
This is a three component abrasion resistant polyamine cured epoxy coating. Specially designed as an anti-skid
coating. Suitable on metallic substrates coated with approved primers and on concrete coated with suitable
sealer.

Typical use
Can be used on helidecks, walkways, ramps, weigh bridge decks, decks in general where abrasion resistance
and non-slip properties are required.
Other

Approvals and certificates

Approved to UK Defence Standard 80-134/1 for the Royal Navy, flight decks, hangar decks and weather decks
Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 4, suitable for decks and walkways.
Additional certificates and approvals may be available on request.

Colours
grey 038, green 137, BS 640

Product data
Property Test/Standard Description
STANDARD GRADE
Solids by volume ISO 3233 90 ± 2 %
Gloss level (GU 60 °) ISO 2813 semi gloss (35-70)
Flash point ISO 3679 Method 1 35 °C
Density calculated 1,43 kg/l
VOC-EU IED (2010/75/EU) (calculated) 123 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 158 g/l

WINTER GRADE
Solids by volume ISO 3233 84 ± 2 %
Flash point ISO 3679 Method 1 31 °C
VOC-EU IED (2010/75/EU) (calculated) 144 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 143 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
Gloss description: According to Jotun Performance Coatings' definition.

Date of issue: 28 April 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Jota Armour

Film thickness per coat

Typical recommended specification range
STANDARD GRADE

Dry film thickness 750 - 3000 μm

Wet film thickness 830 - 3330 μm
Theoretical spreading rate 1,2 - 0,3 m²/l

WINTER GRADE
Dry film thickness 750 - 3000 μm
Wet film thickness 890 - 3570 μm
Theoretical spreading rate 1,1 - 0,3 m²/l

Anti-slip roughness profile of coating limits accuracy on film thickness measurements. Approximate spreading
rate for 1000 μm dry film is 8 m²/kit from practical testing.

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)

Application
Application methods
The product can be applied by

Spray: Gravity Feed Hopper Gun or other suitable equipment. Consult Jotun for additional
information, as required.

Product mixing ratio (by weight)

Mix Comp A and Comp B, then add Comp C (graded aggregate), 10 minutes prior to use.

Date of issue: 28 April 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Jota Armour

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Drying and Curing time

Substrate temperature 0 °C 5 °C 10 °C 23 °C 40 °C

STANDARD GRADE
Surface (touch) dry 8h 5h 3 h
Walk-on-dry 24 h 14 h 6 h
Dry to over coat, minimum 28 h 14 h 6 h
Dried/cured for service 14 d 7d 2 d

WINTER GRADE
Surface (touch) dry 22 h 14 h 8h 3h
Walk-on-dry 32 h 24 h 24 h 8h
Dry to over coat, minimum 32 h 24 h 24 h 8h
Dried/cured for service 28 d 14 d 14 d 4d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

STANDARD GRADE
Induction time 10 min
Pot life 2h

WINTER GRADE
Pot life 1h

Date of issue: 28 April 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Jota Armour

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 120 °C

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: epoxy, epoxy mastic, zinc epoxy

Subsequent coat: epoxy, epoxy mastic, polyurethane

Packaging (typical)
Jota Armour Comp A 4l
Jota Armour Std Comp B 0.7 l
Jota Armour Wintergrade Comp B 1l
Jota Armour Comp C 4.3 l / 14 kg

The components may be packed as a kit in a 20 l mixing pail.

9 l kit: 4 l Comp A, 0.7 l Jota Armour Std Comp B and 4.3 l / 14 kg Comp C.
9.3 l kit: 4 l Comp A, 1 l Jota Armour Wintergrade Comp B and 4.3 l / 14 kg Comp C.

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Jota Armour Comp A 48 month(s)
Jota Armour Std Comp B 48 month(s)
Jota Armour Wintergrade Comp B 48 month(s)
Jota Armour Comp C 120 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Date of issue: 28 April 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Jota Armour

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 28 April 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]