Packet Tracer - Configure VTP and DTP

Addressing Table

Device Interface IP Address Subnet Mask

PC0 NIC 192.168.10.1 255.255.255.0

PC1 NIC 192.168.20.1 255.255.255.0
PC2 NIC 192.168.30.1 255.255.255.0
PC3 NIC 192.168.30.2 255.255.255.0
PC4 NIC 192.168.20.2 255.255.255.0
PC5 NIC 192.168.10.2 255.255.255.0
S1 VLAN 99 192.168.99.1 255.255.255.0
S2 VLAN 99 192.168.99.2 255.255.255.0
S3 VLAN 99 192.168.99.3 255.255.255.0

Objectives
Part 1: Configure and Verify DTP
Part 2: Configure and Verify VTP

Background / Scenario
As the number of switches in a network increases, the administration necessary to manage the VLANs and
trunks can be challenging. To ease some of the VLAN and trunking configurations, VLAN trunking protocol
(VTP) allows a network administration to automate the management of VLANs. Trunk negotiation between
network devices is managed by the Dynamic Trunking Protocol (DTP), and is automatically enabled on
Catalyst 2960 and Catalyst 3560 switches.
In this activity, you will configure trunk links between the switches. You will configure a VTP server and VTP
clients in the same VTP domain. You will also observe the VTP behavior when a switch is in VTP transparent
mode. You will assign ports to VLANs and verify end-to-end connectivity with the same VLAN.

Instructions
Part 1: Configure and Verify DTP
In Part 1, you will configure trunk links among the switches, and you will configure VLAN 999 as the native
VLAN.

Step 1: Verify VLAN configuration.

Verify the configured VLANs on the switches.
a. On S1, click the CLI tab. At the prompt, enter enable and enter the show vlan brief command to verify
the configured VLANs on S1.
b. Repeat step a. on S2 and S3.
Question:

What VLANs are configured on the switches?

 2017 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 5 www.netacad.com
Packet Tracer - Configure VTP and DTP

Type your answers here.

Step 2: Configure Trunks on S1, S2, and S3.

Dynamic trunking protocol (DTP) manages the trunk links between Cisco switches. Currently all the
switchports are in the default trunking mode, which is dynamic auto. In this step, you will change the trunking
mode to dynamic desirable for the link between switches S1 and S2. For the link between switches S1 and
S3, the link will be set as a static trunk. Use VLAN 999 as the native VLAN in this topology.
a. On switch S1 and switch S2, configure the trunk link to dynamic desirable on the GigabitEthernet 0/1
interface. The configuration of S1 is shown below.
S1(config)# interface g0/1
S1(config-if)# switchport mode dynamic desirable
b. For the trunk link between S1 and S3, configure a static trunk link on the GigabitEthernet 0/2 interface.
S1(config)# interface g0/2
S1(config-if)# switchport mode trunk
S3(config)# interface g0/2
S3(config-if)# switchport mode trunk
c. Verify trunking is enabled on all the switches using the show interfaces trunk command.
Question:

What is the native VLAN for these trunks currently?

Type your answers here.

d. Configure VLAN 999 as the native VLAN for the trunk links on S1.
S1(config)# interface range g0/1 - 2
S1(config-if-range)# switchport trunk native vlan 999
Question:

What messages did you receive on S1? How would you correct it?
Type your answers here.

e. On S2 and S3, configure VLAN 999 as the native VLAN.

f. Verify trunking is successfully configured on all the switches. You should be able ping one switch from
another switch in the topology using the IP addresses configured on the SVI.

Part 2: Configure and Verify VTP

S1 will be configured as the VTP server and S2 will be configured as a VTP client. All the switches will be
configured to be in the VTP domain CCNA and use the VTP password cisco.
VLANs can be created on the VTP server and distributed to other switches in the VTP domain. In this part,
you will create 3 new VLANs on the VTP server, S1. These VLANs will be distributed to S2 using VTP.
Observe how the transparent VTP mode behaves.

Step 1: Configure S1 as VTP server.

Configure S1 as the VTP server in the CCNA domain with the password cisco.
a. Configure S1 as a VTP server.
S1(config)# vtp mode server
Setting device to VTP SERVER mode.
b. Configure CCNA as the VTP domain name.

 2017 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 5 www.netacad.com
Packet Tracer - Configure VTP and DTP

S1(config)# vtp domain CCNA

Changing VTP domain name from NULL to CCNA
c. Configure cisco as the VTP password.
S1(config)# vtp password cisco
Setting device VLAN database password to cisco

Step 2: Verify VTP on S1.

a. Use the show vtp status command on the switches to confirm that the VTP mode and domain are
configured correctly.
b. To verify the VTP password, use the show vtp password command.

Step 3: Add S2 and S3 to the VTP domain.

Before S2 and S3 will accept VTP advertisements from S1, they must belong to the same VTP domain.
Configure S2 as a VTP client with CCNA as the VTP domain name and cisco as the VTP password.
Remember that VTP domain names are case sensitive.
a. Configure S2 as a VTP client in the CCNA VTP domain with the VTP password cisco.
S2(config)# vtp mode client
Setting device to VTP CLIENT mode.
S2(config)# vtp domain CCNA
Changing VTP domain name from NULL to CCNA
S2(config)# vtp password cisco
Setting device VLAN database password to cisco
b. To verify the VTP password, use the show vtp password command.
S2# show vtp password
VTP Password: cisco
c. Configure S3 to be in the CCNA VTP domain with the VTP password cisco. Switch S3 will be set in VTP
transparent mode.
S3(config)# vtp mode transparent
S3(config)# vtp domain CCNA
Changing VTP domain name from NULL to CCNA
S3(config)# vtp password cisco
Setting device VLAN database password to cisco
d. Enter show vtp status command on all the switches to answer the following question.
Question:

Notice that the configuration revision number is 0 on all three switches. Explain.
Type your answers here.

Step 4: Create more VLANs on S1.

a. On S1, create VLAN 10 and name it Red.
S1(config)# vlan 10
S1(config-vlan)# name Red
b. Create VLANs 20 and 30 according to the table below.

 2017 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 5 www.netacad.com
Packet Tracer - Configure VTP and DTP

VLAN Number VLAN Name

10 Red
20 Blue
30 Yellow

c. Verify the addition of the new VLANs. Enter show vlan brief at the privileged EXEC mode.
Question:

Which VLANs are configured on S1?

Type your answers here.

d. Confirm configuration changes using the show vtp status command on S1 and S2 to confirm that the
VTP mode and domain are configured correctly. Output for S2 is shown here:
Question:

How many VLANs are configured on S2? Does S2 have the same VLANs as S1? Explain.
Type your answers here.

Step 5: Observe VTP transparent mode.

S3 is currently configured as VTP transparent mode.
a. Use show vtp status command to answer the following question.
Questions:

How many VLANs are configured on S3 currently? What is the configuration revision number? Explain
your answer.
Type your answers here.

How would you change the number of VLANs on S3?

Type your answers here.

b. Change VTP mode to client on S3.

Question:

Use show commands to verify the changes on VTP mode. How many VLANs exists on S3 now?
Type your answers here.

Note: VTP advertisements are flooded throughout the management domain every five minutes, or
whenever a change occurs in VLAN configurations. To accelerate this process, you can switch between
Realtime mode and Simulation mode until the next round of updates. However, you may have to do this
multiple times because this will only forward Packet Tracer’s clock by 10 seconds each time. Alternatively,
you can change one of the client switches to transparent mode and then back to client mode.

Step 6: Assign VLANs to Ports

Use the switchport mode access command to set access mode for the access links. Use the switchport
access vlan vlan-id command to assign a VLAN to an access port.

Ports Assignments Network

S2 F0/1 - 8
S3 F0/1 - 8 VLAN 10 (Red) 192.168.10.0 /24
S2 F0/9 - 16 VLAN 20 (Blue) 192.168.20.0 /24

 2017 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 5 www.netacad.com
Packet Tracer - Configure VTP and DTP

Ports Assignments Network

S3 F0/9 - 16
S2 F0/17 - 24
S3 F0/17 - 24 VLAN 30 (Yellow) 192.168.30.0 /24

a. Assign VLANs to ports on S2 using assignments from the table above.

S2(config-if)# interface range f0/1 - 8
S2(config-if-range)# switchport mode access
S2(config-if-range)# switchport access vlan 10
S2(config-if-range)# interface range f0/9 -16
S2(config-if-range)# switchport mode access
S2(config-if-range)# switchport access vlan 20
S2(config-if-range)# interface range f0/17 - 24
S2(config-if-range)# switchport mode access
S2(config-if-range)# switchport access vlan 30
b. Assign VLANs to ports on S3 using assignment from the table above.

Step 7: Verify end to end connectivity.

a. From PC0 ping PC5.
b. From PC1 ping PC4.
c. From PC2 ping PC3.
End of document

 2017 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 5 www.netacad.com