Scribd
Upload
711 views

Data Sheet Level Alarm Switches S85 PDF

The S85 is a coolant level switch with a programmable microprocessor that can provide one or two output signals if fluid falls below or rises above a preset level, with a delay to avoid false alarms. It has a small footprint for minimal tank intrusion and damage risk. It is suitable for many applications and offers customization options. It has proven reliable over 10 years with over 500,000 units supplied. Future variants will offer dual outputs and an all-stainless steel housing.

Uploaded by

faraidun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
711 views

Data Sheet Level Alarm Switches S85 PDF

The S85 is a coolant level switch with a programmable microprocessor that can provide one or two output signals if fluid falls below or rises above a preset level, with a delay to avoid false alarms. It has a small footprint for minimal tank intrusion and damage risk. It is suitable for many applications and offers customization options. It has proven reliable over 10 years with over 500,000 units supplied. Future variants will offer dual outputs and an all-stainless steel housing.

Uploaded by

faraidun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

S85 capacitance

coolant level switch

Technical Data – S85 coolant alarm switch

Description
The Model S85 is an active device which is designed to give an alarm signal
if fluid falls below or rises above a preset level. It will only signal after a few
seconds delay in sensing the level to eliminate false alarms due to turbulence.

Containing a programmable microprocessor, the switch can offer one or two


output pins which can sink to ground or supply a source voltage, or both.

Its tiny footprint with limited intrusion into the tank means a reduced risk of
damage and a wide range of options and customisations makes it suitable for
most applications.

SPECIFICATION
Electrical Rating: Construction:
Supply Voltage: 5 VDC or 7 - 35 VDC Body: Brass
Supply Current: 1.5mA + source output Probe: PTFE
Max. Load Current: 1.0A (sink) or 20mA (source) Terminals: SAE CA210Brass, Tin Plated
Alarm Delay Time: 0 - 25 secs rising or falling (factory set) Seals: NBR rubber
Connection: 4 way Delphi Packard connector Connector: 30% Glass Filled Nylon 6
Start up Delay: 1 - 5 secs Thread sealant: Vibra-Seal 516

Fluid Types: Connections:


Water based fluids compatible with Brass, PTFE See diagram below
and NBR rubber. Note: Outputs are factory selectable and dual outputs on
output 1 are available on request.

Environmental Ratings
Sealing: IP67
Max. pressure: 5.0 Bar (72 psi)
Temp. ranges: Fluid: -40°C to +130°C
Storage: -40°C to +140°C
Weight: 53g
S85 capacitance
coolant level switch

Technical Data – S85 coolant alarm switch

Product background
The S85 series was introduced to the market over 10 years ago and since its inception over half a million sensors have
been supplied proving it as a very robust and reliable product. It has now become an industry standard and is specified
worldwide by many leading engine manufacturers including Perkins, Cummins and Caterpillar.

Test performance data


EMC: Type approval to EN ISO 13766:2006 for Narrowband Emissions, Broadband Emissions, Radiated Immunity,
Transient Pulses & Electrostatic discharge.

Compliance to various customer specified Salt spray/fog tests.

Vibration (15.3 grms): Testing performed in accordance with BSEN 60068-2-64:1993.


3 orthogonal planes for 3 hours per plane.

Frequency (Hz) G2/Hz


24 0.4
60 0.5
100 0.5
240 0.1
2000 0.1

Reliability Performance:
The current PPM figure is under 50PPM for warranty returns received from 2008 - 2010.

Optional accessories:
Mating connector kits to suit harness wire cross sectional area of 0.8 to 1.0mm2 and sleeve 1.60 to 2.15mm:
Our Part no Description
C/K1 From the Packard Metri-Pack 150 series of connectors
C/K2 From the DIN 72 585 series of connectors

Special connectors such as MIL spec. or flying leads with customer’s own connectors are available on request.

Reduced probe length versions are available subject to Fozmula Engineering Department approval.

Future Developments:
Available from late 2010 an S 85 variant will be available in a dual output format to switch at:-
1.2 VDC in coolant.
4 VDC in Air.

It is planned to introduce an S85 variant in all 316 stainless steel

GTS Gauges Transmitters Switches Pty Ltd


6 Dayana Close Midvale WA 6056
Available From: Ph: 08 9250 4400 Fax: 08 9250 4500
[email protected] www.gtsgauges.com.au

You might also like