HXC-F Counting Scale

Operation Manual

V1.0-2013
 I. Precautions Before Using The Scale
Environment
TABLE OF CONTENTS
The scale should always be used in an environment, which is free

I. Precautions Before Using The Scale---------------------1 from excessive air currents, corrosives, vibration, and temperature or
humidity extremes. These factors will affect displayed weight
II. Explanation Of Display Symbols-------------------------2
reading.
III. Keypad Functions----------------------------------------2
DO NOT install the scale :
IV. Operations------------------------------------------------4 z Next to open windows or doors causing drafts or rapid

( I ) SWITCH ON & OFF---------------------------------------4 temperature changes.

z Near air conditioning or heating vents.
(II) ZERO FUNCTION-----------------------------------------4
z Near vibrating, rotating or reciprocating equipment.
(III) TARE FUNCTION-----------------------------------------4
z Near magnetic fields or equipment that generates
(IV) COUNTING---------------------------------------------5 magnetic fields.

(V) ACCUMULATION----------------------------------------5 z On an unstable work surface.

z In a dusty environment.
(VI) WARNING FUNCTION-----------------------------------6
z In direct sunlight.
(VII) WEIGHT RESPONSE SPEED-------------------------------6
Leveling the Scale
(VIII) BACKLIGHT--------------------------------------------6 The scale is equipped with a level indicator on the left bottom side of
V. Calibration------------------------------------------------7 the front panel and four adjustable leveling feet. Adjust the
leveling feet until the bubble appears in the center circle of the
VI. Recharging the battery----------------------------------7
indicator.

Turn on Scale
Do not turn on scale with anything on the platform. The
switch is located on the right side of the scale. The scale will return to
zero for normal weighing. The scale is then ready for use. Give a
warm-up for 15~30 minutes before use is most suggested.

1
II. Explanation Of Display Symbols
: Use this key to accumulate weight value.
: Scale is in TARE mode.
: Press this key to clear the accumulated value.
: Scale is in stable mode.
: This key is for quantity warning function.
: Scale is in ZERO mode.

: Press this key to cancel warning function.

: Scale is in ACCUMULATION mode.

: This is for calibration.

: Samples are insufficient
: Use this key to choose preset desired weight measuring unit

: Scale is in WARNING mode.

: use this key to confirm the given unit weight of the sample.
: Scale needs recharging once this battery sign
appears. : Sampling key . Used for keying in a sample size.

: When input the incorrect number,press this key to clear.

III. Keypad Functions

: Press this key to turn on/off backlight.
～ : Numeric keys.
: Weight response speed.
: Decimal point key.

: If there is a minor weight displayed, without anything

on the pan; hit the zero key to clear the display.

: Use this key to subtract the container’s weight.

Indicates that the current weight reading is net weight.

3
2
IV. Operations (IV) COUNTING

(I) SWITCH ON & OFF 1.Unit weight setting

Push the ON/OFF switch to “ I “ position to turn on the scale & to A known unit weight can be directly input by giving the

“ O ” position to turn off the scale.

value through numeric keys first then followed by pressing
keys.
(II) ZERO FUNCTION
2.Unit weight by sampling
Zero range : + 2% of max. capacity
a. Put the objects intended for sampling on the pan.
b. Key in the quantity (pcs) of the objects,this number will blink in unit
Press key to return the display to zero in case there is
any zero drifting while unloaded. Weight display.

c. Press key,the calculated unit weight will then be shown in

(III) TARE FUNCTION
UNIT WEIGHT display and the remaining objects, the total quantity
will then be shown in TOTAL COUNTS display
1. Press key to subtract the container’s weight and then the
indicator “◀”will be shown at the right side of symbol. ※ Sample size not enough

At this moment, place objects in the container. The display will If the quantity of item put on the pan for sampling (sample size) is

show the net weight value. Remove both the container and
not enough, the indicator“◀”will be shown at the left side of to
objects, the display will show the gross weight (container + objects )
remind user to add more for sampling for getting accurate
accompanied by a negative sign.
quantity calculation.
2. If the container’s weight is known before, it is allowed to input the

(V) ACCUMULATION
value and press to subtract the container’s weight, and then
place objects with container on the pan. 1.Accumulate weight value

The display will show the net weight value.

a.Place objects on the pan, and press to accumulate.
※ (container + objects ) ≤ Max Capacity.
The total weight will be shown on the WEIGHT display.
b.And the UNIT WEIGHT display will show "Addxx" (0<xx<99)
Press again to eliminate Tare mode.

4
5
 2.Accumulate quantity V.Calibration
a.Under counting mode, press to accumulate quantity.
b.The WEIGHT display will show total weight value, UNIT WEIGHT Switch on the scale and press for about 4 seconds.

display will show "Addxx" (0<xx<99), TOTAL COUNTS display will show
Press to bring the display to zero in case there is any zero
total quantity.
drifting while unloaded.
※ The value or quantity shown on the display will disappear in about 3
1. Single point calibration
seconds.
Place weights on the pan and input the weight value.
Press to clear accumulated value or quantity.
Calibration would be finished automatically when it is stable.
2. three points calibration
(VI) WARNING FUNCTION
1.Input quantity that needs warning while exceeding,and press . a.Press key.
2.The indicator“◀”will be shown at the left side of on screen. b.The TOTAL COUNTS will show the weight value (P1) that needs for
3.Under counting mode, if the quantity above preset value. calibration
Scale will beep. c.Place equivalent weights and wait for next step.
(For example, you input 100. When the quantity is more than 100pcs, d.When it shows P2, P3 value, repeat step b and c.
scale beeps )
4.Press to eliminate warning mode.

VI. Recharging the battery

(VII) WEIGHT RESPONSE SPEED Turn off the scale before recharging. A LED indicator on the panel,
next to the word “ In Charge “, will go RED in the process of charging
Press to choose response speed (speed1-speed3).
the battery. It will take approx. 8 hours to fully recharge the battery.

(VIII) BACKLIGHT

Press to turn on/off backlight.

6 7