(https://theconstructor.

org/)

N o n - D e s t r u c t i v e Te s t i n g o f C o n c r e t e a n d i t s M e t h o d s

Non-destructive testing of concrete is a method to obtain the compressive strength and other properties of
concrete from the existing structures. This test provides immediate results and actual strength and properties of
concrete structure.

The standard method of evaluating the quality of concrete in buildings or structures is to test specimens cast
simultaneously for compressive, flexural and tensile strengths.

The main disadvantages are that results are not obtained immediately; that concrete in specimens may differ from
that in the actual structure as a result of different curing and compaction conditions; and that strength properties
of a concrete specimen depend on its size and shape.

Although there can be no direct measurement of the strength properties of structural concrete for the simple
reason that strength determination involves destructive stresses, several non- destructive methods of assessment
have been developed.

These depend on the fact that certain physical properties of concrete can be related to strength and can be
measured by non-destructive methods. Such properties include hardness, resistance to penetration by projectiles,
rebound capacity and ability to transmit ultrasonic pulses and X- and Y-rays.

These non-destructive methods may be categorized as penetration tests, rebound tests, pull-out techniques,
dynamic tests, radioactive tests, maturity concept. It is the purpose of this Digest to describe these methods
briefly, outlining their advantages and disadvantages.

Methods of Non-Destruccttive Testing of Concretee

Following are different methods of NDT on concrete:

1. Penetration method

2. Rebound hammer method

3. Pull out test method

4. Ultrasonic pulse velocity method

5. Radioactive methods

PPeenneettrraattiioonn TTeessttss oonn C

Coonnccrreettee ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee//ppeenneettrraattiioonn--rreessiissttaannccee--w
wiinnddssoorr--pprroobbee--
ppnnrr--tteesstt//22885533//))
The Windsor probe is generally considered to be the best means of testing penetration. Equipment consists of a
powder-actuated gun or driver, hardened alloy probes, loaded cartridges, a depth gauge for measuring
penetration of probes and other related equipment.

A probe, diameter 0.25 in. (6.5 mm) and length 3.125 in. (8.0 cm), is driven into the concrete by means of a
precision powder charge. Depth of penetration provides an indication of the compressive strength of the concrete.

Although calibration charts are provided by the manufacturer, the instrument should be calibrated for type of
concrete and type and size of aggregate used.

LLiim
miittaattiioonnss aanndd A
Addvvaannttaaggeess

The probe test produces quite variable results and should not be expected to give accurate values of concrete
strength. It has, however, the potential for providing a quick means of checking quality and maturity of in situ
concrete.

It also provides a means of assessing strength development with curing. The test is essentially non-destructive,
since concrete and structural members can be tested in situ, with only minor patching of holes on exposed faces.

R
Reebboouunndd H
Haam
mmmeerr M
Meetthhoodd ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee//rreebboouunndd--hhaam
mmmeerr--tteesstt//22883377//))

The rebound hammer is a surface hardness tester for which an empirical correlation has been established between
strength and rebound number.

The only known instrument to make use of the rebound principle for concrete testing is the Schmidt hammer,
which weighs about 4 lb (1.8 kg) and is suitable for both laboratory and field work. It consists of a spring-
controlled hammer mass that slides on a plunger within a tubular housing.

The hammer is forced against the surface of the concrete by the spring and the distance of rebound is measured
on a scale. The test surface can be horizontal, vertical or at any angle but the instrument must be calibrated in
this position.

Calibration can be done with cylinders (6 by 12 in., 15 by 30 cm) of the same cement and aggregate as will be
used on the job. The cylinders are capped and firmly held in a compression machine.

Several readings are taken, well distributed and reproducible, the average representing the rebound number for
the cylinder. This procedure is repeated with several cylinders, after which compressive strengths are obtained.

LLiim
miittaattiioonnss aanndd A
Addvvaannttaaggeess

The Schmidt hammer provides an inexpensive, simple and quick method of obtaining an indication of concrete
strength, but accuracy of ±15 to ±20 per cent is possible only for specimens cast cured and tested under
conditions for which calibration curves have been established.

The results are affected by factors such as smoothness of surface, size and shape of specimen, moisture condition
of the concrete, type of cement and coarse aggregate, and extent of carbonation of surface.

PPuullll--O
Ouutt TTeessttss oonn C
Coonnccrreettee ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee//ppuulllloouutt--llookk--tteesstt--oonn--hhaarrddeenneedd--ccoonnccrreettee
//22886611//))

A pull-out test measures, with a special ram, the force required to pull from the concrete a specially shaped steel
rod whose enlarged end has been cast into the concrete to a depth of 3 in. (7.6 cm).

The concrete is simultaneously in tension and in shear, but the force required to pull the concrete out can be
related to its compressive strength.

The pull-out technique can thus measure quantitatively the in-situ strength of concrete when proper correlations
have been made. It has been found, over a wide range of strengths, that pull-out strengths have a coefficient of
variation comparable to that of compressive strength.

LLiim
miittaattiioonnss aanndd A
Addvvaannttaaggeess
Although pullout tests do not measure the interior strength of mass concrete, they do give information on the
maturity and development of strength of a representative part of it. Such tests have the advantage of measuring
quantitatively the strength of concrete in place.

Their main disadvantage is that they have to be planned in advance and pull-out assemblies set into the formwork
before the concrete is placed. The pull-out, of course, creates some minor damage.

The test can be non-destructive, however, if a minimum pullout force is applied that stops short of failure but
makes certain that a minimum strength has been reached. This is information of distinct value in determining
when forms can be removed safely.

DDyynnaam miicc N Noonn D Deessttrruuccttiivvee TTeessttss oonn C

Coonnccrreettee ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee//uullttrraassoonniicc--ppuullssee--vveelloocciittyy--
uuppvv--tteesstt//22884477//))

At present the uullttrraassoonniicc ppuullssee vveelloocciittyy m

meetthhoodd (https://theconstructor.org/concrete/ultrasonic-pulse-velocity-
upv-test/2847/) is the only one of this type that shows potential for testing concrete strength in situ. It measures
the time of travel of an ultrasonic pulse passing through the concrete.

The fundamental design features of all commercially available units are very similar, consisting of a pulse
generator and a pulse receiver.

Pulses are generated by shock-exciting piezo-electric crystals, with similar crystals used in the receiver. The time
taken for the pulse to pass through the concrete is measured by electronic measuring circuits.

Pulse velocity tests can be carried out on both laboratory-sized specimens and completed concrete structures, but
some factors affect measurement:

1. There must be smooth contact with the surface under test; a coupling medium such as a thin film of oil is
mandatory.

2. It is desirable for path-lengths to be at least 12 in. (30 cm) in order to avoid any errors introduced by
heterogeneity.

3. It must be recognized that there is an increase in pulse velocity at below-freezing temperature owing to
freezing of water; from 5 to 30°C (41 – 86°F) pulse velocities are not temperature dependent.

4. The presence of reinforcing steel in concrete has an appreciable effect on pulse velocity. It is therefore
desirable and often mandatory to choose pulse paths that avoid the influence of reinforcing steel or to make
corrections if steel is in the pulse path.

A
Apppplliiccaattiioonnss aanndd LLiim
miittaattiioonnss

The ppuullssee vveelloocciittyy m

meetthhoodd (https://theconstructor.org/concrete/ultrasonic-pulse-velocity-upv-test/2847/) is an
ideal tool for establishing whether concrete is uniform. It can be used on both existing structures and those under
construction.

Usually, if large differences in pulse velocity are found within a structure for no apparent reason, there is strong
reason to presume that defective or deteriorated concrete is present.

High pulse velocity readings are generally indicative of good quality concrete. A general relation between concrete
quality and pulse velocity is given in Table.

TTaabbllee:: Q
Quuaalliittyy ooff C
Coonnccrreettee aanndd PPuullssee V
Veelloocciittyy

G
Geenneerraall C
Coonnddiittiioonnss P
Puullssee V
Veelloocciittyy fftt//sseecc

E
Exxcceelllleenntt Above 15,000

G
Goooodd 12,000-15,000

Q
Quueessttiioonnaabbllee 10,000-12,000

P
Poooorr 7,000-10,000
 V
Veerryy P
Poooorr below 7,000

Fairly good correlation can be obtained between cube compressive strength and pulse velocity. These relations
enable the strength of structural concrete to be predicted within ±20 per cent, provided the types of aggregate
and mix proportions are constant.

The pulse velocity method has been used to study the effects on concrete of freeze-thaw action, sulphate attack,
and acidic waters. Generally, the degree of damage is related to a reduction in pulse velocity. Cracks can also be
detected.

Great care should be exercised, however, in using pulse velocity measurements for these purposes since it is often
difficult to interpret results. Sometimes the pulse does not travel through the damaged portion of the concrete.

The pulse velocity method can also be used to estimate the rate of hardening and strength development of
concrete in the early stages to determine when to remove formwork. Holes have to be cut in the formwork so that
transducers can be in direct contact with the concrete surface.

As concrete ages, the rate of increase of pulse velocity slows down much more rapidly than the rate of
development of strength, so that beyond a strength of 2,000 to 3,000 psi (13.6 to 20.4 MPa) accuracy in
determining strength is less than ±20%.

Accuracy depends on careful calibration and use of the same concrete mix proportions and aggregate in the test
samples used for calibration as in the structure.

In summary, ultrasonic pulse velocity tests have a great potential for concrete control, particularly for establishing
uniformity and detecting cracks or defects. Its use for predicting strength is much more limited, owing to the large
number of variables affecting the relation between strength and pulse velocity.

R
Raaddiiooaaccttiivvee M
Meetthhooddss ooff N
NDDTT oonn C
Coonnccrreettee

Radioactive methods of testing concrete can be used to detect the location of reinforcement, measure density and
perhaps establish whether honeycombing has occurred in structural concrete units. Gamma radiography is
increasingly accepted in England and Europe.

The equipment is quite simple and running costs are small, although the initial price can be high. Concrete up to
18 in. (45 cm) thick can be examined without difficulty.

Purpose of Non-Des truccttive Tests on Concrete

A variety of Non Destructive Testing (NDT) methods have been developed or are under development for
investigating and evaluating concrete structures.

These methods are aimed at estimation of strength and other properties; monitoring and assessing
corrosion; measuring crack size and cover; assessing grout quality; detecting defects and identifying
relatively more vulnerable areas in concrete structures.

Many of NDT methods used for concrete testing have their origin to the testing of more homogeneous,
metallic system. These methods have a sound scientific basis, but heterogeneity of concrete makes
interpretation of results somewhat difficult.

There could be many parameters such as materials, mix, workmanship and environment, which influence
the results of measurements.

Moreover, these test s measure some other property of concrete (e.g. hardness) and the results are
interpreted to assess a different property of concrete e.g. strength, which is of primary interest.

Thus, interpretation of results is very important and difficult job where generalization is not possible. As such,
operators can carry out tests but interpretation of results must be left to experts having experience and
knowledge of application of such non-destructive tests.
P
Puurrppoosseess ooff N
Noonn--ddeessttrruuccttiivvee TTeessttss aarree::

1. Estimating the in-situ compressive strength

2. Estimating the uniformity and homogeneity

3. Estimating the quality in relation to standard requirement

4. Identifying areas of lower integrity in comparison to other parts

5. Detection of presence of cracks, voids and other imperfections

6. Monitoring changes in the structure of the concrete which may occur with time

7. Identification of reinforcement profile and measurement of cover, bar diameter, etc.

8. Condition of prestressing/reinforcement steel with respect to corrosion

9. Chloride, sulphate, alkali contents or degree of carbonation

10. Measurement of Elastic Modulus

11. Condition of grouting in prestressing cable ducts

Types of Non Destructivvee Equipments

According to their use, non-destructive equipment can be grouped as under:

1. Strength estimation of concrete

2. Corrosion assessment and monitoring

3. Detecting defects in concrete structure

4. Laboratory tests

R
Reeaadd M
Moorree::

N
Noonn D
Deessttrruuccttiivvee TTeessttss ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccaatteeggoorryy//pprraaccttiiccaall--gguuiiddee//nnddtt//))

TTeessttss oonn H
Haarrddeenneedd C
Coonnccrreettee ffoorr Q
Quuaalliittyy C
Chheecckk ooff C
Coonnssttrruuccttiioonn ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee//tteessttss--
oonn--hhaarrddeenneedd--ccoonnccrreettee//1
199112
2//))

W
Whhaatt iiss U
Ullttrraassoonniicc TTeessttiinngg ooff C
Coonnccrreettee ffoorr C
Coom
mpprreessssiivvee S
Sttrreennggtthh?? ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee
//uullttrraassoonniicc--tteesstt--oonn--ccoonnccrreettee//2
2884
477//))

C
Coom
mpprreessssiivvee S
Sttrreennggtthh ooff C
Coonnccrreettee --C
Cuubbee TTeesstt,, PPrroocceedduurree,, R
Reessuullttss ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee
//ccoom
mpprreessssiivvee--ssttrreennggtthh--ccoonnccrreettee--ccuubbee--tteesstt//1
1556
611//))

TTeessttiinngg ooff C
Coonnccrreettee C
Coorreess ffoorr S
Sttrreennggtthh –
–SSaam
mpplliinngg aanndd PPrroocceedduurree ((hhttttppss::////tthheeccoonnssttrruuccttoorr..oorrgg//ccoonnccrreettee
//tteessttiinngg--ooff--ccoonnccrreettee--ccoorreess//5
5773
333//))

©
©22001177 TThhee C
Coonnssttrruuccttoorr