AIRPEL

F I L T R A T I O N
 INTRODUCTION
Airpel Filtration Ltd is a leading manufacturer and supplier of
filters to the UK and overseas markets. The Airpel headquarters
and manufacturing facility is located at Chalfont St. Peter,
Buckinghamshire, England, some 30 miles west of London and
is readily accessible by road, rail or air.

Founded in 1939, the company was acquired in 1987 by EIS

Group plc and now forms part of the EIS Vacuum and Filtration
Division.

With the backing and support of this major international

engineering group, Airpel is ideally placed to continue its
programme of product design and development. The company
maintains close contact with the changing needs of the market
through a UK based direct sales force through an established
world-wide network of agents and distributors.

The manufacturing facility uses the latest CNC machinery in the

production of the Airpel range of quality filters. Airpel is
continually updating the production machinery and processes
to ensure its manufacturing methods reflect the latest modern
production practices.

Airpel is committed to a policy of total Quality Assurance and

has been accredited with ISO 9001 since 1987. With over 50
years experience in the design and manufacture of liquid filters
Airpel operates from a position of knowledge and authority
within the filtration industry and is happy to work with other
companies in partnerships dedicated to solving their filtration
problem.

Care has been taken to ensure that the information in this

catalogue is accurate but the illustrations and brief descriptions
provide an approximate guide only. To the best of our
knowledge the data contained herein is accurate at the time of
publication. Airpel Filtration Ltd assume no responsibility for
typographical errors or omissions or for any misinterpretation of
the information provided in this catalogue. All designs are
subject to alteration without notice.

CERT No. F1286

QAU 3289/87

BS EN
IS0 9001
1994
AIRPEL
F I L T R A T I O N

2
 AIRPEL FILTERS AND STRAINERS
PRODUCT SELECTION:
BASKET STRAINERS
Type Materials of Construction* Size Range Page No.
Single Strainer Cast iron, cast steel, bronze 20mm - 250mm* 4
and stainless steel (3/4 - 10 )
// //

Dual Strainer Cast iron, cast steel, bronze 20mm - 200mm* 8

(for uninterrupted and stainless steel (3/4 - 8 )
// //

flow when cleaning

baskets)

Sizing Data, Accessories and Spares Identification 10

SELF CLEAN FILTERS

Type Materials of Construction* Size Range Page No.
Standard Pressure Cast iron, cast steel and stainless steel 20mm - 300mm* 15
High Pressure (3/4 - 12 )
// //

Vertical Exit
(for uninterrupted
flow, and cleaning
with no operator
contact)
Sizing Data and Spares Identification 22

Y-TYPE STRAINERS
Materials of Construction* Size Range Page No.
Cast steel and stainless steel 20mm - 200mm* 24
(3/4 - 10 )
// //

TEMPORARY STRAINERS
Materials of Construction* Size Range Page No.
Stainless steel 20mm - 200mm* 26
(3/4 - 10 )
// //

Guide to Filter Compatibility 27

Filter Application Details 30
*Please note that other materials and sizes of filters/strainers are available upon request.

3
 AIRPEL SINGLE FILTERS Model OV
Sizes 20mm ( / ”) - 150mm (6”)
3 4

Airpel Single Filters have for many years proved a cost

effective method of protecting pipeline equipment, cleaning
liquids or salvaging valuable solids. The Delta range continues
this tradition and incorporates a number of improved features
and optional extras.
The filter is of cast construction and is supplied with one
high quality stainless steel cylindrical basket. The filter is for use
in liquid handling installations where the flow can be shut off for
short periods to allow the basket to be cleaned.

MAlN FEATURES
High quality 316 grade stainless steel basket with large
filtration areas resulting in low pressure drops.
Compact design for space saving.
Working pressures up to 22 bar.
Quick release filter covers and knobs for easy basket
removal.

OPTIONS
Range of extras allowing filter to be customised
Available in cast iron, cast steel, bronze or stainless steel.
Differential pressure indicators are available.
For details please refer to page 12.

SPECIFICATION
MODEL OV OV/S OV/GM OV/SS

Body Cast Iron Cast Steel Bronze Stainless Steel

material BS1452 BS1504-161 BS1400-LG4C BS1504
Grade 220 min Grade 480 A Grade 316C16

Max. 17 bar 22 bar 22 bar 22 bar

working at 100°C at 100°C at 100°C at 100°C
pressure

Max.
working 250°C (Depending on seal material)
temp.

Baskets Stainless Steel

Basket and Mesh lining BS1449 Grade 316 S31

Drain Brass Steel Phosphor Stainless Steel

plug Bronze

Standard Nitrile Nitrile Nitrile Viton

seals (-35°C to (-35°C to (-35°C to (20°C to
+120°C) +120°C) +120°C) +200°C)

Body
Colour Blue Silver Self Self

Note 1: These specifications refer to standard products only.

Other materials for bodies (e.g. monel, hastalloy) and seals
(e.g. EP, PTFE) are available on request.

Note 2: Higher pressure filters are available up to 40 bar.

Note 3: Working pressure is stated at 100°C. to verify suitability of this

equipment above this temperature or below 0°C, please contact our
help desk.

Note 4: Whilst alternative seal materials e.g. EP, PTFE are available and can
be used to offer a wide range of chemical compatibility and working
temperatures up to 250°C, it is recommended that such applications
are again discussed with our help desk.

4
 AIRPEL SINGLE FILTERS Model OV
Sizes 20mm ( / ”) - 150mm (6”) 3 4

DIMENSIONS & WEIGHTS

SCREWED BSP OR NPT

‘A’ ‘B’ ‘C’ ‘D’ ‘E’ ‘F’ ‘G’ ‘H’ ‘J’ ‘K’ ‘L’ Element Weight
Pipe Size Area (Cast Iron)

20mm 159mm 108mm 103mm 220mm 73mm 105mm 64mm 50mm 86mm 1 2//
/ BSP 184cm2 5 kg
3 4//
/ BSP

25mm 159mm 108mm 103mm 220mm 73mm 105mm 64mm 50mm 86mm 1 2//
/ BSP 184cm2 5 kg
//
1 BSP

32mm 174mm 108mm 129mm 306mm 73mm 145mm 90mm 50mm 122mm 1 2//
/ BSP 268cm2 7 kg
1 4//
1 / BSP

40mm 174mm 108mm 129mm 306mm 73mm 145mm 90mm 50mm 122mm 1 2//
/ BSP 268cm2 7 kg
//
11/2 BSP

50mm 270mm 156mm 165mm 351mm 112mm 156mm 112mm 76mm 131mm 1 2//
/ BSP 484cm2 19 kg
//
2 BSP

65mm 270mm 156mm 165mm 351mm 112mm 156mm 112mm 76mm 131mm 1 2//
/ BSP 484cm2 19 kg
//
21/2 BSP

FLANGED BS10, BS4504, ANSI OR DIN

‘A’ ‘B’ ‘C’ ‘D’ ‘E’ ‘F’ ‘G’ ‘H’ ‘J’ ‘K’ ‘L’ *‘M’ *‘N’ Element Weight
Size Area (Cast Iron)

25mm 194mm 108mm 103mm 220mm 73mm 105mm 64mm 50mm 86mm 1 2 //
/ B.S.P. 124mm 16mm 184cm2 8 kg
//
1
40mm 210mm 108mm 129mm 306mm 73mm 145mm 90mm 50mm 122mm 1/2 B.S.P.//
156mm 18mm 268cm2 12 kg
//
11/2
50mm 310mm 156mm 165mm 351mm 112mm 156mm 112mm 76mm 131mm 1/2 B.S.P.//
165mm 20mm 484cm2 25 kg
//
2
65mm 310mm 156mm 165mm 351mm 112mm 156mm 112mm 76mm 131mm 1/2 B.S.P.//
184mm 20mm 484cm2 25 kg
//
21/2
80mm 343mm 175mm 198mm 451mm 132mm 210mm 140mm 76mm 186mm 1/2 B.S.P.//
210mm 22mm 718cm2 35 kg
//
3 24mm
100mm 356mm 175mm 233mm 575mm 132mm 265mm 175mm 76mm 241mm 1/2 B.S.P. 229mm
//
24mm 964cm2 45 kg
//
4 254mm
150mm 480mm - 288mm 728mm 160mm 353mm 218mm - 330mm 1/2 B.S.P.//
305mm 26mm 1835cm2 99 kg
//
6
*Dimensions above diagonal line are for cast iron filters. Below diagonal line - Steel, Stainless Steel and Bronze

5
 AIRPEL SINGLE FILTER MULTIBASKET Model OV
Sizes 200mm (8”) - 250mm (10”)

The Airpel Single Filter Multibasket design is compact and

easily maintained, with basket removal easier than other units
with similar pipe size connections.
The filter is of cast construction and is supplied with four or
five high quality stainless steel cylindrical baskets depending
upon filter size. The filter is for use in liquid handling installations
where the flow can be shut off for a short period to allow the
baskets to be cleaned.

MAlN FEATURES
High quality stainless steel basket with large filtration areas
resulting in low pressure drops.
Compact design for space saving.
Working pressures up to 13.8 bar.
Quick release filter covers and knobs for easy basket
removal.

OPTIONS
Range of extras allowing filter to be customised.
Available in cast iron, cast steel, bronze or stainless steel
as standard.
Differential pressure indicators are available.
For details refer to page 12.

SPECIFICATION
MODEL OV OV/S OV/GM OV/SS

Body Cast Iron Cast Steel Bronze Stainless Steel

material BS1452 BS1504-161 BS1400-LG4C BS1504
Grade 220 min Grade 480 A Grade 316 C16

Max. 13.8 bar 13.8 bar 13.8 bar 13.8 bar

working at 100°C at 100°C at 100°C at 100°C
pressure

Max.
working 250°C (Depending on seal material)
temp.

Baskets Stainless Steel

Basket and Mesh lining BS1449 Grade 316 S31

Drain Brass Steel Phosphor Stainless Steel

plug Bronze

Standard Nitrile Nitrile Nitrile Viton

seals (-35°C to (-35°C to (-35°C to (-20°C to
+120°C) +120°C) +120°C) +200°C)

Body
Colour Blue Silver Self Self

Note 1: These specifications refer to standard products only.

Other materials for bodies (e.g. monel, hastalloy) and seals
(e.g. EP, PTFE) are available on request.

Note 2: Working pressure is stated at 100°C. to verify suitability of this

equipment above this temperature or below 0°C, please contact our
help desk.

Note 3: Whilst alternative seal materials e.g. EP, PTFE are available and can
be used to offer a wide range of chemical compatibility and working
temperatures up to 250°C, it is recommended that such applications
are again discussed with our help desk.

6
 AIRPEL SINGLE FILTER MULTIBASKET Model OV
Sizes 200mm (8”) - 250mm (10”)

DIMENSIONS & WEIGHTS

Size A B C D E F G H Weight
(Cast Iron)

200mm (8 )
//
200mm 595mm 230mm 308mm 420mm 658mm 610mm 381mm 250kg

250mm (10 ) //
250mm 595mm 276mm 272mm 600mm 848mm 610mm 445mm 409kg

7
 AIRPEL DUAL FILTERS Model OW
Sizes 20mm (3/4”) - 200mm (8”)

For applications where the requirement is for continuous flow

with minimum loss of pressure, the dual filter provides quality of
design and performance.
The filter is of cast construction and incorporates two
chambers each containing a high quality stainless steel basket.
Flow is diverted from one basket to the other without being
interrupted by simply turning the handle which rotates dual
cylindrical cocks.

MAIN FEATURES
Simple changeover operation, requires infrequent
maintenance.
Compact design.
Large filtration areas giving low pressure drops.
Quick release filter covers and knobs for easy maintenance.
No contamination between filtered and unfiltered liquids.
Wide range of materials, sizes and accessories.
Filtration down to 10 microns.
Handle covers chamber in use - preventing accidental
opening of pressurised chamber.
Differential pressure indicators shown in photograph are
optional extras. For details refer to page 12.

MODEL OW/O OW/B OW/S OW/S/WB OW/C OW/GM OW/SS

Body & Cover Cast Iron Cast Iron Cast Steel Cast Steel Cast Iron Bronze Cast St. Steel
material BS1452 BS1452 BS1504-161 BS1504-161 BS1452 BS1400 BS1504
grade 220 min grade 220 min grade 480 grade 480 grade 220 min LG4C grade 316 C16

Sleeve Not Bronze Not Bronze Not Not Not

Applicable BS1400 LG2C Applicable BS1400 LG2C Applicable Applicable Applicable

Change over SG Iron Bronze SG Iron Bronze St. Steel Bronze St. Steel
Cocks BS2789 BS1400 BS2789 BS1400 BS1504 grade BS1400 BS1504 grade
grade 420/12 LG2C grade 420/12 LG2C 316 C16 LG2C 316 C16

(Ni/PTFE coated) (Ni/PTFE coated)

Internal Mild Steel St. Steel Mild Steel St. Steel St. Steel Phosphor St. Steel
Machine BS970 BS970 BS970 BS970 BS970 Bronze BS970
Parts 220 M07 308 S31 220 M07 303 S21 303 S21 BS1400 303 S31
grade PBI

Baskets Stainless Stainless Stainless Stainless Stainless Stainless Stainless

Steel Steel Steel Steel Steel Steel Steel

Drain Brass Brass Mild Steel Brass Stainless Phosphor Stainless

Plugs Steel Bronze Steel

Seals Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Viton

(-35°C to +120°C) (-35°C to +120°C) (-35°C to +120°C) (-35°C to +120°C) (-35°C to +120°C) (-35°C to +120°C) (-20°C to +200°C)

Maximum 17 Bar 17 Bar 22 Bar 22 Bar 17 Bar 22 Bar 22 Bar

Working at 100°C at 100°C at 100°C at 100°C at 100°C at 100°C at 100°C
Pressure

Maximum 200°C 150°C 200°C 150°C 200°C 200°C 200°C

Working Depending on seal Depending on seal Depending on seal Depending on seal Depending on seal Depending on seal Depending on seal
Temp. selection selection selection selection selection selection selection

Body Colour Red Blue Silver Silver Red Self Self

Note 1: These specifications refer to standard products. Other materials for body (e.g, monel, hastalloy) and seals (e.g. EP, PTFE) are available please ask.
Please refer to separate data sheet for details of model OW/HP High Pressure filters for working pressures up to 40 bar are also available.
Note 2: For material selection refer to page 27.
Note 3: Working pressure is stated at 100°C. To verify suitability of this equipment above this temperature or below 0°C, please contact our help desk.
Note 4: Whilst alternative seal materials e.g. EP, PTFE are available and can be used to offer a wide range of chemical compatibility and working temperatures
up to 250°C, it is recommended that such applications are again discussed with our help desk.

8
 AIRPEL DUAL FILTERS Model OW
Sizes 20mm (3/4”) - 200mm (8”)

DIMENSIONS & WEIGHTS

SCREWED BSP OR NPT

A B C D E F G H J K L M N Each Element Weight
Area (Cast Iron)
170mm 1/2 BSP
//
20mm 120mm 270mm 149mm 220mm 73mm 105mm 64mm 175mm 103mm 86mm 184cm2 13kg
3/4//
BSP
170mm 1/2 BSP
//
25mm 120mm 270mm 149mm 220mm 73mm 105mm 64mm 175mm 103mm 86mm 184cm2 13kg
//
1 BSP
184mm 1/2 BSP
//
32mm 137mm 284mm 175mm 306mm 73mm 145mm 90mm 175mm 129mm 122mm 268cm2 19kg
//
11/4 BSP
184mm 1/2 BSP
//
40mm 137mm 284mm 175mm 306mm 73mm 145mm 90mm 175mm 129mm 122mm 268cm2 19kg
//
11/2 BSP
280mm 1/2 BSP
//
50mm 184mm 425mm 223mm 351mm 112mm 156mm 112mm 210mm 165mm 131mm 484cm2 49kg
//
2 BSP
280mm 1/2 BSP
//
65mm 184mm 425mm 223mm 351mm 112mm 156mm 112mm 210mm 165mm 131mm 484cm2 49kg
//
21/2 BSP

FLANGES DRILLED BS10, BS4504, ANSI, DIN OR JIS

A B C D E F G H J K L M N P R Each Element Weight
Area (Cast Iron)
25mm 152mm 270mm 149mm 220mm 73mm 105mm 64mm 175mm 103mm 86mm 170mm 1/2// BSP 124mm 16mm 184cm2 16kg
//
1
//
40mm 175mm 284mm 175mm 306mm 73mm 145mm 90mm 175mm 129mm 122mm 184mm 1/2 BSP 156mm 18mm 268cm2 22kg
//
11/2
50mm 210mm 425mm 223mm 351mm 112mm 156mm 112mm 210mm 165mm 131mm 280mm 1/2// BSP 165mm 20mm 484cm2 52kg
//
2
65mm 210mm 425mm 223mm 351mm 112mm 156mm 112mm 210mm 165mm 131mm 280mm 1/2// BSP 191mm 20mm 484cm2 53kg
//
21/2
//
80mm 267mm 490mm 256mm 451mm 132mm 210mm 140mm 250mm 198mm 186mm 330mm 1/2 BSP 210mm 22mm 718cm2 78kg
//
3
100mm 318mm 540mm 294mm 575mm 132mm 265mm 175mm 250mm 233mm 241mm 380mm 1/2// BSP 254mm 24mm 964cm2 110kg
//
4
150mm
// Available as a Multi-Basket Filter - See insert drawing for dimensions
6
200mm 570mm 1020mm 550mm 1210mm 248mm 520mm 390mm 500mm 436mm 472mm 700mm 1/2// BSP 381mm 30mm 3980cm2 552kg
//
8

A B C D E F G H J Each Element Area Weight

//
6 (150mm) 320 944 472 268 230 286 575 596 2065cm2 250kg

9
 AIRPEL SINGLE FILTERS Model OV
Sizing Data

OV AND OW BASKET
lDENTlFlCATlON
Code numbers are used to identify the
basket as shown on the end plate.
Typical example:
2 A S 80
Mark Size Material Mesh
Mk 1 - None A = 3/4 - 1 //
S = St.St
//

Mk 2 - 2 B = 11/4 - 11/2 // //

// //
C = 2 - 21/2
//
D=3
//
E=4
//
FT = 6 (multi)
//
FV = 6 (OV)
//
G = 8 (OW)
// //
GA / GB=8 / 10 (OV)

PRESSURE DROP CHART

The chart is for water flowing through a
filter without an element. Use the
following correction factors for the
chosen filtration rating and for liquids of
higher viscosity.

EXAMPLES - OV FilTERS CORRECTiON FACTORS FOR OV AND OW

A single basket OV filter is required to protect pipeline Either - multiply the pressure drop for water shown in the chart
equipment to a level of 200 microns. The media is water at by the following correction factors to obtain the actual pressure
20°C, at a pressure of 4 bar g and having a flowrate of 600 drop. (Water has a viscosity of 1 centistoke at 20°C)
litres/min.
Or - divide the acceptable pressure drop by the necessary
A clean basket pressure drop of no more than 34 Kpa is
correction factor in the table below and then use the chart to
acceptable.
determine the filter size and flow rate.
1. Check temperature/pressure rating of filter and suitability for
application, i.e. 20°C temperature at 4 bar g: Filtration Rating
Standard Cast lron Filter suitable Viscosity Unlined 20 mesh 80 mesh 120 mesh 200 mesh
Centistokes Perforated (910µm) (190µm) (130µm) (80µm)
Basket
2. Selection of Mesh: protection to 200 microns or less would
require an 80 mesh basket (At 190 microns, see Standard 1 1 1 1.1 1.25 1.35
Basket Data on page 11.)
50 1.6 1.7 2.1 2.3 2.5
3. Mark flowrate of 600 litres/min on chart 1 to intersect
diagonal “filter selection line” and read vertically to obtain 230 2.0 2.3 3.0 3.35 3.75
pressure drop in Kpa
600 litres/min intersects 65mm (21/2 ) filter and will
// 370 2.2 2.6 3.4 3.8 4.3
have a pressure drop of 28 Kpa.
860 3.0 3.5 4.2 5.0 6.0
4. Apply correction factor for 80 mesh basket:
Pressure drop = 28 Kpa x 1.1 (see table opposite) =
30.8 Kpa
(This falls within acceptable pressure drop of 34 Kpa)
5. Selection for application would be 65mm (21/2 ) cast iron
//

OV filter with an 80 mesh lined basket.

10
 AIRPEL DUAL FILTERS Model OW
Sizing Data

PRESSURE DROP CHART

The chart is for water flowing through a
filter without an element. Use the
correction factors shown on page 10 for
the chosen filtration rating and liquids of
higher viscosity

EXAMPLE - OW FILTERS: STANDARD BASKET DATA FOR OV AND

A dual basket OW filter is required to filter particles the size of OW
80 microns from lubricating oil which has a viscosity of 230 Baskets are constructed from stainless steel perforated plate.
centistokes at 40°C. The flowrate of oil is 150 litres/min at a The relevant degree of filtration is provided by welding the
pressure of l0 bar g. appropriate grade of stainless steel mesh to the basket. Pleated
A clean basket pressure drop of no more than 41 Kpa is elements giving filtration down to 10 microns are also available.
acceptable
Perf. Plate Diameter of hole
1. Check temperature/pressure rating of filter and suitability Holes per Material Percentage
Ref Clear Area
for application, i.e. 40°C temperature at 10 bar g: square inch inches mm µm
Standard Cast lron Filter suitable. 11 0.25 6.35 6350 S11 54
2. Selection of Mesh: Protection to 80 microns or less would 33 0.125 3.17 3170 S33 39
require a 200 mesh basket. (See Standard Basket Data)
124 0.063 1.60 1600 S14 38
3. Mark flowrate of 150 litres/min on chart 2 to intersect
Square mesh Diameter of hole
diagonal “filter selection line” and read vertically to obtain Meshes per Material Percentage
pressure drop in Kpa. Linear inch inches mm µm Ref Clear Area

150 litres/min intersects 50mm (2 ) - 65mm (21/2 )

// //

20 0.036 0.91 910 S20 53

filter and will have a pressure drop of 5.5 Kpa.
30 0.022 0.56 560 S30 42
4. Apply correction factor for oil at 230 centistokes with 200 40 0.015 0.38 380 S40 40
mesh lined basket: (see page 10) 60 0.01 0.25 250 S60 35
Pressure drop = 5.5 Kpa x 3.75 = 20.6 Kpa
80 0.0075 0.19 190 S80 34
(This falls within acceptable pressure at 41 Kpa)
120 0.005 0.13 130 S120 32
5. Selection for application would be 50mm (2 ) or 65mm
//

200 0.003 0.08 80 S200 36

(21/2 ) cast iron OW filter with a 200 mesh lined basket.
//

300 0.002 0.05 50 S300 32

11
 AIRPEL ACCESSORIES
A major feature of the Airpel Filter range is the availability of a
host of optional extras to enable the filter to be tailored to the
customer’s precise requirements.

DIFFERENTIAL PRESSURE INDICATOR

As filter baskets become clogged with debris, the pressure
drop increases. In order to maintain efficient filtration and line
pressure it is important that baskets are cleaned regularly.
The Airpel Differential Pressure lndicator is designed to
monitor basket conditions and provide visual warning that
cleaning is required.
Available as an optional extra on all single, dual and self cleaning
filters, the indicator is mounted directly on to the filter body and
indicates the differential pressure across each basket.

MAlN FEATURES:
Easy to read
Compact Design
No pipework to become clogged
Positive seal separates clean and dirty liquids
Remote operation via electrical signal available if required
Purpose designed for Airpel Filters

SPECIFICATION
Anodised aluminium casing and nitrile diaphragm for water
and oil applications.
Stainless steel casing, stainless steel internals and viton
diaphragm for other liquids.
Indicator preset at 10 psi. Other spring ratings available on
request.
Pointer operated by internal magnet avoiding leakage
through seals.

OPTIONAL EXTRAS WITH FILTERS

Heating Jacket and Immersion Heaters
To aid flow of viscous liquids, etc.
100% Shut Off On Dual Filter Change Over
This can be achieved by use of a special seal within the
change over cock mechanism and eliminates leakage
between chambers during cleaning.
Fully Automated Backflusing
This version of the Dual Filter provides automatic basket
cleaning by reversing the flow within the filter using filtered
liquid to backflush the baskets.
Automatic Air Eliminators
To vent air from filter, eg after element cleaning.
Magnetic Inserts
Suspended from the cover to capture metallic particles.
Magnets can be nylon coated if required.
Mounting Studs or Brackets
To allow the filter to be independently supported.
Pressure Equalising Valves (Dual Filter Only)
Are fitted to sizes 125, 150 and 200mm as standard but
can be fitted to other sizes on request.

12
 AIRPEL SPARES IDENTIFICATION
Single Filter - Model OV

SEAL KIT CONTAINS:

Nitrile, PTFE, encapsulated Viton
Cover ‘O’ rings
Basket ‘O’ rings } EP for Viton
To suit requirement
Bleed Screw Washer
Drain Plug Fibre Washer

O - Rings and Washers only available in

seal kit

13
 AIRPEL SPARES IDENTIFICATION
Dual Filter - Model OW

SEAL KIT CONTAINS: Cover ‘O’ Rings

Basket ‘O’ Rings
Cock Spindle ‘O’ Rings
Drive Shaft ‘O’ Rings
Bleed Screw Washer
Drain Plug Washer
} Nitrile, EP Viton or
Viton Encapsulated
PTFE to suit
requirement

O - Rings and Washers only available in Seal Kit

14
 AIRPEL SELF CLEANING FILTERS (SCF)
Sizes 20mm ( / ”) - 300mm (12”)
3 4

Airpel self-cleaning filters have been designed specifically

to provide efficient filtration of virtually all liquids, including
those of high viscosity, whilst minimising both disruption of
flow and liquid loss during the element cleaning process. There
is no operator contact with the process fluid. The high quality
stainless steel wedge wire (or perforated) element is highly
effective in removing contaminant particles as small as 50
micron (µm).
Cleaning is carried out by rotating the element against fixed
scraper blades which remove debris from the surface of the
element. This in turn is drained from the base of the filter.
The filter is available for either manual or fully automatic
electric or pneumatic operation. The range of optional control
devices make it particularly suitable for continuous processes
and for service with high contamination levels.

RANGE
Airpel offer three forms of blade type self clean fiIter:-
standard range, high pressure range and vertical exit, all
working on the same generic principle. Airpel also offer
both standard element and high pressure element for very
demanding duties
Standard
// //
Models 075, 100, 125, 150, 200, 300 and 400 (3/4 - 4 )
available in detachable head and bowl form, suitable for
TYPICAL APPLICATION working pressures of up to 14 bar and flow rates up to
1500 litres/min.
Adhesives
Vertical Exit
Chemicals // //
Models 150, 200, 300 and 400 (11/2 - 4 ) vertical exit are
Chocolate of cast steel or stainless steel construction for working
Cooling Lines pressures up to 35 bar and flow rates up to 1500
litres/minute
HVAC Water
High Pressure
Inks //
Models 200, 300, 400 and 600 (2”- 6 ), high pressure as
Lacquers illustrated, are cast construction, available in iron, steel
Paints, Stains, Varnishes and stainless steel for working pressures up to 35 bar and
flow rates up to 3000 litres/min.
Petrochemicals
Printing
Fabricated
// //
Models 800, 1000, 1200 (8 -12 ) in fabricated
Recycling Water construction for working pressures to customer
River & Sea Water specification and flow rates up to 18000 litres/min.
Wash Water
BENEFlTS
No operator contact with liquid during cleaning operation.
Minimised product loss - during both process production
and system cleaning.
Increased quality output - minimum disruption to product
flow.
Reduced contamination - less possibility of accidents or
operator exposure to the fluid.
Reduced maintenance costs - automated units can
eliminate manual cleaning.
Environment friendly - enclosed design with minimal
flushing losses.

15
 AIRPEL SCF Standard Range 34
Models: 075, 100, 125, 150, 200, 300, 400, Sizes 20mm ( / ”) - 100mm (4”)

Airpel standard range of self-cleaning filters provide highly

AUTOMATIC cost effective solutions to difficult liquid filtration problems at all
viscosities.

MAIN FEATURES
Simple efficient cleaning process which minimises
disruption to flow
Minimal amount of liquid loss during cleaning process
Suitable for practically all liquids including those of high
viscosity
Filtration levels down to 50 micron
Separate bowl and head secured by Vee clamp allows easy
access to element
Maximum working pressure 14 bar at 100°C
Maximum working temperature 250°C
(dependent on seal material)
High quality 316 stainless steel wound wedge wire or
perforated element

OPTIONS
Filters available in the following materials:
Head: stainless steel, cast steel, cast iron or SG iron
Bowl: stainless steel or mild steel
Range of automated control devices available.
MANUAL
Note 1: Working pressure is stated at 100°C. To verify suitability of
this equipment above this temperature or below 0°C, please
contact our help desk.
Note 2: Whilst alternative seal materials e.g. EP, PTFE are available
and can be used to offer a wide range of chemical
compatibility and working temperatures up to 250°C, it is
recommended that such applications are again discussed
with our help desk.

Cut-away model to show blade and element (stand not included)

16
 AIRPEL SCF Standard Range 34
Models: 075, 100, 125, 150, 200, 300, 400, Sizes 20mm ( / ”) - 100mm (4”)

DIMENSIONS & WEIGHTS

SCREWED FILTERS
Model ‘A’ ‘B’ ‘C’ ‘D’ ‘E’ ‘F’ ‘G’ ‘H’ ‘J’ ‘K’ ‘L’ ‘M’ ‘N’ Wt.
Pipe Size (kg)
075 3 4//
/ BSP 150mm 24mm 266mm 13mm 1 2//
/ BSP 65mm 105mm 450mm 114mm - - - 5.4
// //
100 1 BSP 150mm 24mm 266mm 13mm / BSP
1 2 65mm 105mm 450mm 114mm - - - 5.4
// //
125 11/4 BSP 208mm 32mm 404mm 15mm 1 BSP 120mm (max) 105mm 600mm 155mm 110mm 440mm 490mm 11.2
// //
150 11/2 BSP 208mm 32mm 404mm 15mm 1 BSP 120mm (max) 105mm 600mm 155mm 110mm 440mm 490mm 11.2
// //
200 2 BSP 220mm 40mm 457mm 15mm 1 BSP 140mm 133mm 650mm 155mm 110mm 447mm 540mm 15.2
// //
250 21/2 BSP 220mm 40mm 457mm 15mm 1 BSP 140mm 133mm 650mm 155mm 110mm 461mm 540mm 15.2

FLANGED FILTERS
Model ‘A’ ‘B’ ‘C’ ‘D’ ‘E’ ‘F’ ‘G’ ‘H’ ‘J’ ‘K’ ‘L’ ‘M’ ‘N’ Wt.
Pipe Size (kg)
075 3 4//
/ 210mm 24mm 266mm 13mm 1 2//
/ BSP 65mm 105mm 450mm 114mm - - - -
//
100 1 210mm 24mm 266mm 13mm 1 2//
/ BSP 65mm 105mm 450mm 114mm - - - -
// //
125 11/4 270mm 32mm 404mm 15mm 1 BSP 120mm (max) 105mm 600mm 155mm 110mm 440mm 490mm -
// //
150 11/2 270mm 32mm 404mm 15mm 1 BSP 120mm (max) 105mm 600mm 155mm 110mm 440mm 490mm -
// //
200 2 270mm 40mm 457mm 15mm 1 BSP 140mm 133mm 650mm 155mm 110mm 447mm 540mm 25.0
// //
300 3 300mm 56mm 575mm 20mm 2 BSP 140mm 148mm 875mm 190mm 142mm 461mm 710mm 41.0

//
NOTE: 4 self clean filter information available on request

17
 AIRPEL SCF Vertical Exit Range 12
Models: 150, 200, 300, 400, Sizes 40mm (1 / ”) - 100mm (4”)

Airpel vertical exit range is ideal for the filtration of high value
AUTOMATIC products, as the filter may be drained of fluid at the end of a
batch, making it a cost-effective solution to numerous filtration
applications.

MAIN FEATURES
Product waste kept to a minimum - cost effective for the
filtration of high value fluids
Totally enclosed design - prevents product contamination
and operator exposure to fluid
Filter cleans without disruption to flow - no need to shut
down the line to clean the filter
Quick change components - reduces downtime and loss
of production
Large filtration area elements - give high dirt handling
capacity with low pressure drops
Working pressures up to 35 bar - dependent
on materials of construction
Temperature range up to 250°C - dependent on seal
material used
Eases environmental and safety management requirements
Filtration down to 50 micron

OPTIONS
Optional automation facility - no need for operator
involvement

MANUAL
Note 1: Working pressure is stated at 100°C. To verify suitability of this
equipment above this temperature or below 0°C, please contact
our help desk.

Note 2: Whilst alternative seal materials e.g. EP, PTFE are available and can
be used to offer a wide range of chemical compatibility and working
temperatures up to 250°C, it is recommended that such applications
are again discussed with our help desk.

18
 AIRPEL SCF Vertical Exit Range 12
Models: 150, 200, 300, 400, Sizes 40mm (1 / ”) - 100mm (4”)

DIMENSIONS & WEIGHTS

Model Nominal A B C D E F G H Weight

Bore (Manual) (Kg)

150 40 294 490 764 165 140 120 110 490 40

200 50 294 490 764 165 140 120 110 490 40

300 80 400 630 900 210 185 150 150 450 60
400 100 650 880 1150 510 185 400 150 700 180

19
 AIRPEL SCF High Pressure Range 12
Models: 200HP, 300HP, 400HP, 600HP. Sizes 40mm (1 / ”) - 300mm (12”)

Airpel higher pressure range of self-cleaning filters have

AUTOMATIC been used successfully on many difficult liquids handling
installations throughout the world.

MAIN FEATURES
Simple efficient cleaning process which minimises
disruption to flow
Minimal amount of liquid loss during cleaning process
Suitable for practically all liquids including those of high
viscosity
Filtration levels down to 50 micron
lntegral cast construction
Maximum working pressure 35 bar at 100°C
Maximum working temperature 250°C
(dependent on seal material)
Available in cast iron, SG iron, cast steel,
stainless steel or gun metal
High quality 316 stainless steel wound wedge wire or
perforated element

OPTIONS
Range of automated control devices available
Heating jackets
MANUAL
Note 1: Working pressure is stated at 100°C. To verify suitability of this
equipment above this temperature or below 0°C, please contact
our help desk.

Note 2: Whilst alternative seal materials e.g. EP, PTFE are available and
can be used to offer a wide range of chemical compatibility and
working temperatures up to 250°C, it is recommended that such
applications are again discussed with our help desk.

20
 AIRPEL SCF High Pressure Range
Models: 200HP, 300HP, 400HP, 600HP. Sizes 40mm (11/2”) - 300mm (12”)

DIMENSIONS & WEIGHTS

Model ‘A’ ‘B’ ‘C’ ‘D’ ‘E’ ‘F’ ‘G’ ‘H’ ‘J’ ‘K’ ‘L’ ‘M’ ‘N’ ‘P’ ‘R’ ‘S’ Wt. Wt.
Pipe Manual Auto
Size (kg) (kg)

40 mm*
200 11/2 in 270mm 150mm 195mm 413mm 150mm 325mm 115mm 140mm 540mm 150mm 124mm 110mm //
1 BSP 165mm 25 36 44

50 mm
2 in

80 mm
//
300 3 in 360mm 210mm 230mm 690mm 180mm 430mm 140mm 140mm 575mm 180mm 124mm 142mm 2 BSP 210mm 22mm 55 63

100 mm on on
//
400 4 in 550mm 315mm 435mm 1115mm 340mm 665mm 235mm 406mm 880mm 332mm - 150mm 2 BSP 254mm 30mm req. req.

150 mm on on
//
600 6 in 550mm 315mm 435mm 1550mm 340mm 1165mm 235mm 406mm 880mm 332mm - 150mm 2 BSP 318mm 35mm req. req.

*40 mm size units offered in screwed version only. Larger sizes on request.

21
 AIRPEL SCF Sizing Data
Models: 075-800

AUTOMATED SELF
CLEANING FILTERS
The Airpel automated self cleaning filter
allows for stand alone, low maintenance
processing of liquids.
The range can be automated, either
electronically or pneumatically, from
PRESSURE DROP CHART 32mm (11/4 ) and above. The filters can
//

The chart is for water flowing through a filter without an element. be supplied wired and fully tested,
Use the following correction factors for the chosen filtration requiring only on site connection to the
rating and for liquids of higher viscosity power source.
Further information available on request.
CORRECTION FACTORS
Either - multiply the pressure drop for water shown in the chart
by the following correction factors to obtain the actual pressure
drop. (Water has a viscosity of 1 centistoke at 20°C)
Or - divide the acceptable pressure drop by the necessary
correction factor in the table below and then use the chart to
determine the filter size and flow rate.

Filtration Rating
Viscosity
Centistokes 1000µm 500µm 200µm 100µm 50µm

1 1 1 1.1 1.2 1.45

50 1.4 1.8 2.1 2.3 2.5

230 1.70 2.5 3.0 3.35 3.75

370 1.8 3.0 3.4 3.8 4.3

860 2.6 3.7 4.2 5.0 6.0

22
AIRPEL SCF SPARES IDENTIFICATION

23
 AIRPEL Y-TYPE STRAINERS
Carbon Steel & Stainless Steel

Airpel’s Y-type strainers are the economic way of protecting

pipeline equipment from harmful debris.
These strainers have been designed using the latest
computer technology to give optimum dynamic performance
combined with enhanced reliability and ease of maintenance.
The element can be cleaned without stopping the flow or
dismantling the strainer by means of an optional manual purge
valve fitted onto the cover. This valve will allow debris to be
quickly and efficiently removed from the element to maintain
optimum performance.

MAIN FEATURES
lnnovative self-aligning element location
O-Ring cover seal
Large filtration area elements
Advanced dynamic flow paths
Differential pressure monitoring facility (Flanged Strainers)
Heavy duty cast metal construction
Temperature range up to 250°C (Dependent on Seal
Material)
Stainless steel 316 elements
Filtration down to 50 micron
Working pressures up to 40 bar
Designed and tested to BS 5500/ASME Vlll
// //
Sizes from 12mm (1/2 ) to 200mm (8 )
Screwed, flanged or socket weld connections

FLOW CHARACTERlSTlCS
The chart is for water flowing through a strainer without an
element. Use the following correction factors for the chosen
filtration rating and for liquids of a higher viscosity,

Correction Factors
Either - Multiply the pressure drop for water shown in the chart
by the following correction factors to obtain the actual pressure
drop. (Water has a viscosity of 1 centistoke at 20°C).
Or - Divide the acceptable pressure drop by the necessary
correction factor in the table below and then use the chart to
determine filter flow and size.

Viscosity Filtration Rating

Centistokes 20 Mesh 80 Mesh 120 Mesh 200 Mesh
910 micron 190 micron 130 micron 80 micron
1 1.0 1.1 1.25 1.35
50 1.7 2.1 2.3 2.5
230 2.3 3.0 3.35 3.75
370 2.6 3.4 3.8 4.3
860 3.5 4.2 5.0 6.0
Note 1: Working pressure is stated at 100°C. To verify suitability of this
equipment above this temperature or below 0°C, please contact
our help desk.
Note 2: Whilst alternative seal materials e.g. EP, PTFE are available and can
be used to offer a wide range of chemical compatibility and
working temperatures up to 250°C, it is recommended that such
applications are again discussed with our help desk

24
 AIRPEL Y-TYPE STRAINERS
Carbon Steel & Stainless Steel

DIMENSIONS

SCREWED FLANGED
A

SPACE TO WITHDRAW ELEMENT

D
OD

SPACE TO WITHDRAW ELEMENT

B
C

B
C

Nominal A B C D Nominal A B C D
Bore Bore
1/2// BSPP 78 50 72 28 //
50mm (2 ) 230 150 230 165
3/4// BSPP 93 60 88 35 //
80mm (3 ) 310 225 350 210
//
1 BSPP 108 70 105 42 100mm (4 ) //
350 245 360 235

11/4 BSPP 128 82 124 51 //

//
150mm (6 ) 480 370 560 320

11/2 BSPP 143 91 142 57 //

//
200mm (8 ) 600 505 740 380
//
2 BSPP 173 118 188 69

25
 AIRPEL TEMPORARY STRAINERS
Equipment requiring protection will have permanent strainers
fitted in the piping system and the range illustrated in this
catalogue will meet these needs.
However, temporary strainers are necessary when
commissioning plant after construction or during maintenance to
remove flow debris. This is generally of a coarse nature and can
cause considerable damage to equipment and pipelines.
Our standard range is illustrated and available in the
materials shown.
Two basic constructions exist; one being perforated plate
and the other supported woven wire mesh. Strainer top rings are
suitable for standard flange faces and have integral identification
tags. Separate spacer rings for insertion after removal of
temporary strainers are available (if required).
Standard strainer top rings are as illustrated and will fit most
flanges. Other top rings available on request.

MATERIALS
SS 316 or 304.

25
L

A DIA B DIA
FLOW

2 or 3

Pipe Size Assembly A dia B dia C L

part no.
//
25mm (1 ) C14196 68 22 98 50

32mm (11/4 ) //
C14197 80 32 108 54

40mm (11/2 ) //
C14198 80 32 108 54
//
50mm (2 ) C14199 98 44 121 64

65mm (21/2//) C14200 118 57 127 76

//
80mm (3 ) C14201 130 70 143 76
//
100mm (4 ) C14202 168 92 178 127
125mm (5”) C14203 191 118 191 140
150mm (6”) C14204 216 140 197 152
//
200mm (8 ) C16152 272 178 273 254
//
250mm (10 ) C16153 333 229 318 254

26
 AIRPEL FILTER APPLICATION DETAILS (QUESTIONNAIRE)

Customer Name: Industry Type:

Contact Name: Phone Number:

BASIC APPLICATION DETAILS:

Liquid: Viscosity: Specific Gravity:

Flow Rate: Operating Temperature: Operating Pressure:

Filtration Required: Type of Dirt/Debris: % of Dirt if known:

Planned Use i.e.: Can Liquid Flow be interrupted: Acceptable Clean pressure drop:
Suction / Discharge Yes / No

Material: Filter Body Connections: Drilling if Flanged:

Element - Flanged
Seal - Screwed

OPTIONS FOR CONSIDERATION

Heating Jackets:
- Full - Material - Temperature
- Half - Pressure - Connections
DP Gauge Indicators: Magnetic Inserts: Immersion Heaters:
Stainless Steel - Coated
Aluminium Alloy - Uncoated
Auto Air Eliminators: Pressure Equalising Line: 100% Shut Off:

Mounting: Special Finishes: Filter Proposed:

- Studs
- Brackets

AUTOMATION REQUIREMENTS
Motor: DP Switch: Dump Valve:
- Voltage
- Phase
Control Box: Zone Requirements: Special Requirements:
- Self Clean ‘A’ or ‘B’ - Yes
- Backwash - No

DOCUMENTATION REQUIREMENTS
API, ASME VIII etc.: Certificates: Drawings:

Inspection: Packing Instructions: Delivery Instructions:

This document is intended for guidance only.

Customers should satisfy themselves that the filter/strainer specified is suitable for its intended use.

30
OTHER FILTERS OFFERED BY AIRPEL
API FILTERS
Airpel manufacture a range of API filters for the oil and offshore industry. These units
manufactured in cast steel and stainless steel offer fine filtration down to 10µm. The
filters are in accordance with the latest API specification and are available with ASME Vlll
calculations.
Sizes available as standard 25mm - 100mm (1 -4 ) with flow rates up to 1500 litres per
// //

minute.

AIRPEL BACKWASH STRAINERS

Airpel are the UK distributor for the ‘Kinney’ range of backwash strainers. These
strainers offer a compact, rugged construction with optional automatic backwash control
for intermittent flushing and a shearing action to break up debris extending beyond the
strainer media. The strainers are capable of functioning on the suction and discharge
side of the pump without any disruption to flow and are available in cast iron, aluminium
bronze or stainless steel materials dependent upon application.
Sizes available 50mm - 1220mm (2 -48 ).
// //

Typical applications are in industrial plants where the continuous removal of suspended
particles is essential during cooling, descaling, bearing lubrication, spraying and
quenching etc.

AIRPEL VIBRATORY SIEVE

Airpel the UK distributor for the ‘Vorti - Siv’ range of vibratory sieves. One of the most
effective sieve and straining machines available, versatile enough to process both wet
and dry substances including powders, liquids and slurry with no special adaption. The
unit uses a unique gyratory motion generated by an adjustable off - balance driven
flywheel. Product contact parts are 304 or 316 stainless steel with non contact parts
available painted, epoxy or PTFE coated or stainless steel.
Sizes available 200mm - 915mm (8 -36 ).
// //

SERVICES
Airpel is in the position to offer special designs to meet industry requirements. One of
the prime examples of this ability was shown when a major paint manufacturer came to
Airpel to develop a mobile filtration unit for batch runs. Airpel has the expertise and
products to develop systems to meet specific customer applications.
Airpel can provide a service engineer either as part of a service contract or in the form
of an individual site visit. All service engineers are skilled technicians trained to offer a
complete range of skills necessary for the overhaul and commissioning of Airpel
Filtration equipment.

31
INTRODUCTION

Airpel Filtration Mission Statement

To establish Airpel as the number one manufacturer
of industrial strainers through market leading product
design and excellence in customer service.

Airpel Filtration
Bishops House
Market Place
Chalfont St Peter
Buckinghamshire SL9 9HE
England

Tel: 01753 889251

Fax: 01753 887251

DOCTDS-03-1SS0-10/01-ISS.1
AIRPEL
F I L T R A T I O N