Revised 3/07/11

GUIDELINES FOR LIME STABILIZATION

I. Why Use Lime?

Lime Stabilization has the potential to reduce initial construction costs through improved
subgrade stability and reductions in pavement structure. Lime can also provide greater long term
stability of the pavement structure and lower pavement life-cycle costs through reduced
pavement maintenance.

Lime is primarily for use on high clay content soils. Lime stabilization has been used
successfully on projects in both south and northwest Georgia to improve very poor subgrade
soils, increase the soil support value and eliminate wasting bad soils. Refer to the following
pages for more information on selecting and using lime on projects.

If the majority of the soils on a project are IIIC and/or poor quality IIB4 soils in both cuts and
fills, lime stabilization may be considered for use. If the soils are very micaceous, however, do
not use lime, as it does not react well with micaceous soils. Use cement stabilization for
micaceous soils. Research shows that 6% cement mixed 9 inches deep is the optimum
combination for economics and strength for stabilizing micaceous soils.

Whenever the majority of the soils on a project have the following test results, consider using
lime stabilization:

Plasticity Index > 15-18

Volume Change > 20-30%

Clay Content > 25-30%

When dealing with these type soils, always recommend lime stabilization to the outside edges of
the shoulders.

When lime stabilization is recommended, the soil support value (SSV) may be raised to 3.5 or
4.0. Remember to state in the soil survey report that the SSV is based on using lime stabilization.
Also consider the higher SSV when making your recommendation for the depth of GAB on
Piedmont projects.

4.5.33
II. Is Lime Right for My Project?

If you are evaluating a project for lime stabilization, several things must be considered to ensure
that lime stabilization is feasible for the project. Soil conditions are a primary factor in
determining whether lime stabilization is appropriate. However, there may be conditions where
the soils are well suited to lime stabilization but cost and constructability issues may make lime
not feasible to use. Also, because lime is recognized as having some potential health and safety
issues, it is important that appropriate measures be taken to ensure that these concerns are
addressed during construction especially if the project is in an urban area. Consider the following
factors when evaluating the constructability of lime on your project:

1. Project Length

When determining whether to use lime, consider the length and width of the project. It
must be long enough and wide enough to accommodate tanker trucks, motorgraders,
harrows, mixers and compacting and finishing equipment.

2. Variable Alignment

If the alignment will be shifting frequently, i.e., narrow width construction (10 feet to
wedges), lime is typically not recommended for this type construction due to the required
“safe-ing” o f t h e d r o p -offs a d j a c e n t t o t r a v e l l a n e s . Using a s o i l s u p p o r t
v a l u e representing the untreated soil along with a minimum of 8 to 12 inches of GAB (8
to 10 inches for state routes and urban business areas and 12 inches for interstates) plus an
additional 4 inches of GAB for problems areas would be more appropriate here.

3. Widening symmetrically from 2 lanes to 4-5 lanes (with or without curb and gutter)

Lime stabilized subgrade can be successfully constructed with this configuration unless
the project is in a heavily business laden area which requires frequent and immediate
access to businesses. If there are a significant number of businesses, GAB construction
may have to be recommended instead of lime.

4. New Construction (2-lane, 4-lane or addition of 2 new lanes)

This is the best scenario for lime stabilized subgrade as far as alignment is concerned
because there are minimal to no traffic concerns.

5. Rock

Projects located along the Fall Line and north of the Fall Line should be evaluated for the
presence of rock that could be expected at grade, especially in the Ridge and Valley
Region. The materials here are typically plastic cherty clays or shaley clays that normally
would be well suited for lime stabilization, but there are also chert boulders, rock
fragments and rock layers in this region, and this has the potential to cause severe
wearing of the mixing equipment during the lime operations. If large quantities of rock
 are present, include a statement in the lime section of the soil survey report that the
contractor should be aware of this condition. Look at the boring logs in the cuts and get
an idea of how much rock is on the project, how much is above grade, how deep are the
fills and where the rock is likely to end up at grade.

III. How Much Lime is Needed?

The range of lime to use is normally 4 to 6 percent and is based on the soil types on the project-
the worse the soils, the higher percentage of lime should be used. Stabilization should be a
minimum of 6 inches deep for marginal soils (near the lower to mid range of the test results
listed above); 8 to 9 inches for poorer soils and 10 to 12 inches for the very worst soils. If there is
little experience in dealing with lime, the proper way to determine the optimum amount of lime
is to do CBR testing with raw soil using 4, 5 and 6% lime.

When calculating lime quantities, the designers must consider the type of application. For
hydrated lime, the amount to use is based on the dry weight of the soil. For quicklime, you must
use the formula in Section 225 to get the correct amount. Since quicklime contains no water, the
amount of lime required is slightly less than that of hydrated lime (see formula in Section 225
Specification).

IV. Are There Any Weather Limitations?

When using hydrated lime, the time frame in Section 225 should be strictly adhered to (usually
April to November) because lime stabilization needs a sufficient amount of heat to react. At less
than 40 degrees Fahrenheit, lime will be dormant and not begin to react with the soil.

When using quicklime, the construction dates can be extended because the slaking process
generates a generous amount of heat and causes the lime to react more quickly with the soil, even
in cool weather.

V. What Are the Types of Lime?

A. Lime Types

The two types of lime used on construction are hydrated lime and quicklime. They can be
applied dry or in slurry form with some precautions.

1. Hydrated Lime

Hydrated lime is lightweight. Although it contains about 30% moisture, it is extremely

dusty and requires special application equipment to distribute it on the roadway. Dry lime
is primarily used in rural areas and never for airport reconstruction, as the calcium in the
lime will damage aluminum on aircraft. However, hydrated lime can be used in slurry
form almost anywhere.
 2. Quicklime

Quicklime contains no water and is very caustic to the skin. Sever burning of the skin can
occur if safety precautions are not observed.

Because of its caustic nature, quicklime is normally shipped and used in pebble form
(approximately sieve size #4 up to ¾ to 1”) to minimize dusting. Lime pebbles are
usually spread on the ground through bottom dump trailers.

Quicklime must be “slaked” on the roadway or in the mixing chamber of the mixer
(water added to make the lime dissolve into slurry form). Large pebbles require much
more work to slake. If not properly slaked, the pebbles can swell in the soil and cause
pavement failure.

Quicklime is normally used in slurry form that is prepared in a slaking tank on the
project. The lime slurry is hauled to the roadway and placed via special slurry tanks with
agitators to keep the lime in suspension during transport and placement.

B. Classes of Construction (see Standard Specification Section 225)

1. Class A- Used for extremely poor soils (PI> 45 to 50). Lime is applied in 2 applications
with a minimum 12-hour and maximum 72-hour mellowing period between applications.

2. Class B- Used for moderately poor soils. This class is the most commonly one used.
Lime is applied in one application with a minimum 12-hour and maximum 72-hour
mellowing period before final processing.

2. Class C- Used for marginal soils that are typically workable but need some reduction in
plasticity. This class is rarely used on DOT projects. Lime is applied, mixed, shaped and
final graded to receive the next layer in the pavement system. There is no mellowing
period for this type construction.

Specify in the soil survey report which class of lime should be used.